Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver

Attention Forum Users: On the 28th of December 2023 at 9:00am Central Time, we will be taking the forums down for maintenance while we prepare the new forums for your use. Please click here for more information.

Allis Chalmers Discussion Forum
:

Allis Chalmers Wd

Welcome Guest, Log in or Register
Author 
Justin Squire

12-26-2005 14:10:15




Report to Moderator

Several questions pertaining to the restoration of a WD:
I realized there was no easy to take the oil pan off and work on the engine without taking it out so what is the best way to remove the engine? I have a hoist and engine stand.

Also, what is the best way to remove paint and rust from sheet metal without sandblasting? I am looking into a handheld belt sander.

What is the best way to clean a cylinder head and other cast iron components at home?

Also, does anybody know if the Tune up kit offered by the parts section on this website will work for a late WD? Does it have all the parts to repair the distributor? I don't think there is a distributor dust cover included. Is there a dust cover available for sale anywhere?

Does anybody know if the key actually had significance on the key ignition switch? my tractor has the switch, but no keys. I tried a screwdriver and the switch turns with no key.

Any help would be appreciated. Thank you.

[Log in to Reply]   [No Email]
Gordon in IN

12-27-2005 16:04:18




Report to Moderator
 Re: Allis Chalmers Wd in reply to Justin Squire, 12-26-2005 14:10:15  
The oil pan on a WD Allis is very easy to remove with the engine in the tractor. You do not have to remove the engine from the tractor. If you need to remove the engine, to replace the clutch, pressure plate, throw out bearing, or camchaft bearings, it is about the easiest tractor engine to remove that there is. The hyd. engine hoist will make the job easier. If you remove the engine for any reason, I would suggest you replace the cam bearings unless they are "like new". Also suggest that you replace the oil pump with a WD 45 "high capacity" oil pump. If you have the cam shaft out, you might want to drill an extra set of oil holes in the center camshaft bearing. (Provides twice the oil flow area into the camshaft that goes out each camshaft end bearing) Remember that the camshaft is the oil gallery for the front and rear main bearings and supplies oil for the #1 and #4 connecting rod bearings as well. Suggest setting the oil pressure at 18 to 20 P.S.I. not higher. The IT Manual is a very good idea. Good luck in your efforts.

[Log in to Reply]  [No Email]
J.C. IN AZ.

12-26-2005 22:08:26




Report to Moderator
 Re: Allis Chalmers Wd in reply to Justin Squire, 12-26-2005 14:10:15  
For quick and effortless paint removal I use "Strip-ez" Paint comes right off down to bare metal.Careful "Prep" should follow.



[Log in to Reply]  [No Email]
chalmersbob

12-26-2005 18:37:47




Report to Moderator
 Re: Allis Chalmers Wd in reply to Justin Squire, 12-26-2005 14:10:15  
you don't want a belt sander. the better choice is a random orbital sander with dust pickup.
the oil pan will come down without removing the engine.
to remove engine you must remove the radiator, front pulley, cross support, and of course the bolts out of the bellhousing. good luck with your project. BOB



[Log in to Reply]  [No Email]
chalmersbob

12-26-2005 18:37:15




Report to Moderator
 Re: Allis Chalmers Wd in reply to Justin Squire, 12-26-2005 14:10:15  
you don't want a belt sander. the better choice is a random orbital sander with dust pickup.
the oil pan will come down without removing the engine.
to rempove engine you must remove the radiator, front pulley, cross support, and of course the bolts out of the bellhousing. good luck with your project. BOB



[Log in to Reply]  [No Email]
old

12-26-2005 15:03:38




Report to Moderator
 Re: Allis Chalmers Wd in reply to Justin Squire, 12-26-2005 14:10:15  
Well on the WD you pull the engine with a hoist, been there done that. Best way to answer a lot of your question is for you to buy an I-T manual AC-11 it cover a lot of your question. As far as parts the best place to get them is an ARCO ag dealer. And or people like me who have parts tractors in the junk yard.



[Log in to Reply]  [No Email]
JMS/MN

12-28-2005 17:12:16




Report to Moderator
 Re: Allis Chalmers Wd in reply to old, 12-26-2005 15:03:38  
AGCO dealer locator is at www.agcocorp.com.



[Log in to Reply]  [No Email]
[Options]  [Printer Friendly]  [Posting Help]  [Return to Forum]   [Log in to Reply]

Hop to:


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Copyright © 1997-2023 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy