Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver

Attention Forum Users: On the 28th of December 2023 at 9:00am Central Time, we will be taking the forums down for maintenance while we prepare the new forums for your use. Please click here for more information.

Case Tractors Discussion Forum
:

Anyone have a picture of a VAC hand crank?

Welcome Guest, Log in or Register
Author 
ff316

09-20-2006 08:10:19




Report to Moderator

I would like to have one but I can"t honestly say I"ve ever seen one. Can someone post or email a pic to me? Thanks!

Ernie in KY




[Log in to Reply]   [No Email]
C. Amick

09-20-2006 10:05:14




Report to Moderator
 Re: Anyone have a picture of a VAC hand crank? in reply to ff316, 09-20-2006 08:10:19  
Here's a photo of one that is up for auction on Ebay. Click on link below.



[Log in to Reply]  [No Email]
ff316

09-20-2006 13:53:45




Report to Moderator
 Re: Anyone have a picture of a VAC hand crank? in reply to C. Amick, 09-20-2006 10:05:14  
Is this for a VAC? I've been watching ebay but I want to make sure it's the right thing.

[img]http://i8.ebayimg.com/02/i/08/68/71/94_12.JPG[/img]



[Log in to Reply]  [No Email]
ff316

09-20-2006 13:58:48




Report to Moderator
 Re: Anyone have a picture of a VAC hand crank? in reply to ff316, 09-20-2006 13:53:45  
third party image

Trying again



[Log in to Reply]  [No Email]
JR-KY

09-20-2006 09:52:10




Report to Moderator
 Re: Anyone have a picture of a VAC hand crank? in reply to ff316, 09-20-2006 08:10:19  
third party image

ERNIE, we have 1 or 2 ..look me up at a show and will show you ..



[Log in to Reply]  [No Email]
amo

09-20-2006 09:43:39




Report to Moderator
 Re: Anyone have a picture of a VAC hand crank? in reply to ff316, 09-20-2006 08:10:19  
AT ONE TIME THEIR WAS ONE ON E-BAY, IT HAS A LONG SHAFT ABOUT 12-18 INCHES 90 DEGREE BENT DOWN ABOUT 10 INCES ANOTHER 90 DEGREE BEND OUT 6-8 INCHES. I BUILT ONE OUT OF A 3/4 STEEL ROD. ORED HOLE AND PUT BOLT THRU END TO ENGAGE IN ENGINE AND HEATED TO MAKE BENDS. ROD COST ABOUT $8.00 GOOD LUCK AND IT WORKS GREAT



[Log in to Reply]  [No Email]
[Options]  [Printer Friendly]  [Posting Help]  [Return to Forum]   [Log in to Reply]

Hop to:


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Copyright © 1997-2023 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy