Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver

Attention Forum Users: On the 28th of December 2023 at 9:00am Central Time, we will be taking the forums down for maintenance while we prepare the new forums for your use. Please click here for more information.

Case Tractors Discussion Forum
:

Paging JGarner and others

Welcome Guest, Log in or Register
Author 
Help Needed on

12-06-2006 20:23:23




Report to Moderator

You guys have been talking about the shift fork problems in earlier posts. Can any of you help me with my 630? My shifter feels like it's not moving anything and my wheels are locked solid.
Here's where I need help. I can't get the blasted cover off the transmission! I can't seem to pry it loose and actually broke a tiny piece of the casting off the corner trying to get a tool under it. Can you guys tell me what might be under there holding it down so tight?

[Log in to Reply]   [No Email]
Help Needed on 630

12-07-2006 10:50:45




Report to Moderator
 Re: Paging JGarner and others in reply to Help Needed on 630, 12-06-2006 20:23:23  
Thanks for the replies.

I still have my cart before the horse.

My cover won't budge, like its welded on.
How do I move the rails if I can't move the cover?

Being as the wheels are locked up, I'll presume I have two rails out of position and stuck in two gears at the same time?

What do you guys think about lifting the back wheels off the ground and try to rock them back and forth in hopes of a shift rail moving or loosening enough to get the cover to move?

Or do I go at it with a block of wood and a maul until something gives?

I hate to think about breaking the cover into pieces to fix this thing, so I'm saving that idea for a last resort. I presume its cast and not steel?

Any ideas would be greatly appreciated.

[Log in to Reply]  [No Email]
JGarner

12-07-2006 12:13:45




Report to Moderator
 Re: Paging JGarner and others in reply to Help Needed on 630, 12-07-2006 10:50:45  
If you have a big (8" plus wide) putty knife, like the kind drywall guys use to spread the mud compound and or about a 2 1/2" - 3" wood chisel, try to wedge it between the cover and trasmission housing. At this point it sounds like the cover has "glued" itself to the housing via the gasket. Try to get the putty knife wedged in by tapping with a hammer. If it seems you are not going to get it slipped in without damaging the knife handle then move to the wood chisel which is made to hammer on. You may be stuck via the gasket material as well. Even if the shift rods are out of alignment you should be able to get the cover to lift up about a 1/2" or so. Keep us informed! We'll get you something figured out yet. If nothing works, e-mail me, I just turned it on. We may need to discuss over the phone to get a better dialog going.

[Log in to Reply]  [No Email]
Help Needed on 630

12-07-2006 15:58:09




Report to Moderator
 Re: Paging JGarner and others in reply to JGarner, 12-07-2006 12:13:45  
JGarner,
Thanks for the ideas.
Tomorrow I'll be in town all day.
Its supposed to warm up this weekend, so I'll wait until then to work on it. I'll have to report back in a few days with my success or failure. Thanks



[Log in to Reply]  [No Email]
Jheitkemper

12-07-2006 08:07:00




Report to Moderator
 Re: Paging JGarner and others in reply to Help Needed on 630, 12-06-2006 20:23:23  
Tough break , Being COG LOCKED ,, I feel your pain ,For over a week now ,I have a Massey 300 combine with a locked up tranny , Guess I will have to get a HUEY helicopter to move it ,,, Wish you the best ,,ALWAYS remember that someone built it ,Therefore SOMEONE ,,Meaning US ,,can fix it againn ,,PATIENCE,,and PERSEVERENCE,,, Blessings ,JIm



[Log in to Reply]  [No Email]
JGarner

12-07-2006 06:15:03




Report to Moderator
 Re: Paging JGarner and others in reply to Help Needed on 630, 12-06-2006 20:23:23  
Help, below your post Paul in On has a similar problem on a 430 that I replied to as did Roger in MI. Take a look at this post. Roger has some good suggestions too. Could be the end of your shift lever is badly worn allowing the disengagment or lack of engagment. I hadn't considered that. Guess I still expect these old gals to have no wear after 40 years!! He also has some extra pointers and suggestions to try that are similar to mine.

[Log in to Reply]  [No Email]
JGarner

12-07-2006 06:08:15




Report to Moderator
 Re: Paging JGarner and others in reply to Help Needed on 630, 12-06-2006 20:23:23  
It sounds like you have the problem I found myself in a few weeks ago. Can you get either the front or back to lift up any individually? If so, can you see where the rods that the shift forks ride on are positioned?

It sounds like some how the shift lever has jumped out of engagement with the shift forks,is just kind of moving around loosely and the shift rods have been positioned either forward or backward. This moves them under the transmission housing and keeps the cover from coming off. Mine were position so I could get the front up a little but not the back. Hopefully you don't have one shifted forward and the other back!!

If you can "easily" pry either the front or back of the cover up that will tell you which way the rods are moved. I could get the back of mine up only about 1/2 to 3/8 of an inch, but could get the front up about 1 1/2 to 2 inches. I finally, with the help of the drawing in my parts book, found that the shift rails had been moved back when I was trying to position the cover on the transmission housing.

I have an OLD hexagonal nail bar that the shaft is maybe 5/8" diameter and about 12" long that I was able to get behind the rods and pry them to the center and allowed me to take the cover off.

Try this. If you have no success, drop me an e-mail. I have turned my e-mail on. I also correspond regularly with 630crazy and between us we can probably help you out. We both have 630s, the parts books and most of the repair manuals. Somehow I believe we can talk you through the problem.

[Log in to Reply]  [No Email]
[Options]  [Printer Friendly]  [Posting Help]  [Return to Forum]   [Log in to Reply]

Hop to:


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Copyright © 1997-2023 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy