Welcome! Please use the navigational links to explore our website.
Company Logo (800) 853-2651 Shop Now
   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver

Allis Chalmers Discussion Forum
:

Cylinder O-rings

Welcome Guest, Log in or Register
Author 
Harmon Moody

09-08-2003 18:21:31




Report to Moderator

Need to find a source for O-rings that are on the cylinders.




[Log in to Reply]   [No Email]
Harmon Moody

09-08-2003 18:25:11




Report to Moderator
 Re: Cylinder O-rings in reply to Harmon Moody, 09-08-2003 18:21:31  
The model for o-rings is a WD



[Log in to Reply]  [No Email]
steve

09-09-2003 20:39:22




Report to Moderator
 Re: Re: Cylinder O-rings in reply to Harmon Moody, 09-08-2003 18:25:11  
i would think someone like normstoys.com would have them. i measured mine on the B motor i overhauled and bought a box of 25 from McMaster Carr for $20. have enought for next motor, smaller than a WC.



[Log in to Reply]  [No Email]
Harmon Moody

09-11-2003 14:03:49




Report to Moderator
 Re: Re: Re: Cylinder O-rings in reply to steve, 09-09-2003 20:39:22  
David. Could not find .140. Next size up would be 3/16 or .1857. I appreciate any help you can give.



[Log in to Reply]  [No Email]
David

09-09-2003 20:43:47




Report to Moderator
 Re: Re: Re: Cylinder O-rings in reply to steve, 09-09-2003 20:39:22  
The WD O'rings are .140 cross section with 4.00 ID and are made of Neoprene. McMaster Carr lists them in their catalogue.



[Log in to Reply]  [No Email]
[Options]  [Printer Friendly]  [Posting Help]  [Return to Forum]   [Log in to Reply]

Hop to:


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Today's Featured Article - Timing Your Magneto Ignition Tractor - by Chris Pratt. If you have done major engine work or restored your tractor, chances are you removed the magneto and spark plug wires and eventually reached the point where you had to put it all back together and make it run. On our first cosmetic restoration, not having a manual, we carefully marked the wires, taped the magneto in the position it came off, and were careful not to turn the engine over while we had these components off. We thought we could get by with this since the engine ran perfectly and would not need any internal work. After the cleanup and painting was done, we began reassembly and finally came to t ... [Read Article]

Latest Ad: Wanted 13x28 power adjust rim for D 17 allis in NE Nebraska [More Ads]

Copyright © 1997-2023 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy