Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver

Attention Forum Users: On the 28th of December 2023 at 9:00am Central Time, we will be taking the forums down for maintenance while we prepare the new forums for your use. Please click here for more information.

Discussion Forum
:

Conflicting posts

Welcome Guest, Log in or Register
Author 
Shane

02-04-2003 15:34:06




Report to Moderator

I've read many posts in here and in other forums that keep conflicting with each other. One person says that the Case tractors were fuel thirsty and the powershift's are expensive and unreliable. The next guy says the exact opposite. We use all Case tractors and are very pleased, even with the powershifts, only one went bad. And I couldn't tell you about the fuel economy, never used another brand, other than the Ford we demonstrated several years ago. I know it is way more economic then the older Cases or any older tractor for that matter. So what is your opinion of these old Cases, Refering to the 70, 90, and 94 series. By the way, I had posted earlier on straight piped tractors and all of ours have cabs so the extra exhaust noise doesn't hurt the ears.

[Log in to Reply]   [No Email]
Pat

02-08-2003 14:00:10




Report to Moderator
 Re: Conflicting posts in reply to Shane, 02-04-2003 15:34:06  
I have worked at an JD equipment dealer for three years and go home and help my uncle farm at night. My uncle has a JD4430, a JD4020 and an old 970 Case. The JD4020 resides at our shop because it just keeps breaking down. They were supposed to be the best tractor out their, what a crock. I see those 4020's come in all the time for Hyd problems that never can be fixed. John Deere close-minded-hydrolics, small clutch disks and syncro-grind transmision. I cant believe they were ever a good tractor. Our 4430 is an ok tractor but it to is showing signs of hyd problems. But that damn old 970 just keeps going like the energizer bunny. Over 7800hrs and it has never left the farm. It pulls a 14 ft diskbine, slinger spreader, ag-bagger, 18 disk harrow, and 4-16 spring reset plows, round baling you name it, it does it. NO QUESTIONS ASKED! Something a 4020 can't live up to! Our 970 is factory orginal. Keep you JunkDeeres I'll keep buying Cases. I have a vac,vai,830,930,1030,1070. Good stuff.

[Log in to Reply]  [No Email]
Jrred

02-06-2003 07:30:20




Report to Moderator
 Re: Conflicting posts in reply to Shane, 02-04-2003 15:34:06  
I have owned a lot of diferent tractors and worked them hard! as far as fuel cunsumtion our 1070 was the best working hard on a pto water pump it would use 3 gallons per hour. The 966 IH would use 4.5, Oliver 1855 5, case 1030 5, JD 4020 11. My neibhor has a JD power unit on his pump and he said it uses 12 gal per hour and he thought that was pretty good. I didn't have the heart to tell him what my 1070 was getting!

[Log in to Reply]  [No Email]
case poor in pa

02-05-2003 18:09:41




Report to Moderator
 Re: Conflicting posts in reply to Shane, 02-04-2003 15:34:06  
i dont know much about them new fangled series cases.. but my 730 gas can slurp down 2 gallons a hour pullin a 10 foot disc thru plowed sod in 4 th gear with the hammer down lappin a 5000 ford diesel evry round an



[Log in to Reply]  [No Email]
Shane

02-06-2003 05:11:01




Report to Moderator
 Re: Re: Conflicting posts in reply to case poor in pa, 02-05-2003 18:09:41  
That sounds like a really thirsty tractor but it is a gas so it might not be. If it were a diesel only pullin a 10 footer and using that much fuel I would put her out to pasture!



[Log in to Reply]  [No Email]
Steven@nd

02-05-2003 16:21:14




Report to Moderator
 Re: Conflicting posts in reply to Shane, 02-04-2003 15:34:06  
We have a 2590 and love it! As for the fuel economy it looks like a hog compared to our other tractors. We have a 1086 with saddle tanks that will run a long day on a tank of fuel, whereas the Case only has the rear tank and needs fuel before dinner time. Also we are talking 150 hp vs 210 hp.

As for the powershift, the JD ps from that era jumps ALOT more! Neighbors have more problems with their JD tractors, they just haul them in when it is dark outside. Ours has 5500 hours on it and is still like new, doesn't burn a drop of oil and the tranny shifts great.

People who have problems with them stomp on the clutch when the ps is in 2nd or 3rd gear. You absolutely MUST shift to 1st before clutching!

[Log in to Reply]  [No Email]
Jeb Mccranie

02-06-2003 09:38:11




Report to Moderator
 Re: Re: Conflicting posts in reply to Steven@nd, 02-05-2003 16:21:14  
My 2590 gets pretty good fuel economy but I have to fill it up before lunch. My 1290 gets pretty poor fuel economy but has a lot of power.



[Log in to Reply]  [No Email]
Shane

02-06-2003 05:18:55




Report to Moderator
 Re: Re: Conflicting posts in reply to Steven@nd, 02-05-2003 16:21:14  
You have to fill the 2590 with fuel by lunch?! What in the world are you pulling? I believe they hold 80 gallons or more, you must really run that Case like a race car, wide open! Thank god you are using a Case, the other brands wouldn't handle that kind of work.



[Log in to Reply]  [No Email]
Larry in AB

02-05-2003 17:40:55




Report to Moderator
 Re: Re: Conflicting posts in reply to Steven@nd, 02-05-2003 16:21:14  
Also whats not good is when you're crusin on the highway in 4th wide open throttle and start shifting the powershift down or push the clutch in.



[Log in to Reply]  [No Email]
Shane

02-06-2003 05:15:07




Report to Moderator
 Re: Re: Re: Conflicting posts in reply to Larry in AB, 02-05-2003 17:40:55  
We always use the clutch while the powershift is in 2nd or 3rd for planting, hasn't cause a problem yet. Never do it in 4th, always idle it down then hit the clutch, still in 4th 3rd. Seems to not harm them as long as the units are properly adjusted.



[Log in to Reply]  [No Email]
Casedude

02-06-2003 20:41:26




Report to Moderator
 Re: Re: Re: Re: Conflicting posts in reply to Shane, 02-06-2003 05:15:07  
If you use the clutch to down shift the power shift you should do it one at a time. Because if you down shift all at once with the power shift it will brake\twist the shaft in the tranny. thats what happend to ours when we got it. someone Downshifted with a heavy load going to fast or downshifted to fast and twisted the shaft.



[Log in to Reply]  [No Email]
Jim P

02-06-2003 22:17:47




Report to Moderator
 Re: Re: Re: Re: Re: Conflicting posts in reply to Casedude, 02-06-2003 20:41:26  
What a lousy design, make it to shift back to first when the clutch is pushed in. and than tell you not to do it as it will trash things. I try to always shift down first but in a emerency stop(and you will always have them) you can't. Also the mech. told me to always use the Diff. lock at all times because not using it wears out the pinions. Again a lousy way to cover for a poor design. If you run your 4690 like a 2390 and your 2590 like a 2290 and your 2390 like a 2090 you can have purty good luck . Pull them at rated hp and watch the bills pile up.

[Log in to Reply]  [No Email]
Shane

02-07-2003 05:05:31




Report to Moderator
 Re: Re: Re: Re: Re: Re: Conflicting posts in reply to Jim P, 02-06-2003 22:17:47  
As I said before, we step on the inching pedal all the time planting and round baling. Run in 3rd 2nd and 3rd 3rd respectively and never twisted a shaft or caused any other problems. That inching pedal gets pushed all the way down at least a hundred times a day while baling and probably the same while planting. So this is why I call these posts conflicting. You guys tell me NOT to work the powershift like I have for years or it WILL break but I haven't had any problems yet. Thanks for the posts.

[Log in to Reply]  [No Email]
Larry in AB

02-07-2003 07:11:29




Report to Moderator
 Re: Re: Re: Re: Re: Re: Re: Conflicting posts in reply to Shane, 02-07-2003 05:05:31  
I think where care has to be taken is when traveling fast down a road especailly payment pulling a load then stepping on the pedal or downshifting the powershift with the throttle wide open. Really its common sense I wouldn't do it with any machine be it Case or not.

In the field we push the pedal to the floor too since they were new.



[Log in to Reply]  [No Email]
Larry in Ab

02-05-2003 10:01:33




Report to Moderator
 Re: Conflicting posts in reply to Shane, 02-04-2003 15:34:06  
I still have our 1974 970 and its one of the main haying tractors. Any tractor that lasts 29 years is a good machine. Engine is orginal, A/C works great and is original, ps trans was removed once by me 5 years ago to reseal. Clutches, gears etc. were still fine, had the dealer look at the parts and he said you must take care of it. He was saying with them old Case powershifts farmers would get a new hired hand and they would unknowningly screw them up. Also as poweshifts go Case is one of the easiest to repair not much to them just split the tractor and pull it out the front.

Same as pto clutch no need to split the tractor it comes out the back. The batteries are in a hard spot to get at also the hood was harder to get off. The 90 series made improvements with the batteries, hydraulics and hood set ups. Plus the cab was much quieter. Actually it was probably the quietest cab of that era. I've seen cab noise level figures and a 2090 is or is damn near as quiet as a tractor 20 years newer.

I been asked when I'm going to update a tractor as the 970 is 29 years old! What for it works great for the jobs asked of it still. Parts or no problem plus lots of used available. I may give it a paint job pretty soon though.

[Log in to Reply]  [No Email]
Jeb Mccranie

02-06-2003 09:41:41




Report to Moderator
 Re: Re: Conflicting posts in reply to Larry in Ab, 02-05-2003 10:01:33  
I had to replace the clutch im my 1290 last year because of my rotory mower burning it out.



[Log in to Reply]  [No Email]
Jeb Mccranie

02-06-2003 09:41:40




Report to Moderator
 Re: Re: Conflicting posts in reply to Larry in Ab, 02-05-2003 10:01:33  
I had to replace the clutch im my 1290 last year because of my rotory mower burning it out.



[Log in to Reply]  [No Email]
Dermottj

03-12-2006 14:59:22




Report to Moderator
 Re: Re: Re: Conflicting posts in reply to Jeb Mccranie, 02-06-2003 09:41:40  
Hi, I have been reading through the Yesterday"s Tractor forum and noticed that you have posted that you had to replace the clutch on your 1290 Case Tractor. My father in law is about to have to do the same, did you do it yourself? If so, did you have to take the cabin off or is there another way?

I look forward to your response,

Regards

John



[Log in to Reply]  [No Email]
Shane

02-05-2003 13:17:55




Report to Moderator
 Re: Re: Conflicting posts in reply to Larry in Ab, 02-05-2003 10:01:33  
I have solved the problem of the batteries being under the cab floor by removing the box and making a bracket to mount it beside the engine. There are several bolt holes you can use. And as far as the pto clutches, that is very nice to be able to pull them out the back. We have replaced the clutches in all 3 of the 1070's we have. We run a 12 foot New Holland DiscBine and think that is what caused the clutches to fail. Started using the 1270's to run it, besides, you can run faster with the extra horse power. Wish the hoods tilted like the 90 series but have to love those 70's.

[Log in to Reply]  [No Email]
Larry in AB

02-05-2003 17:48:29




Report to Moderator
 Re: Re: Re: Conflicting posts in reply to Shane, 02-05-2003 13:17:55  
I've only done our old 970 clutch once in 29 years most of which has been running the pto. Alot had to do with a rough mower we once had with a siezed clutch. The 2090 pto clutch is still original.

Reminds me about the batteries the first set in the 970 lasted us 14 years. I have had the starter off over the years and replaced the drive and put some brushes in it.

How many horse is a 1270? I've been told more than once the old 1275 (if its the one with a standard trans) was a really good pulling tractor.

[Log in to Reply]  [No Email]
Shane

02-06-2003 05:08:48




Report to Moderator
 Re: Re: Re: Re: Conflicting posts in reply to Larry in AB, 02-05-2003 17:48:29  
The 1270's were two different horse power ratings. The early ones were 127 and the later ones were 135. I think those numbers are correct. It is the turbo that makes the torque over a broader range and way more power than the 1070. As far as a 1275, never heard of one or even a 1270 with the standard tranny.



[Log in to Reply]  [No Email]
Larry in AB

02-06-2003 07:38:12




Report to Moderator
 Re: Re: Re: Re: Re: Conflicting posts in reply to Shane, 02-06-2003 05:08:48  
My mistake its a 1175 that I'm talking about at around 120 hp with the standard 8 speed trans. It also had a different rear axle set up. Maybe someone else knows the details as I can't remember them anymore.



[Log in to Reply]  [No Email]
Big Orange

02-06-2003 10:36:06




Report to Moderator
 Re: Re: Re: Re: Re: Re: Conflicting posts in reply to Larry in AB, 02-06-2003 07:38:12  
An 1170&1175 were similar 8speeds with outboard planetaries.Have an 1170 Rated@121 from the factory set to 1270 specs 180 horse,no problems ,about 4.5 gallons/hr.



[Log in to Reply]  [No Email]
Shane

02-06-2003 11:28:53




Report to Moderator
 Re: Re: Re: Re: Re: Re: Re: Conflicting posts in reply to Big Orange, 02-06-2003 10:36:06  
The 1270 didn't make 180 out of the factory, the 1570 did.



[Log in to Reply]  [No Email]
Big Orange

02-06-2003 15:20:40




Report to Moderator
 Re: Re: Re: Re: Re: Re: Re: Re: Conflicting posts in reply to Shane, 02-06-2003 11:28:53  
Set to 1270 specs, my 1170 turned 182 hp. on the dyno whether it was supposed to or not.My 2390 turned 188 on the same dyno.



[Log in to Reply]  [No Email]
Casedude

02-06-2003 20:44:56




Report to Moderator
 Re: Re: Re: Re: Re: Re: Re: Re: Re: Conflicting posts in reply to Big Orange, 02-06-2003 15:20:40  
My uncles 1570 was pushing 210 stock. and our 1070 is pushin 145 with turbo and pump turned. and all case's were underrated too. 1070 supposed to have 110 factory



[Log in to Reply]  [No Email]
Jim P

02-06-2003 22:23:19




Report to Moderator
 Re: Re: Re: Re: Re: Re: Re: Re: Re: Re: Conflicting posts in reply to Casedude, 02-06-2003 20:44:56  
Again I say pull them at that hp and I'm glad you will have to pay the bills. I think they overrated all case tractor after the LA. The LA was underrated.



[Log in to Reply]  [No Email]
Big Orange

02-07-2003 05:18:01




Report to Moderator
 Re: Re: Re: Re: Re: Re: Re: Re: Re: Re: Re: Conflicting posts in reply to Jim P, 02-06-2003 22:23:19  
What bills are they?Never had problems with my powershiftand I use it hard,but I'm an operator note just a driver.



[Log in to Reply]  [No Email]
Shane

02-07-2003 08:43:15




Report to Moderator
 Re: Re: Re: Re: Re: Re: Re: Re: Re: Re: Re: Re: Conflicting posts in reply to Big Orange, 02-07-2003 05:18:01  
I have only had a few repairs in relation to the number of hard hours put on our Cases. I think ole Jim must be a Deere fan or something.



[Log in to Reply]  [No Email]
Jim P

02-07-2003 21:41:26




Report to Moderator
 Re: Re: Re: Re: Re: Re: Re: Re: Re: Re: Re: Re: Re: Conflicting posts in reply to Shane, 02-07-2003 08:43:15  
No JD fan but I do think some models were good. I have owned these model cases, 1929 L(still have) 1947 VAI,1947 LA gas, 1948 La LP, 1949 LA LP,1956 600 LP, 1958 900 LP(still have),1960 930 LP, 1966 930CK Diesel(still have), 1972 1470, 1979 2390(still have), 1980 4690(still have) 1982 2590(still have) and one JD a 1982 410 backhoe(still have).



[Log in to Reply]  [No Email]
Casedude

02-07-2003 20:29:09




Report to Moderator
 Re: Re: Re: Re: Re: Re: Re: Re: Re: Re: Re: Re: Re: Conflicting posts in reply to Shane, 02-07-2003 08:43:15  
when we got the tractor motor was stuck rearend housing cracked and powershift junk replaced the powershift clutches and housing. NEVER touched the engine. just got it unstuck never reringed it or any thing. And it was pushin 145 hp. and we have worked it hard and we still haven't had a problem and we got the tractor around in the late 70s early 80s. And its been a good tractor we don't use it as much because we cash rent our farm now. But use it every now and then.

[Log in to Reply]  [No Email]
Shane

02-06-2003 08:41:12




Report to Moderator
 Re: Re: Re: Re: Re: Re: Conflicting posts in reply to Larry in AB, 02-06-2003 07:38:12  
Yes, the 1175 was different than the 1070's, I think they were closer to the 12,13,and 15's. As far as the rearends and such. I have never seen a Case 70 with the standard tranny myself, am sure I would much rather have the powershift, now if it only had one more gear!



[Log in to Reply]  [No Email]
howard s.

02-05-2003 08:22:48




Report to Moderator
 Re: Conflicting posts in reply to Shane, 02-04-2003 15:34:06  
I would not want to go back to straight gears, but I personally do not care for full powershift transmissions for several reasons. First, they do cost more to buy and operate, I don't care what anybody says about that. I have owned JD 4640 and 4840 with PS, and you can literally feel the difference from a 4640 with a quad range tranny.(4840 only came with PS). Figure a good ten per cent of engine HP to operate the PS. Secondly, you couldn't shift the damn things into reverse very well at all. Loader tractors they weren't. I'm not bashing JD here, I have a 4430 with QR that I love. The benefit of PS over a tranny that you can clutch and shift without grinding is marginal at best. Regards, howard s.

[Log in to Reply]  [No Email]
Shane

02-05-2003 13:22:45




Report to Moderator
 Re: Re: Conflicting posts in reply to howard s., 02-05-2003 08:22:48  
I wouldn't use a gear tranny either except we have an 830 for the auger which is gear drive. As far as a full powershift, we used to have an AC 7045 with the powershift, believe it had 12 gears. Was nice and all but the tractor itself is a useless wonder and the cab made anyone feel cramped up. I would like to see more shiftable gears in a setup like the older Cases had, that would be ideal for me.

[Log in to Reply]  [No Email]
Larry in AB

02-05-2003 17:56:51




Report to Moderator
 Re: Re: Re: Conflicting posts in reply to Shane, 02-05-2003 13:22:45  
Some times I wish it had a 4 speed powershift for square baling at times. But for the most part the 3 speed does fine, beats the heck out of grinding gears. Mine shift nice under load pulling but when under no load like haying they are jerky. A old Case mechanic told me one time no problem if the tractor is used just for haying he's adjusted them to shift nice and smooth. Might not be good though for pulling heavy when you need the hard fast shift.

[Log in to Reply]  [No Email]
indiana farmer

02-05-2003 03:22:55




Report to Moderator
 Re: Conflicting posts in reply to Shane, 02-04-2003 15:34:06  
i'm farly new to this site, so i'll put my few cents in. dad always said if case co. had showed their dealers how to operate the case-o-matic trans. and the dealer would show the farmer how to run them, then they would have liked them better. the same thing is true with the power shift trans. our dealer showed us how and how not to run them. we never had any trouble with 70,90,94 series. people said the p.s. trans. jumped and jerked, but i've drove other makes they act the same way.

[Log in to Reply]  [No Email]
Max

02-04-2003 20:47:39




Report to Moderator
 Re: Conflicting posts in reply to Shane, 02-04-2003 15:34:06  
Good observation. Here's another one that I found interesting. When a Case 1570 or 2590 broke a rear axle, it was considered junk but when a JD 4630 or 4640 broke an axle the owner had to much weight on it and that caused the break. There's even more concerning clutches, rear end etc but it would take a long time to discuss. This was based on working at a Case company store in the midwest and a Large John Deere dealer in CA. The one big disparity that had me really confused was when I was in the midwest I was working under flat rate and the store charge $26 hr and I would overhaul a 504 in a 1450 crawler in 40 hours for around $5000. THen I moved out west and would do the same kind of overhaul on a 466 Deere and the customer was charged $10000. The suprising thing was that I put in the same 40 hours to complete the job but the dealer had a shop rate of $28 hr. I guess thats one of the reasons I'm so Pro-Case. As far as the engines and power shifts went, the engines were pretty economical from what I saw and the powershifts were as good as they were treated, inother words, abuse them, expect to work on them alot.

[Log in to Reply]  [No Email]
[Options]  [Printer Friendly]  [Posting Help]  [Return to Forum]   [Log in to Reply]

Hop to:


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Copyright © 1997-2023 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy