Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver

Attention Forum Users: On the 28th of December 2023 at 9:00am Central Time, we will be taking the forums down for maintenance while we prepare the new forums for your use. Please click here for more information.

Allis Chalmers Discussion Forum
:

Spark Plug Confirmation

Welcome Guest, Log in or Register
Author 
Trevor

09-09-2003 05:35:53




Report to Moderator

I think I already know the answer to my question but I just want to confirm it with you guys.

My father has a B and a CA. The CA has been converted to 12V and works excellent (except for the hand clutch slipping but that's another story). The B however has a Mag and doesn't run smooth at idle. I changed the cheap carbon wires acouple of weeks ago to solid copper and was very disappointed when I saw no difference in idle. I have now checked the plugs and I know that you guys swear by Autolite 295. Well father assusres me that the fellas in at the NAPA stored looked up the proper plugs but when I checked they are AC Delco R45 plugs. If I understand what I have read in the past and in the achives these are not the right plugs.

The CA has the same plugs however like I said it is 12 V coil ignition so maybe we can't see it.

Am I right? Should I change both the CA and the B plug or can I leave the CA alone?

Thanks for any advice. You guys have always been good to me in the past.

[Log in to Reply]   [No Email]
Bryan Smith

09-10-2003 12:17:36




Report to Moderator
 Re: Spark Plug Confirmation in reply to Trevor, 09-09-2003 05:35:53  
OK, Trevor, one other thing to check besides carb rebuilds, sediment, plugs, and so forth - your carb's venturi. If it's loose you'll get idle problems. Take the two carb halves apart, remove the gasket, then put the two halves back together with the venturi in place. If there is a small gap between the two body halves (like a spark plug gap size - .020 to .030") you're ok. If not the venturi's moving around and causing problems.

I had an older guy tell me about this. He also said I could make a thin, washer-type spacer to fit around the bottom of the venturi if it was loose. Mine in my 1949 B was loose (the two carb body halves fit together flush with *no* space when I tried this), and I did install a spacer made out of some 17 gauge aluminum electric fence wire curled in a circle and hammered flat. It's not perfect, mind you, but now I can throttle down and expect a reasonable idle. Before I really didn't take it below notch 5. Still an occaisional miss, but it's an often overlooked problem that I thought might be worth mentioning. I *might* also have a manifold leak, but the improvement was so huge in mine that I haven't looked further yet!

[Log in to Reply]  [No Email]
Ken/Wa

09-09-2003 23:05:11




Report to Moderator
 Re: Spark Plug Confirmation in reply to Trevor, 09-09-2003 05:35:53  
Check for manifold leaks. I had mine milled, and it smoothed out. Some spray WD-40 and listen for increased RPM.



[Log in to Reply]  [No Email]
TexMac

09-09-2003 20:02:30




Report to Moderator
 Re: Spark Plug Confirmation in reply to Trevor, 09-09-2003 05:35:53  
Have used Japanese plugs for about 30 years, even in my '50 Flathead Ford V8. Have NGK B6S's in my '39 AC-B. Idles like a sewing machine and just as smooth at full power. One question - How do I get them out when they need changing?!! Tried to look at one the other day and could only get one wrench in my tool box to clear the head bosses around the plug holes and it slips. Do you fellows that use them have any tricks you can teach me to get a plug wrench on the B6S's or some other trick to get them loose short of breaking them and drilling them out? I sure don't look forward to pulling the head.

[Log in to Reply]  [No Email]
Tyler(WA)

09-10-2003 12:28:36




Report to Moderator
 Re: Re: Spark Plug Confirmation in reply to TexMac, 09-09-2003 20:02:30  
Autolite 295's have a long base on them and puts the hex/flats up above the head bolsters.



[Log in to Reply]  [No Email]
Rod (NH)

09-10-2003 14:00:25




Report to Moderator
 Re: Re: Re: Spark Plug Confirmation in reply to Tyler(WA), 09-10-2003 12:28:36  
Hi Tyler,

Not on my '42B. The 295 hex is slightly recessed. Enough so that I would not like to change 'em with an open end or adjustable wrench. Not saying it can't be done. But it really is not the right tool for the job, even for the 295. Or even for the original AC45 for that matter. The NGK B6S does have a slightly shorter body length below the hex of about 1/16" than the 295. But it is identical dimensionally to the original AC45. The NGK B4 is exactly the same dimension as the 295.

My recommendation is to use the correct tool. That's probably why AC included the deep sparkplug socket with the tractor. I still have mine somewhere but I never use it. A standard sparkplug socket in a 3/8 drive ratchet is just easier.

third party image Rod

[Log in to Reply]  [No Email]
TexMac

09-11-2003 13:14:34




Report to Moderator
 Re: Re: Re: Re: Spark Plug Confirmation in reply to Rod (NH), 09-10-2003 14:00:25  
Wish I had realized that 1/16" difference was there. I have a pretty well equiped shop with several brands of plug wrenches. None seem to work. Probably a 6 point socket would do the job, but then the walls are too thick. I even got desperate and went out and bought one of those plug wrenches that looks like it is stamped out of sheet metal since it was 6 point. They are just too cheap and sloppy. I don't want to round the plug and compound the problem. I guess what I need to know is what brand plug wrench you guys use on your B6S's.

[Log in to Reply]  [No Email]
Rod (NH)

09-11-2003 14:32:19




Report to Moderator
 Re: Re: Re: Re: Re: Spark Plug Confirmation in reply to TexMac, 09-11-2003 13:14:34  
Boy, TexMac maybe I just don't understand the problem. We are talking an AC model B tractor and an NGK B6S plug, right?. I just replaced (for my own information) an Autolite 295 with an NGK B6S plug on my '42 B. ALL the following wrenches work fine. The 1/16" difference in height makes no difference at all that I can detect.

1. Craftsman flex-head sparkplug socket
2. S-K flex head sparkplug socket
3. Indestro straight sparkplug socket
4. Craftsman standard deep socket

All these sockets are 6 point, 13/16" size. None of them caused a problem. None of them are special or unique as far as I know. I could fully engage the hex with any of them. I did try a deep impact socket and the wall thickness was too great to get a proper, complete engagement. So if you are using impact sockets that could be your problem. The only other thing that I can think of is that the head for the '39 is different than for the '42, although I would not expect that to be the case since they seem to carry the same part number.

third party image Rod

[Log in to Reply]  [No Email]
TexMac

09-11-2003 22:52:03




Report to Moderator
 Re: Re: Re: Re: Re: Re: Spark Plug Confirmation in reply to Rod (NH), 09-11-2003 14:32:19  
Thanks Rod. You answered my question. Every thin wall plug wrench I owned was 12 point one of which put them in and torqued up nicely, my good 6 point was a little thicker and would not quite clear. You are right that no impact socket would ever work in that space. I'll try to get an S-K at the parts house tomorrow. The 12 points just would not bite properly. I think the heads are the same. Appreciate the help from every one. Still like those plugs!

[Log in to Reply]  [No Email]
Rod (NH)

09-09-2003 20:49:02




Report to Moderator
 Re: Re: Spark Plug Confirmation in reply to TexMac, 09-09-2003 20:02:30  
Hi TexMac,

Hmmm. I can't say that I have ever had a problem with either the B6S or the B4 in my '42B. I use a standard spark plug socket on 'em. I haven't inspected them in detail but as far as I know, the basic dimensions are no different than any other similar plug, such as the Autolite 295. Are you using a regular thin wall deep sparkplug socket? If not, that may be your problem.

third party image Rod

[Log in to Reply]  [No Email]
Mike(Oh)

09-09-2003 19:34:30




Report to Moderator
 Re: Spark Plug Confirmation in reply to Trevor, 09-09-2003 05:35:53  
Ok so by the NGK chart I have been wrong all these years. The Autolite 303's are actually a hotter plug than the 295's. Boy to I have some people to contact.



[Log in to Reply]  [No Email]
Rod (NH)

09-09-2003 20:33:40




Report to Moderator
 Re: Re: Spark Plug Confirmation in reply to Mike(Oh), 09-09-2003 19:34:30  
Hi Mike,

No, you have NOT been wrong. The numbering system Autolite uses for heat range is just opposite from the one NGK uses. For Autolite, the last digit is the indicator of heat range, not the entire number. In other words, the 5 in 295 should be compared with the last 3 in 303. Autolite uses higher numbers to indicate hotter plugs. 5 is higher than 3 so the 295 is hotter than the 303.

third party image Rod

[Log in to Reply]  [No Email]
Mike(Oh)

09-10-2003 05:54:36




Report to Moderator
 Re: Re: Re: Spark Plug Confirmation in reply to Rod (NH), 09-09-2003 20:33:40  
Thanks for the info Rod. Really misread the NGK chart last night. Thought the 303 xrefed to a hotter NGK plug. After reading your post and looking at the chart again I have no idea what I was thinking last night but I have got it straight now � Mike(Oh).



[Log in to Reply]  [No Email]
Steve in N.J.

09-09-2003 14:58:56




Report to Moderator
 Re: Spark Plug Confirmation in reply to Trevor, 09-09-2003 05:35:53  
Trevor,
We, like Jim carry the Autolites in stock, and move quite a few, but like Rod, I've been experimenting with the NGK's in my B, and so far they've worked flawlessly. I have the B6S NGK's screwed in my engine which is a little warmer plug. I guess it's whatever works the best for you. I would loose the resistor plugs anyway though. (At least their not Champions)LOL! As for the rough idle, that may not be the mag, that could easily be fuel related or a fuel mix problem... Good Luck! Hope you get the ole B ironed out!
Steve/B&B Custom Circuits

[Log in to Reply]  [No Email]
Rod (NH)

09-09-2003 15:52:34




Report to Moderator
 Re: Re: Spark Plug Confirmation in reply to Steve in N.J., 09-09-2003 14:58:56  
Hi Steve,

I always enjoy reading your posts. Especially one during the ammeter vs voltmeter discussion on the "other board" :o). As far as I know, NGK designates a higher heat range by decreasing numbers. Just the opposite of many others. The B4 is a direct cross to the AC45 as shown here. I think the B6S is a little colder plug than the B4 but I could be mistaken. In any event, I have also used the B6S successfully in my B as you have.

third party image Rod

[Log in to Reply]  [No Email]
Steve in N.J.

09-09-2003 18:54:52




Report to Moderator
 Re: Re: Re: Spark Plug Confirmation in reply to Rod (NH), 09-09-2003 15:52:34  
Rod,
You're absolutely right! I'm thinking bass-akwards here. I made up a saying for myself for next time. "NGK is the other way." Sorry guys, I don't want to mislead ya. BTW- Rod, you come up with some great info yourself! I to enjoy reading your research.We never stop learning! It's great! Steve/B&B Custom Circuits



[Log in to Reply]  [No Email]
Trevor

09-09-2003 16:07:13




Report to Moderator
 Re: Re: Re: Spark Plug Confirmation in reply to Rod (NH), 09-09-2003 15:52:34  
Rod,

You were absolutely correct. I went to there site and checked and the numbers run opposite to what you think they would. 2 is the hottest and 11 the coolest.

Good thing you mentioned that. I guess I will go with the B4 then like Jim suggested.

Thanks guys, I have learned alot with your help.

I was lucky to get a lot of the people I really trust and enjoy reading their posts to post on my question.

[Log in to Reply]  [No Email]
Trevor

09-09-2003 15:08:13




Report to Moderator
 Re: Re: Spark Plug Confirmation in reply to Steve in N.J., 09-09-2003 14:58:56  
Steve,

We tried adjusting the carb first. We have completely rebuilt this engine and disassembled and cleaned the carb but nothing helped. That's why we are now looking at spark.

You seem quite knowledgable about spark plugs, what does "a little warmer" mean. Don't get me wrong here I know what hot vs cold is but in spark plug terms.

It can't mean a longer arc because you gap the plug. Is the resistance of the core different? Is the material of the electrode different?

Just curious. I'm an Electrical Technologist and never really understood what the temp of a spark plug referred to.

Thanks for posting. Right now I think I might try your B6S plugs. A little extra heat in the plug might help.

[Log in to Reply]  [No Email]
Trevor

09-09-2003 15:57:46




Report to Moderator
 Re: Re: Re: Spark Plug Confirmation in reply to Trevor , 09-09-2003 15:08:13  
OK, all this spark plug talk made me curious and I went to the NGK web site. It is very informative and I learned what Temp refers to as far as spark plugs go.

If anyone is interested try the link and go to the Tech section there is 5 pages on spark plug basics. I also recommend the page that breaks down the part # for you.

[Log in to Reply]  [No Email]
Dick L I Hear What Is Sai

09-09-2003 08:34:12




Report to Moderator
 Re: Spark Plug Confirmation in reply to Trevor, 09-09-2003 05:35:53  
But I have used the AC R 45 spark plugs in my C Allis pulling tractor for the five or six years I have been pulling. At one time I had a fouling problem but when I got the fuel mixture correct the fouling stopped. I now have two sets of the Autolite 295's in the truck to put in if these seem to give out. If you ask anyone that pulls against me I am sure they will atest to the fact I do not have a loss of power.

[Log in to Reply]  [No Email]
Trevor

09-09-2003 11:03:55




Report to Moderator
 Re: Re: Spark Plug Confirmation in reply to Dick L I Hear What Is Sai, 09-09-2003 08:34:12  
DickL,

Is your C Mag or Coil? Do you feel it makes a difference?

The old mag has not been rebuilt but the price of spark plugs is cheaper than a mag rebuild and we can change the plugs in a couple of minutes.

Thanks for posting



[Log in to Reply]  [No Email]
Rod (NH)

09-09-2003 07:30:17




Report to Moderator
 Re: Spark Plug Confirmation in reply to Trevor, 09-09-2003 05:35:53  
Hi Trevor,

The plugs specified in the AC service manual for the B are AC-45 for the gas engine. Loose the R which is for resistor type plugs.

I'll give you my own personal experience. I have used the AC-45 for many years in my '42B (magneto ignition) with good sucess. Somewhere around 10 years ago I seemed to have trouble getting the AC-45. I am not sure but that non-resistor version may have been dropped. In any event, I switched to NGK B-4 and also have had good luck with them over the past 10 years or so. I use solid core wires, made up from gross lengths.

This year I decided to try the Autolite 295 that seems to be the talk of the town here and on the other board. I have NOT noticed any difference whatsoever in either starting or running. No better, no worse. I have come to suspect that the hype about the 295 is overblown. I change my plugs once a year for good measure (working B) and will likely go back to the NGKs, which are more readily available locally, next year.

As they say, your mileage may vary :o).

third party image Rod

[Log in to Reply]  [No Email]
Bryan Smith

09-10-2003 12:09:35




Report to Moderator
 Re: Re: Spark Plug Confirmation in reply to Rod (NH), 09-09-2003 07:30:17  
Don't disagree with your thoughts on the AC 45 plugs, Rod - I used them for years and they seemed to work well. Champions didn't. Period.

But, since the 45 is no longer available (replaced by the R45 as you know) I'm using Autolite 303's now (all my tractors are distributor right now - I'd use 295's in a magneto setup). About the same as an AC 45 in performance, lots better than Champions as far as I can tell.

What's not hype is the quality - I've gotten a bad AC 45 new right out of the box on occaision, but that's never happened with Autolites. Maybe I'll get a bad Autolite one day. My auto parts guy says the Autolite is a high-quality made plug - take that for what it's worth.

I've tried the R45's and they seem to do ok, but they just don't seem to go as long in an older motor (read may be due for an overhaul in a few years) as the non-resistor 303's or 295's do. Just personal experience in a warm, humid climate.

[Log in to Reply]  [No Email]
Rod (NH)

09-10-2003 14:16:47




Report to Moderator
 Re: Re: Re: Spark Plug Confirmation in reply to Bryan Smith, 09-10-2003 12:09:35  
Hi Bryan,

I am curious as to why many seem to think that a colder plug (303) would be better for a battery ignition than the hotter 295 (claimed for the mag ignition) in the exact same engine. I am not sure I understand the reasoning. AC doesn't make any distinction between the two in their service manual for the B&C. Any thoughts? Anyone?

third party image Rod

[Log in to Reply]  [No Email]
Bryan SMith

09-11-2003 06:39:45




Report to Moderator
 Re: Re: Re: Re: Spark Plug Confirmation in reply to Rod (NH), 09-10-2003 14:16:47  
Quite honestly I think a 295 would work in all applications we are talking about as a replacement for an AC 45. No idea where the 303 idea came from, but it works well.



[Log in to Reply]  [No Email]
Trevor

09-09-2003 11:06:05




Report to Moderator
 Re: Re: Spark Plug Confirmation in reply to Rod (NH), 09-09-2003 07:30:17  
Rod,

Thanks for that info. We too have a problem finding Autolite plugs in this area but I know I can get the NGKs. Maybe I will try the NGKs first.

Thanks for posting.



[Log in to Reply]  [No Email]
Trevor

09-09-2003 11:07:28




Report to Moderator
 Re: Re: Spark Plug Confirmation in reply to Jim Danforth , 09-09-2003 06:32:14  
Jim,

I take it that the 303 is a resistor plug like the 45R.

Thanks for posting



[Log in to Reply]  [No Email]
Mike(Oh)

09-09-2003 13:43:07




Report to Moderator
 Re: Re: Re: Spark Plug Confirmation in reply to Trevor, 09-09-2003 11:07:28  
I do not think 303's are resistor plugs - just cooler than 295's. If the links work they are from the autolite site but I am still kinda confused about what the numbers stand for.
Link
http://www.autolite.com/tech/SparkPlugNumberingSystem.pdf



[Log in to Reply]  [No Email]
[Options]  [Printer Friendly]  [Posting Help]  [Return to Forum]   [Log in to Reply]

Hop to:


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Copyright © 1997-2023 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy