Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver

Attention Forum Users: On the 28th of December 2023 at 9:00am Central Time, we will be taking the forums down for maintenance while we prepare the new forums for your use. Please click here for more information.

Allis Chalmers Discussion Forum
:

WD45 ingnition trouble (mag)

Welcome Guest, Log in or Register
Author 
Pete S

09-01-2007 09:01:47




Report to Moderator

Long story; I've run this tractor in hot and cold without a hic-cup for 5+ years. The last time I ran it, it simply died while idiling and would NOT start. I pulled a plug to test for firing, then it magically started! It has been parked in our pole building, and tried to get'er to go today..... ....crankity, crankity, and no fire! Played around, and it fired and ran for a short time but died.

SO: I've cleaned all the conact points on the dist cap. I've cleaned the points, and installed a NEW condensor, from my local tractor parts store.
STILL nothing! I'm staring at a pile of 20 tons of gravel..... .shovel and wheel barrow.

Any help to diagnose is greatly appreciated.
I will be out shoveling..... ...I'm too old for this!
Thanks!
Pete

[Log in to Reply]   [No Email]
bill in md

09-01-2007 14:10:21




Report to Moderator
 Re: WD45 ingnition trouble (mag) in reply to Pete S, 09-01-2007 09:01:47  
check the post coming out of the mag where the grounding wire hooks to. mine did the same thing. the wire going to the post was grounding out. insulation around the post was going bad. bypassed the post and ran a new wire to the grounding wire. just adding some ideas for ya. hth



[Log in to Reply]  [No Email]
old

09-01-2007 11:52:31




Report to Moderator
 Re: WD45 ingnition trouble (mag) in reply to Pete S, 09-01-2007 09:01:47  
Send me an e-mail and also tell me which mag you have an I'll send you a manual for it which might help you out



[Log in to Reply]  [No Email]
El Toro

09-01-2007 09:51:50




Report to Moderator
 Re: WD45 ingnition trouble (mag) in reply to Pete S, 09-01-2007 09:01:47  
third party image

A lot of these new condensers aren't worth carrying out the store. The red tractors are having the same problem. Must be from China. You need to make sure you are getting gas to the carburetor and to the engine. Hold your hand over the throat of the carburetor and see if there's good suction while someone cranks the engine. You hand should be wet with gas too.

Make sure your points are nice and shiny. Use a piece of 320 wet or dry and then take a cotton swab dipped in alcohol and clean them again. I would reinstall the old condenser. You need to do the process of elemination by checking for fire at the plugs. If there's fire and a no start check the fuel system for any blockage. I would install a new set of plugs too. Your coil may be weak from age. Pull the coil wire from the mag's cap and hold near a good ground while someone hand cranks the engine. You should have a hot blue spark. Another thing that happens to mags are the magnets in the magneto losing their
magnetism. I have a Wico off an old twin cylinder garden tractor where that has happened.
Its iasy to check if you can get to the magnets by touching them with a flatblade screwdriver. They should attract that screwdriver with a lot of effort. The magnets are what causes the mag to fire when they pass by the coil. Hal
PS: Pic of the old Wico mag.

[Log in to Reply]  [No Email]
Pete S

09-01-2007 10:18:07




Report to Moderator
 Re: WD45 ingnition trouble (mag) in reply to El Toro, 09-01-2007 09:51:50  
I have somewhat completed a trouble shoot.

1.) Utilized a screwdriver and a spare plug to check for spark. NONE

2.) Cleaned the contact surfaces on the inside of the distribtor cap. NO CHANGE

3.) Removed points cover, changed condenser. NO CHANGE

4.) Cleaned points. NO CHANGE

The mag send current to the distribtor cap via a brass rod. Is there a way to safely test to see if the MAG is sending fire?

Thanks!
Pete

[Log in to Reply]  [No Email]
Pete S

09-08-2007 15:25:40




Report to Moderator
 Re: WD45 ingnition trouble (mag) in reply to Pete S, 09-01-2007 10:18:07  
Well, we're back in business!
I didn't have time to have another crack at'er till today, and she's runnin'!

THANKS to the two of you that sent technical information as it was greatly appreciated, and others that contributed advice!

I took it apart AGAIN. This time OFF the tractor. I was careful to have the rotor indexed to the #1 position. The mag was placed in my vice, gently. I took the coil out and noticed that the rotating magnets were a bit rusty. I did have some magnetic pull on a screw driver, but it didn't feel real strong. Cleaned up the rust, wiped things off all over, and reset the points, which were OUT of correct setting.

Then I had a wire lead with aligator clips on each end. Clipped one end to the coil and held the other a bit away from the mag frame,..... spun the mag by hand..... .wah, la, SPARK!

Put'er all back together, and away we went!

Now that pile of gravel and fire wood doesn't look so big!

Thanks again! It's so satisfying to fix something yourself..... ..even if I don't really know what I did!

Pete

[Log in to Reply]  [No Email]
stu (ON)

09-04-2007 04:18:10




Report to Moderator
 Re: WD45 ingnition trouble (mag) in reply to Pete S, 09-01-2007 10:18:07  
See this link.



[Log in to Reply]  [No Email]
El Toro

09-01-2007 12:55:10




Report to Moderator
 Re: WD45 ingnition trouble (mag) in reply to Pete S, 09-01-2007 10:18:07  
Make sure the mag isn't being grounded when in the run position. You may have a toggle switch or some means to shut down the engine and this is usually done by grounding the grounding post. If it has a wire connected to grounging post I would remove it for now.

You can check your mag for fire by removing the coil wire from the mag's cap as I described earlier. Hold it within 1/8 of an inch of a good ground and have someone to make an attempt to start the tractor. If the mag is firing you should get fire from the coil wire every time that impulse coupling snaps. If you have any cracks in old coil wire I would replace it. Make sure the wires on the points where you connected the condenser wire and small coil wire are not touching the metal in the mag. This will ground them out too.


A word of caution if you need to pull the mag from the engine. Make sure you make a note on a sketch where the rotor is pointing. Then after pulling the mag don't move the engine for any reason. When you reinstall the mag you just rotate the rotor to the position shown in your sketch and the mag will be back in time. This applies to a distributor too.

Try cleaning the points with alcohol. I think your coil is weak or the magnets have lost their magnetism. Can you get to the magnets by removing the coil? If the magnets are ok I would have the coil checked. Hal

[Log in to Reply]  [No Email]
Kentb of SWMO

09-01-2007 09:42:50




Report to Moderator
 Re: WD45 ingnition trouble (mag) in reply to Pete S, 09-01-2007 09:01:47  
Coil in mag going bad when hot. Also I do not think WD-45"s came stock with mags.

Kent



[Log in to Reply]  [No Email]
JMS/MN

09-01-2007 12:57:03




Report to Moderator
 Re: WD45 ingnition trouble (mag) in reply to Kentb of SWMO, 09-01-2007 09:42:50  
You're right- Distributor was standard on the 1953 WD, and all WD45 tractors had distributors.



[Log in to Reply]  [No Email]
[Options]  [Printer Friendly]  [Posting Help]  [Return to Forum]   [Log in to Reply]

Hop to:


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Copyright © 1997-2023 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy