FREE SHIPPING on orders above $249.99! Details

• Tractor Parts

• Engine Kits

• Carburetors

• Salvage

• Manuals

• DVDs

• Hats

• Contact Us

• Shipping Rates

• Return Policy

• Ordering Help

• Company Info

• Parts Warranty

• Forums

Ferguson 3165 Parts

[Categories] [All Ferguson Models] [Print]

Brakes

Brake Drum - Brake drum 16 inch outside dia 4 1/2 inch hub diameter. For tractors: TO35, MF35, F40, MH50, MF50, MF135 (except orchard), MF150, MF230, MF235 (except orchard), MF240, MF245 (except orchard). Industrials: 20, 20C, 20D, 30 turf, 35, 40, 202, 204, 2135, 2200, 3165. Uses two 182278M1 retaining screws per drum (not included). Replaces 181230M1, 827707M91, 827707M7, 827707M6, 827707M3, 825631M91, 822707M5, 8207707M4, 181230M1, 827707M1, 827707M4, and A827707M5. (Item #: 105637, Ref: 827707M5) $93.60

Brake Drum Retaining Screw - This Brake Drum Retaining Screw Measures 1/2 -13 NC x 3/4 inches. Four are used per tractor, sold individually. If you order 1, you are only going to get one screw. It is used on the following with shoe style brakes: 2200, 2135, 3165, 20C, 20D, 30, FE35, TE20, TEA20, TO20, TO30, F40, TO35, 130, 20, 202, 204, 35, 135, 148, 150, 230, 231, 240, 245, 340, 35, 50, MH50, 550. It is used with 827707M5 Break Drum. Replaces: 182278M1, TO1127. (Item #: 125739, Ref: 182278M1) $1.90

Brake Pedal Shaft - This Brake Pedal Shaft is used on Ferguson F40, TO35, Massey Ferguson 135, 150, 3100, 3165, 20, 2135, 30, 35, 50, Massey Harris 50. Replaces 181959M1, 1860802M1, 200191M1 (Item #: 180160, Ref: 1860802M1) $47.80

Spring, Parking Brake Latch - For tractor models F40, FE35, TO35, 1080, 1085, 135, 135 UK, 150, 165, 165 UK, 175, 175 UK, 178, 20, 230, 235, 240, 282, 30, 3165, 65, 35, 35 UK, 40, 50, MH50. (Item #: 173676, Ref: 180809M2) $5.20

Clutch

No
Picture
Clutch Alignment Tool - Dual Stage Clutch Alignment Tool with 1 1/8 inch by 10 splines and 1 5/8 inch by 25 splines. For tractor models 133, 135, 140, 148, 150, 152, 155, 158, 165, 168, 175, 175UK, 178UK, 180, 20, 20C, 20D, 20E, 20F, 2135, 230, 231, 235, 240P, 240S, 245, 253, 255, 261, 263, 265, 265S, 270, 271, 271X, 271XE, 275, 281, 281X, 281XE, 282, 283, 285, 285S, 290UK, 30, 30E, 3165, 35, 40E, 383, 390, 481, 670, 690, 50, 65, 97, TO35. (Item #: 119890, Ref: 1212-5955) $16.90

Clutch Kit, 11 inch, Fine Spline - Our new 11 inch complete clutch kit contains: 11 inch, 25 spline, 1.625 inch hub, standard spring, double pressure plate (532319M91). 11 inch 10 spline, rigid drive disc (516068M93). 9 inch 1 3/4 inch hub PTO disc. Pilot bearing measuring 1.57 inches outside diameter, 0.669 inch inside diameter, 0.472 inch width (832960M3). Release bearing measuring 4.06 inches outside diameter, 2.49 inches inside diameter and 0.870 inch width (892862M2). Clutch alignment tool. For tractor models 135, 150, 165, 175, 175 U.K., 178 U.K., 180, 20, 20C, 2135, 235, 245, 255, 265, 30, 3165, 35, 50, 65, 97, TO35. (Item #: 111060, Ref: 1212-1420) $290.00

Clutch Release Carrier Fork Locking Screw - This Clutch Release Carrier Fork Locking Screw is used to secure the release fork to the shaft on many Massey Ferguson models. Two used per tractor. Sold individually. It replaces Massey numbers: 881114M1, 881144M1, 881144M2, 3771408M1, 3790757M1, 180002M1 (Item #: 182943, Ref: 881144M1) $5.50

PTO Disc, 9 Inch - 10 spline on 1.750 inch hub. For tractor models 135 dual, 165 dual, 175 dual, 180, 20 dual, 202 dual, 203 dual, 204, 2135 dual, 2165 dual, 2200 dual, 30, 302 dual, 30B dual, 3165 dual, 35 dual, 50, 65, F40 dual, TO35 dual. Replaces 1753753M91, 1753753M92, 1753753M93, 1753753M94, 3620411M91, 3620411V91 (Item #: 113815, Ref: 1753753M94) $40.70

PTO Disc, 9.055 - 9.055 inch rigid disc, organic, spline diameter 1.75 inch 10 spline. For tractor models 130, 135, 165, 175, 180, 20, 202, 203, 2135, 2165, 2200, 245, 25, 255, 265, 290, 30, 302, 30B, 30D, 3165, 35, 40B, 50 serial number 515396 and up, 65, TO35 serial number 177395-177519 and 177538 and above. All with dual clutches. Replaces 1034195M1, 1539020C1, 1753753M1, 1753753M94, 1753753M94-A, 181102M92, 1851652M92, 323022046, 323022047, 3620411-RF, 3620411-RO, 3620411M1, 3620411M91, 392492R91, 709640R92, 899823M91. (Item #: 163114, Ref: 323022047) $52.00

Pilot Bearing - Clutch pilot bearing, heavy-duty, long lasting stainless steel. Bore: 0.670 inches (17mm), OD: 1.57 inches (39.88mm), 0.470 inches width. For tractors: MF50, MF65, MF85, MF88, MF235, MF245, MF255, MF285, MF1080 industrials: 20, 20C, 30, 30B, 31, 35 utility and turf, 40, 40B, 50, 50A, 50C, 202, 203, 204, 205, 302, 304, 2135, 2200. Replaces 832953M3, 1440487X1, 828123M1, 828123M2, 832960M3 (Item #: 107933, Ref: C5NN7600A) $3.40

Pilot Bearing - This Pilot Bearing measures .669 inches inside diameter, 1.575 inches outside diameter and is .472 inches wide. For tractor models 285, 290, 298, 30, 302, 30B, 30D, 30E, 30H, 31, 3165, 340, 342, 35, 350, 352, 355, 360, 362, 365, 375, 382, 390, 390T, 398, 399, 40, 40B, 40D, 40E, MH44, 50, MH50, 500, 50A, 50B, 50C, 50D, 50E, 50EX, 50H, 50HX, 560, 565, 575, 590, 592, 595, 60H, 65, 670, 675, 690, 698, 698T, 699, 85, 88, F40, FE35, Super 90, TE20. Replaces OEM part number 828123M2. (Item #: 107933, Ref: C5NN7600A) $3.40

Release Bearing - Bearing, clutch release, 2.49 inch inside diameter, 4.10 inch outside diameter, 1.5265 inches wide. For single clutch tractors: TO35, MF35, F40, MF50, MF65, MF135 industrials: 2135, 3165. (A2336-37/A2336-147) For 2135, 3165, F40, MF135, MF35, MF50, MF65, TO35, 202, 203, 302, 304. Replaces 833085M1, 833085, 180505M2, N2336-147 (Item #: 168448, Ref: 833085M2) $173.94

Release Bearing Carrier - Carrier, for clutch release bearing. Carrier bore 2.130 inch (2-1/8 inch approximate); outside diameter 2.503 inch (2-1/2 inch). PLEASE CHECK CARRIER BORE BEFORE ORDERING. For single or dual clutch. Tractors: TO35, MF35, MF50, MF65. Industrials: 20, 202, 203, 302, 2135. Use with bearing 892862M2 for DUAL CLUTCH ONLY. This is the old style for retainers with bronze bushing. (Item #: 165363, Ref: 183129M2) $24.10

Cooling System

Thermostat - Thermostat. For Continental Gas Equipped tractors: 2200, 202, 204, 2135, 3165, F40, TO35, 50, 2500, 302, 304, 356, 135, 150, 165, 175, 180, 35, 65, 35, Colt, MH21, MH20, MH22, MH50. 160 degree. Comes with gasket. Replaces 830842M91, 836000V91, 836000M1, 830842M91, 830685M91, 184406V2, 181566M1 (Item #: 108422, Ref: 836000M91) $13.80

Decals and Emblems

Emblem - For tractor models FE35, 3165, FE135 COVENTRY. (Item #: 104149, Ref: 883645M1) $21.90

Drive Train

Axle Housing Shim .004 - This Axle Housing Shim measures .004 inches thick, inside diameter of 4 1/2 inches and outside diameter of 7 1/2 inches. For 12 bolt housings on models: FE135, FE35, F40, TO35, 135, 150, 230, 231, 235, 240, 240P. Instrials: 20, 20C, 20D, 202, 204, 2135, 2200, 30, 3165. (Item #: 172917, Ref: 183259M1) $4.10

Axle Housing Shim .016 - .016 inch thick shim. 12 bolt. For tractor models FE135, FE35, F40, TO35, 135, 150, 230, 231, 235, 240, 240P. Instrials: 20, 20C, 20D, 202, 204, 2135, 2200, 30, 3165. (Item #: 173664, Ref: 183260M1) $3.90

Axle Shim - This is a Steel Rear Axle Shim. It is .020 inches thick. It is used on Ferguson TEA20, TE20, TEF20, TO20, TO30, TO35, F40, Massey Harris 50, Massey Ferguson 35, 35 UK, 50, 135, 135 UK, 150, 230, 231, 235, 240, 245, 3165, 20, 202, 204, 2135, 20C, 20D, 30. It replaces original part number 183261M1. (Item #: 178176, Ref: 183261M1) $3.80

Bearing Cup, Differential - For tractor models FE35, TE20, TO20, TO30, 135, 150, 165, 175, 180, 20, 20C, 20D, 20F, 202, 203, 204, 205, 2135, 2200, 230, 231, 235, 24, 240, 240P, 245, 25, 250, 2500, 253, 255, 265, 270, 275, 282, 285, 30, 30B, 30D, 30E, 30H, 302, 31, 3165, 356, 360, 362, 3630, 3650, 375, 383, 390, 390T, 399, 40, 40B, 40E, 4500, 50, 50A, 50C, 50D, 50E, 50H, 60, 60H, 60HT, 65, 6500, 670, TO35 serial number <-169467. Replaces 1850090M91. (Item #: 117943, Ref: 185778M1) $30.10

Bearing Kit - Needle Bearing Kit. For transmission reverse idler gear. Not for shuttle, instant reverse, or 12-speed transmissions. (1) required. For tractors: TO35 serial number 171549 and up, MF35, MH50, MF50, MF65, MF135, MF150, MF165, MF175, MF180, MF230, MF231, MF235, MF240. (Item #: 125327, Ref: 830735M91) $34.00

Bearing Seal and Collar Kit, Rear Axle - Contains (1) shrink-on collar 180596M1 (3 inch x 2-1/4 inch x 11/16 inch), (1) axle bearing (cup 300975M1 and cone 195675M1), (1) inner axle seal 195678M2 (2-1/8 inch x 2-7/8 inch x 1/2 inch), (1) outer axle seal 195677M1 (2-3/4 inch x 3-5/8 inch x 19/32 inch). Fits where the above parts are used: TO35, F40, 133, 135, 135UK, 140, 148, 150, 20, 20C, 20D, 2135, 230, 231, 235, 240, 245, 30, 3 165, 340, 35, 35UK, 35X, 50, 550. Verify part numbers. Some of these models were build with more than one rear axle. (Item #: 182552, Ref: S.05948) $105.00

Bearing, Needle - Needle Bearing for countershaft. For 1080, 1085, 1200, 1250, 133, 135, 140, 145, 148, 150, 152, 158, 165, 168, 175, 178, 180, 185, 188, 20, 20C, 20D, 20E, 20F, 2135, 230, 231, 235, 240, 245, 250, 253, 255, 260, 261, 263, 265, 265 S (TR), 270, 275, 282, 283, 283 Brazilian, 285 (FR), 285 S (TR), 285 US Built, 290, 298, 30, 30B, 30D, 30E, 30H, 31, 3165, 340, 342, 35, 350, 352, 355, 35X, 360, 362, 365, 375, 375E Brazilian, 383, 390, 390E Brazilian, 390T, 393, 396, 398, 399, 40, 40B, 40E, 40H, 415 Brazilian, 4215, 4220, 4225, 4235, 4245, 425 Brazilian, 4255, 4260, 4265, 4270, 4315, 4325, 4335, 4345, 435 Brazilian, 4355, 4360, 4365, 4370, 440 Brazilian, 445 Brazilian, 475 Brazilian, 481 Brazilian, 50, 50B, 50C, 50D, 50E, 50EX, 50H, 50HX, 5340 Brazilian, 5355 Brazilian, 5360 Brazilian, 5365 Brazilian, 550, 560, 565, 575, 590, 592, 595, 60H, 60HX, 65, 65 US Built, 670, 675, 690, 698, 698T, 699, 765, 835, 865, Super 90, TO35, Massey Harris 50. Replaces 532883M1, 195453M1 (Item #: 167261, Ref: 195453M1) $10.60

Countershaft - Countershaft, 6 speed transmission. 20/17/10 spline, 15 tooth, 12.750 inches long. For the following tractors: 135, 202, 203, 204, 205, 2135, 2200, 3165 35, 50, 65, FE135, MH50, TO35. (Item #: 173663, Ref: 183085M1) $194.41

Differential Lock Cap. - 10 lug. For tractor models FE35, 135, 150, 20, 20C, 20D, 202, 204, 2135, 2200, 230, 231, 235, 240, 240P, 245, 30, 3165, 35, 50, FE135. (Item #: 172279, Ref: 190963M1) $93.00

Differential Lock, Cam and Shaft Assembly - For tractor models 135, 150, 20, 202, 204, 20C, 20D, 2135, 2200, 230, 231, 235, 240, 240P, 245, 30, 3165, 35, 50, FE135, FE35. (Item #: 173127, Ref: 190960M92) $56.00

Differential Planetary Thrust Washer - Used on many Ferguson and Massey Ferguson models, this washer measures 3 inches inside diameter, 4 3/16 outside diameter and 0.053 inches thick. Used on 1080, 1100, 1105, 1130, 1135, 1150, 1155, 1200, 1250, 133, 135, 140, 148, 150, 152, 155, 158, 165, 168, 175, 178, 180, 185, 188, 20C, 20D, 20F, 2135, 230, 240, 250, 2620, 2640, 265, 2680, 2720, 275, 285, 290, 298, 30B, 30D, 3165, 340, 342, 35, 350, 352, 355, 360, 362, 372, 375, 382, 390, 390T, 398, 399, 50, 550, 565, 575, 590, 595, 65, 675, 690, 698, 698T, 699, 85, 88, Super 90, TE20, TEA20, TED20, TEF20, TO20 Replaces OEM number 181247M1. (Item #: 173021, Ref: 181247M1) $11.20

Differential Ring and Pinion Set - 9-7/8 inch Pinion Gear length. Differential, ring gear and pinion set. 37 and 6 tooth. For tractor models 30, FE35, TO35, 35, 35UK, 50, 135, 135UK, 230, 231, 235, 240, 245, 20, 20C, 20D, 2135, (3165 light duty) check pinion length. Replaces 1683757M91, 182115M91, 1885317M91, 1885317M92. (Item #: 116129, Ref: 531862M91) $306.00

Gasket, Rear Axle Trumpet Housing - Size is approximately 15-1/4 inches. Fits TEA20, TO20, TO30, TO35, 135, 150, 165, 175, 180, 20, 20C, 20D, 2135, 2200, 230, 231, 235, 240, 240P, 245, 2500, 30, 31, 3165, 35, 40, 50, 50, 65. (Item #: 151916, Ref: 183254M1) $4.40

Gear Lever Tension Spring - This Gear Lever Tension Spring is widely used on many Massey Ferguson Tractors. Confirm part number before ordering. Replaces 192007M1, 964894M1, 180582M1 (Item #: 126830, Ref: 180582M1) $2.40

No
Picture
Gear Shift Knob - Round ball, 3/8 inch NF thread. For tractor models TO20, TE20, TEA20, TEF20, TO30, TO35, FE35, F40, 130, 135, 150, 165, 175, 20, 202, 203, 204, 205, 2135, 220, 2200, 2500, 30, 302, 303, 304, 30E, 3165, 320, 333, 35, 356, 40, 404, 406, 44, 444, 50, 50A, 50E, 555, 65, 85, 88, 90, Super 90, 95, 98, F40, FE135, MH50, TO35. (Item #: 150683, Ref: 180006M91) $3.90

Gear Shift Spring Retainer - This Gear Shift Spring Retainer is used on many Massey Ferguson Models. Replaces OEM numbers 180583M1, 1861024M1 (Item #: 126687, Ref: 1861024M1) $13.30

Gear, 1st - This gear is 1st gear for 8 speed transmission. Replaces 520700M1, 183042M1. Gear has 44 teeth and is a 18 spline. For tractor models FE35, 1080, 1085, 135, 150, 165, 175, 180, 20, 20C, 20D, 203, 2135, 2200, 230, 235, 240, 245, 250, 253, 255, 265, 270, 275, 283, 285, 290, 298, 30, 30B, 30D, 31, 3165, 360, 362, 375, 383, 390, 390T, 40, 40B, 50, 50C, 50D, 50E, 65, (20F, 40E, 50H ALL UK MODELS), 35 GAS/DIESEL, 282 MEX. (Item #: 151828, Ref: 1682688M1) $80.00

Gear, 2nd - This gear is 2nd speed for 8 speed transmission. Gear has 23 teeth. For tractor models FE135, FE35, F40, MH50, TO35, 1080, 1085, 11, 165, 148, 150, 155, 158, 165, 168, 175, 178, 185, 188, 20, 20C, 20D, 20F, 202, 204, 205, 2135, 2200, 230, 231, 235, 240, 240P, 245, 250, 253, 255, 262, 265, 270, 275, 282, 283, 285, 290, 298, 30, 304, 31, 3165, 35, 360, 375, 383, 390, 390T, 40, 40B, 40E, 50, 50C, 50D, 50E, 550, 565, 575, 590, 65, 765. (Item #: 173295, Ref: 180419M1) $25.90

Gear, 3rd - This gear is 3rd speed for, 8 speed transmission. Gear has 33 teeth, 17 spline and is 5.075 inches in diameter. For tractor models FE35, MH50, TO35, 1080, 1085, 135, 148, 150, 155, 158, 165, 168, 175, 178, 180, 185, 188, 20, 20C, 20D, 20E, 202, 203, 204, 205, 2200, 230, 231, 235, 240, 240P, 245, 250, 253, 255, 265, 270, 275, 283, 285, 290, 298, 30, 304, 31, 3165, 35, 360, 362, 375, 383, 390, 390T, 40, 40B, 40E, 50, 50C, 50D, 50E, 50H, 550, 565, 575, 590, 65, 765, FE135 COVENTRY, 2135 TURF UTIL NARROW. (Item #: 151824, Ref: 180415M1) $30.10

Gear, Reverse - For tractor models FE35, 1080, 1085, 135, 148, 150, 155, 158, 165, 168, 175, 178, 180, 185, 188, 20, 20C, 20D, 20F, 202, 203, 204, 205, 2200, 230, 231, 235, 240, 240P, 245, 250, 253, 255, 265, 270, 275, 282, 283, 285, 290, 298, 30, 304, 31, 3165, 35, 360, 362, 365, 375, 383, 390, 390T, 40, 40B, 40E, 50, 50C, 50D, 50E, 50H, 550, 565, 575, 65, 765, FE135 COVENTRY, TO35 serial number 17159>, 2135 TURF UTILITY NARROW. This gear is for a 8 speed transmission with 13 and 21 teeth. (Item #: 151823, Ref: 183040M1) $75.00

Input Housing Shaft Seal - 1-1/8 inch inside diameter x 2-1/4 inch outside diameter. For tractor models (TO35, FE35 with single clutch), 135, 135 UK, 2135, 240, 3165, 65, MF35, MF50. (Item #: 178027, Ref: 195523M1) $4.80

Input Shaft Housing Gasket - For tractor models F40, FE35, TO35, 135, 135 UK, 2135, 240, 3165, 65, MF35, MF50, MH50. (Item #: 166860, Ref: 180434M1) $1.40

Lock Nut, Pinion - Used on Massey Ferguson 133, 135, 140, 148, 165, 175, 178, 180, 20, 20C, 2135, 2200, 230, 235, 245, 2500, 255, 265, 275, 30, 31, 3165, 35, 35UK, 40, 4500, 50, 50A, 65, 6500. (Item #: 179636, Ref: 180456M1) $27.27

Main Drive Pinion Shaft Seal - Measures 1.125 inch x 1.562 inch x .250 inch. For tractor models 20, 20C, 202, 203, 2135, 30, 31, 3165, TO35, 135, 150, 165, 175, 230, 235, 245, 35, 50, 65. Replaces: 195501M1, 195870M1. (Item #: 165141, Ref: 195501M1) $4.70

Mainshaft - 11.360 inches long. For tractor models (135, 150, 165, 202, 203, 2135, 3165 all with 6 speed transmission and narrow 1.560 inch planetary gear), (202 early production with standard transmission), (203 serial number up to 659001340 with standard transmission), (35 serial number CN13556 and up with standard transmission), (50, 65 all serial number CN13566 and up with regular transmission), (FE35 serial number 213314 and up with regular transmission). (Item #: 172289, Ref: 187168M1) $149.00

Oil Trough Assembly, LH - For tractor models F40, FE135, FE35, 50, TO35, 150, 20, 202, 204, 20C, 20D, 2035, 2200, 230, 231, 235, 240, 240P, 245, 30, 3165, 35, 50. Replaces 4246537M1, 825774M2, 825774M2 (Item #: 173161, Ref: 825774M2) $44.00

Pinion Nut Washer - Used on Massey Ferguson models: 133, 135, 140, 145, 148, 152, 155, 158, 165, 168, 175, 178, 180, 185, 188, 20, 20C, 2135, 2200, 230, 235, 245, 2500, 255, 265, 275, 30, 31, 3165, 35, FE35, 40, 4500, 50, 50A, 65, 6500, 765, 865 (Item #: 183834, Ref: 180455M1) $2.51

Planetary Cover Plate, Front - For the following tractors: 1080, 1085, 135, 150, 165, 175, 180, 20, 202, 203, 204, 205, 2135, 2200, 230, 231, 235, 240, 240P, 245, 250, 253, 255, 265, 270, 275, 282, 283, 285, 290, 298, 30, 302, 304, 30B, 30D, 30E, 31, 35, 360, 362, 375, 383, 390, 390T, 393, 40, 50, F40, FE135 COVENTRY, FE35, MH50, TO35, Industrial: 20C, 20D, 20F, 2500, 3165, 40B, 40E, 4500, 50A, 50D, 50E, 60H, 60, 6500. Replaces 180408M2, 180408M1. (Item #: 173500, Ref: 180408M2) $17.30

Planetary Cover Plate, Rear - For the following tractors: 1080, 1085, 135, 150, 165, 175, 180, 20, 202, 203, 204, 205, 2135, 2200, 230, 231, 235, 240, 240P, 245, 250, 253, 255, 265, 270, 275, 282, 283, 285, 290, 298, 30, 302, 304, 30B, 30D, 30E, 31, 35, 360, 362, 375, 383, 390, 390T, 393, 40, 50, F40, FE135 COVENTRY, FE35, MH50, TO35, Industrial: 20C, 20D, 20F, 2500, 3165, 40B, 40E, 4500, 50A, 50D, 50E, 60H, 60, 6500. (Item #: 180666, Ref: 184012M4) $20.40

Planetary Selector Gearshift - For tractor models: 1080, 1085, 135, 150, 165, 175, 180, 20, 202, 203, 204, 205, 2135, 2200, 230, 231, 235, 240, 240P, 245, 250, 253, 255, 265, 270, 275, 282, 283, 285, 290, 298, 30, 302, 304, 30B, 30D, 30E, 31, 35, 360, 362, 375, 383, 390, 390T, 393, 40, 50, F40, FE135 COVENTRY, FE35, MH50, TO35, Industrial: 20C, 20D, 20F, 2500, 3165, 40B, 40E, 4500, 50A, 50D, 50E, 60H, 60, 6500. (Item #: 173169, Ref: 180446M1) $17.70

Planetary Thrust Washer - This Planetary Thrust Washer is for tractor models 135, 150, 165, 202, 203, 204, 205, 2135, 302, 304, 3165, 35, 356, 50, 65, 85, 88, Super 90, F40, FE35, TO35. (Item #: 172988, Ref: 180414M1) $16.10

Seal, Rear Axle Oil, Inner - This oil seal fits: [Industrial; as an inner rear axle shaft oil seal with dry brakes: 2135, 2200, 3165, MF20, MF20C, MF30 (2 used per tractor, sold individually)], as a transmission input shaft front cover oil seal: 85, 88, Super 90, [as an inner rear axle shaft oil seal with dry brakes: 135, 150, 202, 203, 204, 205, 230, 231, 235, 240, 245, 35, 50, F40, FE35, TO35 (2 used per tractor, sold individually)]; Replaces: 195678M1, 195678M2. 2.125 inches inside diameter, 2.879 inches outside diameter, 0.438 inches wide. (Item #: 108415, Ref: 195678M2) $6.10

Shift Fork, 1st, Reverse, 2nd and 3rd - For tractor models FE35, F40, MH50, TO35, 1080, 1085, 135, 150, 165, 175, 180, 20, 20C, 20D, 202, 203, 204, 205, 2135, 2200, 230, 235, 245, 255, 265, 270, 275, 285, 290, 298, 30, 31, 3165, 35, 50, 65. (Item #: 151023, Ref: 180437M1) $38.00

Shift Lever Locking Pin - This Shift Lever Locking Pin is used on Ferguson, Massey Harris and Massey Ferguson applications. It replaces OEM part numbers 180581M2, 1678440M1, 180581M1 (Item #: 183009, Ref: 1678440M1) $1.10

Side Cover Gasket - This Side Cover Gasket fits the multiple Ferguson and Massey Ferguson tractor models as a side cover gasket and a PTO shift cover gasket. It replaces original part numbers 181217M3, 181217M1, 181217M2, 181217M4, 181217M5, 181217M6, 3816331M92, 181217V3, 3816331T92. (Item #: 112236, Ref: 9N4131) $1.10

Snap Ring - Internal - For Massey Ferguson tractor models TO35, 20, 30, 31, 35, 50, 135, 150, 165, 175, 178, 230, 235, 240, 245, 2135, 3165, Compatible with Massey Ferguson Construction and industrial models 20C, 30, 31, 40, 50, 50B, 65, Replaces Massey Ferguson OEM number 195222M1, (Item #: 169491) $3.30

Transmission Rear Axle Gasket - This gasket is used on multiple Massey Ferguson tractors. Dimensions measure 10.750 inches X 16 inches. It replaces original part numbers 1861986M1, 1861986M2, 3599804M1, 3599804M2, 3599804V2, 8884457M1, 181363M1, 521181M1, VPH1405 (Item #: 111906, Ref: 1861986M1) $7.80

Electrical System

Alternator with Tach Drive - This is a 12 volt 63 amp alternator. It is internally regulated and comes with fan and pulley. This alternator can be used to replace original generator. Additional brackets and hardware may be needed. Tach drive is appropriate for gas tractors where the tach drive is on the generator. Use part number ADR9209 to make this a single wire self exciting alternator (not included). (Item #: 164228, Ref: ADR0382) $140.00

Fuse Holder - Mounts in 5/8 inch diameter hole. 2 spade connectors. Replaces: 186216M91, 186216M91, 506063M91, 522462M91 (Item #: 112273, Ref: 376852R91) $10.40

Neutral Safety Switch - This Neutral Safety Switch is for bullet type terminal. Replaces 181140V94, 53208520, 181140M1, 181140M91, 181140M94, 181140M93, 181140M92. (Item #: 111507, Ref: 181140M94) $11.80

Voltage Regulator, 12 Volt - 12 Volt - 4 Terminal - Flat Mount. 4 Terminal: Light - Battery - Field - Armature (underneath base). Fits TO35, MF25, F40, MF35, MF50, MF65, MF85, MF88, MF Super 90, MF135, MF150, MF165, MF175, MF180, MF202, MF204, MF203, MF205, MF2135, MF3165. Combines SP300, SP410, SP510. 12 Volt models with generators. The Three Post side of this regulator may be parallel or slightly splayed. (Item #: 105581, Ref: 182548M92) $26.50

Engine Bearings

Thrust Washer Set - 4 Pieces - FOR AD3.152 Perkins Gas and Diesel. With engine serial number less than 2820092. (Item #: 107167, Ref: 31137211_21) $6.90

Thrust Washer Set - 4 Pieces - Tabbed. Fits 152 CID 3 cylinder, 203 CID 4 cylinder gas or diesel engines. For tractor models 2500, 20, 40, MF135, MF150, 203, 205, 35, FE35, MF35, MF50, 200, 2244, 2200, 2500, MF235, 200B, 4500, MF230, 20C, 30B, MF245, MF250, 356, MF65, 300, 302, 304, 3165, MF165, 40B, 50.735113M1 (Item #: 107167, Ref: 31137211_21) $6.90

Engine Gaskets

Crankshaft Seal, Rear Rope Type, Perkins - Sold individually - requires 2. Fits 152 CID 3 cylinder, 203 CID 4 cylinder gas or diesel engines. For tractor models 2500, 20, 40, MF135, MF150, 203, 205, 35, FE35, MF35, MF50, 200, 2244, 2200, 2500, 2135, MF235, 200B, 4500, MF230, 20C, 30B, MF245, 356, MF65, 300, 302, 304, 3165, MF165, 30, 40B, 50, MF255. (Item #: 107228, Ref: 735866M1) $2.60

Crankshaft seal, Front Lip Type, Perkins - Fits 152 CID 3 cylinder or 203 CID 4 cylinder gas or diesel engines. For tractor models 2500, 20, 40, MF135, MF150, 203 and 205 to serial number 659002115, 35, FE35, MF35, MF50, 2135, MF235 engine serial number ending in D, 200B, 4500, MF230, 20C, 30B, MF245, MF250, 356, MF65, 300, 302, 304, 3165, 40B, 50, MF165, MF255. (Item #: 107221, Ref: 1851747M1) $9.40

Engine Rebuild Kits

Engine Parts

Valve Spring Retainer, Perkins Diesel - Fits 152 CID and 203 CID perkins engines. For tractor models 203, 205, 35, FE35, MF35, MF50, 200, 2244, 2200, 2500, MF235, 200B, 4500, MF230, 20C, 30B, MF245, MF250, 356, MF65, 300, 302, 304, 3165, MF165, 40B, 50. Price shown is for each, sold only in multiples of 2 items. (Note: 2 halves = 1 retainer) (Item #: 180600, Ref: 731959M1) $5.00

Engine Pistons and Sleeves

Piston Sleeve, Perkins 152 and 203 Gas or Diesel - Sleeve, CAST, replacing original CAST sleeve 734175M1, flange thickness .150 inch. Fits 152 CID 3 Cylinder and 203 CID 4 Cylinder Gas or Diesel Engines 3.6 inch standard bore. For tractor models 2500, 20, 40, MF135, MF150, 35, 203, 205, FE35, MF35, MF50, 200, 2244, 2200, 2135, MF235, 200B, 4500, MF230, 20C, 30B, MF245, MF250, 356, MF65, 300, 302, 304, 3165, MF165, MF255, 40B, 50. (Item #: 128601, Ref: 739043M1) $22.50

Sleeve Seals, Pack of 2 - Pack of 2. O-ring for Piston Liner Sleeve. (NOTE: Sleeves usually use a minimum of 2 O-rings each). Use on Ferguson, Massey Harris and Massey Ferguson tractors with Z120, Z129, Z134, Z145, and G176 engines. Replaces 1750000M1 (Item #: 128575, Ref: 1750000M1) $9.10

Engine Rings

No
Picture
Piston Ring Set, 1 Cylinder, Perkins 152 or 203 Diesel - 152 or 203 CID diesel engine standard bore 3.6 inch. Ring set, for 1 piston, used with CAST sleeves only. For 20, 200, 200B, 203, 205, 2135, 2200, 2244, 2500, 30, 300, 302, 304, 3165, 35, 356, 40, 40B, 4500, 50, FE35, MF135, MF150, MF165, MF230, MF235, MF250, MF255, MF35, MF50, MF65, Super 92. Set includes 2 at 3/32 inch, 1 at 1/8 inch, 2 at 1/4 inch. (Item #: 120667, Ref: 836325M91) $12.90

Exhaust System

Fuel System / Air Intake

Fuel Cap, Vented - Fuel Cap INTERNAL LOCK TANGS 2.7 inch OD, 1.78 inch overall tab length, 0.250 inch tab width. This silver cap is for models: Pony, Pacer, TE20, TO20, TO30, 35, F40, 50, 65, 85, 88, 90, 135, 150, 165, 175, 1080, 1100, 1130, 1150, 1500, 1800, 202, 203, 204, 205, 302, 304, 356, 2135, 3165. Replaces 850493M1, YTO 520948M91. Verify OEM number to ensure fit. (Item #: 184806) $10.00

Gauges

Proofmeter Drive Assembly - For a DELCO Alternators and Generators. This improved design uses a steel drive gear (originals used a fiber gear). Proofmeter Drive Assembly mounts on original type generator. Fits TO20, TO30, TO35, 35, 50, 65, 85, 88, Super 90, 135, 150, 175, 180, 1080, 1100, Industrials: 30, 31, 35 Turf and Utility, 50, 2135, 2200, 2500, 3165, 202, 204. ALL GAS ENGINES. Includes housing, 2 drive gears and gaskets. 7/8 - 18 threads. Does NOT include cable. (Item #: 113771, Ref: 1751295M91) $26.70

Tachometer Cable - Tachometer Cable Assembly, 39 inch. Vinyl covered. It has a 7/8 Inch drive end and a 5/8 inch load end. For tractors: TO35 gas, MF35 gas, MH50 gas, MF50 gas, MF135 Continental Gas, MF150 Continental Gas, MF165 gas, MF175 Industrials: 30 gas, 35 gas utility and turf, 202, 204, 2135 gas, 3165 Continental Gas. Replaces: 1751284M91, 506331M91, 506334M91, 521596M91, 532426M92 (Item #: 121217, Ref: 506331M91) $18.20

Water Temperature Gauge - This temperature gauge has a 72 inch Capillary tube, 2 inch Face Diameter, Chrome Ring. 180 degree normal temperature setting, 220 degree pegs top end. 5/8 inch UNF connector. TO20, TO30, TO35, FE35, F40, MH44, 50, 333, 444, 555, MF35, 50, 65, 85, 88, Super 90, 135, 165, 175, 178; ind. 20, 30, 31, 40, 50A, 70, 80, 202 Work Bull, 2200, 3165. Replaces: 1078125M91, 1079390M91, 180727M91, 180727M93, 182652M92, 1850512M94, 881396M91, 899455M91, 108727M93, 1078125M91, 0236708, 1078125M91, 180727M91, 180727M92, 180727M93, 881369M91, 899455M91 (Item #: 104116, Ref: 180727M91) $25.30

Hitch / Drawbar

Crank Arm, Leveling Box - This Leveling Box Crank Arm is for tractor models TE20, TEA20, TO20, TO30, TO35, 20, 31, 35 (France), 35, 35X (France), 40, 50, 65, 130 (France), 135 (UK), 135, 150, 165 (UK), 165, 175 (UK), 175, 178 (UK), 180, 205, 230, 231, 231S, 235, 240 (S, Turkey), 240, 240P, 241, 245, 250, 253, 255, 261, 263, 265, 265S (S, Turkey), 270, 271, 275 (UK), 275, 281, 282, 283 (UK), 283, 285S (S, Turkey), 290 (UK), 290, 298, 302, 304, 360, 362, 365 (s/n: B18009-earlier), 375, 383, 390, 390T, 393, 394S (s/n: D03066-earlier), 396, 398, 399, 698, 2135, 2200, 3050, 3060, 3065, 3070, 3090, 3095, 3125 (France), 3125, 3140, 3165, 20, 20C, 20D, 20E, 20F, 30, 30B, 30D, 30E, 40B, 40E, 50C, 50D, 50E, 202. Replaces Replaces 81822432, 81717231, C5NN594E, 957E594, 888607M1, 1662382M1, 181349M1 (Item #: 172986, Ref: C5NN594E) $9.10

Drawbar, Straight - For tractor models TO35, 135, 150, 165, 20, 30, 3165, 35, 50, 65. This drawbar is 35 3/4 inches OVERALL LENGTH, 2 inches WIDE, 1 1/8 inches THICK. (Item #: 160846, Ref: 184611M1) $58.00

Leveling Box Fork - A=5/8 inch, B= 3/4 inch, C= 11/16 inch, D=14-3/16 inch. For tractors: TE20, TO20, TO30, TO35, FE35, F40, MF35, MF135, MF150, MF65 (used in standard right hand assembly with 10-1/2 inch shaft), also left hand on MF65. (Item #: 110971, Ref: 184358M1) $28.50

Leveling Box Gear Housing - For tractor models 135, 148, 150, 165, 175, 20, 202, 203, 204, 205, 20C, 20D, 20F, 2135, 2200, 230, 231, 235, 240, 240P, 245, 25, 250, 255, 265, 275, 285, 30, 302, 304, 30B, 30D, 30E, 3165, 35, 40, 40B, 40E, 50, 65, 765, F40, FE135, FE35, TE20, TEA20, TO35. (Item #: 182821, Ref: 193181M1) $21.00

Leveling Rod, Left Hand - For TO35, 35, F40, MH50, 50, 135, 150, Ind: 202, 204, 2135, 3165. Lift Link, left hand, non-adjustable. Hole centers approximately 20 inches. Replaces 182544M92, 182554M92, 182544M92, 1884720M1, 897661M1, 897661V1. (Item #: 111007, Ref: 182544M92) $44.30

Low Link Pivot - Pivot Shaft for lower link. Threaded ends 5/8 inch NF and 5/8 inch NF, overall length 5-1/4 inches. For tractors: TO20, TO30, TO35, MF35, MF135, MF150 industrials: 2135, 3165, 202, 204. MF1130. Replaces 181229M2, 181229M1, 181229M4, 181229M5 (Item #: 166280, Ref: 181229M5) $14.30

Pin - Pivot Pin. For swinging drawbar. 1 inch outside diameter by 1-7/8 inch working length. Not for swinging drawbar kit SDA6 which requires part number Pt3, 7/8 inch diameter pin. Fits original swinging drawbar 184611M1. For tractors: TO35, MF35, MH50, MF50, MF65, MF135, MF150, MF165, MF230, MF235, MF245, MF255 industrials: MF20C, MF30B, MF40B, MF3165. For MF165, MF65. (Item #: 155129, Ref: 184630M1) $7.70

Rocker Link - For tractor models 135, 150, 165, 20, 203, 205, 20C, 2135, 2200, 230, 245, 30, 302, 304, 3165, 40, 50, F40, FE35. (Item #: 165755, Ref: 180973M2) $22.40

Hydraulic System

Draft Control Boot - Draft Spring Rubber Boot. Fits Multiple Massey Ferguson Models. Replaces 1660439M1, 887654M1, 887654M2. (Item #: 169245, Ref: 887654M1) $3.10

Draft Control Plunger Spring - For tractor models 1080, 135, 150, 165, 175, 180, 202, 205, 20C, 20F, 2135, 230, 231, 235, 240, 245, 250, 253, 255, 265, 270, 275, 282, 283, 285, 30, 302, 304, 30B, 30E, 3165, 35, 360, 362, 375, 392, 40, 40B, 40E, 50C, 50D, 50E, 65, 670, F40, MH50, TO35, TO30, TO20, TE20. Hydraulic Spring. Replaces 182582V1, 180998M1, 182582M1, 182582M1 (Item #: 165989, Ref: 9N547B) $35.30

Draft Control Seat - This Draft Control Spring Seat is used on many Ferguson, Massey Ferguson and Massey Harris tractors. 1.780 inch inside diameter. It replaces OEM numbers: 719011M1, 182581M1, 886351M1, 889346M2, 886351M2 (Item #: 174656, Ref: 182581M1) $15.00

Hydraulic Diverter Valve - Hydraulic Diverter Valve made for 1080, 1085, 130, 135, 150, 165, 175, 180, 20, 202, 203, 204, 205, 20C, 20D, 20F, 2135, 2200, 230, 231, 235, 240, 245, 25, 250, 253, 255, 265, 270, 275, 282, 283, 285, 290, 30, 302, 304, 30B, 30D, 30E, 31, 3165, 35, 360, 362, 375, 383, 390, 392S, 393, 398, 40, 0B, 40E, 50, 50C, 50D, 50E, 65, 85, MH50, TO35 ALL WITH 3/8 inch NPT ports. Verify the diagonal bolt pattern of the part in the picture as this only fits in place of existing cover plate (180908M1 or 182373M91). Hydraulic supply continues available for lift arms, or two additional ports are available along with a return to tank. Only one supply can be selected at a time with hydraulics isolated in other positions. (Item #: 161564, Ref: S.60032) $116.00

Hydraulic Filter Kit - This Kit contains 521451M1 filter, 185839M91 cap and 185555M1 bowl. It is used on Massey Ferguson models: 1080, 135, 145, 148, 150, 165, 168, 175, 178, 180, 185, 188, 20, 2135, 245, 30, 31, 3165, 35, 35X, 40, 50, 65, FE35 (Item #: 184914, Ref: 185839M92) $28.80

Hydraulic Lever, Tension Bolt and Spring Kit - This Hydraulic Lever, Tension Bolt and Spring Kit is used on multiple Massey Ferguson Models. Replaces: 181041M1, 961469M1, 961369M1. (Item #: 173300, Ref: 181041M1) $2.70

Hydraulic Pump Filter O-ring - This O-Ring is used with 185555M1 cap and Bowl Set. (Item #: 178156, Ref: 831907M1) $0.50

Hydraulic Stand Pipe O-Ring - This Hydraulic Stand Pipe O-Ring measures 3/8 inch inside diameter, 1/2 inch outside diameter, 1/16 width. Two are used per stand pipe. Replaces Massey Ferguson part number 195561M1 (Item #: 124228, Ref: 195561M1) $0.50

Hydraulic Stand Pipe Spiral Back Up Ring - This Hydraulic Stand Pipe Spiral Back Up Ring is used on many Massey Ferguson Models. Two are used per stand pipe. Sold individually. Replace part number 195874M1 (Item #: 124229, Ref: 195874M1) $2.00

Lift Clevis - This lift clevis, has on the inside of the yoke, a multi-level face. If you need a smooth face on the inside of the yoke, this is not the correct part and we do not have what you need available. For tractor models 135UK, 165, 180, 20, 203, 205, 20C, 2135, 2200, 230, 235, 245, 30, 302, 304, 31, 3165, 35, 40, 50, F40, MH50, TO35. Hydraulic Lift Clevis. (Item #: 173304, Ref: 180972M2) $29.40

Lift Clevis Bushing RH - Right hand slotted bushing for rocker on draft control clevis. For 135, 165, 175, 180, 20, 202, 203, 204, 205, 2135, 230, 245, 30, 302, 304, 31, 3165, 35, 40, 50, 65, F40, FE35, MH50, TO35. Replaces 181982M1, 180974M1 (Item #: 153600, Ref: 181982M1) $6.50

Lift Clevis Bushing, LH - Left hand slotted bushing for rocker on draft control clevis. For 135, 150, 165, 165UK, 175, 175UK, 185UK, 180, 20, 200, 202, 203, 204, 205, 20C, 20D, 2135, 2200, 230, 235, 240, 240S, 245, 265S, 271, 281, 285S, 30, 302, 304, 31, 3165, 35, 40, 50, 65, FE35, MH50, TO35. (Item #: 153601, Ref: 180974M1) $6.60

Lift Cover Gasket - For tractor models 135, 135 UK, 150, 165, 165 UK, 175, 175 UK, 178, 180, 20, 202, 203, 204, 205, 20C, 20E, 20F, 2135, 2200, (230, 245, 265, 275 serial number 9A349239), 235, 2500, 255, 256, 282, 30, 302, 304, 30B, 30H, 31, 3165, 35, 40, 40B, 4500, 50, 50A, 50C, 50F, 60, 65, 6500, 6500H, F40, FE35, TO35. (Item #: 112052, Ref: 886549M2) $1.70

Lift Pump Camshaft - For tractor models FE35, TO35, 135, 150, 165, 175, 202, 202, 204, 205, 302, 304, 3165, 35, 50, 65, 2135 TURF UTILITY NARROW. This camshaft has 10 spline and 1.3 Inch REAR SPLINE LENGTH. (Item #: 180715, Ref: 181993M91) $147.00

Lift Pump Cap Kit Bowl - For 135, 150, 165, 175, 180, 20, 202, 203, 204, 205, 2135, 2200, 30, 302, 304, 31, 3165, 35, 40, 50, 65, 85, 88, Super 90, FE135, FE35. Hydraulic Pump Cap Kit Bowl. Replaces 185839M1, 185555M1 (Item #: 178614, Ref: 185555M1) $12.40

Lift Pump Coupling - 10 spline coupling for models: 135, 150, 165, 175, 180, 20, 202, 203, 204, 205, 2135, 2200, 30, 302, 304, 31, 3165, 35, 40, 50, 65, 85, 88, Super 90, F40, FE135, FE35, MH50, TO35. (Item #: 173680, Ref: 180926M1_) $58.00

Lift Pump Follower - For tractor models 1080, 1085, 135, 150, 165, 175, 180, 20, 202, 203, 204, 205, 20C, 20D, 20F, 2135, 2200, 230, 231, 235, 240, 245, 250, 253, 255, 262, 265, 270, 275, 282, 283, 285, 290, 298, 30, 302, 304, 31, 3165, 35, 360, 375, 383, 390, 393, 398, 399, 40, 50, 65, 670, 690, 698, 699, F40, FE35, MH50, TO35. (Item #: 173508, Ref: 180933M1) $10.40

Lift Pump Needle Bearing - Bearing for recess in rear of camshaft for hydraulic lift pump. For tractors: TO35, MF35, MH50, MF50, MF65, MF135, MF150, MF165, MF175, MF180, MF230, MF231, MF235, MF240, MF245, MF250, MF253, MF255, MF265, MF270, MF275, MF282, MF283, MF285, MF290, MF298, MF360, MF375, MF383, MF390, MF390T, MF398, MF399, MF670, MF690, MF698, MF699, MF1080, MF1085 industrials: 20, 20C, 20D, 30, 30B, 30D, 30E, 31, 35, 40, 40B, 40E, 50C, 50D, 50E, 202, 203, 204, 205, 302, 304, 2135, 3165. (Item #: 184765, Ref: 1000251M1) $6.90

Lift Pump Plug - For tractor models 135, 135UK, 150, 165, 165UK, 175, 175UK, 178, 180, 20, 202, 203, 204, 205, 2135, 2200, 30, 302, 304, 3165, 35, 40, 50, 65, TO35. Hudraulic Pump Plug. Used with 897491M1 Valve Chamber Assembly. (Item #: 180701, Ref: 181999M1) $6.20

Selector Valve - Converts MF hydraulic to external service (valve has 3/8 inch BSP thread in pressure ports) This 3 way selecter valve is designed to fit in place of 180908M1 interface cover plate which is located on the hydraulic lift cover. Provides a positive change over from tractor hyd. to external service. Does away with need to fix the tractor lift arm in the lower position when external service is in use. The 3 point linkage of the tractor can be free for use while the external service remains connected simply by operating the valve. Services lift arms plus three external ports w/ return going back to rear end. Ports can only be used one at a time. Designed to fit in place of 180908M1 interface cover plate which is located on the hydraulic lift cover. This is a replacement for the earlier VFD1103 (Item #: 161563, Ref: VFD1104) $158.00

Lights

Miscellaneous

Oil System

Oil Filter Cartridge Type - For Perkins engines in models 135, 150, 165, 203, 205, 2135, 302, 304, 3165, 35, 50, 65, FE35. Replaces 1851766M1, 1883258M91, 1883258M92, 837595M91, 837595V91, 894975M91. This filter is (4 1/2 inches in length, 2 3/4 inch outside diameter, 3/4 inch inside diameter). (Item #: 126048, Ref: 837595M91) $7.00

PTO / Driveline

Bearing - Bearing, outer, for PTO Output Shaft (inside diameter 1.771 inch X outside diameter 2.952 inch x .629 inch thick) For tractors: TO30, TO35, MF35, MH50, MF50, MF65, MF135, MF150, MF165, MF175 late production, MF235 For tractors with dry brakes: MF255, MF265 to serial number 9A349239, MF275 to serial number 9A349239. For tractors using snap rings on bearing. (Item #: 172368, Ref: 195498M1) $34.30

PTO Seal Retainer Housing - This Seal Retainer Housing is used on many Massey Ferguson tractors. Uses 195522M1 o-ring, not included. Replaces part numbers 180465M1, 180465V1 (Item #: 151850, Ref: 180465M1) $22.80

PTO Shaft, 540 RPM - For F135, F35, F40, MH50, TO35, 135, 150, 165, 175, 180, 202, 203, 204, 205, 2135, 2200, 302, 304, 3165, 35, 50, 65 all with Live PTO, (20, 30, 31, 40, all Ind For Live PTO). PTO Shaft 540 RPM, 1 3/8 inch x 22.75 inches long, 10 drive splines, 1 snap ring groove. Replaces: 181204M92, 181204M91, 181204V92, 1812204M92, 1867084M91, M05-39-02. (Item #: 168169, Ref: 181204M92) $60.00

Shaft Bushing, PTO - For 135, 135UK, 150, 165, 165UK, 175, 175UK, 180, 20, 202, 203, 2135, 2200, 230, 235, 2500, 255, 265, 275, 30, 302, 31, 3165, 35, 35FE, 35X, 40, 4500, 50, 65, 6500, TO35. PTO Shaft Bushing. (Item #: 173076, Ref: 180461M1) $12.00

Seats

Bucket Style Metal Pan Seat - Color may vary. Size is approximately 19 inches wide x 13 inches deep x 9-1/2 inches high. Fits Models: TE20, TEA20, TO20, TO30, TO35, MF50, MH50, MF35, 50, 65, 85, 88, 98, 135, 150, 165, 230, 235, 240, 245, 250, 265, 283, 333, 444, 555, 20, 20C, 20D, 30, 30B, 30D, 30E, 31, 40, 40B, 50, 50A, 50C, 200, 2135, 2200, 3165. Uses cushion number R1001 and number R1000. (Item #: 113263, Ref: 181313M93) $75.00

Pan and Seat Cushion Set - Comes with black metal pan, black bottom cushion and black backrest cushion with metal plate and hardware. For tractor models: 135, 150, 165, 20, 20C, 20D, 2135, 2200, 235, 245, 265, 282, 283, 30, 30B, 30D, 30E, 3165, 35, 40, 40B, 50 LOADER, 50A, 50C, 555, 65, 85, 88, 98, TE20, TEA20, TO20, TO30, TO35. Replaces 181313M93, 181324M1. (Item #: 178546, Ref: 1210-1604) $156.00

Rubber Seat Bumper - This seat bumper is used with 181316M92 seat brackets. The measurements are 2 inches long, 1 inch wide, 1/2 inch thick. It includes 2 1/4 -�20 UNC screws. Replaces 181319M1, 32008AF, 354239X1, screw: 43142PF, bumper: 887074M1 (Item #: 115161, Ref: 887074M1) $8.30

Seat Bracket - This seat bracket is used on the bucket style seat part number 181313M93 and is for tractor models: TEA20, TE20, TO20, TO30, TO35, 35, 50, 65, 85, 88, 98, 135, 150, 230, 235, 240, 245, 250, 265, 20, 20C, 20D, 20F, 30, 30B, 30D, 30E, 31, 35 Turf and Utility, 40, 40B, 40E, 50, 50A, 50C, 202, 203, 204, 205, 2135, 2200, 3165. Replaces original part number 181316M92. (Item #: 155779, Ref: 181316M92) $85.00

Seat Cushion Set - Black seat cushion and backrest cover and inlay assembly. NOTE CUSHIONS MAY COME WITH WHITE PIPING. Consists of one MFCC13 and BR205. Fits later production MF235 and MF245 tractors with foam float seat. Replaces 181324M1, 181326M1, 513353M91. (Item #: 168734, Ref: FCX811) $123.00

Seat Hinge and Pins - This is the hinge and pin found on bracket part number 181316M92. It is used for attaching bucket seat part number 181313M93. It includes 181322M1 hinge link, 181321M1 pin (3/8 inch x 6-7/8 inch) and 181320M1 pin (3/8 inch x 7-5/16 inch). (Item #: 182977, Ref: 181322M1) $41.40

Sheet Metal / Body Parts

Fender With Bracket - With NON-ORIGINAL TYPE BRACKET. Rear fender, dished type with mounting bracket, mounting bracket spot welded on. For tractors without roll-over protection structure. No tool box hole. For tractors: TE20, TO20, TO30, TO35, MF35, F40, MH50, MF50, MF65 except Orchard, MF150, MF165, MF175, MF230, MF235 except Vine and Orchard, MF245, MF255 with 16 inch rims, MF265 standard, MF275 standard, MF285 standard Industrials: 20 except Turf, 20C except Turf, 30 except Turf, 30B, 35 Utility, 40, 50, 50A, 202, 203, 204, 205, 2135 Utility, 3165 Utility, also these models with 4-post R.O.P.S., 30D, 40B, 50C. For MF1100, MF1105, MF1130. Sheet metal parts may or may not come painted as pictured (unless the description states the color). They often come with only a primer coat of paint. (Item #: 104069, Ref: 8N16312) $101.00

Fender, Clamshell without Bracket - Fender Panel (Fender Skins) comes as pictured without bracket, dished type, made exactly like the original. Price is for one fender. For tractors without roll-over protection structure. For tractors: TE20, TO20, TO30, TO35, MF35, F40, MH50, MF50, MF65 exc. Orchard, MF85 standard, MF135 except Vine and Orchard, MF150, MF165, MF175, MF230, MF235. Sheet metal parts may or may not come painted as pictured (unless the description states the color). They often come with only a primer coat of paint. (Item #: 100026, Ref: 526904M1) $99.00

Hood, Dash and Grill Rubber Bumper - 1/2 inch outside diameter X 7/16 inches tall. For tractor models 20C, 20D, 20F, 30B, 30E, 30H, 40B, 40E, 50A, 50C, 50D, 50E, Super 90, TE20, TO20, TO30, 30, 31, 60, 65, 85, 88, 135, 150, 165, 175, 180, 202, 203, 204, 205, 230, 231, 235, 240, 245, 250, 255, 265, 302, 303, 404, 1080, 1100, 1130, 1150, 2135, 2200, 2640, 2675, 2705, 2745, 2775, 2805, 3165, 3505, 3525, 3545, 4500, 6500, MF 20, MF 25, MF 35, F40, MF (Ag and Ind): 40, 50, TO35. Replaces: 194768M1. (Item #: 163112, Ref: 180673M1) $2.80

Steering

Power Steering Pump Filter - Measures 1.02 inches inside diameter, 2.99 inches outside diameter, 1.61 inches height. For tractor models 11, Pony, 16, Pacer, 175, 180, 20, 202, 204, 2135, 2155, 2200, 230, 235, 245, 30, 302, 303, 304, 30B, 30D, 3165, 333, 35, 4500, 50, 50D, 555, 555D, 55D, 55G, 55K, 55LP, 65, 85, 88, Colt, FE35, FE35X, 50, Mustang, Pacemaker, TO30. VERIFY MEASUREMENTS of old filter. Replaces 1008553M1, 1052262M91, EP3, P183. (Item #: 111126, Ref: AE33538A) $12.90

Wheels

Dual Wheel Adapter - Measuring 2 3/4 inches over all length, with 9/16 UNF threads male and female sides, this adapter is used on Massey Ferguson 133, 135, 140, 148, 150, 20, 202, 204, 20C, 20D, 2135, 230, 231, 235, 240, 245, 30, 3165, 340, 342, 35, 35X, 50, 550, 65, 765, TE20, TEA20, TED20, TEF20, TO20. Replaces 818017M1 (Item #: 179639, Ref: 818017M1) $14.90

Front Lug Nut - Used on Ferguson and Massey Ferguson models 1100, 1130, 135, 148, 150, 165, 168, 175, 178, 180, 202 Indust/Const, 203 Indust/Const, 204 Indust/Const, 205, 20D Indust/Const, 20F Indust/Const, 2135 Indust/Const, 250, 253, 255, 263, 265S, 270, 271, 275, 281, 282, 283, 290, 30E Indust/Const, 30H Indust/Const, 3165 Indust/Const, 340, 342, 35, 350 Indust/Const, 352, 355, 360, 362, 365, 372, 375, 383, 390, 390T, 393, 396, 399, 40E Indust/Const, 4225, 4235, 4240, 4243, 4245, 4253, 4255, 4260, 4263, 4265, 4270, 4325, 4335, 4345, 4355, 4360, 4370, 50 Loader, 565 Combine, 575 Skid Steer Loader, 590, 65, 670, 675, 690, 765, 85, 90, F40, TE20, TEA20, TO20, TO30, TO35, the nut has 1/2 inch - 20 thread and is 1-1/16 hex head. Replaces 195489M1, 195490M1, S9512A. (Item #: 112060, Ref: 195490M1) $2.30

Spindle Tab Washer - This Tab Washer is used on Massey Ferguson FE35, TEA20, TED20, TEF20, TO20, TO30, TO35, 130, 135, 148, 150, 165, 168, 175, 178, 180, 185, 20, 20B, 20C, 20D, 20E, 2135, 230, 231, 235, 240, 245, 250, 253, 255, 265, 275, 30, 3165, 340, 342, 35, 350, 35X, 360, 375E, 40, 550, 565, 65, 765. Measures 1.50 inches (38.20mm) outside diameter, .775 inch (19.70mm) inside diameter, 0.0625 (1.23mm) inch thick. It replaces original part numbers 957E1195, 81802388, 83910701, 898349M2, 180010M1, 180010M2 (Item #: 173191, Ref: 957E1195) $1.50

Wheel Stud - Stud is 9/16 inch x 2 inch. For 130 French, 135, 135UK, 150, 20, 20C, 20D, 2135, 2200, 230, 231, 235, 240, 240P, 240S Turkey, 245, 30, 3165, 35, 35X, 50, TE20, TEA20, TO20, TO30, TO35. Also replaces 185400M1 and 185400M2. (Item #: 151964, Ref: 825507M1) $2.10

Wheel Stud - Front wheel stud. Measures 1.59 inches overall length and .930 threaded length. Threads are 1/2 UNF. These are #5 Steel per OEM specification and may come with a silver steel finish or a gold zinc finish. Fits TE20, TEA20, TO20, TO30, TO35, FE35, F40, 1100, 1130, 130, 135, 150, 165, 175, 180, 202, 203, 204, 2135, 250, 253, 255, 263, 270, 275, 281, 283, 290, 30, 3165, 340, 35, 350, 355, 360, 365, 375, 390, 4225, 4255, 4265, 50, 575, 590, 65, 675, 690, 85. (Item #: 108606, Ref: 181328M1) $1.30

Wheel Stud Nut - Nut is 9/16x18 inches For tractor models 135, 148, 150, 20, 202, 204, 205, 20C, 20D, 2135, 2200, 230, 231, 235, 240, 240P, 245, 250, 253, 265, 285, 30, 30D, 3165, 35, 50, 65, F40, FE135, FE35, TO35. May come in a silver metal color or as pictured. (Item #: 126617, Ref: 180004M1) $1.60

Wheel Stud Nut - Nut fits rear wheel stud. 9/16 inch NF. Used with 185400M1 and 185400M2 stud. For 130 French, 135, 135UK, 150, 20, 20C, 20D, 2135, 2200, 230, 231, 235, 240, 240P, 240S Turkey, 245, 30, 3165, 35, 35X, 50, TE20, TEA20, TO20, TO30, TO35. May come in a silver metal color or as pictured. (Item #: 126617, Ref: 180004M1) $1.60

Universal Parts and Accessories
Category: Accessories / Supplies

Accessories / Supplies

Auxiliary Heater, Universal - This universal auxiliary heater is used for tractor cabs, combines, backhoes, dozers, forklifts, etc. using 5/8 inch heater hose connections. Hot water forced air heat. Dimensions: 6-1/2 inches x 9-1/2 inches x 9 inches, steel powder coat housing with aluminum core. 3-speed high volume squirrel cage fan, 12-volt, 20, 000 BTU includes switch, brackets, instructions. (Item #: 182644, Ref: MIS3127) $385.00

Magnetic Block Heater - Universal. Magnetic utility heater. 120 volt AC, 200 Watts. Built-in thermostat maintains optimum temperature - will not exceed 250 degree F (121 degree C). Quick-grip handle protects hands from heat. 4-3/8 inches (11cm) length, 2-1/2 inches (6.3cm) width, 3 inches (7.5cm) height (including handle). (Item #: 178758, Ref: MBH1153) $97.00

Decals and Emblems

Ferguson Script Decal - 12 inches long, vinyl, blue and white. (Item #: 183045, Ref: R0735) $14.10

Ferguson Script Decal - 19 inches long, vinyl, green and chrome. (Item #: 178283, Ref: R0736) $25.60

Ferguson Script Decal - 26 inches long, vinyl, blue white. (Item #: 183046, Ref: R0737) $36.40

Massey Harris Trademark Decal - Red with yellow letters, 1-1/2 inches on vinyl. (Item #: 183092, Ref: R5190) $3.80

Massey Harris Trademark Decal - Yellow with red letters, 1-1/2 inches on vinyl. (Item #: 183072, Ref: R5191) $3.80

Massey Harris Trademark Decal - Red with yellow letters, 6 inches on vinyl. (Item #: 183101, Ref: R5192) $12.40

Massey Harris Trademark Decal - Yellow with red letters, 3/4 inch on vinyl. (Item #: 183066, Ref: R5236) $2.60

Massey Harris Trademark Decal - Red with yellow letters, 3/4 inch on vinyl. (Item #: 183098, Ref: R5237) $2.60

Electrical System

NOTE

Alternator - Don't see the Alternator you need for your tractor? We have many alternators not listed on this website (for tractors 1953 and newer). Just call us at 800-853-2651.

NOTE

Alternator Conversion Plug - Used to turn Delco SI Style 2-Wire plug alternators into self-exciting style. (Item #: 178026, Ref: ADR9209) $14.40

Alternator Pulley - Pulley, 3-1/8 inch diameter, 5/8 inch shaft bore, 2 grooves for 1/2 inch wide V-belt. (Item #: 179552, Ref: AP3158) $78.00

Alternator Top Adjusting Bracket, Universal - Universal Top Adjusting Bracket for Alternator or Generator is 7/8 inches wide, 1-1/2 inch offset, 8-1/4 inch from farthest end of slot to center of mounting hole, 3-3/4 inch slot length, 3/8 inch mounting hole. (Item #: 173326, Ref: 8NL10302) $25.20

No
Picture
Alternator, 12 Volt - Universal 63 Amp Delco Alternator. Single wire with built in regulator. Will fit most tractors pre 1980. (Item #: 111377, Ref: 8NE10305SE) $100.00

No
Picture
Battery Thermal Wrap - 60 Watt, 28 inches long wrap to keep your battery warm. (Item #: BTW28) $35.98

No
Picture
Battery Thermal Wrap - 160 Watt, 36 inches long wrap to keep your battery warm. (Item #: BTW72) $53.81

No
Picture
Coil - This universal automotive style coil is 28, 000 volts for a 12 volt system, 2.9 ohms. Measures 6 inches long and 2 1/2 inches diameter. (Item #: 182583, Ref: 28010) $48.50

Generator Cutout - Generator cutout for Autolite, 6-volt. For most MH models to 1951. (Item #: 105283, Ref: CB4014) $22.60

No
Picture
Spark Plug - Extended tip, 14mm thread, 3/8 inch reach. Replaces Champion J10Y, J11Y, J12Y, J13Y. NOTE: Verify spark plug type before ordering. (Item #: 179437, Ref: AL85) $5.70

Spark Plug - Standard tip, 14mm thread, .472" reach. Replaces Champion L9J, L10, L86, L86C, L88A, L90. NOTE: Verify spark plug type before ordering. (Item #: 182459, Ref: AL425) $5.30

NOTE

Starter - Don't see the starter you need for your tractor? We probably have it! Just call us at 800-853-2651 with your make, model, engine cubic inches (CID) and number off your old starter and we will see if we can find it!

NOTE

Starter Armature - Body OD: 2.921 inches, Communicator end OD: 0.563 inches, Drive End OD: 0.563 inches, Length: 12.728 inches, Communicating End to Bearing/Bushing Stop: 0.823 inches, Drive End to Bearing/Bushing Stop: 7.236 inches, Number of Comm. Bars: 23, Lam Stack Thickness: 2.685 inches, Set Screw and Keyway on Drive End. Replaces 1871662, 1878077, 1910938, 1B7705, 813555, 816163, 818002, D4100. Can fit several applications please verify OEM part before ordering. (Item #: 182636, Ref: 1871662) $93.58

Starter Drive - Drive assembly for Delco starters. Fits all MF diesel models Perkins gas models. (Item #: 111105, Ref: 1036519M91) $29.00

Starter Solenoid - Solenoid assembly, saddle mounting to starter. Services most late models, replaces Delco 1115510, on starters 1113139, 1113683, 1113676, others. 12-volt. (Item #: 105672, Ref: 1115510) $31.00

Starter, Generator, Distributor Tag, 6 Volt, Blank - Comes with 2 rivets. 2.5" long, .800" wide, 2" center to center rivet hole, .150" dia. rivet holes. Customer must stamp numbers. (Item #: 182608, Ref: DELCO6) $16.60

$Ferguson 3165 Tag for Starter\Generator, 12 Volt, Blank$
Tag for Starter/Generator, 12 Volt, Blank - Comes with 2 rivets. 2.5" long, .800" wide, 2" center to center rivet hole, .150" dia. rivet holes. Customer must stamp numbers. (Item #: 182606, Ref: DELCO12) $16.60

Engine Gaskets

Silicone Blue RTV - Permatex ultra blue, no leak RTV silicone gasket, oil resistant, use on valve covers, oil pans, timing covers, water pumps. Temperature range -75 degree F to +500 degree F, 3.35 ounce tube. (Item #: 178141, Ref: PRM77BR) $10.80

Engine Parts

NOTE

Valve Overhaul Kits - Valve Overhaul Kits are located in the Engine Overhaul Kits Section (if available for this tractor).

NOTE

Engine Rings

NOTE

Piston Ring Sets - Don't see the correct ring set for your tractor? Give us a call and ask for a Hastings Ring Set (made in USA). We need the following information to correctly find the set you need: 1. Engine size and type (Ex: 233 CID Gas) 2. Number of engine cylinders, 3. Cylinder bore size, 4. Number and size of compression rings for each piston (Ex: (2) 3/32"), 4. Number and size of oil rings for each piston (Ex: (1) 5/32").

NOTE

Exhaust System

Chrome Exhaust Stack - Single Wall, 48 inches long with a slotted, 2 inch inside diameter inlet. This is a universal part. Verify Measurements before ordering. (Item #: 118823, Ref: ZNL89020C) $81.00

Chrome Exhaust Stack - Single Wall, 48 inches long with a slotted, 2.5 inch inside diameter inlet. This is a universal part. Verify Measurements before ordering. (Item #: 119038, Ref: ZNL89025C) $108.00

Chrome Exhaust Stack - Single Wall, 48 inches long with a slotted, 3.00 inch inside diameter inlet. This is a universal part. Verify Measurements before ordering. (Item #: 114858, Ref: ZNL89051C) $130.00

Chrome Exhaust Stack - Single wall, 53 inches long with a slotted, 3.00 inch inside diameter inlet with extended curve. This is a universal part. Verify measurements before ordering. (Item #: 173286, Ref: 146520CHR) $109.00

Chrome Exhaust Stack - Single wall, 53 inches long with a slotted, 3.50 inch inside diameter inlet. It has an extended curve on the outlet. This is a universal part. Verify measurements before ordering. (Item #: 173287, Ref: 146490CHR) $168.00

Chrome Exhaust Stack - Single Wall, 48 inches long with a slotted, 4.00 inch inside diameter inlet. This is a universal part. Verify Measurements before ordering. (Item #: 114945, Ref: ZNL89057C) $144.00

Chrome Exhaust Stack - Single Wall, 48 inches long with a slotted, 5.00 inch inside diameter inlet. This is a universal part. Verify Measurements before ordering. (Item #: 119080, Ref: ZNL89485C) $173.00

Chrome Exhaust Stack - Single Wall, 42 inches long with a slotted, 2.50 inch inside diameter inlet. This is a universal part. Verify Measurements before ordering. (Item #: 173281, Ref: L102236CHR) $88.00

$Ferguson 3165 Muffler Clamp, 1-1\4$
Muffler Clamp, 1-1/4 - New Clamp for 1-1/4 inch outside diameter muffler inlet. (Item #: 182682, Ref: MC114) $2.20

$Ferguson 3165 Muffler Clamp, 1-3\4$
Muffler Clamp, 1-3/4 - New Clamp for 1-3/4 inch outside diameter muffler inlet. (Item #: 108866, Ref: MC134) $4.80

$Ferguson 3165 Muffler Clamp, 1-3\8$
Muffler Clamp, 1-3/8 - New Clamp for 1-3/8 inch outside diameter muffler inlet. (Item #: 182687, Ref: MC138) $2.80

$Ferguson 3165 Muffler Clamp, 2-1\4$
Muffler Clamp, 2-1/4 - New Clamp for 2-1/4 inch outside diameter muffler inlet. (Item #: 108870, Ref: MC214) $5.30

$Ferguson 3165 Muffler Clamp, 2-3\4$
Muffler Clamp, 2-3/4 - New Clamp for 2-3/4 inch outside diameter muffler inlet. (Item #: 108872, Ref: MC234) $8.71

Muffler Clamp, 3 - New Clamp for 3 inch outside diameter muffler inlet. (Item #: 108873, Ref: MC300) $7.80

$Ferguson 3165 Muffler Clamp, 3-1\2$
Muffler Clamp, 3-1/2 - New Clamp for 3-1/2 inch outside diameter muffler inlet. (Item #: 108874, Ref: MC312) $8.50

Muffler Clamp, 4 - New Clamp for 4 inch outside diameter muffler inlet. (Item #: 108875, Ref: MC400) $8.70

Muffler Clamp, 5 - New Clamp for 5 inch outside diameter muffler inlet. (Item #: 118841, Ref: MC500) $12.60

Rain Cap - This rain cap is for a 1.750 inch pipe. (Item #: 108632, Ref: R1799) $10.50

Rain Cap - This rain cap is for a 2.0 inch pipe. (Item #: 108633, Ref: R1800) $8.80

Rain Cap - This rain cap is for a 2.50 inch pipe. (Item #: 108635, Ref: R1802) $12.50

Rain Cap - This rain cap is for a 2.750 inch pipe. (Item #: 108636, Ref: R1804) $11.40

Rain Cap - This rain cap is for a 4.0 inch pipe. (Item #: 108645, Ref: R1807) $13.80

Rain Cap - This rain cap is for a 4.50 inch pipe. (Item #: 108749, Ref: WC14) $13.60

Rain Cap - This rain cap is for a 5.0 inch pipe. (Item #: 108750, Ref: WC15) $17.40

Stainless Steel Clamp, 2.75 Inch - This Stainless Steel Clamp is used with Chrome Stacks and in other applications. (Item #: 179749, Ref: ZNL90872A) $6.50

Stainless Steel Clamp, 4 Inch - This Stainless Steel Clamp is used with Chrome Stacks and in other applications. (Item #: 185428, Ref: ZNL90875A) $8.30

Fuel System / Air Intake

Air Cleaner Filler - Fits many air cleaners that use steel wool type filler. Custom manufactured mesh. 1 bag = 3-1/2 inch x 3-1/4 inch. (Item #: 151026, Ref: S.43231) $14.00

Carburetor Float, Zenith - This Float is used in the following Zenith Carburetors: 10277, 12188, 12199, 12205, 12234, 12236, 12238, 12253, 12384, 12389, 12535, 12599, 12654, 12744, 12956, 12982, 13096, 13201, 13206, 13238, 13309, 13355, 13371, 13386, 13405, 13415, 13420, 13452, 13453, 13492, 13549, 13605, 13646, 13653, 13665, 13694, 13705, 13713, 13719, 13720, 13727, 13729, 13730, 13733, 13800, 13803, 13805, 13822, 13825, 13851, 13861, 13862, 13865, 13873, 13878, 13879, 13880, 13902, 13903, 13910, 13933, 13957, 13971, 13975, 13983, 14002, 14017, 14019, 14044, 14086, 14094, 14096, 14099, 14100, 14115, 14133, 14147, 14175, 14178, 14179, 14183, 14993 (Item #: 108454, Ref: C85-103-S) $17.00

Fuel Line Sleeve, Pack of 10 - 7/16 inch outside diameter x 1/4 inch inside diameter x 1/4 inches wide. Replaces 33811113, 3637441M91, 376525X1, 3638466M91 (Item #: 158879, Ref: 376525X1) $4.60

Fuel Tank Screen - This Fuel Tank Screen is used with most stem-type sediment bowls to further protect against debris in the gas line. It has a 0.216 inch Insert Pipe outside diameter - 2.53 inch Overall Length. (Item #: 114940, Ref: R7949) $9.60

$Ferguson 3165 Sediment Bowl Gasket, 2-1\8 inch$
Sediment Bowl Gasket, 2-1/8 inch - For bowls with 2-1/8 inch diameter, 2.150 inch outside diameter. Made in the USA. (Item #: 112364, Ref: C1778R) $3.30

Throttle Linkage - Universal. Adjustable length ranges from 6 3/8 to 6 5/8. Rod can be cut and either re-bent or re-threaded if a shorter length is required. (Item #: 173108, Ref: 1876343M92) $14.30

Gauges

Hourmeter - DC voltages from 12 volt thru 36 volt nominal. Heavy duty glass-reinforced polyester body. Internal shock shields and grommets protect movement from shock and vibration damage. Fits 2-1/4 inch opening, three (3) mounting screws with nuts and two (2) blade terminals included. (Item #: 178318, Ref: HM771) $65.00

Hourmeter, Analog - 2 inch, black. Can be used on any tractor with a 12 to 24 volt electrical system. (Item #: 178285, Ref: S.52672) $41.00

Oil Line Adapter - Oil Gauge fittings may be different even for the same models. Here is an Oil Line Adapter if you have a gauge line without removable fittings, this converts 1/8 inch pipe thread to 1/8 inch tube. Brass. (Item #: 179540, Ref: 919095) $16.00

Hitch / Drawbar

Bracket Stabilizer - Bracket, used with telescoping stabilizer 539881M2TSK. (Item #: 178304, Ref: 514992M2) $46.00

Drawbar - Drawbar, category I, 7/8 inch pins. 11 holes, 26 inch bar length. (Item #: 103174, Ref: 180485M1) $43.20

Hair Pin Assortment - 15-piece assortment. Includes four (4) of HP-3 (wire diameter 3/16 inch, length 3.75 inch), four (4) of HP-4 (wire diameter 5/32 inch, length 2 15/16 inches), four (4) of HP-5 (wire diameter 1/8 inch, length 2 9/16 inches), and three (3) of HP-6 (wire diameter 3/32 inch, length 1 5/8 inches). (Item #: 182461, Ref: HPA15X) $12.17

No
Picture
Level Box Assembly - Leveling Box Assembly, standard right hand, category I, 20-1/2" closed, 26" open. Contains fork, shaft, pinion (185220M1-10-1/2"), housing, gear, bearing, handle and hardware. Replaces 677061, 1884760M94. Services all catergory I standard models. (Item #: 110256, Ref: HLBMF61) $70.00

Top Link Assembly, OEM Style - Category 1-1, 17-1/4 inch length of center tube. Verify size before ordering. Replaces 1870075M9. (Item #: 182641, Ref: 184134M91) $92.00

Top Link Assembly, OEM Style - Category 1-1, 18-3/4 inch length of center tube. Verify size before ordering. Replaces 184078M91, 1869954M91. (Item #: 182642, Ref: 1690177M91) $68.00

Top Link Assembly, OEM Style - Category 1-1, 21-1/2 inch length of center tube. Verify size before ordering. (Item #: 182643, Ref: 184361M91) $91.00

Top Link Assembly, OEM Style - Category 1-2, 18-3/4 inch length of center tube. Verify size before ordering. Replaces 3597172M91, 894376M1, 894376M91. (Item #: 182645, Ref: 194376M91) $90.30

Top Link Assembly, OEM Style - Category 1-2, 21-1/2 inch length of center tube. Verify size before ordering. Replaces 894377M91, 894 377M91, 894377M1 (Item #: 170303, Ref: 894377M1) $90.00

Top Link Assembly, OEM Style - Category 2-2, 18-3/4 inch Length of center tube. (Item #: 182650, Ref: 893438M91) $81.00

Top Link Assembly, OEM Style - Category 2-2, 21-1/2 inch length of center tube. Verify size before ordering. Replaces 3147681M91, 893439M91. (Item #: 184676, Ref: 1887285M91) $60.00

Top Link, Cat I and Cat II - Top link, 16 inch body combination Category II tractor and Category I implement ends, Adjust 19-1/2 inches to 29-1/2 inches overall. May or may NOT come painted red. (Item #: 112122, Ref: JSA1200R) $32.30

Top Link, Cat I, Red - Top link, 24 inch body, 3/4 inch category I ball joints. Adjusts 29 inches to 39 inches overall. Painted red. (Item #: 182651, Ref: JSA1024R) $75.00

Top Link, Cat II - Top link, 24 inch body, 1 inch Category II ball joints. Adjusts 29 inches to 41 inches. Color varies depending on availability. (Item #: 182649, Ref: JSA2024R) $95.34

Top Link, Cat II, Red - Top link, 20 inch body, 1 inch category II ball joints. Adjusts 25 inches to 37 inches. (Item #: 184552, Ref: 30108E91) $75.00

Top Link, Hydraulic - Category I (3/4 inch), 18.5" inches to 26.0 inches length, 2.00 inch cylinder bore, 9/16 inch UNF port size. (Item #: 183653, Ref: B8106) $261.00

Universal Drawbar Lock - For Cat. 1 drawbars up to 1 1/2 inch thick and 3 inches wide. Prevents drawbar from rotating. (Item #: 112156, Ref: DBL2) $37.00

Hydraulic System

Clamp, Double Break-Away, Hydraulic - For use with S20-4 and S40-4 Couplers. Quik-Cover Assembly HV4957 fits this Clamp. (Item #: 112480, Ref: S42-4) $24.84

Coupler Flange - Optional drive flange for L601-9; 5/8 inch round bore with set screw 1/4 inch x 3/8 inch # SSH4-6. 2-1/4 inch spacing. Hydraulics: Drive flange; 5/8 inch round bore with set screw 1/4 inch x 3/8 inch # SSH4-6. 2-1/4 inch b-b. (Item #: 108772, Ref: L36-6) $67.00

Filter Element - 25 Micron replacement element for SF1-25. (Item #: 182541, Ref: 1A9023) $15.40

Filter Element - 10 Micron replacement element for SF1-10. (Item #: 120092, Ref: 1A9021) $13.60

Hydraulic Hose Assembly-NPT, 12 inch - Universal. 12 inch overall length. 1/2 I.D. 2 Wire. Solid Male 1/2 NPT thread on both ends. (Item #: 118257, Ref: H42-2M-12) $11.00

Hydraulic Hose Assembly-NPT, 180 inch - Universal. 180 inch (15 Feet) overall length. 1/2 inch inside diameter. 2 Wire. Solid Male 1/2 inch NPT thread on both ends. (Item #: 179906, Ref: H42-2M-180) $55.50

Hydraulic Hose Assembly-NPT, 24 inch - Universal. 1/2 inch I.D. double wire braid (SAE-2R) with 1/2 inch NPT solid male fittings both ends. 24 inch overall length. Replaces OEM # - 407435R1. (Item #: 118256, Ref: H42-2M-24) $13.80

Hydraulic Hose Assembly-NPT, 30 inch - Universal. 30 inch overall length. 1/2 I.D. 2 Wire. Solid Male 1/2 NPT thread on both ends. (Item #: 118259, Ref: H42-2M-30) $16.10

Hydraulic Hose Assembly-NPT, 48 inch - Universal. I.H.C.: 1/2" I.D. double wire braid (SAE-2R) with 1/2" NPT solid male fittings both ends. 48" overall length. Replaces OEM # - 407437R1. Hydraulics: 48 inch overall length (Item #: 118261, Ref: H42-2M-48) $16.50

Hydraulic Pump Drive Flange - The bolt holes on the flange are 5/16 inches diameter and 2.250 center to center. This is used on a drive shaft that is 3/4 inches in diameter with a key way and set screw. This part replaces 1753730M1, 192199, 192199GV, L367GV, L36-7GV, 1753730M1GV, 1753730M91, L367. It is part of a 352 series Morflex Coupler. (Item #: 128567, Ref: 192199) $20.60

Hydraulic Selector, isolator assembly - For tractors without individual external hydraulic systems. Three position spool, forward position allows one-way (push) for single acting cylinder. Center position allows operation of the 3-point arms and the rear position will feed power to a 4 way control valve for two way (push-pull) operation of double acting cylinder. Fits all MF tractors where 182373M1 lift cover is used. Replace MF cover plate, adds 2 I/O ports 3/8 inch NPT. (Item #: 185644, Ref: TS300) $140.00

Hydraulic Valve Kit, External, Single Spool - Converts tractor for operation of cylinders on pull type implements, front loaders, hydraulic motors, or other optional hydraulics. Single spool, double acting control valve mounts conveniently on flat or shell fenders. Selector/isolator allows operation of single or double acting cylinders. Mounting hardware and instructions included. Kit contains single spool, double acting control valve, isolator valve, valve couplers, clamp hoses, adaptors, hardware and instructions. For tractor models TO35 and later where 182373M1 lift cover plate is accessible. (Item #: 178324, Ref: TS3200M) $876.00

Hydraulic Valve Manifold - This 3 Spool Valve allows operator to use auxiliary hydraulics at the same time without valve switching. Some tractors may need slight modification on seat. Includes 2 elbows. Models from 1960 and later years. (Item #: 173361, Ref: 19833A92) $1159.01

LBP Coupler Center - This LBP Coupler Center Member measures (A) 3-5/8 inch diameter (B) four 5/16 inch holes, 2-1/4 inch spacing. Replaces 1753729M91. (Item #: 178931, Ref: 192169) $75.00

Universal Pressure Gauge, Hydraulic - 1000 Lb. Gauge. Glycerin Filled. Stainless Steel Case 2-1 2 diameter. Nickel silver movement accurate to within 2%. Dual range KPA-PSI. Plexiglass crystal. 1 4 NPT male brass fitting. (Item #: 172285, Ref: GG1000) $14.60

No
Picture
Universal Pressure Gauge, Hydraulic - 60lb Gauge. Glycerin Filled. Stainless Steel Case 2-1/2 diameter. Nickel silver movement accurate to within 2%. Dual range KPA-PSI. Plexiglass crystal. 1/4 NPT male brass fitting. (Item #: 172338, Ref: GG60) $14.60

Valve - Valve for TS3200M. Single spool, 4-way, 3-position, spring loaded to neutral. No relief valve, no power beyond option. In and out ports 3/4 inch, work ports 1/2 inch NPT. (Item #: 183771, Ref: TS200BA) $304.00

Implements

Axle Bolt - Axle bolt, 1 each (Ref 3). Used on many Bush Hog rotary cutters. Used on models 12, 104, 105, 109, 126, 205, 255, 275, 285, 305, 306, 307, 405, 405HR, 406, 406HR, 502, 600, 1050, 1051, 1109, 1126, 1207, 1209, 1226, 1306, 1307, 1405, 1406, 2510, 2512, 3108, 2309, BD90, FH162, S268, SM60, SQ36 (Item #: 170217, Ref: BH1317) $14.80

Bearing Cup - This part fits Caster Assembly (Part Number BH215, Ref #6). Sold individually, two used per caster assembly. Used on many Bush Hog rotary cutters. Used on models 12, 104, 105, 109, 126, 205, 255, 275, 285, 305, 306, 307, 405, 405HR, 406, 406HR, 502, 600, 1050, 1051, 1109, 1126, 1207, 1209, 1226, 1306, 1307, 1405, 1406, 2510, 2512, 3108, 2309, BD90, FH162, S268, SM60, SQ36. Also replaces 132709, 15191, 32190M1, L44610. (Item #: 169771, Ref: 170BH) $7.86

Bearing cone (L44643) - For Caster Assembly, requires 2.Used on many Bush Hog rotary cutters. Used on models 12, 104, 105, 109, 126, 205, 255, 275, 285, 305, 306, 307, 405, 405HR, 406, 406HR, 502, 600, 1050, 1051, 1109, 1126, 1207, 1209, 1226, 1306, 1307, 1405, 1406, 2510, 2512, 3108, 2309, BD90, FH162, S268, SM60, SQ36, SQ480, SQ600. (Item #: 114630, Ref: 22) $5.90

Caster Assembly - Tail wheel and hub assembly with grease fitting and fork assembly. Shaft on Yoke is 1-1/2 inch diameter, 8 inches overall length, 7-1/4 inch to pin hole. New style tail assembly, used on the following Bush Hog cutters: 12, 104, 105, 109, 126, 205, 255, 275, 285, 305, 306, 307, 405, 405HR, 406, 406HR, 502, 600, 1050, 1051, 1109, 1126, 1207, 1209, 1226, 1306, 1307, 1405. Wheel must be attached to fork. For Bush Hog cutters with SPB40 spacer (included), assembly will also replace all models with Timken bearings. (Item #: 173612, Ref: 12269) $242.80

Caster Assembly, Old Style - Tail Wheel and Hub Assembly with grease fitting. 4 x 8 inch rim, 15 inch outside diameter of wheel. Includes wheel, hub, axle bearing and bolt assembly. OLD style tail assembly used on the following Bush Hog cutters: 12, 104, 105, 109, 126, 205, 255, 275, 285, 305, 306, 307, 405, 405HR, 406, 406HR, 502, 600, 1050, 1051, 1109, 1126, 1207, 1209, 1226, 1306, 1307, 1405, 1406, 2510, 2512, 3108, 2309, BD90, FH162, S268, SM60, SQ36, SQ480, SQ600. Wheel must be attached to fork. For Bush Hog cutters. With SPB40 spacer, assembly will also replace all models with Timken Bearings (Ref #1-#11). (Item #: 161111, Ref: BH215) $132.00

Hub Assembly - Hub with bushings (3/4 inch), wheel bolts (4), and grease fitting. Center tube length 5 inches. For rotary cutters: RB60 with new style 1-1/4 inch diameter caster, SM60R, SM160R; Squealer models: 1207, SQ36, SQ48, SQ60, SQ72, SQ148, SQ480. Replaces 60978, 60990, 63812. Can use 500BH tail wheel. (Item #: 180514, Ref: 63813BH) $37.90

Hub with Bearing Cups - 4-bolt, 5 inch bolt circle and 3-5/8 inch wheel pivot hub with bearing cups (1 inch axle) (Ref #5). This part fits caster assembly (part number BH215). Used on many Bush Hog rotary cutters. Used on models 12, 104, 105, 109, 126, 205, 255, 275, 285, 305, 306, 307, 405, 405HR, 406, 406HR, 502, 600, 1050, 1051, 1109, 1126, 1207, 1209, 1226, 1306, 1307, 1405, 1406, 2510, 2512, 3108, 2309, BD90, FH162, S268, SM60, SQ36. (Item #: 182627, Ref: BH1311) $49.70

No
Picture
Round Bale Tine 31.5 Inches - Fully Hardened. Also replaces Kverneland 221151. (Item #: 182589, Ref: 221129) $55.00

No
Picture
Round Bale Tine 38.5 Inches - Fully Hardened. Also replaces Kverneland 241107, 241161. (Item #: 182592, Ref: 241100) $95.00

No
Picture
Round Bale Tine 43 Inches - Fully Hardened. (Item #: 182594, Ref: 241166) $111.54

No
Picture
Round Bale Tine 49 Inches - Fully Hardened. (Item #: 152690, Ref: 241162) $89.87

No
Picture
Round Bale Tine 55 Inches - Fully Hardened. (Item #: 182593, Ref: 241163) $131.61

Seal, Caster - Seal, 2 required (Ref #2). Used on many Bush Hog rotary cutters. Used on models 12, 104, 105, 109, 126, 205, 255, 275, 285, 305, 306, 307, 405, 405HR, 406, 406HR, 502, 600, 1050, 1051, 1109, 1126, 1207, 1209, 1226, 1306, 1307, 1405, 1406, 2510, 2512, 3108, 2309, BD90, FH162, S268, SM60, SQ36, SQ480, SQ600. (Item #: 180300, Ref: 30BH) $4.30

Tail Wheel Assembly - 4 inch x 8 inch tail wheel assembly with laminated tire. 3-5/8 inch pilot, 4 bolt holes, 5 inch bolt circle, 3-3/4 inches wide, 15 inch outside diameter. Used on the following Bush Hog cutters: 12, 104, 105, 109, 126, 205, 255, 275, 285, 305, 306, 307, 405, 405HR, 406, 406HR, 502, 600, 1050, 1051, 1109, 1126, 1207, 1209, 1226, 1306, 1307, 1405 and 1406, 2510, 2512, 3108, 3209, BD90, FH162, S268, SM60, SQ36, SQ480, SQ600. Replaces Sidewinder 15205, Servis Rhino 373024H, Terrain King 373024H, Modern 401-0048, BMB 5337, Hardee C40-RC, King Kutter KK4X8. (Item #: 111222, Ref: 500BH) $56.00

No
Picture
Talc Powder Lubricant - Dry Talc powder lubricant, 8 lb container. Absorbs moisture and keeps treated seed from sticking together in planter boxes. Recommended application rate: 3 oz. Coverage: Typically treats 60-80 acres. (Item #: 107928, Ref: TP19000TP) $22.70

Lights

Headlight Kit, 12 Volt, LH, Chrome Ring - Kit contains 6" steel body, sealed beam bulb, chrome headlight ring, springs 4, wing, and screws 2. (Item #: 186851, Ref: S.43374) $103.00

Headlight Kit, 12 Volt, RH, Chrome Ring - Headlight Kit contains 6" steel, sealed beam bulb, chrome headlight ring, springs 4, wing, and screws 2. (Item #: 187205, Ref: S.22341) $108.25

Headlight Kit, 6 Volt, LH - Headlight assembly includes, headlight 6" steel body, sealed beam bulb, headlight ring, bulb retaining clips, winged headlight bracket (LH), Primered. Assembly required. (Item #: S.43370) $98.00

Headlight Kit, 6 Volt, RH - Includes, headlight 6" steel body, sealed beam bulb, headlight ring, bulb retaining clips, winged headlight bracket (RH), Primered. Assembly required. (Item #: S.22342) $101.00

Light Switch with Knob - Universal switch, for 6 volt tractors. Verify style is correct for your model. (Item #: 114720, Ref: AA4667R) $16.60

Portable Halogen Work Lamp - 3 inch x 5 inch sealed beam unit, 12 volt, 50 watt, 4 amp. With handle and magnetic base. Projects flood beam pattern 50 foot wide x 30 foot long. Lamp is not legal for street use. (Item #: L200MAGH) $75.13

Work Light 12V - Universal Work light is 12 volt, 3000 candle power, and a trapezoidal light pattern. I does swivel up and down, not side-to-side. Comes with 4-1/2" diameter sealed beam lamp, part number L4411. Does not have a switch on the back. (Item #: 173803, Ref: L408-12V) $38.40

Miscellaneous

Air Cond Comp - New Air conditioning compressor, replacement for Frigidaire A-6 compressor. Includes 5.58" dia. clutch and dust cover, high pressure relief valve. With 12V coil at 10 Oclock, SAE thread. Less superheat switch (comes plugged with non-functional heat switch. For tractors that have air conditioning systems using the Frigidaire A-6 compressor already. (Item #: 109093, Ref: 1904014M92) $420.00

Deluxe Canopy, 3 Bow - This universal Blue 3-Bow Deluxe Canopy comes with bows and cover. Universal brackets sold separately. Fender mounting kit is part number 6A216. Axle Mounting Kit is part number 6A217. Measures about 48 inch spread from Mounting brackets (40 inch spread at the top of canopy) Height is approximately 31 inch. (Item #: 178876, Ref: RFC100B) $245.00

Tractor Umbrella with Frame & Mounting Bracket - Red - Complete umbrella consisting of a cover, bracket and frame, 54" x 54" cover made of 10 oz. duck canvas with leather reinforcements and steel grommets, Metal parts are zinc-coated for long-lasting, maintenance-free service, Rigid framework for cover is built to withstand farm and industrial use, Installs easily, folds down for trailering and removes in seconds without tools, (Item #: 161193) $123.00

PTO / Driveline

Coupler Repair Kit - Coupler repair kit, services all Hub City over-running couplers. Contains keys, roll pin, set screw, springs, spacer, and retaining ring. (Item #: 182663, Ref: CRK600) $92.00

Driveline Assembly with Yokes - AB4 series, complete drive shaft assembly with shielding and tractor and implement yokes. 1-3/8 inch 6 spline Q.D. tractor yoke. 1-3/8 inch round bore with 1/2 inch pin hole implement yoke. 1300 mm (51 inch) overall length end of yoke to end of yoke. 1110 mm (43-3/4 inch) compressed length center to center of cross bore. Cross and bearing kit, 27 mm 1.063 (1-1/16 inch) bearing diameter x 74.6 mm 2.940 (2-15/16 inch) overall length (43-3/4 inch). Verify length before ordering. (Item #: 180775, Ref: AB4111WY) $175.00

Driveline Assembly with Yokes - AB4 series, complete drive shaft assembly with shielding and tractor yoke, ratcheting torque limiter on implement end. 1-3/8 inch 6 spline Q.D. tractor yoke, 1-3/8 inch 6 spline ratcheting torque limiter with quick disconnect on implement end. 1372 mm (54 inch) overall length end of yoke to end of clutch. 1110 mm (43-3/4 inch) compressed length center to center of cross bore. Cross and bearing kit 27 mm 1.063 (1-1/16 inch) bearing diameter x 74.6 mm 2.940 (2-15/16 inch). 1372 mm (54 inch) overall length ***VERIFY LENGTH BEFORE ORDERING*** (Item #: 124815, Ref: AB4111K33) $339.00

NOTE

PTO Adapter - PTO adapters are located under the PTO category in the Accessories and Universal Parts section.

NOTE

PTO Quick Release Pin - PTO quick release pin fits MOST American yokes. Replaces: 1810351M91, QDK1, QDK1M. (Item #: 112246, Ref: 1810351M91) $4.50

PTO Safety Clutch, 40 HP - 1-3/8 inch 6 spline male and female ends, 6 inch diameter, 40 horse power capacity. Heavy duty unit allows PTO driven implements to freewheel with adjustable safety protection under load. Prevents expensive damage to internal tractor PTO packs. Prevents single clutch tractors from being driven forward by PTO over-run. (Item #: 183648, Ref: B9164) $275.00

Paint

44 Minute DVD - How to Paint a Tractor - This DVD demonstrates the entire painting process including sanding, priming, body work, painting and decals. A John Deere B is used as the sample tractor, but the information will pertain to any make or model - the techniques are the same. Safety is also discussed. (Item #: 183950, Ref: JDV-02250) $24.00

No
Picture
Paint, Aluminum High Heat Spray Can - 12 oz. spray can. Withstands heat up to 650 degrees for use on stacks and mufflers. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100244, Ref: TP402HHSP_) $8.50

No
Picture
Paint, Aluminum, Spray Can - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100244, Ref: TP312SP) $8.50

No
Picture
Paint, Clear Coat, 1 Gallon - From Tallmans, formulated by Van Sickle, providing OEM quality. High strength air dry Acrylic laquer. Protects the original paint finish, adds more shine, prolongs color and prevents fade. Water clear non-yellowing gloss coat, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 108409, Ref: TP447GAL) $64.00

No
Picture
Paint, Clear Coat, 1 Quart - From Tallmans, formulated by Van Sickle, providing OEM quality. High strength air dry Acrylic laquer. Protects the original paint finish, adds more shine, prolongs color and prevents fade. Water clear non-yellowing gloss coat, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 108408, Ref: TP447QT) $29.30

No
Picture
Paint, Dark Gray, 1 Gallon - This Dark Gray was used on Ferguson Implements from 1939 through 1948. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Fords (1939-1947). Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 108333, Ref: TP2888GAL) $57.00

No
Picture
Paint, French Silver Mist Gray, 1 Gallon - High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 108364, Ref: TP750GAL) $71.00

No
Picture
Paint, French Silver Mist Gray, 1 Quart - High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 108363, Ref: TP750QT) $27.00

No
Picture
Paint, French Silver Mist Gray, Spray Can - High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 108362, Ref: TP750SP) $11.40

No
Picture
Paint, Gloss Black, 1 Gallon - High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100116, Ref: TP550GAL) $53.00

No
Picture
Paint, Gloss Black, 1 Quart - High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100115, Ref: TP550QT) $24.00

No
Picture
Paint, Gloss Black, Spray Can - High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100114, Ref: TP550SP) $8.70

No
Picture
Paint, Gray Primer, 1 Quart - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100121, Ref: TP2700QT) $22.40

No
Picture
Paint, Gray Primer, Spray Can - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. (Item #: 100120, Ref: TP2700SP) $8.40

No
Picture
Paint, Industrial Yellow, 1 Gallon - High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 184671, Ref: TP540GAL) $150.00

No
Picture
Paint, Industrial Yellow, 1 Quart - High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 108372, Ref: TP540QT) $61.00

No
Picture
Paint, Light Gray, 1 Gallon - From Tallmans, formulated by Van Sickle, providing OEM quality. TO35 Sheet Metal 1954-56 and implements after 1954. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 108367, Ref: TP235GAL) $90.00

No
Picture
Paint, Light Gray, 1 Quart - OEM quality. TO35 Sheet Metal 1954-56 and implements after 1954. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 108366, Ref: TP235QT) $35.00

No
Picture
Paint, Light Gray, Spray Can - TO35 Sheet Metal 1954-56 and implements after 1954. From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 108365, Ref: TP235SP) $11.00

No
Picture
Paint, MF Red, 1 Gallon - This Massey Ferguson Red was used from 1956 through 2008. It is High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 102660, Ref: TP300GAL) $52.00

No
Picture
Paint, MF Red, 1 Quart - This Massey Ferguson Red was used from 1956 through 2008. It is High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 102659, Ref: TP300QT) $21.60

No
Picture
Paint, MF Red, Spray Can - This Massey Ferguson Red was used from 1956 through 2008. It is High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 102658, Ref: TP300SP) $7.70

No
Picture
Paint, MH Red, 1 Gallon - This Massey "Old Red" was used from 1956 through 1965. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 108370, Ref: TP340GAL) $55.00

No
Picture
Paint, MH Red, 1 Quart - This Massey "Old Red" was used from 1956 through 1965. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 108369, Ref: TP340QT) $24.00

No
Picture
Paint, MH Red, Spray Can - This Massey "Old Red" was used from 1956 through 1965. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 108368, Ref: TP340SP) $10.20

No
Picture
Paint, Red Primer, 1 Gallon - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100119, Ref: TP3987GAL) $59.00

No
Picture
Paint, Red Primer, 1 Quart - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100118, Ref: TP3987QT) $24.00

No
Picture
Paint, Satin Black, 1 Quart - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics.Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100254, Ref: TP225QT) $24.00

No
Picture
Paint, Satin Black, Spray Can - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics.Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100253, Ref: TP225SP) $8.50

No
Picture
Paint, Straw Yellow, 1 Gallon - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 108373, Ref: TP345GAL) $138.00

No
Picture
Paint, Straw Yellow, 1 Quart - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 108372, Ref: TP345QT) $61.00

No
Picture
Paint, StrawYellow, Spray Can - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 108371, Ref: TP345SP) $10.90

No
Picture
Paint, Yellow Primer, 1 Gallon - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 184741, Ref: TP2720GAL) $84.67

No
Picture
Slip Resistant Coating - Gallon can. For use in a variety of applications where slip resistance or sound deadening qualities are desired. Moisture and chemical resistant, helps protect against corrosion. Ready to use as is for easy application and touch up with brush or roller. Coverage area is 75 to 100 square feet. (Item #: BL116GAL) $68.39

No
Picture
Slip Resistant Coating Kit - Do it yourself kit. Comes with one gallon of liner, mini roller with tray, two replacement roller covers, 2" brush, and sanding sponge. For use in a variety of applications where slip resistance or sound deadening qualities are desired. Moisture and chemical resistant, helps protect against corrosion. Ready to use as is for easy application and touch up with brush or roller. Coverage area is 75 to 100 square feet. (Item #: BL116KIT) $99.22

Tire Paint, Black - Black tire paint (1 Gallon)- The best way to make tires look like new. Our paint is a permanent water based paint that applies easily and dries quickly. It will not rub off even when wet. Gives dull, faded tires a non-glossy, like new finish. This paint is READY TO USE. (Item #: 185598, Ref: E844R) $40.01

Seats

No
Picture
Seat Cover (Red and Yellow) - Tie-on for 19 inch wide pan seat. For Tractors that have a Red and Yellow color scheme. (Item #: XYFR30RY) $31.50

Seat, Air Suspension, Black Leatherette, Universal - Seat, Deluxe AG Air suspension, Includes 12 volt compressor. Slides, fore/aft and lateral isolators, adj shock, seat top with Black Leatherette upholstery, lumbar, recline tilt up and angle adjust armrests. *Adjustable backrest recline. *Infinitely adjustable mechanical lumbar support *Heavy duty 12 volt air compressor included. *DOUBLE LOCKING SLIDES, fore and aft isolators with lockout. *Ride firmness adjustment *Weight range 110-330 lbs. *** CALL FOR FREIGHT QUOTE *** (Item #: TS5056V) $1518.86

Tie-On Seat Cover - Grey, 19 inches wide. Deluxe with 2 inches of foam. This fits a PAN seat. (Item #: 178997, Ref: R2600) $51.00

Universal Seat - Color: Yellow - Universal Application Leatherette Suspension seat. For most Compact, Agricultural and Industrial Tractors. Adjustable base for 5 different mounting angles, Internal Suspension Weight Adjustment, Special Slotted Base for mounting holes adjustments of approximately 2-1-2 inches forward/rear, Adjustable Slide Track. IMPORTANT: THESE SEATS FIT MOST TRACTORS, BUT NOT ALL. PLEASE LOOK CLOSELY AT THE DIMENSIONS ON THE PICTURE BEFORE ORDERING TO BE SURE IT WILL FIT YOUR TRACTOR. Color is John Deere Yellow. (Item #: 101375, Ref: TS1040ATSP) $103.00

Sheet Metal / Body Parts

Bumper - Bumper assembly, mounting arms NOT included. Sheet metal parts may or may not come painted as pictured (unless the description states the color). They often come with only a primer coat of paint. (Item #: 178311, Ref: BU10211R) $135.00

Cab Foam Kit Spray Adhesive - 1 16 Oz. can will attach most kits. Large, multi piece kits may need 2 cans. (Item #: 165963, Ref: R0140) $41.19

Steering

Eaton Power Steering Pump Replacement - This Power Steering Pump replaces the Eaton style belt driven Power steering Pump. It also replaces Eaton part numbers: 503-1005-005, 20928 and P761. This is a Redesigned Pump that uses a bearing instead of original bushing. It can also be adapted to tractors using Char-Lynn Power Steering with an Eaton Pump. Please note that this pump does not include brackets, top mounted reservoir, or pulley. Some applications will require a new pressure hose to be made for a 5/8-18 inch inverted flare type fitting. The shaft diameter measures .670 inches. The shaft length, where the pulley mounts measures .575 inches. There is a 2 inch thick pump housing where the bracket bolts on. Pressure is preset at 1.32 GPM. (Item #: 113730, Ref: S03-1003) $381.00

Filter, Power Steering - Filter case size is 3 inches diameter and 1 1/2 inch height. Center hole is approximately 7/8 inch diameter. VERIFY size before ordering. It is used on tractors with Eaton style power steering pumps. Replaces: 1008553M1, 1052262M91 (Item #: 111126, Ref: AE33538A) $12.90

Power Steering Pump Pulley - This Power Steering Pump Pulley is used with S03-1003 Power Steering Pump. It is designed for Tractors using Eaton Style power steering pump. It is made of Stamped steel. Measures 5 inches outside diameter, 0.675 inch bore, 1/8 inch keyway, 0.9715 inch total width for 1/2 inch belt. (Item #: 164438, Ref: ABC1417) $47.40

Tie Rod Boot Assortment - Includes 6 Tie Rod Boots. Two each of the following sizes: 1 13/16 inches x 5/8 inch x 5/8 inch, 1 15/16 inches x 3/4 inch, 3/4 inch, and 1 3/8 inches x 1 inch x 1/2 inch. (Item #: 183427, Ref: TIERODBOOTS) $13.00

Tools

No
Picture
Blade Fuse Assortment - With 6-24 volt tester light and fuse puller. Contains 93 pieces. 5, 10, 15, 20, 25 and 30 amp blade type fuses. (Item #: 183798, Ref: S.29891) $24.30

No
Picture
Hay Moisture Tester - Self Calibrating Electronic Moisture Tester. (Item #: 180261, Ref: S.58474) $301.00

Tractor Manual Search - Yesterday's Tractor Co.

Wheels

Front Rim - This is a 6 inches x 16 inches Front Wheel Rim. It has a pilot hole of 4.625 inches. It uses 6 bolts in a 6 inch bolt pattern. Back-spacing is 4.75 inches. Verify size of old rim before ordering. Replaces: 183027M91, 509893M91 (Item #: 103768, Ref: FW60166) $95.00

Front Rim - This is a 5.5 inch x 16 inch Front Wheel Rim. It has a pilot hole of 4.625 inches. It uses 6 bolts in a 6 inch bolt pattern. Back-spacing is 4.75 inches. Capacity of 3500 lbs based on 20 MPH max speed. Verify size of old rim before ordering. Replaces AL82488, A38404, C7NN1007J, D2NN1007N, D2NN1007S, D8NN1007BA, E1ADDN1015B, E1ADKN1015A, E6NN1007BA, G57046, K914312, K921475, K947941, VPH6001, 1660769M1, 1678319M91, 1678319M92, 1691618M92, 1691618R92, 1883333M92, 3114166R91, 509893M1, 509893M91, 57512110, 70000-00028, 751734R91, 82005056, 83900159, 83954658, 83960327, 9A306 (Item #: 116854, Ref: FW55166) $74.00

Rim 10X28 - This rim measures 10 inch x 28 inch demountable rim with 6 loop clamps. Loops are designed for 5/8 inch bolts. May come Painted primer or aluminum or off white color. Replaces 180863M91. (Item #: 103719, Ref: NCA1020B) $135.00

Rim 11X28 with 6 Loop Clamps - This rim is 11 inch x 28 inch demountable rim with 6 loop clamps. Loops are designed for 5/8 inch bolts. Painted aluminum color. Shipped via truck Add $25.00 extra shipping per rim due to weight. Replaces 535450M91. (Item #: 104209, Ref: C5NN1050E) $147.00

Rim, 12X24 - Rim, 12 x 24 demountable rim for 13 x 24 or 14 x 24 tires. Add $52.95 extra shipping due to weight. 6 Loops, these measure 20 1/4 inches center-to-center across from one another. Uses special S.04352 bolt and nut kit. (Item #: 108579, Ref: 535454M91) $142.00

Tire Inner Tube - This Inner Tube fits 4.00 x 15, 5.00 x 15, 5.90 x 15, 4.50 x 16 and 5.00 x 16 tires. It has a TR-15 valve stem. Valve height 1.38 inch, diameter 0.65 inch. (Item #: 118299, Ref: 500X15TB) $17.15

Tire Tube - For 5.50 inch, 6.00 inch, or 6.50 inch X 16 inch tires. This is a bias style tube, not for radial tires. Not for recreational use. (Item #: 118295, Ref: WHS050) $18.70

No
Picture
Tire Tube 24 Inch - This 24 inch tire tube is used for all tractors with the following tires: 10.00 x 24, 11.00 x 24, 11.2 x 24, and 12.4 x 24. (Item #: 178957, Ref: WHS059) $57.00

No
Picture
Tire Tube 28 Inch - This tire tube is used for all tractors with the following tires: 10.00 inch x 28 inch, 11.00 inch x 28 inch, 11.2 inch x 28 inch and 12.4 inch x 28 inch. (Item #: 158249, Ref: WHS058) $62.00

No
Picture
Tire Tube 28 Inch - This 28 inch tire tube is used for all tractors with the following tires: 12.00 x 28, 13.00 x 28, 13.6 x 28, and 14.9 x 28. (Item #: 178895, Ref: WHS061) $111.00

No
Picture
Tire Tube 32 Inch - This 32 inch tire tube is used for all tractors with the following tires: 7.00 inch x 32 inch, 8.00 inch x 32 inch, 9.00 inch x 32 inch and 9.5 inch x 32 inch. (Item #: 184736, Ref: WHS062) $67.00

No
Picture
Tire Tube 38 Inch - This 38 inch tire tube is used for all tractors with the following tires: 10.00 inch x 38 inch, 11.00 inch x 38 inch, 11.2 inch x 38 inch and 12.4 inch x 38 inch. This is a bias style tube. Not for use with radial tires. (Item #: 183819, Ref: WHS064) $82.00

Tire, Three Rib - Front tire, 3 Rib, 5.50 inch x 16 inch. Designed to be used with tube (part number WHS050). 6 Ply. Additional $20 shipping due to size and weight. (Item #: 118213, Ref: 550X16) $107.00