Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver

Attention Forum Users: On the 28th of December 2023 at 9:00am Central Time, we will be taking the forums down for maintenance while we prepare the new forums for your use. Please click here for more information.

Case Tractors Discussion Forum
:

another Axle seal queston

Welcome Guest, Log in or Register
Author 
mike

03-04-2004 08:57:31




Report to Moderator

ok, after a few case dumbfounded case dealers, I called the smallest one I could find and he found that maybe the number A30529 should be A30526. I think it cross referenced to the CR 25745 number and they are about #40 for a seal. What I need to know is if that is for both inner and outer or just one or the other and which is it. From what I can tell by my book, there is a inner seal then the bearing then an outer seal or felt.

Hey F-I-T, do you remember which is which.

thanks in again for all the help.

[Log in to Reply]   [No Email]
F-I-T

03-04-2004 10:30:46




Report to Moderator
 Re: another Axle seal queston in reply to mike, 03-04-2004 08:57:31  
Mike:

I'm 2,000 miles away from my notes, so I just do not know. Have you tried going down to the NAPA and looking at their seal cross reference book? If they have the seals in stock you'll be able to make some measurements. Also, when you get an old one out, you'll be able to take some measurements. On a few of mine, I looked through their book, dimension by dimension, and got a good sub that way.

It can take a bit of time.

Frank

[Log in to Reply]  [No Email]
Dug G.

03-04-2004 12:10:54




Report to Moderator
 Re: Re: another Axle seal queston in reply to F-I-T, 03-04-2004 10:30:46  
For our SC seals, we were able to give the number off the seal(national and case numbers), and they were able to crossreference them. It was a lot cheaper then going to case, since they swore up and down there was no such tractor. good luck.



[Log in to Reply]  [No Email]
Ol Chief

03-04-2004 21:23:41




Report to Moderator
 Re: Re: Re: another Axle seal queston in reply to Dug G., 03-04-2004 12:10:54  
This is not a smart remark,but I am baffled.If the bearing is sealed on both sides where does it get it's lubrication.Can't say that I have seen this type axle bearing set up.



[Log in to Reply]  [No Email]
Klyde

03-04-2004 23:33:44




Report to Moderator
 Re: Re: Re: Re: another Axle seal queston in reply to Ol Chief , 03-04-2004 21:23:41  
From a grease zerk.



[Log in to Reply]  [No Email]
Joe (Wa)

03-04-2004 23:22:23




Report to Moderator
 Re: Re: Re: Re: another Axle seal queston in reply to Ol Chief , 03-04-2004 21:23:41  
The bearing is not sealed on both sides. All Vac's that I have seen have flooded axles, there is one seal outboard of the bearing.

The problem is the Case parts counter person looks in the parts manual showing an exploded view of one axle with seal p/n vt3479(2) or newer nr a30529(2) and tells you that it takes two seals. Well yeah, if you are doing both axles you need two.

a30529 was a good nr for this seal 4 years ago and I doubt that p/n has been superseded.

Frank has the best advice, measure the OD of the axle and ID of the axle housing in way of the seal, take the measurements and the old seal to a vendor like Napa and match it. It is a common lip seal, probably National brand or possibly Chicago Rawhide. If the outer casing of the seal has a stamped number that is eroded by rust it may be legible on the inside.

So ol Chief, I am an old Chief too. Shame of you for not having a manual for your 580. Wish I could help you but alas I know nothing but Va & 300 series and not a whole lot about them.

Joe

[Log in to Reply]  [No Email]
Mike

03-05-2004 05:44:24




Report to Moderator
 Re: Re: Re: Re: Re: another Axle seal queston in reply to Joe (Wa), 03-04-2004 23:22:23  
Thanks guys. I was looking at my service manual and from the bad pictures it looked as it said there were 2 seals, inner and outer. It didn't make sense to me either how the bearing got lub'd.



[Log in to Reply]  [No Email]
Joe (Wa)

03-05-2004 09:30:35




Report to Moderator
 Re: Re: Re: Re: Re: Re: another Axle seal queston in reply to Mike, 03-05-2004 05:44:24  
Perhaps the bearing cone is being mistaken for a seal in a fuzzy pix. On my '53 the outer bearing parts in order from the outside in are:

1. oil seal
2. washer
3. taper bearing
4. bearing cone
5. snap ring

Earlier model VAC may be different but I doubt it.



[Log in to Reply]  [No Email]
[Options]  [Printer Friendly]  [Posting Help]  [Return to Forum]   [Log in to Reply]

Hop to:


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Copyright © 1997-2023 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy