Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver

Attention Forum Users: On the 28th of December 2023 at 9:00am Central Time, we will be taking the forums down for maintenance while we prepare the new forums for your use. Please click here for more information.

Allis Chalmers Discussion Forum
:

WD45 in WC

Welcome Guest, Log in or Register
Author 
UUsee

12-22-2003 14:19:38




Report to Moderator

Installing a WD45 Crank in a WC.Crank came with bearings for a WD45.Book says WC's had shimed bearings,although there were no shims when disassembled.Main bearings are in the block and the caps and the crank is in,but I have not torqued it yet cause it feels real tight just laying on the bearings with no hold down pressure at all.Am I going to need to get WC bearings or shims or what?




[Log in to Reply]   [No Email]
LDL

12-27-2003 06:20:39




Report to Moderator
 Re: WD45 in WC in reply to UUsee, 12-22-2003 14:19:38  
WC bearings and WD45 bearing are exactly the same. The difference is in the block and caps. Get shim packs and plasti-guage each bearing. This will show correct clearance as you remove shims. The caps from the WC block must be used in their corect position, not backwards. Do not put the WD45 caps in the WC block if you have them also do not mix rod caps. Each rod has a matching cap and all caps only go on one way. For rod caps make sure the stamped number or punch marks are put together facing the cam shaft and have a matching number. The main bearing caps also should have some kind of marking and should also be installed with marking facing the cam shaft. It is possible the block has been machined so as not to use shims but start with shims first otherwise you could stretch the caps which is bad.

[Log in to Reply]  [No Email]
Kip [UT]

12-24-2003 08:11:42




Report to Moderator
 Re: WD45 in WC in reply to UUsee, 12-22-2003 14:19:38  
On the outside chance that this is an early WC block that used the small journal crank, it is still a drop in proposition w/ the proper larger bearings. The early ones were almost always refit w/ one of the large journal WC cranks the first time that they were over-hauled. WC,WD,WD45 internals will all mix & match w/ the exception of pistons. 45 cranks must use the power-crater pistons & the 4" stroke cranks must use the flat tops. Connecting rods are the same in all engines. The D17 & E combine engines are essentially the same as a WD45 except w/ larger crank journals that prevent them from working in the W series engines, however a 17 type engine is nearly a boltin fit on the W series tractors.

[Log in to Reply]  [No Email]
Chuckster

12-25-2003 07:08:19




Report to Moderator
 Re: Re: WD45 in WC in reply to Kip [UT], 12-24-2003 08:11:42  
Why cant you use the flat top pistons with the 45 crank wont they raise the compresion a little bit



[Log in to Reply]  [No Email]
Kip [UT]

12-26-2003 22:08:30




Report to Moderator
 Re: Re: Re: WD45 in WC in reply to Chuckster, 12-25-2003 07:08:19  
Yes they will raise compression ALOT! Too much even for a mildly built pulling engine, my oppinion remains that the flat tops only belong on 4" stroke cranks.



[Log in to Reply]  [No Email]
Chuckster

12-27-2003 05:39:48




Report to Moderator
 Re: Re: Re: Re: WD45 in WC in reply to Kip [UT], 12-26-2003 22:08:30  
Whell my freind and I have built a 201 whith the 45 crank and the fire crater pistons and it runs great.We are now going to try the flat tops.Just looking at the wrist pin location it doesnt look to be a problem. Have a happy NewYear.....



[Log in to Reply]  [No Email]
L Hud

12-23-2003 07:37:57




Report to Moderator
 Re: WD45 in WC in reply to UUsee, 12-22-2003 14:19:38  
Both the WC and 45 has to have shims on the crank. The crank must be shimmed unless you have had machine work done on the block. 45 rods does not use shims. WD and WC rods used shims. Hope this helps.



[Log in to Reply]  [No Email]
UUsee

12-23-2003 17:09:09




Report to Moderator
 Re: Re: WD45 in WC in reply to L Hud, 12-23-2003 07:37:57  
Thank you! I also came to that thought this afternoon when I spent some time [hours] checking dimensions with micrometers.Will order shim packs.



[Log in to Reply]  [No Email]
wdTom

12-23-2003 18:43:44




Report to Moderator
 Re: Re: Re: WD45 in WC in reply to UUsee, 12-23-2003 17:09:09  
You can make shims if you want to. Drill hole in two pieces of metal the size of you need for bolt or capscrew. Fasten two peices together with about a 1/16" gap between them with holes lined up. Use a sharp, square piece of rod that fits hole as a punch to punch hole in shim stock. Not hardened but will work for a good number of shims.



[Log in to Reply]  [No Email]
Chris

12-23-2003 06:05:58




Report to Moderator
 Re: WD45 in WC in reply to UUsee, 12-22-2003 14:19:38  
Think of it like this. You are fitting the crank into the block. The bearings and caps are part of the BLOCK not the Crank so therefor you need to use the WC bearings and caps and adjust them to accept the different crank. You can have the block line bored to accept the WD-45 bearing. Talking some $$$ here.



[Log in to Reply]  [No Email]
wdTom

12-22-2003 19:03:46




Report to Moderator
 Re: WD45 in WC in reply to UUsee, 12-22-2003 14:19:38  
I would say you need proper clearence, and proper cursh no matter which bearings you are using. Use plastigage to check your clearence with the bearings fairly tight. You need to start out with some allowence for "crush". That is with the bearings in and on the block but not more than finger tight you need to have a few thousands clearance between the bearing cap and block. This makes a "press fit" for the bearing shells when the cap is torqued down and keeps the bearing shells in place and allows heat transfer to the block and cap. Always place bearing shells in the caps dry and clean. It can take a while to sneak up on the proper crush and bearing clearence. If the berings are tight before torqueing you may have a problem, shims will not increase the bearing clearence. You may need the help of a good engine shop to get it all straightened out. To reduce clearence you carefully and evenly file the ends of the bearing shell, then reduce the shims a like amount to maintain your crush.

[Log in to Reply]  [No Email]
John (AZ)

12-22-2003 16:48:51




Report to Moderator
 Re: WD45 in WC in reply to UUsee, 12-22-2003 14:19:38  
sounds like you need to get the shim packs to get the proper clearances. I'm not sure if the WD-45 bearings will work in a WC block.



[Log in to Reply]  [No Email]
old

12-22-2003 16:27:47




Report to Moderator
 Re: WD45 in WC in reply to UUsee, 12-22-2003 14:19:38  
I don't believe it will work since a WC has a smaller engine then a WD45 has, the WC and the WD have the same engine but the WD45has a 228 engine with a 4.5 stroke and the WC/WD has a 4 inch stroke and is 201ci engine



[Log in to Reply]  [No Email]
UUsee

12-23-2003 04:21:27




Report to Moderator
 Re: Re: WD45 in WC in reply to old, 12-22-2003 16:27:47  
It will work,just got to get the bearings situated right.As I said the crank is already sitting in the block and clearance of the throws does not seem to be a problem.WD45 has more cubes but not a bigger block,226civs 201



[Log in to Reply]  [No Email]
jerry

12-22-2003 18:53:08




Report to Moderator
 Re: Re: WD45 in WC in reply to old, 12-22-2003 16:27:47  
Size of crankshaft journals were small in early 1933 wc to 1936. 1936 WC, WD, and 45 were of the same size. Thats according to an old parts supply book. Tolerance should only be .002 to .003 on main journals. If I remember corrctly the wc & wd had 4 shims while 45 has factory fit bearings. You might have early block in WC.



[Log in to Reply]  [No Email]
[Options]  [Printer Friendly]  [Posting Help]  [Return to Forum]   [Log in to Reply]

Hop to:


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Copyright © 1997-2023 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy