Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver

Attention Forum Users: On the 28th of December 2023 at 9:00am Central Time, we will be taking the forums down for maintenance while we prepare the new forums for your use. Please click here for more information.

Case Tractors Discussion Forum
:

Torque Tube (pic) Question-VAI

Welcome Guest, Log in or Register
Author 
Kestrel CT

04-02-2007 18:02:08




Report to Moderator

third party image

Before I refill the tranny with 7 gal. of 90 wt. tomorrow, I thought I was being a good owner and checked the torque tube hydraulic filter, even though I have no hydraulics installed.

Well, it came out in pieces like an old dirty slinky and there was hardly any oil in its 2 gallon reservoir.

My question is; do I even need a filter given no hydraulic pumps?

Secondly, was I darn lucky the drive shaft and bearings in the torque tube didn't seize due to lack of oil ?

The tractor ran fine before I "discovered" the missing fluid.

I assume the two housing reservoirs (tube and tranny) are separated by seals and the fluids shouldn't comingle.

Maybe my seals were bad and ironically this allowed enough leakage into the the torque tube to keep the components happy.
As always, any feed back appreciated.

[Log in to Reply]   [No Email]
630crazy

04-03-2007 14:46:00




Report to Moderator
 Re: Torque Tube (pic) Question-VAI in reply to Kestrel CT, 04-02-2007 18:02:08  
My dad ran hydraulic fluid in torque tube and transmission in our 630 for years before selling to my uncle. To my knowledge it's still that same way today and it's been at least 30-35 years now. The bad part is the axle and pto seals leak, guess the hydraulic fluid is a little to thin for the seals.

Besides the 730, 830, 930 and 1030 all used hydraulic in the tranny and final drive.



[Log in to Reply]  [No Email]
Joe (Wa)

04-02-2007 19:41:53




Report to Moderator
 Re: Torque Tube (pic) Question-VAI in reply to Kestrel CT, 04-02-2007 18:02:08  
Element was used to filter return line hyd oil, has no function in your situation.

Drive shaft has taper roller bearing, probably didn't hurt it. Belt pulley has bevel gears, may have taken a hit if prolong or severe belt work.

Torque tube & transmission fluids are isolated by the drive shaft seal (double lipseal)in the front of the transmission.

Torque tube oil level is higher than transmission level and leaks from the former to the later if defective drive shaft seal, drive shaft seal retainer gasket or gasket below on counter shaft front bearing cover. Gasket leaks are not likely, shaft seal is generally the leak.

Use SAE 90 in your torque tube, same oil as the transmission. 90 is the factory recommended oil for non-hyd reservior use, satisfactory lube for bearing & pulley gears, less likely to leak (or slower) through a less than perfect drive shaft seal into the transmission.

Joe

[Log in to Reply]  [No Email]
Kestrel CT

04-03-2007 15:09:01




Report to Moderator
 Re: Torque Tube (pic) Question-VAI in reply to Joe (Wa), 04-02-2007 19:41:53  
third party image

Joe, thanks so much for the thorough explanation. I put a fair amount of work in to get to this stage and didn't want to blow it now. Also much appreciated your previous tips this winter.

I filled the torque tube up and the transmission with 90 wt. this afternoon, crossed my fingers and put her in gear. Away she went like a swiss watch; no bumps, grinds, leaks, or other complaints...so far anyway.

Had her split apart all winter and forgot what she looked like. If it warms up ever, I'll paint and install the fenders, maybe even a decal or two.

Next winter maybe I'll get to that leaky rear main engine seal.

Thanks again lending me a hand with my first tear down.

That's Edith in the driver's seat in case your wondering.

[Log in to Reply]  [No Email]
dpski

04-15-2007 19:33:57




Report to Moderator
 Re: Torque Tube (pic) Question-VAI in reply to Kestrel CT, 04-03-2007 15:09:01  
Nice job, looks great.

BTW what size rear tires are on your tractor? I recently purchased a 43 VAI and will be embarking on a restore project and tires are on the list of things to do. Thanks



[Log in to Reply]  [No Email]
Joe (Wa)

04-03-2007 17:02:31




Report to Moderator
 Re: Torque Tube (pic) Question-VAI in reply to Kestrel CT, 04-03-2007 15:09:01  
I'll second olddog, that is a beautiful tractor! Edith looks like she is well pass the tender fryer stage and will probably get away with "whitewashing" your seat.

Joe



[Log in to Reply]  [No Email]
olddog

04-03-2007 16:47:37




Report to Moderator
 Re: Torque Tube (pic) Question-VAI in reply to Kestrel CT, 04-03-2007 15:09:01  
Wow!! Nice job of restoring that VAI!!!

Looks ready for the parade!! Didja find new rubber springs for the seat?

Prolly won't have any trouble with the 90W in torque tube. Check it once in a while. Did'ja flush it any ta get the crud out? Put 'er ta work. Edith looks like she's got the eagle eye out for Oscar the rooster.



[Log in to Reply]  [No Email]
Kestrel CT

04-03-2007 18:02:28




Report to Moderator
 Re: Torque Tube (pic) Question-VAI in reply to olddog, 04-03-2007 16:47:37  
Hey Olddog... thanks for the compliments.

Yes, I did find the rubber springs, from Don Livingston. They fit perfect but the seat needs a little tweaking in the height adjustment area. No big deal though.

Never thought of flushing out the tube, just cleaned it some with a rag on a long screwdriver and closed it back up.

I'm more concerned now with hurting Edith's feelings by putting a eagle decal on the tractor. Might cause her some type of predatory distress...can't have that.

[Log in to Reply]  [No Email]
olddog

04-03-2007 06:14:27




Report to Moderator
 Re: Torque Tube (pic) Question-VAI in reply to Joe (Wa), 04-02-2007 19:41:53  
Joe & Kestral, i'm going just the opposite way. Am going to use the hydraulics and Hy-Tran (or equivalent) in TT reservoir, but how do you feel about going the same fluid in the trans/diff housing; since they usually leak back anyway? Some below 30 degree snow plowing probably in this VAC's future as well as summertime loader work.



[Log in to Reply]  [No Email]
Joe (Wa)

04-03-2007 10:01:12




Report to Moderator
 Re: Torque Tube (pic) Question-VAI in reply to olddog, 04-03-2007 06:14:27  
Olddog, if the drive shaft seal & transmission bearings are in good shape, leakback should be none to insignificant.

Here is a statement from the service manual:

" During extremely cold weather a light weight lubricating oil may be added to thin the lubricant. When weather becomes warm again, transmission must be drained and fresh S.A.E. No. 90 lubricant must be used for refilling."

Personally, I think the transmission would live ok on hyd oil for light service but would increase the probability of external leakage at the differential shafts, axle shafts, and pto shaft seals. That's just my opinion, subject to Murphy's law of course.....

Joe

[Log in to Reply]  [No Email]
olddog

04-03-2007 16:28:31




Report to Moderator
 Re: Torque Tube (pic) Question-VAI in reply to Joe (Wa), 04-03-2007 10:01:12  
JEEPERS, I thought Murphy lived here!!! On my 5 acre ponderosa, I can't even get the thing warmed up to what she's usedta. My useage would be "very light" by any modern farmer's standard. Been hopin' a friend would ask me ta brushhog his 16 acres of swamp, just to give it a workout. Already figgured about the thinner oil leakage on the old seals, but methinks diff, axle, and pto seals can be changed without too much further teardown. Plan on installing a new input shaft seal while torn down. Dunno.....
All the newer tractors use one oil in their belly for hyd and trans/diff with a lot more HP than this lil VAC. Mebbe not an irreversable decision. THX for your input.

[Log in to Reply]  [No Email]
[Options]  [Printer Friendly]  [Posting Help]  [Return to Forum]   [Log in to Reply]

Hop to:


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Copyright © 1997-2023 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy