Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver

Attention Forum Users: On the 28th of December 2023 at 9:00am Central Time, we will be taking the forums down for maintenance while we prepare the new forums for your use. Please click here for more information.

Case Tractors Discussion Forum
:

Soldering question for Klyde

Welcome Guest, Log in or Register
Author 
Mike Schotte

11-03-2003 12:27:01




Report to Moderator

Hey Klyde,

I think I'm going to take your advice about building up the tank threads on the SC gas tank with solder. I'll then re-tap them for a tighter fit.

I already have one tiny pinhole in the lower part of the tank to solder, so I might as well do both while I'm there.

How would you recommend doing it? I never know how to get enough heat into the piece when there's so much adjacent metal that always dissipates the heat too quickly.

I'm thinking you would use a propane torch to heat the threads instead of trying to transfer heat with a soldering iron. The problem is to get the thread hot enough, but not heat it up enough to melt the solder that holds the drain neck onto the tank body.

What do you suggest?

(Before anybody asks- this tank hasn't had gas in it for at least 10 years, has been boiled out and has had the inside scoured out and washed.)

-Schotte

[Log in to Reply]   [No Email]
David Bacon

11-05-2003 19:53:13




Report to Moderator
 Re: Soldering question for Klyde in reply to Mike Schotte, 11-03-2003 12:27:01  
Perhaps I just crawled out from under a rock, but has anyone ever tried JB weld? I think some of my escapades with JB and sedment bulbs go back 20 years or so, and still no leakey. clean is a must--- Dave NE Iowa



[Log in to Reply]  [No Email]
Brad From Australia

11-05-2003 18:19:29




Report to Moderator
 Re: Soldering question for Klyde in reply to Mike Schotte, 11-03-2003 12:27:01  
Bit of advice.
I weld up petrol (gas) and diesel tanks more often than I'd like. Simply fill them with soapy water to the brim to eliminate all air space. Only problem can be the steam produced but if you wear a set of welding gloves that's not a problem. As for the fitting coming out from the heat, let it, stick it in a vice, braze it up, tap it then resolder it back into the tank.
Too easy. Hope it helps.
Cheers Brad

[Log in to Reply]  [No Email]
GeoMo

11-04-2003 05:04:41




Report to Moderator
 Re: Soldering question for Klyde in reply to Mike Schotte, 11-03-2003 12:27:01  
Since pipe threads are tapered can the fitting be shorten then retapped?



[Log in to Reply]  [No Email]
AZ Jack

11-03-2003 18:15:59




Report to Moderator
 Re: Soldering question for Klyde in reply to Mike Schotte, 11-03-2003 12:27:01  
Since this may be your last post Schotte if you go with flame heat, I want you to know I have enjoyed reading your posts from time to time. Seriously find another way-the soldering irons ground to fit seems like would work or helicoil maybe.



[Log in to Reply]  [No Email]
Mike Schotte

11-03-2003 18:48:39




Report to Moderator
 Re: Re: Soldering question for Klyde in reply to AZ Jack, 11-03-2003 18:15:59  
It's nice to know ya'll care.

I've read all the horror stories about folks blowing themselves up- and all the crazy ways that folks have invented trying to NOT blow themselves up, too... but I would be INCREDIBLY surprised if there was anything left inside this tank but flakes of rust.

It's been bone dry for years and years, and I've washed and scrubbed and abraded the heck out of it. I don't see how there's any way that a flammable vapor could remain inside the tank- it has no smell whatsoever.

-S.

[Log in to Reply]  [No Email]
todd hamilton

11-03-2003 19:16:41




Report to Moderator
 Re: Re: Re: Soldering question for Klyde in reply to Mike Schotte, 11-03-2003 18:48:39  
Be sure to get ALL of the sand out of the tank if you sandblasted it on the inside. The fellow who did mine did not get it all out and after four years I still am wiping that crud out of the bowel every few months. I'm sure that it does the carb and engine well to run that sand into it. Automatic internal parts polishing system!



[Log in to Reply]  [No Email]
todd hamilton

11-03-2003 16:34:38




Report to Moderator
 Re: Soldering question for Klyde in reply to Mike Schotte, 11-03-2003 12:27:01  
KA-BOOM! :)



[Log in to Reply]  [No Email]
JohnM

11-03-2003 15:05:14




Report to Moderator
 Re: Soldering question for Klyde in reply to Mike Schotte, 11-03-2003 12:27:01  
Hey Mike before you go with that, can you get a heli-coil in there or can you drill it out to say 1/2 inch pipe (whatever size that really is) and then put a reducer in it. It is easier to make a hole bigger than it is to make it smaller with solder I would think. Good luck.



[Log in to Reply]  [No Email]
Klyde

11-03-2003 14:53:33




Report to Moderator
 Re: Soldering question for Klyde in reply to Mike Schotte, 11-03-2003 12:27:01  
I use the big old soldering coppers that are probably 100 years old . Heat them up on a blowtorch or whatever has clean hot flame. I've got some ground round so they fit right in. Usually heat one while I'm using the other. Acid and acid core solder should get the job done. I don't use a torch much right on the tank when soldering,bad experience long ago! ( no gas in that tank for a long time either)

[Log in to Reply]  [No Email]
[Options]  [Printer Friendly]  [Posting Help]  [Return to Forum]   [Log in to Reply]

Hop to:


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Copyright © 1997-2023 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy