Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver

Attention Forum Users: On the 28th of December 2023 at 9:00am Central Time, we will be taking the forums down for maintenance while we prepare the new forums for your use. Please click here for more information.

Case Tractors Discussion Forum
:

Unsticking a DC

Welcome Guest, Log in or Register
Author 
Kevin5456

11-19-2006 10:46:04




Report to Moderator

How much ($) would it take to un stick an DC or SC engine? My guess that it is more labour intensive than cost. Is that true? any info would be great!
Kevin




[Log in to Reply]   [No Email]
awh

11-21-2006 07:22:56




Report to Moderator
 Re: Unsticking a DC in reply to Kevin5456, 11-19-2006 10:46:04  
Try brake fluid in the cylinders let soak about a week or more then light pressure on the starter ring gear with a pry bar but don't break the teeth off.



[Log in to Reply]  [No Email]
Kevin5456

11-19-2006 15:59:42




Report to Moderator
 Re: Unsticking a DC in reply to Kevin5456, 11-19-2006 10:46:04  
Thanks for the advice. Looks like I have a good bit of work ahead. Take bits and pieces of each reponse. Oldcrane guy, any tran fluid? Would oil work? Diesel Fuel? Kevin



[Log in to Reply]  [No Email]
old

11-19-2006 17:38:42




Report to Moderator
 Re: Unsticking a DC in reply to Kevin5456, 11-19-2006 15:59:42  
Tranny fluid, dextorn 3 works very good been useing it for years now and so far on all the tractor engines I have tried it on only 1 hasn't popped loose for me. I have also used turpentine with the tranny fluid on the tough ones.



[Log in to Reply]  [No Email]
oldcraneguy

11-19-2006 16:18:09




Report to Moderator
 Re: Unsticking a DC in reply to Kevin5456, 11-19-2006 15:59:42  
Yeah, Kevin any tranny fluid or oil will help too, I stay away from diesel cause I once messed up an old 292 ford engine by flushing it with diesel, rinsed all the sludge outa the oil control rings and she smoked like a chimney, it might not bother yours just to get it freed up but I ran the ford engine for about a minute or so with a gallon of diesel in the pan and it was a big mistake, if I was you Id just let it soak for a good while and try to free it up with a bar, I dont know if youve got the gear but Toms method sounds like a good one to me as well..Don

[Log in to Reply]  [No Email]
Kevin5456

11-19-2006 16:05:29




Report to Moderator
 Re: Unsticking a DC in reply to Kevin5456, 11-19-2006 15:59:42  
The reason I am asking is that I was wondering if the DC or SC are worth getting? The price seems right, is it? If the link does not work it is ad 154433 on this website. Kevin



[Log in to Reply]  [No Email]
Kevin5456

11-19-2006 16:08:10




Report to Moderator
 Re: Unsticking a DC in reply to Kevin5456, 11-19-2006 16:05:29  
oldcraneguy,
I dont know if I would be using it. I know that it would not be on a daily bases. Kevin



[Log in to Reply]  [No Email]
oldcraneguy

11-19-2006 16:27:19




Report to Moderator
 Re: Unsticking a DC in reply to Kevin5456, 11-19-2006 16:08:10  
I dont know which parts are common to all 3 tractors but if many are Id say buy em all and have some fun makin the best 1 or2 that you can, as far as storing after theyre loose Id just fill all the cyls with motor oil and check em from time to time to make sure theyre still free, only need to turn em a touch to make sure they still move...
P.S. check all the gearcases for water too.



[Log in to Reply]  [No Email]
Kevin5456

11-19-2006 17:05:44




Report to Moderator
 Re: Unsticking a DC in reply to oldcraneguy, 11-19-2006 16:27:19  
oldcraneguy,
I am not familar with the DC or SC Where would the gearcases be?
Kevin



[Log in to Reply]  [No Email]
oldcraneguy

11-19-2006 17:25:46




Report to Moderator
 Re: Unsticking a DC in reply to Kevin5456, 11-19-2006 17:05:44  
Im not fanilar with them either but theres tranny, rear( may be in same case) and steering gears just make sure there not full of water, callin it a night here...good luck



[Log in to Reply]  [No Email]
Kevin5456

11-19-2006 17:06:49




Report to Moderator
 Re: Unsticking a DC in reply to Kevin5456, 11-19-2006 17:05:44  
I know the gear caswe but the plural to it



[Log in to Reply]  [No Email]
Kevin5456

11-19-2006 16:13:43




Report to Moderator
 Re: Unsticking a DC in reply to Kevin5456, 11-19-2006 16:08:10  
Would hurt if I got it unstuck then put it under a tarp for a year or two intil had the time and money?
What would you suggest that I do it would not get stuck again?



[Log in to Reply]  [No Email]
oldcraneguy

11-19-2006 15:32:01




Report to Moderator
 Re: Unsticking a DC in reply to Kevin5456, 11-19-2006 10:46:04  
Kevin, Walts right in that there is always the chance that if the cyls/rings are rusted bad enough that when you do get it turning it will chew the rings enough that it wont have proper compression(less power) or smoke (burn oil) or both Ive freed up engines that ran great and also some that were not so great, you didnt mention how you planned on using the tractor, is it going to be working the feilds daily? or pull a mower once or twice a month? at any rate if you get it freed up and running and arent happy with the way it performs you can always pull it down and overhaul it...not knowing your particular skills/finances makes it kinda tough to give the best advice...Don

[Log in to Reply]  [No Email]
Walt Davies

11-19-2006 14:45:08




Report to Moderator
 Re: Unsticking a DC in reply to Kevin5456, 11-19-2006 10:46:04  
Rock it about with one tire off the ground if you can't get it to budge then remove head, pan and rod bolt nuts. Then try to push each piston out from the bottom one at a time. You will find that there is a good reason to remove them its called rust and crud that has been built up around the rings. Also the cylinders will have deffinate marks where the rings sat and these need to be honed out. I know you can always luck out and get one running if its not bad but these are rare.
You will be much happier knowing that you did it the correct way when it runs so good after you go completely though it. Walt

[Log in to Reply]  [No Email]
oldcraneguy

11-19-2006 14:30:17




Report to Moderator
 Re: Unsticking a DC in reply to Kevin5456, 11-19-2006 10:46:04  
I was in a hurry when i worked on mine, If youve got time just fill the cyls with tranny fluid and forget about it for a few days should make things easier than my ordeal, I think the ring gear/prybar gives you the best leverage but you can also use a breaker bar on the bolt in the crankshaft pulley if you can get at it, or even put the tractor in high gear high range and try rocking back and forth (another tractor is handy here)...good luck

[Log in to Reply]  [No Email]
oldcraneguy

11-19-2006 14:16:58




Report to Moderator
 Re: Unsticking a DC in reply to Kevin5456, 11-19-2006 10:46:04  
Spent about 6 hrs getting my 320 combo turning..It has a 148ci and the only thing I could touch was the ring gear thru the starter hole..Broke the tips of 2 prybars before the blaster soaked in enough to let it budge, then it was one tooth up two teeth down, two teeth up three teeth down and so on squirtin tranny fluid and anything else I could find the whole way, got to TDC on 2 cyls and it stopped dead in its tracks finally with another new bar got it to go over top , put the starter back in and got it to roll but it almost stuck again the first time those 2 holes came up..I was afraid I had chewed up the rings on the rust ridges but when I got her runnin she ran good with no smoke

[Log in to Reply]  [No Email]
Don Rudolph

11-19-2006 13:46:36




Report to Moderator
 Re: Unsticking a DC in reply to Kevin5456, 11-19-2006 10:46:04  
It depends. Very often it is a stuck valve and that is relatively easy to remedy. On the other hand, it could be a piston/ring/sleeve problem that could get pricey. Kind of hard to tell without pulling it apart and getting into it deeper.



[Log in to Reply]  [No Email]
Kevin5456

11-19-2006 13:08:45




Report to Moderator
 Re: Unsticking a DC in reply to Kevin5456, 11-19-2006 10:46:04  
dctom
That I do not know. How would I go about doing it? Kevin



[Log in to Reply]  [No Email]
dctom

11-19-2006 15:28:09




Report to Moderator
 Re: Unsticking a DC in reply to Kevin5456, 11-19-2006 13:08:45  
knock porceline out of a old spark plug, weld on 1/2 pipe coupling connect hydralic hose to this and screw in plug hole and atach to another tractor hydralic remote, make sure all valves are closed and pump oil, she will come lose, i have broke many DC, M JD G WC and others this way and it works tom



[Log in to Reply]  [No Email]
oldcraneguy

11-19-2006 15:39:44




Report to Moderator
 Re: Unsticking a DC in reply to dctom, 11-19-2006 15:28:09  
Not knowing if Kevin welds or has another tractor I was thinkin that maybe a cyl full of oil and bushed down to screw a grease gun to it might give enough pressure...ya think?



[Log in to Reply]  [No Email]
oldcraneguy

11-19-2006 15:43:15




Report to Moderator
 Re: Unsticking a DC in reply to oldcraneguy, 11-19-2006 15:39:44  
Hey Tom, where the best place to look for my exhaust elbow(post above) not havin much luck so far



[Log in to Reply]  [No Email]
dctom

11-19-2006 16:36:13




Report to Moderator
 Re: Unsticking a DC in reply to oldcraneguy, 11-19-2006 15:43:15  
john saile on this board , he has them tom



[Log in to Reply]  [No Email]
dctom

11-19-2006 12:33:26




Report to Moderator
 Re: Unsticking a DC in reply to Kevin5456, 11-19-2006 10:46:04  
how long it been stuck, i can do it for not more that 300 and a couple gallons of oil tom



[Log in to Reply]  [No Email]
[Options]  [Printer Friendly]  [Posting Help]  [Return to Forum]   [Log in to Reply]

Hop to:


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Copyright © 1997-2023 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy