Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver

Attention Forum Users: On the 28th of December 2023 at 9:00am Central Time, we will be taking the forums down for maintenance while we prepare the new forums for your use. Please click here for more information.

Allis Chalmers Discussion Forum
:

WC Clutch

Welcome Guest, Log in or Register
Author 
mark peterson

06-27-2007 07:22:32




Report to Moderator

Hello,

I beleive the clutch ahs gone bad in my 40' WC, I can get it ne gear, but when I release the cluth no grip or movement. Is it correct to assume the clutch has gone bad? How hard of a job it it to change?

Thanks,
Mark




[Log in to Reply]   [No Email]
Texas Denny

06-27-2007 10:35:46




Report to Moderator
 Re: WC Clutch in reply to mark peterson, 06-27-2007 07:22:32  
Jerry is absolutely correct. The lever is directly below the steering wheel. It is odd to go so completely so quickly.



[Log in to Reply]  [No Email]
mark peterson

06-27-2007 10:45:43




Report to Moderator
 Re: WC Clutch in reply to Texas Denny, 06-27-2007 10:35:46  
Well, one of the bearings has been squeeling a little bit for some time now, I wouldn't be surprised if it's completely out. I have never noticed a lever below the steering wheel other than the two lever that engage and run the PTO without moving? I checked these at the time when it went out, but I was a little delirious at 10:00 at night trying to finish haying, I will check them again, unless ther is another lever?

[Log in to Reply]  [No Email]
Bill(Wis)

06-27-2007 19:55:53




Report to Moderator
 Re: WC Clutch in reply to mark peterson, 06-27-2007 10:45:43  
The lever they're talking about was a lever that disconnected a dog clutch in the drive train so that you could use the power lift without moving the tractor. It was not a part of the power lift package and most WC's with power lift didn't have it. It had to be ordered separately and if your WC doesn't have it it's probably a clutch problem. Not difficult to fix but you'll have to pull the engine.

[Log in to Reply]  [No Email]
Jerry Coulter

06-27-2007 09:14:09




Report to Moderator
 Re: WC Clutch in reply to mark peterson, 06-27-2007 07:22:32  
You didn't shift the lever into neutral for the live power lift did you? We used to get calls for a clutch job when all it took was to shift that lever.



[Log in to Reply]  [No Email]
Texas Denny

06-27-2007 08:32:38




Report to Moderator
 Re: WC Clutch in reply to mark peterson, 06-27-2007 07:22:32  
I guess anything is possible - but would it be easier? I think the easiest and quickest is to pull the engine. I think pulling the rear axel would be a lot more difficult. The toughest part of pulling the engine is often dis-connecting the steering shaft and removing the radiator. But if you have luck, it can be pulled in an hour or two.

It is very very helpful to have an engine hoist. I have pulled everyone I've done so far with a chain hoist from above - sometimes on the bucket of a front end loader - sometimes on the rafters. Now I have an engine hoist and all mine are rebuilt - I always seem to get tools after I need them rather than before.

[Log in to Reply]  [No Email]
mark peterson

06-27-2007 08:37:08




Report to Moderator
 Re: WC Clutch in reply to Texas Denny, 06-27-2007 08:32:38  
Thanks TD and old,

I beleive experience from you will tell me to "not reinvent the wheel", and pull the engine. Are there any special tools I amy need for this other than a cherry picker?



[Log in to Reply]  [No Email]
mark peterson

06-27-2007 10:40:00




Report to Moderator
 Re: WC Clutch in reply to mark peterson, 06-27-2007 08:37:08  
TD and old,
Thanks for the info, which manual the service manual or parts manual? I should be good on the tools, where is the best place to purchase the clutch, disc, throw out, and pilot bearing from?



[Log in to Reply]  [No Email]
2manytractors

06-27-2007 22:33:54




Report to Moderator
 Re: WC Clutch in reply to mark peterson, 06-27-2007 10:40:00  
If you value this site for information or just good ole comraderie why not buy them right off of this YT site? Their prices are AT LEAST in line with everyone else. I have had excellent parts and service from them.



[Log in to Reply]  [No Email]
old

06-27-2007 10:33:45




Report to Moderator
 Re: WC Clutch in reply to mark peterson, 06-27-2007 08:37:08  
Clutch alimnet tool is a most. You can buy one new at any good auto parts store for around $15 and it you take care of it, it will last 100 plus years. Other then that common tools are all that is needed. If you look in my web site you will see a picture of my WC Speed patrol I pulled the engine on it and drop in a different engine and it took me less then 10 hours total and that was pulling both engines and putting one back in

[Log in to Reply]  [No Email]
Texas Denny

06-27-2007 10:33:40




Report to Moderator
 Re: WC Clutch in reply to mark peterson, 06-27-2007 08:37:08  
A good socket set and a set of box end/open end wrenches are necessary. If the knuckle on the steering shaft has the original pin, you'll need a 5/16" punch and a ball peen hammer. A lot of these had the pin replaced with a bolt in which case, it is easier to remove. You'll need to remove the pin from the starting crank shaft so it will stay forward out of the way. Actually, the pin is on the shaft at the end of the spring. When you remove this pin, the shaft will go forward another inch or two (it isn't the pin that engages the pulley). Never hurts to have an IT manual. Screwdrivers for the hoses are needed. And you'll probably need a couple of pry bars once the engine is free to move it ahead a couple inches before lifting.

[Log in to Reply]  [No Email]
old

06-27-2007 07:55:17




Report to Moderator
 Re: WC Clutch in reply to mark peterson, 06-27-2007 07:22:32  
Yep sounds like its gone. You need to pull the engine to put in a new clutch. If you do it I would replace the clutch disk, pressure plate, throw out bearing and pilot bearing and be done with it for decades. Not to bad a job to do if you have the right tools for the job. Engine hoist etc



[Log in to Reply]  [No Email]
old

06-27-2007 07:54:36




Report to Moderator
 Re: WC Clutch in reply to mark peterson, 06-27-2007 07:22:32  
Yep sounds like its gone. You need to pull the engine to put in a new clutch. If you do it I would replace the clutch disk, pressure plate, throw out bearing and pilot bearing and be done with it for decades. Not to bad a job to do if you have the right tools for the job. Engine hoist etc



[Log in to Reply]  [No Email]
mark peterson

06-27-2007 08:04:22




Report to Moderator
 Re: WC Clutch in reply to old, 06-27-2007 07:54:36  
Is it possible to leave the engine in the frame, support the frame, and roll the rear assembly away to change it?



[Log in to Reply]  [No Email]
old

06-27-2007 10:22:37




Report to Moderator
 Re: WC Clutch in reply to mark peterson, 06-27-2007 08:04:22  
You might be able to but it is easier to pull the engine then to do it that way. I know I can have the engine out of one in less then an hour and then back in in about an hour.



[Log in to Reply]  [No Email]
[Options]  [Printer Friendly]  [Posting Help]  [Return to Forum]   [Log in to Reply]

Hop to:


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Copyright © 1997-2023 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy