Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver

Attention Forum Users: On the 28th of December 2023 at 9:00am Central Time, we will be taking the forums down for maintenance while we prepare the new forums for your use. Please click here for more information.

Discussion Forum
:

VAO oil filter stick broken tube fix it or plug it

Welcome Guest, Log in or Register
Author 
Ted in Sacramen

04-12-2003 18:16:51




Report to Moderator

I have been through the archives and read about the bypass system for the oil filter on the VA series tractors. I have the apparently often broken oil tube on my VAO, my oil pressure with this tube broken and an old filter in place was approximately 13 pounds consistent throughout the entire rpm range (idle to whatever working, original gauge). Have removed the valve cover as advised in earlier question here (YT) and rocker arm has good lubrication. Is the fitlter practical and efficient enough to repair and return to service or should I plug and be done with it? Haven't decided but I'd appreciate opinions as to the efficientcy of this not inline system. Thanks for all the help, from stuck to the envy of the neighborhood, all my help has come from this board, I hope to get a picture to post soon.

[Log in to Reply]   [No Email]
mj

04-15-2003 13:31:31




Report to Moderator
 Re: VAO oil filter stick broken tube fix it or plug it in reply to Ted in Sacramento, 04-12-2003 18:16:51  
I just changed the oil on one of my VACs and used a Car Quest filter (#85101) and it did not have the wooden stick inserted to keep the filter media separted until installation. There is a rubber 'nipple' that extends to near the filter base with a hole molded into the nipples' center. This hole is an inerference fit with the filter housing standpipe that we've been discussing. When I tried to put the filter on it wouldn't come down enough to thread into the base SO I measured the remaining distance to the housing and added a 1/2". I cut that much off off the standpipe which is one I made out of copper tubing years ago and put it together...seems to work fine. Evidently the filters have been redesigned internally to eliminate the 'loose media' configuration of the originals. By the way, I never crimp or cross-drill the end of the tubes; just cutting them with my somewhat dull tubing cutter produces a tapered end and reduced diameter to the point where a bit of re-opening of the tube with a small drill is necessary. :-)

[Log in to Reply]  [No Email]
mj

04-15-2003 13:36:12




Report to Moderator
 Re: Re: VAO oil filter stick broken tube fix it or plug it in reply to mj, 04-15-2003 13:31:31  
SEPARTED????....should be SEPARATED....gotta work on my brain to fingers interface! :-)



[Log in to Reply]  [No Email]
Joe (Wa)

04-14-2003 18:56:37




Report to Moderator
 Re: VAO oil filter stick broken tube fix it or plug it in reply to Ted in Sacramento, 04-12-2003 18:16:51  
I have a new housing bought from a Case dealer about 3 years ago.

1. Stem tube is 0.24" OD x 3-3/4"L above press shoulder.
2. Three orifices (measured � 0.002"): one @ verticle top of tube 0.081". 5/16" down from top of tube and 180� apart 2 @ 0.093".

The total area of the 3 orifices exceeds the ID of the tube indicating they are used as directors and the filter media is the restrictor.

[Log in to Reply]  [No Email]
Ted in Sacramento

04-15-2003 14:53:05




Report to Moderator
 Re: Re: VAO oil filter stick broken tube fix it or plug it in reply to Joe (Wa), 04-14-2003 18:56:37  
Thanks I have drilled and fit a .25 in OD tube applied JB Weld and used 5/64 bit to attempt to reproduce the exit orfices, it is interesting though that the exit diameter exceeds the input, I'm not sure the media itself will substantially restrict flow to have an effect on oil pressure, the filter I have from NAPA has a shredded or thread cloth medium, I should be able to tell after I reinstall as my oil pressure was a constant 13 lbs. If I fail my repairs, do you remember what the cost was on a replacement?

[Log in to Reply]  [No Email]
Joe (Wa)

04-15-2003 22:21:33




Report to Moderator
 Re: Re: Re: VAO oil filter stick broken tube fix it or plug it in reply to Ted in Sacramento, 04-15-2003 14:53:05  
Ted, the housing cost about $30. You're fine with what you have now, a new assembly is not going to change anything.

I have 1/4" copper tube in my VAC with top end soldered closed and 2 #44 (0.086") holes 1/4" down from the top.

I have a 311B with same setup using 3/16" brake tubing, but am going to install the new filter hsg to make it "original".

Both tractors have the filter hsg blinded at the block. I can do 2 oil changes for the price of one filter and the way I run them this is best for the engines.

13 psi is adequate for your engine but a constant reading at all rpm & temp is a concern. The relief valve is probably the limiting factor. If it were mine, I would check the gauge against a new 0-30 psi gauge. If the gauge is ok, follow up per MJ's post.

Correct NAPA filter is #1104.

[Log in to Reply]  [No Email]
Ted in Sacramento

04-16-2003 22:05:18




Report to Moderator
 Re: Re: Re: Re: VAO oil filter stick broken tube fix it or plug it in reply to Joe (Wa), 04-15-2003 22:21:33  
I have the NAPA 1104, going to put it on this weekend, as repairs on the filter housing are done. Drove a lot of old Fords in my day 8lbs at idle 25 lbs if lucky at speed and I have thought about the consistent oil pressure, did check the rocker arm for lubrication, seems OK. Will probably pull the pan cause its the right thing to do, clean it and have a look around. I am convinced that changing oil is the answer and relying on this filter system is truly the pay me later. Thanks for the input I still wanted the filter on cause thats the way it came.

[Log in to Reply]  [No Email]
C. Amick

04-14-2003 14:31:31




Report to Moderator
 Re: VAO oil filter stick broken tube fix it or plug it in reply to Ted in Sacramento, 04-12-2003 18:16:51  
Find someone who has a VA or VAC or VAO that you can look at to get the dimensions and hole sizes. I made one for my tractor from a piece of copper tubing. I had to hammer the upper end and sand it to get the proper taper and hole size.



[Log in to Reply]  [No Email]
DKase

04-13-2003 09:18:14




Report to Moderator
 Re: VAO oil filter stick broken tube fix it or plug it in reply to Ted in Sacramento, 04-12-2003 18:16:51  
Check with the filter system on an old Wisconson V4 engine, or an Allis W series. I think they are the same filter system.



[Log in to Reply]  [No Email]
Mike from Canada

04-13-2003 06:04:19




Report to Moderator
 Re: VAO oil filter stick broken tube fix it or plug it in reply to Ted in Sacramento, 04-12-2003 18:16:51  
any filtration is good. the filter housing was usually eliminated when using the magneto w/ a spacer or the hydraulic pump. the filter housing wouldnt fit because the mag assembly was too long.

if you can fix the tube thats good but be careful not to block the passage within the tube. the oil will never reach the filter. you may find yourself having to buy another housing because the tube is too thin to repair.

good luck!

mike

[Log in to Reply]  [No Email]
Ted in Sacramento

04-13-2003 11:14:14




Report to Moderator
 Re: Re: VAO oil filter stick broken tube fix it or plug it in reply to Mike from Canada, 04-13-2003 06:04:19  
When I pulled the old filter the tube was not there, so it had gone bye-bye sometime during the last fifty-five years. As I am not working this tractor, I can afford the $5 to change the oil often in terms of hours operated, with the stuff that flew out the exhaust when it started I'll change a few times in the first hours. One point in the archives made sense forget the $8 for the filter and change the oil twice as often. Also I'm tempted to plug it and see if oil pressure goes up a couple pounds which might prove more valuable than the partial filtering. I guess my reasoning if I fix it would be, if the filter works at a twenty percent rate change the filter every five oil changes? Seems like the filter was an enginerring afterthought. Thanks for your interest. Ted

[Log in to Reply]  [No Email]
Mike from Canada

04-13-2003 14:01:35




Report to Moderator
 Re: Re: Re: VAO oil filter stick broken tube fix it or plug it in reply to Ted in Sacramento, 04-13-2003 11:14:14  
most tractors built worked on an oil bypass filtration system so that when the oil was too cold it would still get to all of its predetermined areas w/o being caught up in the filter until the temp. came up and flow improved.

mj has a good idea. just remember to crimp the end of the tube that goes inside the filter and drill a tiny hole right through perpendicular near the end so the oil can pass through and into the filter media. it'll save you dropping the oil pan.

good luck!

mike

[Log in to Reply]  [No Email]
Ted in Sacramento

04-13-2003 17:11:14




Report to Moderator
 Re: Re: Re: Re: VAO oil filter stick broken tube fix it or plug it in reply to Mike from Canada, 04-13-2003 14:01:35  
Got distracted from my filter purpose, A Canadian won the Masters, Oh No, sorry Mike or rather happy for you Mike, will never surpass the Great One tho. Back to the question; does the oil tube come originally (factory) plugged at the top with side orfices or does it originally vent out the top? Reason my pressure is not really a question it is 13 psi without a tube connected, venting straight under filter no restriction.

[Log in to Reply]  [No Email]
Mike from Canada

04-13-2003 17:35:29




Report to Moderator
 Re: Re: Re: Re: Re: VAO oil filter stick broken tube fix it or plug it in reply to Ted in Sacramento, 04-13-2003 17:11:14  
yeah that mike weir is great. if i had an appreciation for golf id probably enjoy it more. you see... if you take the ball out of the equation, all youre doing is walking and theres nothing much exciting about that.

but i digress...

yes... the tube was plugged but rounded @ the top that might be a little hard to duplicate w/ a copper tube but you can try shaping it.

and yes the tube had holes right through it at the top so the oil could pass through the filter media to the bottom to be put through the engine.

hope that helps!

mike

[Log in to Reply]  [No Email]
Ted in Sacramento

04-13-2003 19:15:05




Report to Moderator
 Re: Re: Re: Re: Re: Re: VAO oil filter stick broken tube fix it or plug it in reply to Mike from Canada, 04-13-2003 17:35:29  
I believe I will, if only for the sake of authenticity, repair the filter tube, it can't hurt to have some filtering, and it sounds like the flow through the tube had restriction which may boost pressure and improve my upper end oiling performance. Pinching/plugging the top not a problem, how many holes? What approximate diameter? if you can recall. Thanks

Don't remember who said it but it was something like Golf is a good walk spoiled.

[Log in to Reply]  [No Email]
Mike from Canada

04-14-2003 08:26:39




Report to Moderator
 Re: Re: Re: Re: Re: Re: Re: VAO oil filter stick broken tube fix it or plug it in reply to Ted in Sacramento, 04-13-2003 19:15:05  
dont worry about the authenticity that much, i dont know any show judge that will tear down the engine to check and see you're using wiseco race pistons in your tractor let alone a homemade oil tube. farmers did what they want when they want and that ads a unique quality to the appearance and performance of individual tractors.

as for the holes, there are just 2. and im not sure about the size but theyre like 1/64" or something. CASEPOWER might know. start another post.

hope this helps!

mike

[Log in to Reply]  [No Email]
mj

04-13-2003 12:32:10




Report to Moderator
 Re: Re: Re: VAO oil filter stick broken tube fix it or plug it in reply to Ted in Sacramento, 04-13-2003 11:14:14  
These engines are rated for 12-20 psi oil pressure...you're OK there....next time you have the oil pan off stretch the oil pump bypass spring until it relaxes to 1 15/16" (spec.) or 2" (err to high side) and you'll probably see 16 - 20 psi with no other changes. I've replaced missing oil filter tubes with copper or brass tubing of a size that fits tight after the end has been filed or turned down to a light interference fit....tap into place.

[Log in to Reply]  [No Email]
Ted in Sacramento

04-13-2003 17:18:11




Report to Moderator
 Re: Re: Re: Re: VAO oil filter stick broken tube fix it or plug it in reply to mj, 04-13-2003 12:32:10  
Actually if the gaskets are available I wouldn't mind having a look down there, cleaning the pan would be worth the time to unbolt and a look at the bypass spring is added incentive. Thanks for the tip.



[Log in to Reply]  [No Email]
mj

04-14-2003 07:19:56




Report to Moderator
 Re: Re: Re: Re: Re: VAO oil filter stick broken tube fix it or plug it in reply to Ted in Sacramento, 04-13-2003 17:18:11  
You can get pan gaskets from NAPA, CarQuest, and American Auto Parts stores and I'm sure there are others. As for the bypass spring...the last one I did I stretched it and added a couple of .010 thick washers to boot...that VAO runs 16 lbs. at idle and right at 20 at max. governed engine speed. By the way, when you buy a gasket ask if they have them in full neoprene...they cost more initially but can be reused over and over. :-)

[Log in to Reply]  [No Email]
mj

04-14-2003 07:26:41




Report to Moderator
 Re: Re: Re: Re: Re: Re: VAO oil filter stick broken tube fix it or plug it in reply to mj, 04-14-2003 07:19:56  
RE-Used...Over and Over....is that redundant or what? I really NEED some sleep!



[Log in to Reply]  [No Email]
[Options]  [Printer Friendly]  [Posting Help]  [Return to Forum]   [Log in to Reply]

Hop to:


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Copyright © 1997-2023 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy