TRACTOR PARTS Allis Chalmers Case & David Brown Farmall & International Ferguson Ford & New Holland John Deere Massey Ferguson Massey Harris Minneapolis Moline Oliver & Cockshutt Kubota / Yanmar

TRACTOR MANUALS

Allis Chalmers	Case	Farmall IH	Ford 8N,9N,2N	Ford
Ferguson	John Deere	Massey Ferguson	Minn. Moline	Oliver

Case Tractors Discussion Forum

Hey Campbell- here's the cup dimensions...

Welcome Guest, Log in or Register

Author

Mike Schotte

02-08-2004 08:43:26

Report to Moderator

Campbell-

I still haven't gone shopping for stainless steel mixing cups at the commercial kitchen store yet-

But I thought I'd post the dimensions you asked me for earlier in the week. Maybe you can find one on your end of the world, too:

Case SC oil cup

Outside diameter at lip: 5-3/8" (+/- 1/16")

Inside clear diameter: 5-1/8"

Overall Height: 3-1/2" (+/- 1/16") [1-3/4" vertical, 1-3/4" curved]

Base (Flat circle at bottom of cup:) 7/8" dia.

That's the best I can do on this cup, it's a little dinged up.

third party image

-Schotte

[Log in to Reply] [No Email]

Campbell

02-08-2004 21:19:01

Report to Moderator

Re: Hey Campbell- here's the cup dimensions... in reply to Mike Schotte, 02-08-2004 08:43:26

Thanks for the dimensions. So far no luck in finding another by scanning the web through various cooking suppliers. I know that there was a similar mixing bowl made once, as I have one that came with my first house. Unfortunately I dont know the source, but the dimesions are just about dead on other than the bottom being a little flatter. They probably stopped making them because as a mixing bowl its pretty tippy. Also it has a hinged, hanging loop tacked on one side. Will keep looking though. Do a lot of people need these?

[Log in to Reply] [No Email]

Glenn F.

02-08-2004 18:19:47

Report to Moderator

Re: Hey Campbell- here's the cup dimensions... in reply to Mike Schotte, 02-08-2004 08:43:26

Boy, nothing like getting personal. What cup size are you? I had to add this. The teenager in me I guess. Glenn F.

[Log in to Reply] [No Email]

todd (dimples) hamilton

02-08-2004 13:38:54

Report to Moderator

Re: Hey Campbell- here's the cup dimensions... in reply to Mike Schotte, 02-08-2004 08:43:26

Mine has a dimple in the bottom of the cup for the ball on the bail to snap into. Does your cup have a dimple?:^)

[Log in to Reply] [No Email]

Mike Schotte

02-08-2004 17:53:00

Report to Moderator

Re: Re: Hey Campbell- here's the cup dimensions... in reply to todd (dimples) hamilton, 02-08-2004 13:38:54

Hey Todd,

Mine had a small dimple in the middle, and two "troughs" that were dented in leading to the middle. Looked like a spot where the wheel had been rolled (or forced) time and time again. Wore a pinhole at the crease that I plan to solder tomorrow.

I took a steel bar and a ball peen hammer today and took out all the dimples I could beat on.

Maybe I took out one too many??!

-Schotte

[Log in to Reply] [No Email]

[Options] [Printer Friendly] [Posting Help] [Return to Forum] [Log in to Reply]

TRACTOR PARTS	TRACTOR MANUALS

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home | Forums

Copyright © 1997-2023 Yesterday's Tractor Co.
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy