TRACTOR PARTS Allis Chalmers Case & David Brown Farmall & International Ferguson Ford & New Holland John Deere Massey Ferguson Massey Harris Minneapolis Moline Oliver & Cockshutt Kubota / Yanmar

TRACTOR MANUALS

Allis Chalmers	Case	Farmall IH	Ford 8N,9N,2N	Ford
Ferguson	John Deere	Massey Ferguson	Minn. Moline	Oliver

Attention Forum Users: On the 28th of December 2023 at 9:00am Central Time, we will be taking the forums down for maintenance while we prepare the new forums for your use. Please click here for more information.

Case Tractors Discussion Forum

CASE D motor specs.

Welcome Guest, Log in or Register

Author

Brian Tousignan

08-30-2007 17:25:08

Report to Moderator

We just purchased what I believe to be a 1940 (?) Case Model D. I'm interested in trying to find some of the motor specifications. Also, any info. for sources for parts, etc. would be helpful as this is the first case we have bought.

Would the Desert Sand/Flambeau Red be the correct color scheme for this model/year? Would this have been a six or twelve volt system? Live PTO? Three speed plus reverse?

Sorry so many questions! Thanks for any help.

[Log in to Reply] [No Email]

noncompos

08-31-2007 17:13:51

Report to Moderator

Re: CASE D motor specs. in reply to Brian Tousignant, 08-30-2007 17:25:08

If you need immediate info, your local library should have a file of Motor's Truck and Tractor manuals; my 50 issue covers D's to 49, and you can usually xerox pages if you need to take info home until a real manual comes. HTH.

[Log in to Reply] [No Email]

C. Amick

08-31-2007 09:16:19

Report to Moderator

Re: CASE D motor specs. in reply to Brian Tousignant, 08-30-2007 17:25:08

Yesterday's Tractors sells a service manual for it on this web site. Click on Tractor Manuals under Marketplace.

[Log in to Reply] [No Email]

Gene Dotson

08-30-2007 19:38:30

Report to Moderator

Re: CASE D motor specs. in reply to Brian Tousignant, 08-30-2007 17:25:08

Brian;

1940 D would be all Flambeau red with accessories painted black to your taste.

Electrical system was originally 6 volt with negative ground. Does not have live pto and early models were 3 speed and later were 4 speed. If the tractor was originally shipped on steel wheels, 4th gear will be locked out if a 4 speed.

Where are you located? There are members on this board who can help with many parts. Jonh Saeli in New York, Don Livingston in Minnesota, Dave Reed in Maryland and Joe Peeper in Oklahoma, just to name a few... Gene

[Log in to Reply] [No Email]

rustywrench1

08-30-2007 19:37:13

Report to Moderator

Re: CASE D motor specs. in reply to Brian Tousignant, 08-30-2007 17:25:08

I believe Paint would be Flambeau Red only, with six-volt system, three forward speeds one reverse. Good luck...

[Log in to Reply] [No Email]

rustywrench1

08-30-2007 19:26:11

Report to Moderator

Re: CASE D motor specs. in reply to Brian Tousignant, 08-30-2007 17:25:08

If it still has the serial number plate on the dash take the first two digits and subtract 4 this will give you the year. you're 1940 tractor serial number would start with 44*****. Check E-BAY for owners manual you will need one.

[Log in to Reply] [No Email]

brian tousignant

08-31-2007 17:15:45

Report to Moderator

Re: CASE D motor specs. in reply to rustywrench1, 08-30-2007 19:26:11

Thanks for the reply! As someone who has 4 John Deere(s) & an Allis-Chalmers, I'm a little embarrassed about how little I know about this Case.

First, based on your reply I re-checked the serial# which seemed to be a digit short, and after a little scratching realized I missed the leading digit, which was a (5). So the entire number is 5413797D. I guess that makes it a 1950 model?

I knew the motor was setup when we bought it, but what I didn't know was that some of the valve cover bolts, the valve tappit bolts, and the push-rods were all MIA! I have looked at the crank which seem to look good. Is my best option to disconnect and drive pistons up through the top or is there a secret to loosening it up?? We were able to free up our Allis after some soaking and trying some different ways to move the pistons.

Does this change your thoughts on some of the other questions?? I'm located in the far Northeast corner of NYS, 15 miles from VT & Canadian border(s).

Thanks for any suggestions!!

Brian T.

[Log in to Reply] [No Email]

[Options] [Printer Friendly] [Posting Help] [Return to Forum] [Log in to Reply]

TRACTOR PARTS	TRACTOR MANUALS

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home | Forums

Copyright © 1997-2023 Yesterday's Tractor Co.
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy