FREE SHIPPING on orders above $249.99! Details

• Tractor Parts

• Engine Kits

• Carburetors

• Salvage

• Manuals

• DVDs

• Hats

• Contact Us

• Shipping Rates

• Return Policy

• Ordering Help

• Company Info

• Parts Warranty

• Forums

Massey Ferguson 35 Tractor Parts

[Categories] [All Massey Ferguson Models] [Print]

Brakes

Actuator and Latch Kit - With spring and clevis pin. For tractor models TO35, FE35, F40, MH50, 50, (65 up to serial number 692932), 135, 150, 230, 235, (240 up to 2/1995), (283 Brazil), 20, 20C, 30B, 30D, 35 Turf and Utility, (40, 40B, 50C, 50D with instant reverse transmission), 50. Replaces 181450M1, 181449M1, 180809M1, 181149V1. (Item #: 169743, Ref: 181450M1) $18.10

Brake Adjuster Spring - This Spring is 5-3/16 inches over all, has a 2-11/16 inch coil length and a 5/8 inch coil diameter. It is used on tractor models FE35, 135 UK, 231, 240, 20D, MF 35 UK. Replaces original part number 1850217M1 (Item #: 124543, Ref: 957E2035) $4.30

Brake Anchor Spring - This Brake Anchor Spring is 4 inches overall length, has a 2-3/8 inch coil length and 5/8 inch coil diameter. It is used on the following Ferguson and Massey Ferguson tractors: FE35, TEA20, TEF20, 135 UK, 165 UK, 178, 231, 240 175 UK, 20D, 50F, 50H, 60H, MF 35 UK. Replaces original part numbers 825064M1 and 1890319M1 (Item #: 178056, Ref: 957E2036) $5.00

Brake Arm - For tractor models 35, 35UK, 50, (135 up to serial number 9A106904), 135UK, (150 up to serial number 9A106430), 240, (20 serial number 9A106430), 20D, (30 up to serial number 9A106430), 35 Turf and Utility, 2135, 3165. (Item #: 180864M1) $20.27

Brake Drum - Brake drum 16 inch outside dia 4 1/2 inch hub diameter. For tractors: TO35, MF35, F40, MH50, MF50, MF135 (except orchard), MF150, MF230, MF235 (except orchard), MF240, MF245 (except orchard). Industrials: 20, 20C, 20D, 30 turf, 35, 40, 202, 204, 2135, 2200, 3165. Uses two 182278M1 retaining screws per drum (not included). Replaces 181230M1, 827707M91, 827707M7, 827707M6, 827707M3, 825631M91, 822707M5, 8207707M4, 181230M1, 827707M1, 827707M4, and A827707M5. (Item #: 105637, Ref: 827707M5) $95.00

Brake Drum Retaining Screw - This Brake Drum Retaining Screw Measures 1/2 -13 NC x 3/4 inches. Four are used per tractor, sold individually. If you order 1, you are only going to get one screw. It is used on the following with shoe style brakes: 2200, 2135, 3165, 20C, 20D, 30, FE35, TE20, TEA20, TO20, TO30, F40, TO35, 130, 20, 202, 204, 35, 135, 148, 150, 230, 231, 240, 245, 340, 35, 50, MH50, 550. It is used with 827707M5 Break Drum. Replaces: 182278M1, TO1127. (Item #: 125739, Ref: 182278M1) $1.90

Brake Pedal Lock - For tractor models 135 UK, (202 gas), (203 diesel), 20D, 20F, 240, 240S, 250, 253, 30E, 35, 40E, (50 serial number up to 533414), (65 serial number up to 692932), FE35, TO35. (Item #: 173120, Ref: 181960M1) $14.80

Brake Pedal Shaft - This Brake Pedal Shaft is used on Ferguson F40, TO35, Massey Ferguson 135, 150, 3100, 3165, 20, 2135, 30, 35, 50, Massey Harris 50. Replaces 181959M1, 1860802M1, 200191M1 (Item #: 180160, Ref: 1860802M1) $43.90

Brake Pedal Shaft Bushing - For Massey Ferguson tractor models TO35, 35, 35X, 50, 65, 135, 150, 165, 175, 178, 230, 235, 240, 245 (s/n 9A349239-earlier), 250, 253, 263, 265, 265S, 271, 281, 282, 283, Compatible with Massey Ferguson Construction and industrial models 20, 20C, 20D, 20F, 30, 30E, 31, 40, 40E, 202, 203, 2135, 3165, Replaces Massey Ferguson OEM number 195910M1, (Item #: 150916) $13.40

Brake Pin Kit - Brake Pin Kit to service your brakes. For models TO20, TO30, TE20, 135 UK, 165 UK, 175 UK, 178, 20D, 231, 240, 240P, 240S, 35, 35X, 50F, 50H, 60H. (Item #: 105640, Ref: 1810029M91) $4.98

Brake Plate - This Brake Plate us used on multiple Massey Ferguson Tractors. Replaces 827143M91, 825040M1, 825040M2, 825041M1, 825041M2, 827143M92, 827143M94, 827143M95, 827143M96, 897042M1, 897042M2, 87089998. (Item #: 105639, Ref: 827143M95) $203.00

Brake Shaft, Bushing - 1-3/8 inch x 1-1/2 inch x 1-7/16 inch. For tractor models TE20, TO20, TEA20, TO30, TO35, FE35, F40, 1080, 135, 150, 165, 175, 180, 230, 235, 245, 255, 265, 275, 285, 35, 50. (Item #: 150915, Ref: 180801M1) $8.50

Brake Shoe Set - 4 brake shoes with linings bonded for 20, TO35, 35, F40, 50, 135, 150, M230, MF235 Standard and Orchard, MF245, (2 wheel set). Replaces 830480M93, 830480M92, 830480V93 (Item #: 105625, Ref: 830480M93) $90.00

Spring, Parking Brake Latch - For tractor models F40, FE35, TO35, 1080, 1085, 135, 135 UK, 150, 165, 165 UK, 175, 175 UK, 178, 20, 230, 235, 240, 282, 30, 3165, 65, 35, 35 UK, 40, 50, MH50. (Item #: 173676, Ref: 180809M2) $3.40

Clutch

Carrier - Carrier for clutch release bearing. Carrier bore 2.228 inch (2-1/4 inch approximately), outside diameter 2-1/2 inch. PLEASE CHECK CARRIER BORE BEFORE ORDERING. This part is used on many Massey Ferguson Agriculture and Industrial Models. Replaces 519232M1, 886727M1, 886727M2, 886727M3, 886727T4 (Item #: 112309, Ref: 886727M4) $15.90

No
Picture
Clutch Alignment Tool - Dual Stage Clutch Alignment Tool with 1 1/8 inch by 10 splines and 1 5/8 inch by 25 splines. For tractor models 133, 135, 140, 148, 150, 152, 155, 158, 165, 168, 175, 175UK, 178UK, 180, 20, 20C, 20D, 20E, 20F, 2135, 230, 231, 235, 240P, 240S, 245, 253, 255, 261, 263, 265, 265S, 270, 271, 271X, 271XE, 275, 281, 281X, 281XE, 282, 283, 285, 285S, 290UK, 30, 30E, 3165, 35, 40E, 383, 390, 481, 670, 690, 50, 65, 97, TO35. (Item #: 119890, Ref: 1212-5955) $17.00

Clutch Alignment Tool - Clutch alignment tool for 5/8 inch Pilot, 1st stage 1 1/8 inch with 10 splines, 2nd stage 1 3/4 inch with 10 splines. (Item #: 114714, Ref: 1212-1600) $22.10

Clutch Assembly, Dual - Dual Clutch uses 11 inch main disc (1-1/8 inch 10 spline hub) (NOT INCLUDED) and 9 inch PTO disc (1-3/4 inch 10 spline hub) (INCLUDED). Fits 35, 50, 135, 150, Industrials: 35 Turf, 35 Utility, 2135, 20 Turf, 20 Utility, 40. Replaces 526666M91, 512355M91, 193930M92, 184541M94, 533795M91 all having a 1 3/4 inch flywheel offset. (Item #: 122846, Ref: 526666M91) $292.00

Clutch Cover Release Lever Pin - Pivot pin, for clutch cover release lever to cover on tractors: MF240, MF250, MF253, MF270, MF275, MF282, MF283 except Brazil, MF290, MF298, MF383, MF390, MF398, MF399, MF690, MF698, MF699 industrials: 20D, 30E, 35, 50E. Also used as an alternate on clutch covers manufactured in the United Kingdom for the following tractors: MF35, MF50, MF65 industrial: 20. For 20, 20D, 30E, 35, 50E, MF240, MF250, MF253, MF270, MF275, MF282, MF283, MF290, MF298, MF35, MF383, MF390, MF398, MF3989, MF399, MF50, MF65, MF690, MF698, MF699. Price shown is for each, sold only in multiples of 3 items. (Item #: 183795, Ref: 891826M1) $6.60

Clutch Disc, 11 Inch - 10 spline, 1.125 inch hub. For all MF tractors with 11 inch DUAL Clutch, EXCEPT for TO35: (to serial number 177394 and 177520 thru 177537); F40, MH50. Tractors: TO35 late production, 35, 50, 65, 135, 150, 165, 175, 180, M230, MF235, MF245, MF255, MF265, MH50, industrials: 20, 20C, 30, 30B, 30D, 40B.. Will replace 890302M91. (Item #: 112308, Ref: 516068M91) $44.00

Clutch Disc, 11 Inch - 10 Spline 1.125 spline diameter. Feramic, solid. For tractor models 130, 135, 165, 175, 180, 20, 202, 203, 2135, 2165, 2200, 230, 245, 25, 255, 265, 290, 30, 302, 30B, 30D, 3165, 35, 40B, 50 serial number 515396->, 65, TO35 serial number 177395-177519 and 177538->. All with dual clutches. (Item #: 112308, Ref: 185892-RF) $44.00

Clutch Disc - 6 Pad - For Massey Ferguson tractor models TO35, 35, 50, 65, 135, 150, 165, 175, 180, 230, 235, 245, 255, 265, 2200, Compatible with Massey Ferguson Construction and industrial models 20, 30, 30B, 30D, 40, 40B, 202, 203, 302, 2135, 3165, Replaces Massey Ferguson OEM number 184542M91, 185892M94, 193141M91, 516068M91, 516068M93, 890302M91, Clutch Diameter: 11", Clutch Hub Diameter: 1-1/8", Clutch Spline: 10, Clutch Center: Solid, Clutch Type: 6 Regular Pads, (Item #: 122774) $168.00

Clutch Disc, 9 Inch - 10 spline on a 1 3/4 inch hub diameter. PTO Clutch Disc For 20, 30, 40, F40, MF135, MF150, MF165, MF175, MF180, MF35, MF50, MF65, TO35. (Item #: 163114, Ref: 3620411M91) $52.00

Clutch Disc, 9 Inch - Clutch disc is 9 inches in diameter with 10 splines on a 1 1/8 inch hub. Used on models 135, 2135, 35, 50, TO35, TE20, TEA20, TO20, TO30, Colt, Mustang, Massey Harris 22, Massey Harris 30 with single clutch. Replaces 760260M91, 180241M91, 180250M91, 181114M91, 193621M91, 825495M91 (Item #: 119397, Ref: A44512) $60.00

Clutch Disc, Remanufactured - For Massey Ferguson tractor models TO35, 35, 50, 65, 135, 150, 165, 175, 180, 230, 235, 245, 255, 265, 2200, Compatible with Massey Ferguson Construction and industrial models 20, 30, 40, 202, 203, 302, 2135, 3165, Clutch Size: 11", Clutch Hub: 1-1/8", Clutch Spline: 10, Clutch Center: Solid, Clutch Type: 6 Reg Pads, (Item #: 206742) $149.00

Clutch Disc, Remanufactured, 180241M91 - For Massey Ferguson tractor models TE20, TEA20, TO20, TO30, TO35, 35, 50, 135, Compatible with Massey Ferguson Construction and industrial models 202, 203, 2135, Replaces Massey Ferguson OEM number 180241M91, 180250M91, 181114M91, 183357M91, 193621M91, 825495M91, Clutch Size: 9", Clutch Hub: 1-1/8", Clutch Spline: 10, Clutch Center: Solid, Clutch Type: 4 Reg Pads, (Item #: 206747) $116.00

Clutch Disc, Remanufactured, 184542M91 - For Massey Ferguson tractor models TO30, 35, 50 (s/n 515433 - later), 65, 135, 150, 165, 175, 180, 230, 235, 245, 255, 265, 2200, Compatible with Massey Ferguson Construction and industrial models 20, 30, 40, 202, 203, 302, 2135, 3165, Replaces Massey Ferguson OEM number 184542M91, 185892M94, 193141M91, 516068M91, 516068M93, 890302M91, Clutch Size: 11", Clutch Hub: 1-1/8", Clutch Spline: 10, Clutch Center: Solid, Clutch Type: 4 Reg Pads, (Item #: 206741) $114.01

Clutch Disc, Remanufactured, 189948M91 - For Massey Ferguson tractor models 35, 65, 165, 175, 180, 255, 265, 2200, Compatible with Massey Ferguson Construction and industrial models 30, 31, 40B, 50C, 50D, 202, 203, 2135, 2200, 2500, 3165, 4500, Replaces Massey Ferguson OEM number 189948M91, 193070M1, 513580M91, 5269645M92, 526965M91, Clutch Size: 11", Clutch Hub: 1-1/8", Clutch Spline: 10, Clutch Center: Solid, Clutch Type: Woven, For a New version of this sku use Item #: 130134, (Item #: 206750) $93.01

Clutch Disc, Used - For Massey Ferguson tractor models 30, 35, 50, 65, 150, 178, 180, 235, 240, 245, 255, 265, 270, 275, 285, 290, 298, 360, 362, 375, 383, 390, 393, 396, 398, 399, 670, 690, 698, 699, 1080, 1085, Compatible with Massey Ferguson Construction and industrial models 20E, 30E, 40E, 50E, 50H, 60H, Replaces Massey Ferguson OEM number 523552M1, 1862289M2, 1869665M1, 1870879M1, 190177M1, 514276M1, 521282M1, 533326M2, 1870074M1, 1672626M1, O.D: 5.05", I.D: 3.457", Internal teeth: 57, Sold Each, For a new version of this item use Item #: 114029, Used items are not always in stock. If we are unable to ship this part we will contact you within one business day., (Item #: 460628) $7.01

Clutch Finger Kit - This Clutch Finger Kit is used on 11 inch Double Clutch Pressure Plates. It replaces (3) Adjusting Bolt 1853164M1, (3) Adjusting Bolt Locknut 353430X1, (3) Lever Spring 893121M2 (1022902M1), (3) Lever 1754681M2 (899818M2), (3) Pivot Pin 828597M2, (3) Cotter Pin 354048X1. (Item #: 178977, Ref: S.40687) $51.00

Clutch Fork Shaft, LH - This Clutch Fork Shaft is the left (long) side. It measures 1 inch in diameter by 5-17/32 inches long. It is used with: 184592M1 bushing, 886719M1 fork and 180449M1 RH shaft (each sold separately). Replaces 180444M1, 180444M2, 1679460M1 (Item #: 166103, Ref: 180444M1) $9.70

Clutch Kit - Clutch Kit contains 181114M91 drive disc that measures 9 inch outside diameter with 1 1/8 inch 10 spline hub, 183209M91 9 inch single pressure plate, 832960M3 pilot bearing, and 195207M1 release bearing and 10 spline x 1 1/8 inch pilot tool. Will not fit on input shaft with 1 3/8 inch 10 Spline end. Note: for TO35 see part number 833085M2 bearing, you may need kit 184827. Replaces 1800263M91, 180263M91, 181114M91. (Item #: 119387, Ref: 1212-1610) $171.00

Clutch Kit - Our new 9 inch complete clutch kit contains: a 9 inch 3 finger, 6 spring pressure plate assembly (183209M91), a 9 inch, 10 spline, 1 3/8 inch hub clutch disc (180250M91), new release bearing (195508M1), new pilot bearing (828123M2), and clutch alignment tool. For tractor models 135, 2135, 35, 50, MH22, MH22K, TE20, TEA20, TO20, TO30. (Item #: 113484, Ref: 1212-6001) $166.00

Clutch Kit - Kit contains 181114M91 drive disc 9 inch outside diameter with 1 1/8 inch 10 spline hub, 183209M91 9 inch single pressure plate, 832960M3 pilot bearing, release bearing 833085M2 (Note: This Release Bearing is 2.49 inches I.D., 4.10 inches O.D., .875 inches wide, 1.535 inches front to back.), and 10 spline x 1 1/8 inch pilot tool. (Item #: 184827, Ref: M185923N833085) $210.00

Clutch Kit, 11 inch - Our new 11 inch double clutch kit includes: 11 inch, 25 spline, double pressure plate assembly with medium springs (532320M91); 11 inch, 10 spline rigid drive disc (516068M92); new pilot (C5NN7600A) and release (83914247) bearings, and clutch alignment tool. For tractor models 150, 165, 175, 175 UK, 178 UK, 180, 20C, 2135, 235, 245, 255, 265, 30, 30B, 30D, 3165, 35, 40B, 50, 65, 97. (Item #: 111060, Ref: 1212-1465) $300.00

Clutch Kit, 11 inch - Our new 11 inch dual clutch kit contains: 11 inch, MEDIUM SPRINGS, double pressure plate assembly with a 9 inch, 10 spline captive PTO disc (526665M91); 11 inch, 10 spline, 1 1/8 inch hub, rigid drive clutch disc (516068M92); pilot (832960M3) and release (892862M2) bearings, and clutch alignment tool. For the following AGRICULTURAL tractor models with MEDIUM TENSION SPRINGS: 150, 165, 175, 175 UK, 178 UK, 180, 20C, 2135, 235, 245, 255, 265, 30, 30B, 30D, 3165, 35, 40B, 50, 65, 97. ***Additional $20.00 shipping due to weight. *** (Item #: 112314, Ref: 1212-1417) $320.00

Clutch Kit, 11 inch - Our new 11 inch dual clutch kit contains: 11 inch, 10 spline double pressure plate assembly with heavy duty springs (526664M91); 11 inch, 10 spline rigid drive disc (516068M92); pilot (832960M3) and release (892862M2) bearings, as well as a clutch alignment tool. This kit has HEAVY TENSION SPRINGS for INDUSTRIAL use on the following tractors: 50, 165, 175, 175 UK, 178 UK, 180, 20C, 2135, 235, 245, 255, 265, 30, 30B, 30D, 3165, 35, 40B, 50, 65, 97. This Clutch Kit weighs 57 pounds. (Item #: 111063, Ref: 1212-1426) $310.00

Clutch Kit, 11 inch, Fine Spline - Our new 11 inch complete clutch kit contains: 11 inch, 25 spline, 1.625 inch hub, standard spring, double pressure plate (532319M91). 11 inch 10 spline, rigid drive disc (516068M93). 9 inch 1 3/4 inch hub PTO disc. Pilot bearing measuring 1.57 inches outside diameter, 0.669 inch inside diameter, 0.472 inch width (832960M3). Release bearing measuring 4.06 inches outside diameter, 2.49 inches inside diameter and 0.870 inch width (892862M2). Clutch alignment tool. For tractor models 135, 150, 165, 175, 175 U.K., 178 U.K., 180, 20, 20C, 2135, 235, 245, 255, 265, 30, 3165, 35, 50, 65, 97, TO35. (Item #: 111060, Ref: 1212-1420) $300.00

Clutch Kit, Dual, Coarse Spline - Includes NEW: 526666M91 Pressure Plate is 11 inch and 10 spline, 516068M93 Clutch Disc is 11 inch and 10 spline, Release and Pilot bearings, and clutch alignment tool. Fits the following tractors that use a 10 spline PTO disc: 135, 150, TO35. This part is for a late production T035 (Serial number 177537 and above). This unit will not fit early production TO35 with stamped finger clutch. Not for Deluxe models. (Item #: 111063, Ref: 1212-1400) $310.00

No
Picture
Clutch Kit, Remanufactured, 516068M93 - For Massey Ferguson tractor models F40, TO30 (S/N 177395-177519 and S/N 177538-later), TO35 (S/N 177395-177519 and S/N 177538-later), 35 (S/N 245087-later), 50, 65, 135, 150, 2135, Compatible with Massey Ferguson Construction and industrial models 20 (IND S/N DC2061-later), 202, 203, 302, 304, Replaces Massey Ferguson OEM number 516068M93, 526665M91, Clutch Diameter - 11", Clutch Hub Diameter - 1-1/8", Clutch Splines - 10, Clutch Center - Solid Offset, Clutch Type - Woven, Pressure Plate Size - 11", Pressure Plate Levers - 3, Pressure Plate Springs - 9, Pressure Plate Hub Diameter - 1-3/4", Pressure Plate Splines - 10, For a New version of this sku use Item #: 122859, Additional Handling and Oversize Fees Apply To This Item, (Item #: 202053) $410.01

Clutch Plate - 7.88 inch diameter, 1.250 inch spline diameter, 10 spline. For tractor models (300 up to serial number 116700051), (35 serial number 91500405 and up), 35 Super, 80, 82, 92, Super 92. (Item #: 172332, Ref: 1506025M91) $73.00

Clutch Release Bearing Carrier Spring - This Clutch Release Bearing Carrier Spring is used on many Massey Ferguson models. It is 2-1/8 Inch Overall Length. It replaces 1867690M1, 193334M1, 509230M2, 180451M1, 509230M2, 180451M2, 1867690M2. (Item #: 128535, Ref: 1867690M2) $4.20

Clutch Release Carrier Fork Locking Screw - This Clutch Release Carrier Fork Locking Screw is used to secure the release fork to the shaft on many Massey Ferguson models. Two used per tractor. Sold individually. It replaces Massey numbers: 881114M1, 881144M1, 881144M2, 3771408M1, 3790757M1, 180002M1 (Item #: 182943, Ref: 881144M1) $5.20

Clutch Release Fork - For tractor models 1200, 135, 135UK, 148, 155, 158, 165, 168, 175, 178, 185, 188, 20C, 20D, 20E, 20F, 230, 231, 235, 240, 245, 250 Brazilian, 253, 255, 261, 265, 270, 275, 282, 283 Brazilian, 290, 292 Brazilian, 297 Brazilian, 298, 299 Brazilian, 30B, 30D, 30E, 30H, 35, 35X, 375E Brazilian, 390E Brazilian, 40B, 40E, 415 Brazilian, 425 Brazilian, 435 Brazilian, 440 Brazilian, 445 Brazilian, 460 Brazilian, 465 Brazilian, 475 Brazilian, 481 Brazilian, 492 Brazilian, 50, 50A, 50B, 50C, 50D, 50E, 50EX, 50F, 50H, 60H, 65. Replaces 886719M1, 184628M1 (Item #: 179512, Ref: 886719M1) $58.00

Clutch Release Shaft - For tractor models 1200, 135, 135UK, 148, 165, 168, 175, 178, 178UK, 185, 188, 20C, 20D, 20E, 20F, 230, 231, 235, 240, 245, 250, 253, 255, 261, 265, 270, 275, 282, 283, 290, 298, 30B, 30D, 30E, 30H, 35, 35X, 375E, 390E, 40, 40B, 40E, 50, 50A, 50B, 50C, 50D, 50E, 50EX, 50F, 50H, 60H, 65, TO35, MH50. This Shaft is 1 inch diameter X 3 19/32 inches long. (Item #: 165437, Ref: 180449M1) $9.20

Clutch Release Shaft - For tractor models FE35, TO35, 165, 180, 20F, 240, 250, 270, 275 UK, 290 UK, 35, 40E, 50, 50E, 65. This shaft is 1 inch diameter x 5 17/32 inches long. Also replaces 1679460M1. (Item #: 166103, Ref: 180444M2) $9.70

Clutch Spring - For tractor models 135, 148, 165, 168, 175, 178, 185, 188, 240, 250, 265, 275, 290, 35, 375, 390, 398, 550, 565, 575, 590, 595, 65, 675, 690, 698. All with multi power transmissions. (Item #: 169497, Ref: 186519M1) $3.90

Clutch Transmission Disc11 Inch - This is an 11 inch rigid disc with a 10 spline, 1.125 inch hub. It is used in single clutch and split torque clutches. 165, 175, 180, 202 Indust/Const, 203 Indust/Const, 2135 Indust/Const, 2200 Forklift, 2200 Gas, 2500 Forklift, 255, 265, 30 Indust/Const, 31, 3165 Indust/Const, 35, 40B Indust/Const, 4500 Forklift, 50C Indust/Const, 50D Indust/Const, 65 Replaces 189948M91, 513580M92 (Item #: 130134, Ref: 189948M91) $100.00

Pilot Bearing - Clutch pilot bearing, heavy-duty, long lasting stainless steel. Bore: 0.670 inches (17mm), OD: 1.57 inches (39.88mm), 0.470 inches width. For tractors: MF50, MF65, MF85, MF88, MF235, MF245, MF255, MF285, MF1080 industrials: 20, 20C, 30, 30B, 31, 35 utility and turf, 40, 40B, 50, 50A, 50C, 202, 203, 204, 205, 302, 304, 2135, 2200. Replaces 832953M3, 1440487X1, 828123M1, 828123M2, 832960M3 (Item #: 107933, Ref: C5NN7600A) $3.40

Pilot Bearing - This Pilot Bearing measures .669 inches inside diameter, 1.575 inches outside diameter and is .472 inches wide. For tractor models 285, 290, 298, 30, 302, 30B, 30D, 30E, 30H, 31, 3165, 340, 342, 35, 350, 352, 355, 360, 362, 365, 375, 382, 390, 390T, 398, 399, 40, 40B, 40D, 40E, MH44, 50, MH50, 500, 50A, 50B, 50C, 50D, 50E, 50EX, 50H, 50HX, 560, 565, 575, 590, 592, 595, 60H, 65, 670, 675, 690, 698, 698T, 699, 85, 88, F40, FE35, Super 90, TE20. Replaces OEM part number 828123M2. (Item #: 107933, Ref: C5NN7600A) $3.40

Pressure Plate - Clutch pressure plate, external lugs for multi-power transmission, 3 required. For tractors: MF35, MF50, MF65, MF135, MF150, MF165, MF175, MF180, MF235, MF240, MF245, MF255, MF265, MF275, MF290, MF298, MF375, MF390, MF398 industrial: 30. For 20D, MF135, MF165, MF175, MF180, MF235, MF240, MF245, MF255, MF265, MF275, MF35, MF50, MF65, TO35 (Item #: 155473, Ref: 185464M1) $9.50

Pressure Plate, 11 Inch - For 20C, 20, 30B, 30D, 30, 40B, 40, MF135, MF150, MF165, MF175, MF180, MF230, MF235, MF245, MF255, MF265, MF35, MF50, MF65, TO35 (Late production) (Item #: 182796, Ref: 1040884M1) $82.00

Pressure Plate Assembly - For Massey Ferguson tractor models TO35, 35, 50 (s/n 515433 - later), 135, 150, 2200, Compatible with Massey Ferguson Construction and industrial models 20 (Transmission s/n DC2062 - earlier), 40, 202, 203, 2135, Replaces Massey Ferguson OEM number 886384M91, 1034195M92, 184541M91, 193930M92, 512355M91, 526666M91, 526666V91, 533795M91, 886384M93, Pressure plate size: 11", Pressure plate levers: 3, Pressure plate springs: 6, Pressure plate hub: 1-3/4", Pressure plate splines: 10, Pressure plate type: Dual stage, For 12 spring pressure plate use Item #: 122846, (Item #: 169256) $304.00

Pressure Plate Assembly, Remanufactured - For Massey Ferguson tractor models TO30, TO35, 35, 50, 65, 135, 150, 202, 203, 302, 304, 2135, 2200, Pressure Plate Size: 11", Pressure Plate Levers: 3, Pressure Plate Springs: 9, Pressure Plate Hub: 1-3/4", Pressure Plate Spline: 10, Pressure Plate Type: Dual Stage, (Item #: 206883) $240.01

Pressure Plate Assembly, Remanufactured, 1034195M92 - For Massey Ferguson tractor models TO35, 35, 50 (s/n 515433), 135, 150, 2200, Compatible with Massey Ferguson Construction and industrial models 20 (Transmission s/n DC2062 - earlier), 40, 202, 203, 2135, Replaces Massey Ferguson OEM number 1034195M92, 184541M91, 193930M92, 512355M91, 522666M91, 533795M91, 886384M91, 886384M93, Pressure Plate Size: 11", Pressure Plate Levers: 3, Pressure Plate Springs: 12, Pressure Plate Hub: 1-3/4", Pressure Plate Spline: 10, Pressure Plate Type: Dual Stage, For a New version of this sku use Item #: 122846, Additional Handling and Oversize Fees Apply To This Item, (Item #: 206853) $273.01

Pressure Plate Assembly, Remanufactured, 180263M91 - For Massey Ferguson tractor models TE20, TEA20, TO20, TO30, TO35, 35, 50, 135, 202, 203, 2135, Replaces Massey Ferguson OEM number 180263M91, 185923M91, Pressure Plate Size: 9", Pressure Plate Levers: 3, Pressure Plate Springs: 6, Pressure Plate Type: Single Stage, For a New version of this sku use Item #: 119390, (Item #: 206881) $111.01

Pressure Plate Assembly, Remanufactured, 184543M91 - For Massey Ferguson tractor models TO30, TO35, 35, 50, 65, 135, 150, 202, 203, 302, 304, 2135, 2200, Compatible with Massey Ferguson Construction and industrial models 40, Replaces Massey Ferguson OEM number 184543M91, 193931M92, 512356M91, 526665M91, Pressure Plate Size: 11", Pressure Plate Levers: 3, Pressure Plate Springs: 9, Pressure Plate Hub: 1-3/4", Pressure Plate Spline: 10, Pressure Plate Type: Dual Stage, For a New version of this sku use Item #: 122859, Additional Handling and Oversize Fees Apply To This Item, (Item #: 206884) $259.50

Pressure Plate Cover Assembly, 9 inch single - Pressure Plate Assembly - 9 inch single. (Rockford) For the following tractors using Continental Z120, Z129 or Z134 engines: MF 135, 205, 20C, 2135, 35, 50, 72, 82, F40, MH20, MH30, TO20, TO30, TO35. (Item #: 119390, Ref: 180263M91) $155.00

PTO Disc, 9.055 - 9.055 inch rigid disc, organic, spline diameter 1.75 inch 10 spline. For tractor models 130, 135, 165, 175, 180, 20, 202, 203, 2135, 2165, 2200, 245, 25, 255, 265, 290, 30, 302, 30B, 30D, 3165, 35, 40B, 50 serial number 515396 and up, 65, TO35 serial number 177395-177519 and 177538 and above. All with dual clutches. Replaces 1034195M1, 1539020C1, 1753753M1, 1753753M94, 1753753M94-A, 181102M92, 1851652M92, 323022046, 323022047, 3620411-RF, 3620411-RO, 3620411M1, 3620411M91, 392492R91, 709640R92, 899823M91. (Item #: 163114, Ref: 323022047) $52.00

PTO Disc, 9 Inch - 10 spline on 1.750 inch hub. For tractor models 135 dual, 165 dual, 175 dual, 180, 20 dual, 202 dual, 203 dual, 204, 2135 dual, 2165 dual, 2200 dual, 30, 302 dual, 30B dual, 3165 dual, 35 dual, 50, 65, F40 dual, TO35 dual. Replaces 1753753M91, 1753753M92, 1753753M93, 1753753M94, 3620411M91, 3620411V91 (Item #: 113815, Ref: 1753753M94) $49.07

Release Bearing - Bearing, clutch release, 2.49 inch inside diameter, 4.10 inch outside diameter, 1.5265 inches wide. For single clutch tractors: TO35, MF35, F40, MF50, MF65, MF135 industrials: 2135, 3165. (A2336-37/A2336-147) For 2135, 3165, F40, MF135, MF35, MF50, MF65, TO35, 202, 203, 302, 304. Replaces 833085M1, 833085, 180505M2, N2336-147 (Item #: 168448, Ref: 833085M2) $169.00

Release Bearing - Sealed Release Bearing for single and dual clutch, 2.50 inch inside diameter, 3.936 inch outside diameter. For tractor models 1080, 1085, 1100, 1130, 130, 133, 135, 140, 145, 148, 150, 152, 155, 157, 158, 165, 168, 175, 177, 178, 180, 185, 188, 20, 202, 203, 204, 205, 20B, 20C, 20D, 20E, 20F, 20H, 2135, 2165, 2200, 220, 230, 235, 240, 245, 250, 255, 260, 265, 270, 275, 282, 285, 290, 298, 30, 302, 30B, 30D, 30E, 30H, 31, 3165, 340, 342, 35. Replaces original part numbers 892862M2, 892862M1, 86534551 and 195508M1. (Item #: 112189, Ref: N1585) $24.70

Release Bearing Carrier - Carrier, for clutch release bearing. Carrier bore 2.130 inch (2-1/8 inch approximate); outside diameter 2.503 inch (2-1/2 inch). PLEASE CHECK CARRIER BORE BEFORE ORDERING. For single or dual clutch. Tractors: TO35, MF35, MF50, MF65. Industrials: 20, 202, 203, 302, 2135. Use with bearing 892862M2 for DUAL CLUTCH ONLY. This is the old style for retainers with bronze bushing. (Item #: 165363, Ref: 183129M2) $24.10

Release Lever - For tractor models 150, 20C, 20, 30B, 30D, 30, 40B, 40, MF135, MF150, MF165, MF175, MF180, MF230, MF235, MF245, MF255, MF265, MF35, MF50, MF65, TO35. (Item #: 182186, Ref: 899818M2) $17.50

Cooling System

Fan, 6 Blade - 15.250 inch diameter, 1.0625 inch pilot hole, 1.750 inch bolt hole center to center. For tractor models 150, 202, 204, 2200, 35, 50, TE20, TO20, TO30, TO35. With Continental Gas Engine. (Item #: 121690, Ref: 181522M91) $64.00

Fan Belt - This fan belt measures 17/32 inches wide and 49.27 outside diameter. For tractor models: MF35, (MF135 to serial number 9A38905), (MF150 with generator), MF165. All with Diesel Engines. (Item #: 173292, Ref: 186976M1) $10.10

Fan Belt - 46 inches length. For Diesel models: 274C, 35, 353, 363, 373, 377, 383, 387, 393, 397, 65, 765. Fan Belt also replaces 1851751M1, 2614B642, 1851749M1, 0070078, 0070172, 2612417, 2614B142. (Item #: 123125, Ref: 3637595M1) $10.80

Fan Belt - Outside length 42.5 inches long. For tractor models TO35 4 cylinder gas, 35 4 cylinder gas, 50 4 cylinder gas, 150 4 cylinder gas, MH50 4 cylinder gas, 2500 diesel, 202 4 cylinder gas, 204 4 cylinder gas, 2135 4 cylinder gas, 2200 4 cylinder gas, 302 4 cylinder gas, 304 4 cylinder gas, 135 4 cylinder gas. Replaces 509572M1GV, 181523M1, 189865M1, 191442M1, 509572M91, 509572V1. (Item #: 151990, Ref: 509572M1) $12.70

Fan Blade - This fan is 4 blade, 15 inch diameter, 1 1/16 inch pilot hole. For Continental Gas Engine models 135, 150, 202, 204, 2200, 35, 50, TE20, TO20, TO30, TO35. (Item #: 121691, Ref: 181522M91-4) $59.00

Fan Blade - Replaces 825181M91. 15 1/2 inch diameter fan fits: (35, 50 both with Perkins Diesel), (TE20, TEA20 both with 80, 85, or 87mm Gas), (TO35 with 23C Diesel), (FE35 with 87mm Gas or 23C Diesel). Fan Blade, trapezoidal bolt pattern. Bolt pattern 1 1/4 inch between top holes, 1 1/2 inch between bottom holes, 5/16 inch holes with 1 1/8 inch center cutout. (Item #: 121692, Ref: 186819M91) $30.50

No
Picture
Gasket - For Massey Ferguson tractor models 20, 35, 35X, 40, 50, 135, 150, 154-4, 205, 230, 235, 240, 240P, 245, 250, 254-4, 302, 304, 364S (s/n D03066-early), 2135, 2200, Compatible with Massey Ferguson Construction and industrial models 20C, 20D, 20E, 20F, 30B, 30D, 30E, 30H, 40E, 2200, 2500, 4500 Replaces Massey Ferguson OEM number 731210M1, , Compatible with Massey Harris tractor models 50, (Item #: 160354) $4.70

Gasket, Thermostat Body - For tractor models TO20, TO30, TO35, MF35. (Item #: 173218, Ref: 181528M1) $0.78

Gasket Thermostat Or Water Outlet Elbow - Gasket, water outlet elbow. Tractors: TO35, MF35, and MF50. (Item #: 155327, Ref: 181526M1) $0.98

Hose Clamp - This hose clamp is used as a radiator hose and a air cleaner hose. It fits hoses with an outside diameter 1 3/4 inches to 2 inches. Check hose diameter before ordering. (Item #: 178164, Ref: 608287) $3.80

Radiator - For tractor models FE35, TO35, MF135, MF203, MF205, MF35 and MF35 UK. All with A3.152 Perkins Diesel engines. It is 17.5 inches tall and the core size is 15 inches wide. Replaces: 186732M91. OVERFLOW TUBE AND PETCOCK NOT INCLUDED. (Item #: 101792, Ref: 894319M92) $200.00

Radiator - For tractor models 20 and 2135 Industrial with Perkins Gas or Diesel. For 135 gas and diesel, 135 UK gas, 148 with diesel. Core measures 18.5 inches high, 15 3/8 inches wide. 135 Vineyard with Perkins Gas serial number 9A117590 and up and with diesel serial number 9A117610 and up). Replaces 194275M94, 194275M93, 1660499V94, 186732M91, 1660499M92, 885856M94, 897188M94, 897188M91. (Item #: 101794, Ref: 194275M93) $220.00

Radiator - For Massey Ferguson tractor models 35, 35X (FE, Engine s/n 7704-later), Replaces Massey Ferguson OEM number 894357M92, 828108M91, Core Width: 15.125", Core Height: 17.375", 3 Rows of Tubes, 8 Fins per Inch, (Item #: 162335) $363.00

Radiator - For tractor models TO35 (serial number 204181 and above), 35, 35 TURF, 35 Utility, and 202 Industrial (serial number 306493 and above). All with gas engines. Weight 18.5 pounds. Core size (the finned part) is 15.12 inches wide by 17.12 inches high, has 3 rows of tubes, total height is 23.5 inches from top of tank to bottom of tank. (Item #: 101791, Ref: 186830M91) $200.00

Radiator, Bypass Hose - .906 inch inside diameter. For tractor models 35, 35X, TO35. (Item #: 159588, Ref: 826199M1) $6.80

Radiator Cap - 7 pound pressure radiator cap. Cap measures 2.328 inches diameter less finger tabs. Inside diameter is 2.215 and 1.970 inches between locking tabs. Replaces 184528M1, 184528M91, 184528M1. Fits 135, 150, 165, 175, 180, 235, 240, 255, 35, 50, MH50, 65, 85, 88, TO20, TO30, TO35. (Item #: 112331, Ref: 180224M91) $6.60

Radiator Hose Lower - Hose, radiator lower. For Perkins Diesel Engine in tractors: MF35, MF135, MF230, to serial number 9A243032, MF235 except Orchard Industrials: 20, 35 utility, 202, 203, 205, 2135. (Item #: 159314, Ref: 186968M1) $9.30

Radiator Hose, Lower - Hose, radiator lower. For Continental Gas Engine in tractors: TO35, MF35, MF135 industrials: 202, 204, 2135. 1.85 inch outside diameter, 1.50 inch inside diameter, 10.70 inches long. For 135, 202, 204, MF135, MF150, MF35, TO35. (Item #: 108421, Ref: 180783M1) $8.70

Radiator Hose - Upper - For Massey Ferguson tractor models TO35 (s/n 204181-later), 35, 135 (UK), 230, 231, 240, 241, 250, 253, 265, 275, 565, 575, Replaces Massey Ferguson OEM number 186826M1, Replaces JCB OEM number CTJ3105, 10329404, Fits Engines: 4.236 and A4.236, ID: 1.375", ID: 1.437", Length: 6", For Hose Clamp use Item #: 130453, (Item #: 108423) $7.80

Radiator Hose, Upper - 5 1/2 inches long and 1 1/2 inches diameter. For tractor models TE20, TO20, TO30, TO35, F40, (50, 65 with Continental Engine), (35, 50, with Perkins Diesel), (135 with Perkins Gas or Diesel), (230 serial number 243032 and up), (235 with Perkins Diesel), 20, 2135, 50, 2500 gas Z120, Z129, Z134. PLEASE NOTE: You may receive a longer piece up to 8 1/2 inches long and you can cut-to-fit. (Item #: 110453, Ref: 180085M1) $6.00

Radiator Hose, Upper - New upper radiator hose with an inside diameter of 1.5". This radiator hose fits the Massey Ferguson Tractor 35 (with A3.152 engine). (NOTE: replaces VPE 4045) (Item #: 159605, Ref: 890195M1) $6.50

Radiator Mounting Pads, Pack of 2 - This pack of 2 radiator mounting pads is for tractor models 135, 20, 2135, TO35, 35, 230, (235, 245 except orchard), 240, 250, 253, 20C turf, 20D, 30E, 35, 40E, 202, 203, 204, 205. Two are used per tractor on the bottom of the radiator. (Item #: 109978, Ref: 180705M1) $2.50

Thermostat - Thermostat. For Continental Gas Equipped tractors: 2200, 202, 204, 2135, 3165, F40, TO35, 50, 2500, 302, 304, 356, 135, 150, 165, 175, 180, 35, 65, 35, Colt, MH21, MH20, MH22, MH50. 160 degree. Comes with gasket. Replaces 830842M91, 836000V91, 836000M1, 830842M91, 830685M91, 184406V2, 181566M1 (Item #: 108422, Ref: 836000M91) $14.50

Thermostat,180 Degree - For: F40, FE35, TEA20, 150, Deluxe, TO35, 1080, 1085, 1100, 1105, 1130, 1135, 130, 135, 148, 150, 154, 1545, 165, 168, 175, 187, 185, 188, 20, 202, 203, 204, 205, 20C, 20D, 20E, 2135, 2200, 2244, 230, 235, 240, 245, 250, 2500, 253, 254, 255, 265, 275, 285, 290, 298, 30, 30B, 30E, 30H, 320, 35, 350, 35X, 360, 362, 40, 40E, 4500, 470, 4830FC. Replaces 1446165V91, 1446127M1, 1446165M1, 1446127V91, 2485648, 1894961M1, 2485659, 325505M2, 32550, 1446165M91, 1446127M91, 2485666, 40085, 826306M1, 828139M1, 886000M1 (Item #: 110084, Ref: 1446165M91) $7.40

Thermostat Body Cap - For 135, 20, 202, 203, 205, 20D, 20C, 20F, 2135, 2200, 230, 231, 235, 240, 245, 250, 2500, 253, 30B, 30D, 30E, 30H, 35, 4040E, 4500. Thermostat Body Cap (Perkins Diesel) also replaces 37747581. (Item #: 155437, Ref: 731000M1) $34.64

Thermostat Housing - Thermostat housing also replaces 37766361. For tractor models 135, 150, 154-4, 1545, 20, 200, 203, 205, 20C, 20D, 20F, 2135, 2200, 2244, 230, 231, 235, 240, 240P, 245, 250, 2500, 254-4, 30B, 30D, 30E, 30H, 35, 40, 40E, 4500, 4830FC, 50, 5830, 5830FC, 5860, 5870. Replaces 746835M1, 37766361, 37766362, 37766363, 737192M1. (Item #: 173276, Ref: 746835M1) $68.00

Upper Radiator Hose - New upper radiator hose with an inside diameter of 1.532 inch and 8.625 inch in length. This radiator hose fits multiple Massey Ferguson Tractor models. (Item #: 134505, Ref: 182345M1) $8.50

Water Pump Gasket - This Gasket is for 3641250M91 and other water pump backplates. Fits models 1004, 1014, 1080, 135, 148, 165, 168, 174, 175, 178, 184, 185 BACKHOE, 188, 194, 230, 240, 250 SKID STEER LOADER, 254, 255, 265, 273, 274, 275, 283, 284, 285, 290, 293, 294, 340, 342, 35, 350 INDUST/CONST, 352, 355, 360, 362, 372, 373, 374, 375, 377, 383, 384, 387, 390, 393, 394, 397, 550, 560 COMBINE, 565 COMBINE, 575 SKID STEER LOADER, 590, 595, 675, 690, 698. Replaces 3638177M1, 4224122M1, 4224387M1, 731165M1. (Item #: 163938, Ref: 4224387M1) $2.10

Water Pump Gasket - Used on Perkins 144 and 152 cubic inch, three cylinder engines. Replaces 957E8507, 72080255, 0941183, 731275M1, 4222931M1, 36862532 (Item #: 155091, Ref: 4222931M1) $8.10

Water Pump Gasket - For Massey Ferguson tractor models F40, TO35, 35, 50, 135, 150, 230, 235, 245, 2200, Compatible with Massey Ferguson Construction and industrial models 20C, 30B, 202, 203, 204, 205, 2135, 2200, 2500, 4500, Replaces Massey Ferguson OEM number 1750079M2, (Item #: 163002) $2.30

Water Pump Housing to Block Gasket - Used on Continental Engines, this gasket goes between the water pump housing and engine. Used on Massey Ferguson models: 20C, 202, 204, 2135, 30B, TE20, TO20, TO30, TO35, 135, 150, 230, 235, 245, 35, 50 (Continental Gas only) (Item #: 173646, Ref: 1750077M1) $2.30

Water Pump Pulley - Single groove. For tractor models (135UK serial number up to 152UA5275D), (35, 50 all with Perkins Diesel Engine), (203, 205 all with Regular Diesel Engine). (Item #: 116876, Ref: 731280M1) $45.45

Water Pump Pulley - For TO35, 35, 135, 202, 204, 230, 235, 245, 2135, 2200. All with CONTINENTAL Gas engines. (Item #: 111273, Ref: 1750081M1) $44.00

Water Pump, Remanufactured, Z129K42 - For Massey Ferguson tractor models TO35, 35, 50, 135, 150, 202, 204, 230, 235, 245, 2135, 2200, 2220, 2500, Compatible with Massey Ferguson Construction and industrial models 20, 30, 40, 50, Compatible with Massey Harris tractor models 50, Replaces Casting number Z129K42, Impeller 2-3/4", Includes Mounting Gasket, Without pulley or hub, (Item #: 206975) $54.01

Water Pump, without pulley - This pump has a 2 3/4 inch impeller. For tractor models 35, TO35, F40, 35, 50, MH50, 202, 204, 2135, 2200, 2500 forklift, All with Z134 Continental gas engine. Includes gasket. Works with 1750081M1 or 1751852M1 pulley, depending application. Replaces original part numbers 830691M91, 830691M1, 830691M91-R, 830514M91. (Item #: 101970, Ref: 830691M91) $41.20

Water Pump with Pulley - For tractor models 135 UK, 150, 203, 205, 35, 50, FE35. Water Pump with single pulley and gasket. 2.5 inch diameter hub. Replaces Perkins 41312154. Includes pulley part number 731280M1 2.5 diameter hub. The fan mounting bolt holes are not in a square pattern. For Perkins A3.152 Diesel. Replaces 731280M1, 747542M91, 829258M1. (Item #: 122905, Ref: 734932M91) $54.00

Water Pump - With Pulley - This new water pump includes pulley part number 735034M1 with 3.125 inch hub diameter and a 1 5/8 inch pilot. The pulley has a square fan pulley mounting pattern. For tractor models 35, 50, 135, 150, 203, 205, 235, 245, 240, 20, 20C, 20E, 20F, 2135, 230, 231, 240, 245, 253, 360, 154-4, 30B, 30D, 30E, 30H, 40E, 2500, 254-4 all with PERKINS AD3.152 or AG3.152 engines. This is a new water pump. Replaces 3641338M91, 3641823M91, 37711330, 739527M91, 747542M91, U5MW0023, 41312487, 4132159, 735034M1, 735034V1, 747542M9. (Item #: 150185, Ref: 3641823M91) $37.00

Water Pump, With Pulley - This Water Pump has a 2 3/4 inch impeller. For tractor models 35, TO35, F40, 35, 50, 135, 202, 204, 230, 2135, 2200, 2500 forklift, All with Z134 and Z145 Continental gas engine. Includes gasket. Replaces 1750081M1 pulley and 830691M91 pump. (Item #: 184540, Ref: 830691M91_WP) $105.00

Decals and Emblems

Decal Set - For 35 Deluxe. Complete decal set. (Item #: 183480, Ref: R4312) $45.30

Decal Set - For MF 35 Hood. Set of 5 self adhesive decals. (Item #: 183542, Ref: R1353) $40.90

No
Picture
Decal Set - For model 35 Special. Complete decal set. (Item #: 184828, Ref: D-MF35) $41.80

No
Picture
Decal Set - For 35 Deluxe. Complete decal set. Vinyl cut (individual letters are cut out). Made of vinyl. (Item #: 102544, Ref: R4312V) $123.00

Decal Set - For 35 Diesel Deluxe. Complete decal set. (Item #: 183239, Ref: R3918) $45.30

Engine Serial Number Tag, Blank - Comes with 4 rivets, black anodized aluminum, 3.885 inches long, 1.885 inches high, customer must stamp the number. For tractor models TO35, 35, F40, Early 135, 202, 203, 204, MH50, 2135. For all models with 4 cylinder Z134 Continental Gas Engine. (Item #: 178545, Ref: MFSNTAG) $33.90

Front Emblem - This Front Emblem comes with clips. It is used on Massey Ferguson 35 Tractors. Replaces (Item #: 105345, Ref: 187990M1) $105.00

Hood Emblem - For MF35 and (TO35 Serial number 176341 and up). Front Emblem "Ferguson" shield. Chrome, red background. Replaces: Casting Number: 180661M1, 183194M2 (Item #: 104110, Ref: R3215) $60.00

Side Emblem - For tractor models TO35, MF35. Side Emblem. "Ferguson-35". Metal. Sold individually. Chrome, red background. 1-1/4 inch x 9-7/8 inch. Includes mounting clips. Attaches with 3 pegs. Replaces OEM number 183193M1. (Item #: 104113, Ref: R3213) $34.00

Drive Train

Massey Ferguson 35 6 Speed and Multi-Power Selector Parts

6 Speed and Multi-Power Selector Parts - Click on picture to view parts. ONLY parts that have a corresponding number are available. Some parts work only with specific serial number ranges within a particular tractor model. Not all parts work with this tractor model. Call for application and availability.

NOTE

Axle Collar - For tractor models MF135, MF150, MF35, MF50, TO35. (Item #: 108413, Ref: 180596M1) $11.30

Ball Bearing - This is a main shaft rear and countershaft bearing used in many Massey Ferguson models. It measures: 50mm inside diameter, 90mm outside diameter, and 20mm wide. Confirm measurements or OEM part number before ordering. Replaces 195493M1, 391128X1, JD10011, 6210ZZ, 6210, 851-6210ZZ (Item #: 173672, Ref: 195493M1) $23.80

Ball Bearing - Bearing, ball, for countershaft front. Also used for multi-power mainshaft front. Replaces 831469M1. For MF135, MF150, MF165, MF175, MF180, MF35, MF65, TO35 (Item #: 169628, Ref: 195507M1) $23.70

Bearing Cone - Cone (53177) for differential. For tractors: TO35 serial number 169467 and up MF50 using sleeve 181251M92 MF35, MF135, MF150, MF165, MF175, MF180, MF235, MF255, MF265, MF275. 1.75 inch bore. 1.114 inch bearing width. (Item #: 182661, Ref: 195163M1) $149.00

Bearing Cone - Cone (HM903249), for differential. For tractors: TO35 serial number 169467 and up, using sleeve 181251M93 MF35, MF65 serial number CL2686122 and up, MF165, MF180 using sleeve 190606M92 MF175, MF235, MF255, MF265, MF275. 1.750 inch bore, 1.125 inch bearing width. (Item #: 117943, Ref: 831888M1) $30.40

Bearing Cone - Rear Axle Outer Bearing Cone. For tractor models MF135, MF150, MF35, MF50, TO35. (Item #: 128533, Ref: 195675M1) $36.40

Bearing Cup - Single cup (53375) for differential, two used. For tractors: MF35, MF135, MF150, MF165, MF175, MF180, MF235, MF255, MF265, MF275. (Item #: 172732, Ref: 17392A) $60.02

Bearing Cup - Double tapered cup (53376D) for differential. For tractors: TE20, TO20, TO30, TO35 prior to serial number 169467 MF35, MF50 using sleeve number 181251M91 also MF65 to serial number CL2686121 MF135, MF150, MF165, MF175, MF180. (Item #: 180440, Ref: 181251DTC) $344.00

Bearing Cup, Axle Hub - Bearing Cup - Axle Hub. For tractor models MF135, MF150, MF35, MF50, TO35. Replaces 195676M1, 300975M1, 300975M91, JD7439, A453X, 300975V1 (Item #: 108414, Ref: 300975M1) $14.40

Bearing Cup, Rear Axle, LH Inner - This Left Hand Bearing Cup measures 4.438 inch outside diameter and .938 inch width. Fits models 135, MF150, MF165, MF175, MF180, MF235, MF255, MF265, MF275, MF35, MF50, MF65, TO20, TO30, TO35. (Item #: 116984, Ref: 195160M1) $18.70

Bearing, Input Drive Shaft - Bearing, ball, input drive shaft. Inside diameter 1.574 inches, outside diameter 3.150 inches, width .709 inches. For tractor models TO35, MF35, 50, 65, 135, 150, 165, 175, 180. (Item #: 172367, Ref: 195505M1) $28.10

Bearing Kit - Needle Bearing Kit. For transmission reverse idler gear. Not for shuttle, instant reverse, or 12-speed transmissions. (1) required. For tractors: TO35 serial number 171549 and up, MF35, MH50, MF50, MF65, MF135, MF150, MF165, MF175, MF180, MF230, MF231, MF235, MF240. (Item #: 125327, Ref: 830735M91) $34.92

Bearing, Needle - Needle Bearing for countershaft. For 1080, 1085, 1200, 1250, 133, 135, 140, 145, 148, 150, 152, 158, 165, 168, 175, 178, 180, 185, 188, 20, 20C, 20D, 20E, 20F, 2135, 230, 231, 235, 240, 245, 250, 253, 255, 260, 261, 263, 265, 265 S (TR), 270, 275, 282, 283, 283 Brazilian, 285 (FR), 285 S (TR), 285 US Built, 290, 298, 30, 30B, 30D, 30E, 30H, 31, 3165, 340, 342, 35, 350, 352, 355, 35X, 360, 362, 365, 375, 375E Brazilian, 383, 390, 390E Brazilian, 390T, 393, 396, 398, 399, 40, 40B, 40E, 40H, 415 Brazilian, 4215, 4220, 4225, 4235, 4245, 425 Brazilian, 4255, 4260, 4265, 4270, 4315, 4325, 4335, 4345, 435 Brazilian, 4355, 4360, 4365, 4370, 440 Brazilian, 445 Brazilian, 475 Brazilian, 481 Brazilian, 50, 50B, 50C, 50D, 50E, 50EX, 50H, 50HX, 5340 Brazilian, 5355 Brazilian, 5360 Brazilian, 5365 Brazilian, 550, 560, 565, 575, 590, 592, 595, 60H, 60HX, 65, 65 US Built, 670, 675, 690, 698, 698T, 699, 765, 835, 865, Super 90, TO35, Massey Harris 50. Replaces 532883M1, 195453M1 (Item #: 167261, Ref: 195453M1) $10.70

Bearing, Needle - Needle Bearing, for power input pilot, multi-power. For MF135, MF150, MF165, MF175, MF180, MF35, MF65, TO35. 1 inch inside diameter, 1-5/16 inch outside diameter, 3/4 inch wide. (Item #: 116985, Ref: 195873M1) $7.60

Bearing, Outer Input Housing - 1080, 1085, 135, 150, 165, 175, 180, 20, 20C, 20D, 20E, 20F, 231, 235, 240, 245, 250, 253, 255, 261, 265, 270, 275, 282, 283, 285, 290, 298, 30, 30B, 30D, 30E, 30H, 31, 35, 35X, 360, 362, 375, 383, 385, 390, 390T, 393, 396, 398, 399, 40, 40B, 40E, 50, 50C, 50D, 50E, 65, 670, 690, 698, 699.Used on 1860889M1 retainer. (Item #: 165439, Ref: 886668M1) $11.80

Bearing, Pinion Pilot - For tractor models 135, 148, 155, 158, 165, 168, 175, 178, 185, 188, 230, 240, 250, 265, 275, 285 with 11 x 38 differential, 290, 340, 35, 350, 355, 360, 362, 365, 375, 390, 390T, 398, 399, 550, 565, 575 with 11 x 38 differential, 590 with 11 x 38 differential, 65, 675, 690 with 11 x 38 differential, 765, FE35. Replaces 191250M1, 191250V1, 196098M1 (Item #: 117942, Ref: 191250M1) $24.20

Bearing Seal and Collar Kit, Rear Axle - Contains (1) shrink-on collar 180596M1 (3 inch x 2-1/4 inch x 11/16 inch), (1) axle bearing (cup 300975M1 and cone 195675M1), (1) inner axle seal 195678M2 (2-1/8 inch x 2-7/8 inch x 1/2 inch), (1) outer axle seal 195677M1 (2-3/4 inch x 3-5/8 inch x 19/32 inch). Fits where the above parts are used: TO35, F40, 133, 135, 135UK, 140, 148, 150, 20, 20C, 20D, 2135, 230, 231, 235, 240, 245, 30, 3 165, 340, 35, 35UK, 35X, 50, 550. Verify part numbers. Some of these models were build with more than one rear axle. (Item #: 182552, Ref: S.05948) $100.00

Carrier Assembly - For Epicyclic Pinion Gear. Models: 135, 150, (155, 158, 165 with Multi Power), 175, 20, 202, 203, 20C, 20D, 20F, 2135, 2200, 230, 231, 235, 240, 240P, 245, 250, 2500, 253, 255, (265, 275, 285, 290 with Multi Power), 30, 302, 30B, 30D, 30E, 30H, 31, 3165, 35 serial number 365360->, 360, 362, 375, 40, 40B, 40E, 4500, 50, 50A, 50C, 50D, 50E, (550, 565, 575, 590 with Multi Power), 65, 6500, 765 serial number 609714->, FE135 Coventry. (Item #: 161568, Ref: 897711M93) $359.15

Countershaft - Countershaft, 6 speed and manual shuttle. 17/20 spline, 15 tooth. For the following tractors: 1080, 135, 150, 165, 175, 180, 20, 202, 203, 204, 205, 2135, 220, 2200, 230, 235, 245, 30, 35, 50, F40, FE135, TO35. (Item #: 178325, Ref: 183054M92) $192.22

Countershaft - Countershaft, 6 speed transmission. 20/17/10 spline, 15 tooth, 12.750 inches long. For the following tractors: 135, 202, 203, 204, 205, 2135, 2200, 3165 35, 50, 65, FE135, MH50, TO35. (Item #: 173663, Ref: 183085M1) $140.60

Countershaft Driven Gear - Countershaft Driven Gear, 6 speed trans. 50 tooth, 20 spline. For tractor models 135, 150, 20, 202, 2135, 2200, 230, 235, 245, 35, 50, F40, FE135, MH50, TO35. (Item #: 165905, Ref: 181799M1) $77.15

Countershaft, Transmission, 17 Spline, 15 Teeth - Shaft is 12.25 inches long. For MultiPower Transmissions on: 1080, 1085, 135, 148, 150, 155, 158, 165, 168, 175, 178, 180, 185, 188, 235, 240, 245, 250, 255, 265, 270, 275, 285, 290, 298, 30, 35, 50, 550, 565, 575, 590, 65, 765, FE135, FE35. (Item #: 173274, Ref: 189391M92) $224.00

Coupler - Coupler, 3-13/16 inches long, 10 spline, 1 groove, rear drive shaft to pinion. For tractors: MF230 serial number 9A349239 and up, MH240 to serial number 2773N01001, MF240 standard, MF68, MF50, MH50, TO35 serial number 169467 and up. Industrial: 20D. We suggest measuring the pinion spline length and length of coupler to determine if 1683757M91 (4-5/16 inches long) was previously installed and whether 1871192M1 coupler is needed. (Item #: 113799, Ref: 1871924M1) $14.00

Coupling, Wheel - 5.00 inch long, 3 groove, 10 spline. For tractor models 135, 148, 150, 155, 158, 165, 168, 175, 178, 188, 202, 203, 204, 205, 2200, 35, 365, 50, 65, 765, F40, FE135, FE35. (Item #: 160182, Ref: 880069M2) $38.10

Differential Bearing and Cup - Fits in Differential Lock. Bearing and cup is used on multiple Massey Ferguson Tractors. Replaces original part numbers: 1850087M91, 1850087M92, 1851533M91, 1851533V91, 185773M1, 185775M1, 185776M1, 1857775M1, 1857776M1, 195159M1, 195159V1, 195160M1, 195160V1, 300975M1. (Item #: 179801, Ref: 195159M1) $28.90

Differential Bearing and Cup RH - Bearing and cup set Fits multiple Massey Ferguson Models. (159x108x21mm) Replaces 1850849M91, 1850909M91, 185251M1, 185252M1, 185252V1, 3039248M1, 3039249M1 (Item #: 150360, Ref: 185251M1) $146.00

Differential Lock, Cam and Shaft Assembly - For tractor models 135, 150, 20, 202, 204, 20C, 20D, 2135, 2200, 230, 231, 235, 240, 240P, 245, 30, 3165, 35, 50, FE135, FE35. (Item #: 173127, Ref: 190960M92) $58.00

Differential Lock Cap. - 10 lug. For tractor models FE35, 135, 150, 20, 20C, 20D, 202, 204, 2135, 2200, 230, 231, 235, 240, 240P, 245, 30, 3165, 35, 50, FE135. (Item #: 172279, Ref: 190963M1) $94.00

Differential Pinion Gear - Verify that the gear you are replacing has 10 teeth and a 2.92 inch diameter. For tractor models 1100, 1105, 1130, 1135, 1150, 1155, 135, 150, 1500, 1505, 165, 175, 180, 1800, 1805, 203, 205, 2135, 2200, 2500, 302, 304, 3165, 35, 356, 40, 50, 65, 70, 80, 85, 88, Super 90. (Item #: 173507, Ref: 181275M1) $61.72

Differential Planetary Thrust Washer - Used on many Ferguson and Massey Ferguson models, this washer measures 3 inches inside diameter, 4 3/16 outside diameter and 0.053 inches thick. Used on 1080, 1100, 1105, 1130, 1135, 1150, 1155, 1200, 1250, 133, 135, 140, 148, 150, 152, 155, 158, 165, 168, 175, 178, 180, 185, 188, 20C, 20D, 20F, 2135, 230, 240, 250, 2620, 2640, 265, 2680, 2720, 275, 285, 290, 298, 30B, 30D, 3165, 340, 342, 35, 350, 352, 355, 360, 362, 372, 375, 382, 390, 390T, 398, 399, 50, 550, 565, 575, 590, 595, 65, 675, 690, 698, 698T, 699, 85, 88, Super 90, TE20, TEA20, TED20, TEF20, TO20 Replaces OEM number 181247M1. (Item #: 173021, Ref: 181247M1) $13.10

Differential Ring and Pinion Set - 9-7/8 inch Pinion Gear length. Differential, ring gear and pinion set. 37 and 6 tooth. For tractor models 30, FE35, TO35, 35, 35UK, 50, 135, 135UK, 230, 231, 235, 240, 245, 20, 20C, 20D, 2135, (3165 light duty) check pinion length. Replaces 1683757M91, 182115M91, 1885317M91, 1885317M92. (Item #: 116129, Ref: 531862M91) $306.00

Differential Ring and Pinion Set - 10 inch Pinion Gear length. For tractor models TO35, 130, 135, 150, 230, 235, 35, 40, 50. Replaces 1885317M92 and 1889777M92. Long pinion ( 9.93 inch /252mm), 37 tooth ring gear, 6 tooth 10 spline pinion shaft. (Item #: 187024, Ref: 1683757M91) $345.00

Drive Shaft Retainer Assembly O-Ring - This Drive Shaft Retainer Assembly O-Ring is used on multiple models of Massey Ferguson. Replaces OEM numbers 886089, 886089M1 (Item #: 152375, Ref: 886089M1) $1.30

Drive Shaft, Reverse Gear - 6.580 inches in length, 1.00 inch in diameter. For the following tractors: 1080, 1085, 135, 150, 165, 175, 180, 20, 202, 203, 204, 205, 2135, 2200, 230, 231, 235, 240, 245, 250, 253, 255, 265, 270, 275, 282, 283, 290, 298, 30, 31, 35, 360, 375, 383, 390, 390T, 393, 398, 399, 40, 50, 65, 670, 690, 698, 699, F40, FE35, MH50, TO35. (Item #: 170391, Ref: 180445M1) $20.87

Gasket, Rear Axle Trumpet Housing - Size is approximately 15-1/4 inches. Fits TEA20, TO20, TO30, TO35, 135, 150, 165, 175, 180, 20, 20C, 20D, 2135, 2200, 230, 231, 235, 240, 240P, 245, 2500, 30, 31, 3165, 35, 40, 50, 50, 65. (Item #: 151916, Ref: 183254M1) $4.20

Gear, 1st - This gear is 1st gear for 8 speed transmission. Replaces 520700M1, 183042M1. Gear has 44 teeth and is a 18 spline. For tractor models FE35, 1080, 1085, 135, 150, 165, 175, 180, 20, 20C, 20D, 203, 2135, 2200, 230, 235, 240, 245, 250, 253, 255, 265, 270, 275, 283, 285, 290, 298, 30, 30B, 30D, 31, 3165, 360, 362, 375, 383, 390, 390T, 40, 40B, 50, 50C, 50D, 50E, 65, (20F, 40E, 50H ALL UK MODELS), 35 GAS/DIESEL, 282 MEX. (Item #: 151828, Ref: 1682688M1) $77.00

Gear, 2nd - This gear is 2nd speed for 8 speed transmission. Gear has 23 teeth. For tractor models FE135, FE35, F40, MH50, TO35, 1080, 1085, 11, 165, 148, 150, 155, 158, 165, 168, 175, 178, 185, 188, 20, 20C, 20D, 20F, 202, 204, 205, 2135, 2200, 230, 231, 235, 240, 240P, 245, 250, 253, 255, 262, 265, 270, 275, 282, 283, 285, 290, 298, 30, 304, 31, 3165, 35, 360, 375, 383, 390, 390T, 40, 40B, 40E, 50, 50C, 50D, 50E, 550, 565, 575, 590, 65, 765. (Item #: 173295, Ref: 180419M1) $26.10

Gear, 3rd - This gear is 3rd speed for, 8 speed transmission. Gear has 33 teeth, 17 spline and is 5.075 inches in diameter. For tractor models FE35, MH50, TO35, 1080, 1085, 135, 148, 150, 155, 158, 165, 168, 175, 178, 180, 185, 188, 20, 20C, 20D, 20E, 202, 203, 204, 205, 2200, 230, 231, 235, 240, 240P, 245, 250, 253, 255, 265, 270, 275, 283, 285, 290, 298, 30, 304, 31, 3165, 35, 360, 362, 375, 383, 390, 390T, 40, 40B, 40E, 50, 50C, 50D, 50E, 50H, 550, 565, 575, 590, 65, 765, FE135 COVENTRY, 2135 TURF UTIL NARROW. (Item #: 151824, Ref: 180415M1) $28.70

Gear Lever Tension Spring - This Gear Lever Tension Spring is widely used on many Massey Ferguson Tractors. Confirm part number before ordering. Replaces 192007M1, 964894M1, 180582M1 (Item #: 126830, Ref: 180582M1) $1.98

Gear, Reverse - For tractor models FE35, 1080, 1085, 135, 148, 150, 155, 158, 165, 168, 175, 178, 180, 185, 188, 20, 20C, 20D, 20F, 202, 203, 204, 205, 2200, 230, 231, 235, 240, 240P, 245, 250, 253, 255, 265, 270, 275, 282, 283, 285, 290, 298, 30, 304, 31, 3165, 35, 360, 362, 365, 375, 383, 390, 390T, 40, 40B, 40E, 50, 50C, 50D, 50E, 50H, 550, 565, 575, 65, 765, FE135 COVENTRY, TO35 serial number 17159>, 2135 TURF UTILITY NARROW. This gear is for a 8 speed transmission with 13 and 21 teeth. (Item #: 151823, Ref: 183040M1) $74.00

Gear Shift Boot - Inside diameter top = 5/8 inch, inside diameter bottom = 1-11/16 inch, height 4-3/8 inch. For tractor models 35, 50, 65, 135, 150, 165, 175, 240, 250, 253, 255, 265, 270, 275, (283 8/1993 and up), 290, 360, 362, 375, 383, 390, 390T, 393, 396, 398, 399, 670, 690, 698. Replaces 1694127M1, 1694127M3, 1694127M4. (Item #: 151854, Ref: 1694127M1) $6.10

Gear Shift Boot - For tractor models TE20, TO20, TO30, TO35, 20, 35, 50, 65, 85, 88, Super 90, 135, 150, 165, 175, 230, 235, 245, 255, 265, 275, 285. Top Hole 1/2 inch. Bottom hole 1 1/2 inch. Replaces 180579M4, 180579M3, 108579M3, 520858M1, 237461 (Item #: 114031, Ref: 520858M1) $3.10

No
Picture
Gear Shift Knob - Round ball, 3/8 inch NF thread. For tractor models TO20, TE20, TEA20, TEF20, TO30, TO35, FE35, F40, 130, 135, 150, 165, 175, 20, 202, 203, 204, 205, 2135, 220, 2200, 2500, 30, 302, 303, 304, 30E, 3165, 320, 333, 35, 356, 40, 404, 406, 44, 444, 50, 50A, 50E, 555, 65, 85, 88, 90, Super 90, 95, 98, F40, FE135, MH50, TO35. (Item #: 150683, Ref: 180006M91) $4.00

Gear Shift Spring Retainer - This Gear Shift Spring Retainer is used on many Massey Ferguson Models. Replaces OEM numbers 180583M1, 1861024M1 (Item #: 126687, Ref: 1861024M1) $13.30

Input Housing Gasket - This Gasket replaces part numbers: 188807M2, 512787M2 (Item #: 167235, Ref: 512787M2) $1.90

Input Housing Shaft Seal - 1-1/8 inch inside diameter x 2-1/4 inch outside diameter. For tractor models (TO35, FE35 with single clutch), 135, 135 UK, 2135, 240, 3165, 65, MF35, MF50. (Item #: 178027, Ref: 195523M1) $5.60

Input Shaft Abutment - This part sits between 195513M1 Needle Bearing and 886352M1 Spring. Replaces Massey Ferguson part number ``886353M1 (Item #: 179716, Ref: 886353M1) $12.40

Input Shaft Housing Gasket - For tractor models F40, FE35, TO35, 135, 135 UK, 2135, 240, 3165, 65, MF35, MF50, MH50. (Item #: 166860, Ref: 180434M1) $1.40

Layshaft Housing Gasket - This Layshaft Housing Gasket, also known as Bearing Housing Cap Gasket, is used on some 6 speed, Multi-power and 12 speed Syncromesh transmissions. It replaces OEM part numbers 1004633M1, 181237M1 (Item #: 169496, Ref: 181237M1) $1.50

Lock Nut, Pinion - Used on Massey Ferguson 133, 135, 140, 148, 165, 175, 178, 180, 20, 20C, 2135, 2200, 230, 235, 245, 2500, 255, 265, 275, 30, 31, 3165, 35, 35UK, 40, 4500, 50, 50A, 65, 6500. (Item #: 179636, Ref: 180456M1) $28.90

Main Drive Pinion Shaft Seal - Measures 1.125 inch x 1.562 inch x .250 inch. For tractor models 20, 20C, 202, 203, 2135, 30, 31, 3165, TO35, 135, 150, 165, 175, 230, 235, 245, 35, 50, 65. Replaces: 195501M1, 195870M1. (Item #: 165141, Ref: 195501M1) $4.94

Mainshaft - 11.360 inches long. For tractor models (135, 150, 165, 202, 203, 2135, 3165 all with 6 speed transmission and narrow 1.560 inch planetary gear), (202 early production with standard transmission), (203 serial number up to 659001340 with standard transmission), (35 serial number CN13556 and up with standard transmission), (50, 65 all serial number CN13566 and up with regular transmission), (FE35 serial number 213314 and up with regular transmission). (Item #: 172289, Ref: 187168M1) $155.00

Mainshaft - 12.00 inches long. 4 Groove. For tractor models (150 early models with multipower transmission), (135 serial number up to 9A11664 with multipower transmission), (FE35, 50, 65 all with multipower transmission), (165 with multipower transmission and serial number prefix C). Replaces OEM part number 189440M1, 189441M1, M05-12-07. (Item #: 178378, Ref: 189440M1) $188.00

MAIN Shaft Bearing - Bearing, ball, for MAIN shaft (1 37/64 inch). For all single and dual clutch, 6-speed and multi-power models. Tractors: TO35, MF35, MH50, MF65, MF135, MF150, MF165. (Item #: 169639, Ref: 195502M2) $9.60

Main Shaft Gear - Transmission Mainshaft Gear. Intermediate and high for regular transmission with serial number to 213313. 36/46 tooth, 18 spline. For the following tractors: 35, 50, 65, FE35, TO35. (Item #: 179610, Ref: 180416M1) $159.00

Multi Power Input Housing - This Multi Power Input Housing is used on 135, 150, 165, 175, 180, 1080, 1085, 235, 245, 255, 265, 270, 275, 285, 290, 298, 298, 670, 690, 698, 30, 65, 35, 50. Replaces 1860889M1 (Item #: 110786, Ref: 1860889M1) $167.00

Massey Ferguson 35 Multipower Transmission and Related Parts

Multipower Transmission and Related Parts - Click on picture to view parts. ONLY parts that have a corresponding number are available. Some parts work only with specific serial number ranges within a particular tractor model. Not all parts work with this tractor model. Call for application and availability.

NOTE

Needle Bearing - Measures 1 1/4 inch inside diameter, 1-5/8 outside diameter, 3/4 inch wide. Replaces 1677724M1, 196076M1, 832775M (Item #: 180488, Ref: 196076M1) $22.20

Oil Trough Assembly, LH - For tractor models F40, FE135, FE35, 50, TO35, 150, 20, 202, 204, 20C, 20D, 2035, 2200, 230, 231, 235, 240, 240P, 245, 30, 3165, 35, 50. Replaces 4246537M1, 825774M2, 825774M2 (Item #: 173161, Ref: 825774M2) $45.40

Oil Trough Assembly, RH - Used with differential lock. For tractor models FE135, 135, 150, 20, 20C, 20D, 202, 204, 2135, 2200, 231, 235, 240, 240P, 245, 30, 3165, 35, 50. (Item #: 173346, Ref: 191138M91) $9.50

Pinion Nut Washer - Used on Massey Ferguson models: 133, 135, 140, 145, 148, 152, 155, 158, 165, 168, 175, 178, 180, 185, 188, 20, 20C, 2135, 2200, 230, 235, 245, 2500, 255, 265, 275, 30, 31, 3165, 35, FE35, 40, 4500, 50, 50A, 65, 6500, 765, 865 (Item #: 183834, Ref: 180455M1) $2.51

Planetary Cover Plate, Front - For the following tractors: 1080, 1085, 135, 150, 165, 175, 180, 20, 202, 203, 204, 205, 2135, 2200, 230, 231, 235, 240, 240P, 245, 250, 253, 255, 265, 270, 275, 282, 283, 285, 290, 298, 30, 302, 304, 30B, 30D, 30E, 31, 35, 360, 362, 375, 383, 390, 390T, 393, 40, 50, F40, FE135 COVENTRY, FE35, MH50, TO35, Industrial: 20C, 20D, 20F, 2500, 3165, 40B, 40E, 4500, 50A, 50D, 50E, 60H, 60, 6500. Replaces 180408M2, 180408M1. (Item #: 173500, Ref: 180408M2) $18.30

Planetary Cover Plate, Rear - For the following tractors: 1080, 1085, 135, 150, 165, 175, 180, 20, 202, 203, 204, 205, 2135, 2200, 230, 231, 235, 240, 240P, 245, 250, 253, 255, 265, 270, 275, 282, 283, 285, 290, 298, 30, 302, 304, 30B, 30D, 30E, 31, 35, 360, 362, 375, 383, 390, 390T, 393, 40, 50, F40, FE135 COVENTRY, FE35, MH50, TO35, Industrial: 20C, 20D, 20F, 2500, 3165, 40B, 40E, 4500, 50A, 50D, 50E, 60H, 60, 6500. (Item #: 180666, Ref: 184012M4) $21.30

Planetary Gear Shift Lever - For Super 90, 35, 50, 65, 85, 88. Planetary Gear Shift Lever - Dual Range. Replaces 180440M2 (Item #: 165787, Ref: 185804M1) $16.30

Planetary Selector Gearshift - For tractor models: 1080, 1085, 135, 150, 165, 175, 180, 20, 202, 203, 204, 205, 2135, 2200, 230, 231, 235, 240, 240P, 245, 250, 253, 255, 265, 270, 275, 282, 283, 285, 290, 298, 30, 302, 304, 30B, 30D, 30E, 31, 35, 360, 362, 375, 383, 390, 390T, 393, 40, 50, F40, FE135 COVENTRY, FE35, MH50, TO35, Industrial: 20C, 20D, 20F, 2500, 3165, 40B, 40E, 4500, 50A, 50D, 50E, 60H, 60, 6500. (Item #: 173169, Ref: 180446M1) $17.30

Planetary Thrust Washer - This Planetary Thrust Washer is for tractor models 135, 150, 165, 202, 203, 204, 205, 2135, 302, 304, 3165, 35, 356, 50, 65, 85, 88, Super 90, F40, FE35, TO35. (Item #: 172988, Ref: 180414M1) $16.20

Power Input Shaft - Power Input Shaft with 6 speed transmission has 18 tooth, 10 spline, length of 14 inches. For tractor models 135, 150, 20, 202, 204, 20C, 2135, 2200, 230, 235, 245, 285, 35, 50, F40, FE135, FE35, TO35. Replaces 1669325M1, 180420M1. (Item #: 166908, Ref: 1669325M1) $128.00

No
Picture
PTO Lift Pivot Shaft - For Massey Ferguson tractor models F40, TO35, 35, 35 (France), 35X (France), 50, 50 (Harris and Massey), 65, 135, 135 (UK), 150, 165, 165 (UK), 175, 175 (UK), 178 (UK), 180, 230, 231, 231S, 235, 240, 240 (S, Turkey), 245, 250, 255, 265, 265S (Turkey), 270, 271X, 271XE, 275, 275 (UK), 281, 281X, 281XE, 282, 283, 283 (UK), 283 (Brazil), 285, 285S (Turkey), 290, 290 (UK), 298, 360, 375, 383, 390, 390T, 393, 396, 398, 399, 431, 451, 461, 471, 481, 492, 543, 583, 596, 670, 690, 698, 699, 1080, 1085, 4225, 4233, 4235, 4240, 4243, 4245, 4253, 4255, 4260, 4263, 4265, 4270, 4325, 4335, 4345, 4355, 4360, 4370, 8250, Compatible with Massey Ferguson Construction and industrial models 20, 20C, 20D, 20E, 20F, 30, 30B, 30D, 30E, 31, 40, 40B, 40E, 50C, 50D, 50E, 202, 203, 204, 205, 302, 304, 2135, 2200, 3165, Replaces Massey Ferguson OEM number 898304M91, (Item #: 176229) $7.70

Rear Axle Oil Seal, Outer - This rear axle oil seal is for tractors with brake drums. Measures 2 3/4 inches inside diameter, 3 5/8 inches outside diameter and 19/32 inches wide. For tractor models TO35, 135, 230, 235, 240, 35, 50. (Item #: 108416, Ref: 195677M1) $7.00

Rear Drive Shaft Needle Bearing - Used on Massey Ferguson models: 1080, 1085, 133, 135, 140, 148, 150, 152, 158, 165, 168, 175, 178, 180, 185, 188, 20, 202, 204, 20C, 20D, 20E, 20F, 2135, 230, 231, 235, 240, 245, 250, 253, 255, 265, 270, 275, 282, 283, 283 Brazilian, 285, 290, 298, 30, 30B, 30D, 30E, 30H, 31, 3165, 340, 342, 35, 350, 352, 355, 360, 362, 365, 372, 375, 375E Brazilian, 382, 383, 390, 390E Brazilian, 390T, 393, 396, 398, 399, 40, 40B, 40E, 50, 50A, 50B, 50C, 50D, 50E, 50EX, 50F, 50H, 50HX, 550, 565, 575, 590, 595, 60H, 60HX, 65, 670, 675, 690, 698, 698T, 699. This bearing replaces OEM numbers 195513M1, B1212, S1212 (Item #: 179695, Ref: 195513M1) $22.00

Sealing Ring - This sealing ring is 1-1/2 inch outside diameter and 3/32 inches wide. Two used per input shaft. Replaces Massey Ferguson part number 186581M1. (Item #: 165436) $6.40

Seal, PTO Pinion Shaft Retainer - This PTO Pinion Shaft Retainer Seal measures 1 15/16 inches outside diameter, 1 5/8 inches inside diameter and 1/4 inch wide. Multi-Power Transmission. Replaces 1860867M4, 1860867M5, 1860867M1, 1860867M3 (Item #: 128472, Ref: 1860867M3) $5.50

Seal, Rear Axle Oil, Inner - This oil seal fits: [Industrial; as an inner rear axle shaft oil seal with dry brakes: 2135, 2200, 3165, MF20, MF20C, MF30 (2 used per tractor, sold individually)], as a transmission input shaft front cover oil seal: 85, 88, Super 90, [as an inner rear axle shaft oil seal with dry brakes: 135, 150, 202, 203, 204, 205, 230, 231, 235, 240, 245, 35, 50, F40, FE35, TO35 (2 used per tractor, sold individually)]; Replaces: 195678M1, 195678M2. 2.125 inches inside diameter, 2.879 inches outside diameter, 0.438 inches wide. (Item #: 108415, Ref: 195678M2) $6.20

Shift Fork, 1st, Reverse, 2nd and 3rd - For tractor models FE35, F40, MH50, TO35, 1080, 1085, 135, 150, 165, 175, 180, 20, 20C, 20D, 202, 203, 204, 205, 2135, 2200, 230, 235, 245, 255, 265, 270, 275, 285, 290, 298, 30, 31, 3165, 35, 50, 65. (Item #: 151023, Ref: 180437M1) $34.40

Shift Lever Locking Pin - This Shift Lever Locking Pin is used on Ferguson, Massey Harris and Massey Ferguson applications. It replaces OEM part numbers 180581M2, 1678440M1, 180581M1 (Item #: 183009, Ref: 1678440M1) $1.40

Shift Rail, 1st and Reverse - Replaces: 180442M2. For the following tractors:1080, 1085, 135, 150, 165, 175, 180, 20, 202, 203, 204, 205, 2135, 220, 2200, 230, 231, 235240, 245, 250, 253, 255, 265, 270, 275, 282, 283, 285, 290, 298, 30, 302, 304, 31, 35, 40, 50, 65, F40, FE135, MH50, TO35 (Item #: 172890, Ref: 1678867M1) $48.11

Shift Rail, 2nd and 4th - Shift Rail, 2nd and 4th. Replaces 180438M2 For the following tractors: 135, 138, 148, 155, 158, 165, 168, 175, 178, 185, 188, 230, 240, 250, 265, 275, 285 with 11x38 differential, 290, 340, 35, 350, 355, 360, 362, 365, 375, 390, 390T, 398, 399, 550, 565, 575 with 11x38 differential, 590 with 11x38 differential, 65, 675, 690 with 11x38 differential, 765, FE35. (Item #: 172896, Ref: 1678866M1) $39.90

Side Cover Gasket - This Side Cover Gasket fits the multiple Ferguson and Massey Ferguson tractor models as a side cover gasket and a PTO shift cover gasket. It replaces original part numbers 181217M3, 181217M1, 181217M2, 181217M4, 181217M5, 181217M6, 3816331M92, 181217V3, 3816331T92. (Item #: 112236, Ref: 9N4131) $1.00

Snap Ring - Internal - For Massey Ferguson tractor models TO35, 20, 30, 31, 35, 50, 135, 150, 165, 175, 178, 230, 235, 240, 245, 2135, 3165, Compatible with Massey Ferguson Construction and industrial models 20C, 30, 31, 40, 50, 50B, 65, Replaces Massey Ferguson OEM number 195222M1, (Item #: 169491) $0.98

Transmission Countershaft - 17/20 spline, 15 tooth, 12.250 inches long. For tractor models (35 Gov, Util, Turf, Standard with Manual shuttle), (135, 150 6/8 speed transmission serial number up to CB22864/ multi power), (165 8 speed transmission serial number up to CB22864/ 6 speed multi power). Replaces 195453V1, 906472M2, 906743M92, M05-08-02. (Item #: 165986, Ref: 906743M92) $27.60

Transmission Fill Plug - For tractor models TE20, TEA20, TO20, TO30, 35, 40, 50, 135, 231, 240, 250 2135. Replaces 768300M1, 180580M1 and 3799441M2. Plug has a 2.3 inch outside diameter flange. (Item #: 115163, Ref: 9N7010) $6.30

Transmission Mainshaft - For Regular Transmission with serial number to 213313. Shaft is 11.375 inches long, 18 spline. For the following tractors: 35, 50, 65, FE35, TO35. (Item #: 173091, Ref: 180441M1) $88.98

Transmission Rear Axle Gasket - This gasket is used on multiple Massey Ferguson tractors. Dimensions measure 10.750 inches X 16 inches. It replaces original part numbers 1861986M1, 1861986M2, 3599804M1, 3599804M2, 3599804V2, 8884457M1, 181363M1, 521181M1, VPH1405 (Item #: 111906, Ref: 1861986M1) $6.90

Transmission to Differential Shaft Spring - Used with 886353M1 abutment and 195513M1 this spring sits inside the differential input shaft. (Item #: 179661, Ref: 886352M1) $10.10

Electrical System

Alternator with Tach Drive - This is a 12 volt 63 amp alternator. It is internally regulated and comes with fan and pulley. This alternator can be used to replace original generator. Additional brackets and hardware may be needed. Tach drive is appropriate for gas tractors where the tach drive is on the generator. Use part number ADR9209 to make this a single wire self exciting alternator (not included). (Item #: 164228, Ref: ADR0382) $150.00

Battery Cable - Cable, battery to solenoid. For tractor: TO35 battery to ground for tractors: MF35 gas, MF85D, MF88D, MF Super 90 gas. 14-1/2 inches long. For TO20, TO30. (Item #: 115760, Ref: 181572M91) $17.50

Battery Cable - Cable, battery to solenoid, 24 inches. For 202, 204, 35, 65, F40, Super 90. (Item #: 172373, Ref: 186827M1) $19.80

Coil, 12V - This 12 Volt Coil with internal resistor comes with bracket for Delco distributor with screw held cap. For tractor models 202, 204, 302, 304, 356, MF1100, MF135, MF150, MF165, MF175, MF180, MF35, MF50. (Item #: 105299, Ref: 189673M1) $18.50

Coil, 12 Volt - This 12 Volt Coil has an internal resistor for tractor models Super 90, Super 95, TO35, 150, 165, 180, 202, 35, 410, 50, 65, 85, 88. (Item #: 105299, Ref: 189673M1) $18.50

Coil, Ignition 6V - Coil for Delco Distributor with clip held cap. For 202, 204, 20, 26, 27L, 27, 302, 303, 304, 34, 356, 35, 402, 404, 60, 70, 72, 80, 82, 90, 92, MF35, MF50, MF65, MF85, MF88, MH50, Super 92, Super 90, TO20, TO30, TO35. Replaces 1024481M91. (Item #: 105281, Ref: D4PE12029AA) $15.00

Distributor - A complete distributor that comes with cap, points, rotor and condenser. It has a 9 tooth shaft gear. For tractor models TO20, TE20 with Continental Engine, TO30, TO35, 35 (to serial number 245932), F40, 50 to serial number 536248. (Serviceable for: 135, 202, 204, 2135, 2200 (early with 1112643 distributor and Z134 engine). Replaces 1111722, 1111740, 1112557, 1112570, 1112586, 181544M91, 181685M91, 181686M91, 182852M91, 829856M9. (Item #: 152856, Ref: 182852M91-TP) $135.65

Distributor Cap - Distributor cap for 4 cylinder models using a Delco distributor with a clip held cap. For models TO20, TO30, TO35, 35, 202, 204, 302, 304, 50, 65, 85, 88, Super 90. Replaces 811735 Delco and 1750411M1. (Item #: 104554, Ref: 1750411M91) $8.70

Distributor Cap 4 Cylinder - For tractor models 35, 50, 65, 135, 150, 165, 175, 180, 1100, MH50, IND 202, 204, 302, 304, 356. This is a Delco style screw on cap. (Item #: 105569, Ref: 1024914M91) $10.80

Distributor Cap 6 Cylinder - Distributor CAP For 202, 204, 302, 304, 34, 35, 356, 92, MF35, MF50, MF65, MF85, MF88, MH50, Super 92, Super 90. For Delco. Replaces 1509692M1 812627, 824735, 825409, 1867722, 1889361, 1911597, 12338674, D301, D301A, D320. (Item #: 104557, Ref: 21A443) $12.00

Distributor Cap 6 Cylinder - Distributor CAP For 202, 204, 302, 304, 356, MF1100, MF135, MF150, MF165, MF175, MF180, MF35, MF50 (Item #: 105585, Ref: 1960810) $12.70

Distributor Dust Cap - Used on Delco distributors with Screw Held caps, this dust cover replaces OEM numbers 1024915M1, 156359A, 1960325, 702539, 74056699, R11264. 3.300 inches outside diameter, 1.047 inches tall, 0.210 inch screw holes. (Item #: 125927, Ref: 1960325) $17.00

Distributor Dust Cover - Dust Cover for Delco Distributor with Clip Held Cap. For 202, 204, 302, 304, 34, 35, 356, 92, MF35, MF50, MF65, MF85, MF88, Super 92, Super 90, TO20, TO30, TO35. Replaces 1750491M91. (Item #: 103153, Ref: 1900119) $9.00

Distributor Shaft Bushing and Shim Kit - Delco Distributor Shaft Bushing and Shim Kit. fits tractor models F40, 202, 204, 40, Super 90, 85, 88, TO20, TO30, TO35, 302, 304, 35, 50, 65, 95, 97 with one of the following Delco distributors: 1112557, 1112570, 1112585, 1111722, 1111737, 1111740, 1112583, 1112589. Replaces: washer: 1750412M1, bushing: 1750499M1, shim washer: 1750406M1, 1025008M1 (Item #: 178103, Ref: ABC3007) $29.50

Distributor Terminal Insulator Assembly, Delco - This Delco Distributor Terminal Insulator Assembly is for Round Shoulder (outside terminal). Note: As distributors can be changed over time, it is best to double check which style you require. This is only a guide of what was original. Fits distributor housings with 0.345 inch diameter round hole. If not sure, measure before ordering. Originally used on 35 Combines and TO20 Tractors. Replaces: 1750438M1, 1750455ML, 22303X, 353444XL, 357119 (Item #: 111459, Ref: 1878405ASSY) $15.00

Distributor Terminal Insulator Assembly, Delco - This Delco Distributor Terminal Insulator Assembly is for Square Shoulder (outside terminal). Note: As distributors can be changed over time, it is best to double check which style you require. This is only a guide of what was original. Fits distributor housings with 0.300 Inch diameter round hole with a keyway. If not sure, measure before ordering. Fits Massey Harris 92 Combine, Massey Harris 50. Ferguson F40, TO30, TO35, 202, 204, 302, 304, 356, 50, 65, 85, 88, 95, 97, Super 90, 35. Replaces: 1750513M1, 1750514M1, 1750520M1, 22303X, 353444XL, 354119X (Item #: 111468, Ref: 1904376) $14.40

Electronic Ignition Conversion Kit -12V Negative Ground - For 35, F40, 50 all with Cont Z134 engine and Delco (D)1112643 dist, MF65 with Cont G176 engine and D1112644 dist, 135 Spec with Cont Z145 with D1112643 dist, 135/150 with Cont Z145 and D1112644 dist, 165 with Cont G176 engine and D1112644 dist, 165 with Perkins AG4-212 with D1112458 dist, 175/180 with Cont G206 engine with D1112647 dist, 175/180/185 with Perkins AG4-236 engine with D1112693 dist, MF255 with Perkins AG4-212 engine and D1112458 dist, MF265/MF285 with Perkins AF4-236 engine and D112693 dist. Also works with H-260 Continental Engine.Electronic ignition conversion kit. Replaces points and condenser with an electronic module. For use on 12 volt neg grnd system only. Never change points again. Easy to install. Increase spark plug life and horsepower. Improve fuel economy. (Item #: 105073, Ref: 1145A) $123.00

Electronic Ignition Conversion Kit, 12 volt negative ground - Fits TO20, TO30, TO35, 50, MH50, 65 : - For TO20 with Continental Z120 engine and Delco distributor. TO30 with Continental Z129 engine and Delco 1111740 distributor, TO35 and MH50 with Continental. Z129 or Z134with Delco distibutor 1112557 or 1112570, TO35, 35 and 50 with Continental Z134 and a Delco 1112570, 1112585 or 1112385 distibutor, 65 with Continental G176 engine and a Delco 1112583 or 1112589 distributor. Also fits aftermarket ATL-55-1200. Electronic ignition conversion kit. Replaces points and condenser with an electronic module. For counter clockwise distributors with clip type cap. For use on 12 volt negative ground system only. Never change points again. Easy to install. Increases spark plug life. Increases horsepower. Improves fuel economy. Solid-state electronics. (Item #: 113775, Ref: 1143) $154.00

Electronic Ignition Conversion Kit, 6 volt positive ground - For TO20 with Continental Z120 engine and Delco distributor including Delco distributor 1112618. TO30 with Continental Z129 engine and Delco 1111740 distributor, TO35 and MH50, 50 with Continental. Z129 or Z134with Delco distibutor 1112557, 1111722 or 1112570, TO35, 35 and 50 with Continental Z134 and a Delco 1112570, 1112585 or 1112385 distibutor, 65 with Continental G176 engine and a Delco 1112583 or 1112589 distributor. Also fits aftermarket ATL-55-1200. Electronic ignition conversion kit. Replaces points and condenser with an electronic module. For counter clockwise distributors with clip type cap. For use on 6 volt positive ground system only. Never change points again. Easy to install. Increases spark plug life. Increases horsepower. Improves fuel economy. Solid-state electronics. (Item #: 113774, Ref: 1143P6) $170.00

Electronic Ignition Conversion Kit, High Perfomance, 12 Volt Negative Ground - The Ignitor II has many of the same great features that the Ignitor has, but its smarter. It senses the coil current level and use a powerful micro controller to adjust variable dwell which helps to maintain peak energy throughout the entire RPM range. Senses startup and develops more energy for quicker, easier starting. Current protection shuts down the system, preventing component damage. NOTE: Ignitor II applications can not be used with solid core ignition wires, can be used with our ignition wires p/n CPN12259EI. Replaces points and condenser with an electronic module. Use with 12 volt negative ground systems. For tractor models 35, F40, 50 all with Cont Z134 engine and Delco (D)1112643 dist, MF65 with Cont G176 engine and D1112644 dist, 135 Spec with Cont Z145 with D1112643 dist, 135/150 with Cont Z145 and D1112644 dist. (Item #: 183757, Ref: 91145A) $186.00

Fuse Holder - Mounts in 5/8 inch diameter hole. 2 spade connectors. Replaces: 186216M91, 186216M91, 506063M91, 522462M91 (Item #: 112273, Ref: 376852R91) $11.10

Generator, 12 Volts - Lucas style replacement, 12 volt, pulley is not included. For tractor models: 135, 148, 155, 158, 165, 168, 175, 178, 185, 188, 35, 35X, 50, 65, FE35, TE20, TEA20, TED20, TEF20. Replaces K908882, 3049871R91, 81806433, ADN10001R, ADN10001, E27N10000, 2871170, 897104M92, 12871182, 37H8231, 22703, 22791, LRD101, 2871170, 2871182, 22703, 22791, LRD101, 897104R92, 897104T, 897104M92, 2871182 (Item #: 113578, Ref: R1192673) $162.00

Ignition Kit, Delco Clip-Held Cap Distributor - Ignition kit For Delco distributor with CLIP held cap. VERIFY DISTRIBUTOR NUMBER TO ENSURE FIT. Contains points, condenser, and rotor. Fits 202, 204, 302, 304, 34, 35, 356, 92, MF35, MF50, MF65, MF85, MF88, Super 92, Super 90, TO20, TO30, TO35, 95, 97, F40, 202, 204, MH50. For Delco distributor numbers 1111716, 1112583, 1112589, 1112557, 1112570, 1112585, 1111722, 1111737, 1112583, 1111740. (Item #: 103151, Ref: ATK1DCR) $9.80

$Massey Ferguson 35 Ignition \ Light Switch$
Ignition / Light Switch - Used on Massey Ferguson 202, 35, 204, 65, Super 90, and 50 tractors, this is a 5 Position Switch. It has 4 Terminals with 2 keys. The post OD is 3/4 inches. Replaces 189527M91, 189527V91, 189527M91. This switch is used on Gas and LP equipped tractors. (Item #: 170613) $81.00

Ignition Tune-Up Kit - For Massey Ferguson tractor models Super 90, TO20, TO30, TO35, 35, 40, 50, 65, 85, 88, 202, 204, Fits models with Continental engines with Delco distributors with clip held cap, (Item #: 168708) $29.00

Neutral Safety Switch - This Neutral Safety Switch has blade type terminals. For tractors: MF240*, MF250*, MF253, MF282, MF283 except Brazil, MF298*, MF360, MF362, MF375, MF383, MF390, MF393, MF398, MF399 industrial: 40E*. *Optional with 3381094M1. Replaces 888501M2, 963417M2, 1012043M91, 1679 223M2, 1679223M1, 1679223M2, 3381094M1, 34198, 39121, 39855, 963417M2, SMB497. (Item #: 164579, Ref: 1679223M2) $26.50

Neutral Safety Switch - This Neutral Safety Switch is for bullet type terminal. Replaces 181140V94, 53208520, 181140M1, 181140M91, 181140M94, 181140M93, 181140M92. (Item #: 111507, Ref: 181140M94) $11.30

Neutral Safety Switch Boot - For tractor models: 35, 40, 50, 65, 85, 175, 180, 230, 235, 245, 255, 265, 275, 285, 20, 20c, 30, 30B, 30D, 31, 40, 40B, 50, 50A, 50C, 50D, 60, 2135, 3165, 22, 2500, 4500, 6500, 88, 135, 150, 165, Super 90, 202, 203, 204, 205, 302, 304. (Item #: 178119, Ref: 180776M1) $12.80

Regulator Control Box - For tractor models 35 with A3.152 Engine, FE35 with 23C or 87MM Engine. Regulator Control Box also replaces numbers 2872625, 2872631. (Item #: 173147, Ref: 826788M1) $63.00

Rotor - Used with Delco distributor and clip held cap. For tractor models (35 up to serial number 245033), (50 up to serial number 536249), (65 up to serial number 702826), TO20, TO30, TO35. (Item #: 110177, Ref: 1750498M1) $3.60

Rotor - Used with Delco distributors1112577, 1112570, 1112585, 1112591, and 1112598 with a clip held cap. For tractor models: 35 (up to serial number 245033), 50 (up to serial number 536249), 65 (up to serial number 702826), 85, 88, Super 90, 97. Replaces 1750498M1 and 1750785M1. (Item #: 110177, Ref: 1750498M1) $3.60

Solenoid, Starter - For Massey Ferguson tractor models TO35, 35, 35 (Turf and Utility), 35 (Government (655 Series)), 50, 65, 85, 88, 205, 300 (S), 302, 304, 350 (SS), Compatible with Massey Ferguson Construction and industrial models 200, 202, Compatible with Massey Ferguson Lawn and Garden (s) 10, 12 Replaces Massey Ferguson OEM number 182696M91, 182696M1, , Compatible with Massey Harris tractor models 50, Fender or firewall mount, Fits Massey Ferguson tractor models 205-4, 400SST, 500SST, 500 Special, Super 90, Fits Massey Ferguson Lawn and Garden (s) 7, 8, 8E, 14, , (Item #: 168108) $36.80

Solenoid Switch - Solenoid Switch, 12-volt. Three Post. Can be used as a saddle mount or flat surface mount. May come in a metal or plastic casing. For tractors: TO35, F40, MF35, MF50, MF65, MF85, MF90 Industrials: 202, 204, 302, 304, 256 utility gas and LP models. Replaces 182696M91, 182696M1. May come in a silver metal casing versus black plastic. (Item #: 150223, Ref: DR1467) $18.70

Spark Plug Wire Set, Custom - No cutting or fitting required for these wires. These are custom made for the following 4-cylinder Continental Gas engines using Delco Distributors: Z120, Z129, Z134, and Z145. Used on tractors: TE20, TO20, TO30, F40, 135, 135 Deluxe, 150, 35, 50, MH50, TO35. Also used on INDUSTRIALS: 202, 204. (Item #: 113765, Ref: S.42779) $17.00

Starter - This is a new Delco Style Starter. 10 teeth, clockwise rotation, 12 Volt. For tractor models 135, 150, 165, 235, 30, 302, 304, 3165, 35, 356, 40, 65. All with diesel engines. Replace 535388M92, TS-1036, 1107503, 1107512, 1107860, 1107870, 191081M92, 191081M93, 515913M91, 515913M92, 579934M91, 579935M91, 72072956, 773363M91, AM1107860, S14192, 1108662, 1109264, 1200-0113, 1200-3119, 12301330, 1403617M91, 189117M91, 1900434M91, 1903617M91, 191091M92, 1998345, 1998377, 2072956, 323-673, 323-700, 323673, 323700, 515913M93 (Item #: 168794, Ref: 515913M91) $310.00

Starter - This Lucas style starter is for 12 volt, 10 tooth, clockwise rotation. 3-bolt mount, Diesel engines. For tractor models (205, 250SP 1966 to 1972 with Chrysler H-170), (FE65 1956 to 1962 diesel), (20, 40 1970 to 1971), (35 1960 to 1968), (65 1959 to 1964), (135 1964 to 1973 with Perkins 152 diesel), (148 1964 to 1972 with Perkins 152 diesel), (154 1986 to 1989), (154 1980 to 1981 with Perkins 152 diesel), (165 1964 to 1969 with Perkins 203 diesel), (184 1980 to 1985 with Perkins 236 diesel), (263T from 1993 up), (364 1989 to 1993 with Perkins 152 diesel), (2135 1964 to 1968), (702 1959 to 1962). Replaces; Delco: 1107870, 1107512, 12301330, 1107853, 1107860, Dixie: TS-1036, 260-62143, Massey Ferguson: 191091M92, 515913M93, 579934M91, 513913M92, 1900434M91, 191081M93, 1403617M91, 515913M92, 189117M91, 1903617M91, 513913M91 1107503. (Item #: 111745, Ref: SLU0008) $220.00

Starter - This is an Off Set Gear Reduction replacement for 515913M91. It is used on 135, 150, 165, 235, 30, 302, 304, 3165, 35, 356, 40. All with diesel engines. Replace 535388M92, TS-1036, 1107503, 1107512, 1107860, 1107870, 191081M92, 191081M93, 515913M91, 515913M92, 579934M91, 579935M91, 72072956, 773363M91, AM1107860, S14192, 1108662, 1109264, 1200-0113, 1200-3119, 12301330, 1403617M91, 189117M91, 1900434M91, 1903617M91, 191091M92, 1998345, 1998377, 2072956, 323-673, 323-700, 323673, 323700, 515913M93, 1868283M5 (Item #: 181965) $147.00

Starter, 12 Volt - For tractor models 135UK, 35, TEA20, TED20 with Standard Gas Engines (not Continental). Also replaces 25038, 1903125M91, S2532, 25038D. 12 volt system. (Item #: 115902, Ref: 829803M91) $524.90

Starter, 12 Volt - This new 12 volt starter with drive is for tractor models TO20, TO30, 35, 50, 65, 202, 204, 302, 356, TO35. Verify number off old starter. Overall length is 12.5 inches (PLEASE VERIFY OVERALL LENGTH OF YOUR OLD STARTER. THIS MAY NOT FIT YOUR TRACTOR IF YOUR OLD STARTER IS SHORTER THAN 12.5 InchES), Diameter is 4 inches, 2 bolt center-to-center is 4.25 inches. Replaces the Delco number 1107226 and the original equipment numbers: 181541M91, 1109457, 182454M92, 1107654, 190004M91, 1107226 and TISCO starters 7877-EX, 81271-EX, 85451-EX, 4858MFGXL_12V, and 1900348M91. (Item #: 160371, Ref: 1107226) $215.00

Starter Assembly - 12 volt, diesel, 10 teeth, 2.7KW. For tractor models MF30, MF50, MF165, MF174, MF174C, MF194, MF265, MF270 MF275, MF285, MF290, 6500, 7500, 8500. Replaces Lucas, 26413, 27411, 27433, 27539, 26410 LRS190R, 26412, 26412R, LRS190, 27432, 26264, 26154, 26264R. 1680065R3, 1680065M3, 1680065M1, 26264R, 26412R, 27432R, 3.93E+07, 26412, 26220, 3597371M2, 3597426M3, 3597426M2, 968856M1, LRS190R, 3930505R1, 1868285M3. Left side mount. (Item #: 157974) $105.98

No
Picture
Starter - Delco Style (4145), Remanufactured, Delco Remy, 1107654, 182454M92 - For Massey Ferguson tractor models TO35, 35, 65, Compatible with Massey Ferguson Construction and industrial models 50, 202, 204, Replaces Massey Ferguson OEM number 182454M92, 1900347M91, 182454M91, Replaces Delco Remy manufacturer number 1107654, Replaces manufacturer number 4145, 140-026, 91-01-4708, Delco Style, Voltage: 12, Rotation: Clockwise, Teeth: 9, (Item #: 203436) $440.01

Starter Drive - Drive assembly. For tractors, except diesel: MF35, MF50, MF65 industrials: 202, 204, 302, 356. Services starter 1107226. For 202, 204, 302, 356, MF35, MF50, MF65 (Item #: 178979, Ref: 1019269M91) $90.00

Starter Drive - Drive assembly. For Continental Z145 in tractors: 135, 150, 165, 175, 178, 180, 20 Indust/Const, 202 Indust/Const, 205, 20C Indust/Const, 2135 Indust/Const, 2200 Forklift, 2200 Gas, 230, 235 Indust/Const, 235 Orchard, 245, 245 Orchard, 2500 Forklift, 302 Indust/Const, 304 Indust/Const, 30B Indust/Const, 3165 Indust/Const, 35, 356 Indust/Const, 40, 4500 Forklift, 50 Indust/Const, 65 . Replaces Delco 1963808. 9 tooth, Clockwise Rotation, for Delco 10MT. Services starter 1108324. (Item #: 124822, Ref: 1025380M91) $29.68

Starter Drive - Drive Assembly attaches with keyway and set screws. For tractors: TO20, TO30, TO35, 50, MH50, 35, 65, F40, 202, 203. Services Delco Starters 1107755, 1107654, 1109457. NOTE: Please check the starter that is in your tractor, some starters use a pin to attach drive not a set screw. (Item #: 113968, Ref: 1035335M91) $33.10

Starter Solenoid - Solenoid Assembly, flange mounting to starter. Replaces Delco 1114356 on starters 1108649, 1107503, 1107512, 1108649. Gas and diesel applications. 12-volt. Replaces 1025381M91, 1047083M91, 1755027M91. (Item #: 105675, Ref: 1047083M91) $17.00

Starter Switch - Switch Assembly with key, for ignition and light. Switch has 3 terminals. For GAS tractors: TE20, TEA20, TO20, TO30, TO35, MF35, MF50, MF65, 202, 203, 204, 205. (Item #: 111516, Ref: 180681M93) $14.00

Starter Switch - For tractor models Super 90, 135, 165, 50, 65), 35 Gas and Perkins Diesel, TO35 Gas and Standard Diesel. Starter Switch. 4 prong. Includes 2 keys. This is a three position switch, heat, operate, start. - LUCAS Equipment. Replaces 35630, 883920M1, 967570M4, 504809M91, 963416M1, 883928M1, 883928M91, 417402M1, 2846124 (Item #: 111515, Ref: 883928M1) $9.40

Switch, Lamp and Horn - Lucas type. Used on 135, 148, 165, 168, 175, 178, 185, 188, 230, 235, 240, 245, 250, 255, 265, 275, 290, 298, 35, 35 Gas / 35 Petrol, 35X, 375E Brazilian, 390E Brazilian, 50, 50E, 50EX, 565, 575, 590, 65, 765. Replaces 882283M1, 54033364, 34952 (Item #: 124742, Ref: 1502378C1) $18.90

Switch, Push Button - This 2 Terminal Switch has many applications. It is a heavy duty momentary switch, push for on and release for off. It is rated for up to 35 volts. Uses two screw terminals. The mounting stem is 5/8 inch number 32 thread. It is 21/32 inch over all length. Check measurements before ordering if using as a universal part. Applications include Ether Switch, Horn Button, Cold Start, Starter Switch and Manifold Heater Switch. Replaces: 189158M1, 189158M91, 767828M91. (Item #: 121141, Ref: R7994) $12.50

Switch, Push Button - Fits multiple Massey Ferguson tractors. Replaces 189158M91, 189158V91, 181141M91. (Item #: 105703, Ref: 189158M91) $11.30

Tune-up Kit, Basic - FOR DELCO DISTRIBUTORS WITH SCREW-HELD CAP. Ignition KIT with ROTOR For 202, 204, 302, 304, 356, MF1100, MF135, MF150, MF165, MF175, MF180, MF35, MF50, MF65. (Item #: 105278, Ref: ATK10DSR) $10.70

Tune-up Kit, Comprehensive - For Delco distributor with clip-held cap. For 4-cylinder gas engine, kit includes: AL 386 spark plugs, plug wires, points, condenser, rotor, distributor cap. Fits tractors: TO20, TO30, TO35, 35 Ag. before serial number 245033, 35 Utility before serial number 655001052, 35 Turf before serial number 65600452, 85, 88, 90 Super, MH and 50 before serial number 536249, 65 before serial number 702825, 202 Ind. Before serial number 308962, 204 Ind. Before serial number 343688, 302 Ind. Before serial number 119750053, 356 Ind. Before serial number 570001025, Swathers 34, 44. Combines 92, Super 92. (Item #: 158888, Ref: MFTUNEKIT) $58.00

Tune-Up Kit, Delco Screw Held Cap - Used on Massey Ferguson 4 cylinder Continental models 35, 50, 135, 150, 202, 204, 2135, 2200, 2500, all with Delco distributors with SCREW held cap. Contains point, rotor, condenser, cap, spark plugs, and spark plug wires. (Item #: 158889) $58.00

Tune-up Kit, With Plugs - This Tune-up Kit is for Clip held Cap Delco Distributors, 4 cylinder gas models and includes Autolite spark plugs (Replaces Autolite AL386, AL388, AL3116 and Champion D10, D14, D16, RD16, D21, D23 plugs), points, condenser, and rotor. For models TO20, TO30, TO35, (MF35 with serial number prior to 245033), (MH50 with serial number Prior to 536249), (MF50 with serial nunber prior to 536249), (MF65 with serial number prior to 702825), MF85, MF88, MF90 Super, (35 Utility with serial number prior to 655001052), (35 Turf with serial number prior to 656000452), (202 with serial number prior to 308962), (204 with serial number prior to 343688), (302 with serial number prior to 119700082), (304 with serial number prior to 119750053), (356 with serial number prior to 570001025), Super 92. Verify correct spark plug size and type (Item #: 173738, Ref: MFITK10) $27.30

Tune-up Kit, With Plugs - This 4 cylinder Tune-up Kit is for Delco Distributors with screw type cap. VERIFY SPARK PLUG SIZE as this kit comes with AL386 that are 18MM, 1/2 inch reach and 7/8 hex size. For tractor models 35, 50, 65, 135, 150, 165, 175, 180, 1100, MH50, 202, 204, 302, 304, 356. Includes plugs, points, condenser and rotor. Verify correct spark plug size and type (Item #: 182530, Ref: MF-ITK-40) $25.90

Voltage Regulator, 12 Volt - 12 Volt - 4 Terminal - Flat Mount. 4 Terminal: Light - Battery - Field - Armature (underneath base). Fits TO35, MF25, F40, MF35, MF50, MF65, MF85, MF88, MF Super 90, MF135, MF150, MF165, MF175, MF180, MF202, MF204, MF203, MF205, MF2135, MF3165. Combines SP300, SP410, SP510. 12 Volt models with generators. The Three Post side of this regulator may be parallel or slightly splayed. (Item #: 105581, Ref: 182548M92) $26.50

Wiring Harness - This Wiring Harness is used on Massey Ferguson Tractor 35 built in the UK with serial number 304623 and later, with Perkins A3.152 Diesel engine and Lucas electrical. It replaces part number 54933558. (Item #: 113570, Ref: 54933558) $64.30

Engine Bearings

No
Picture
Cam Bearing Set - This cam bearing set is for the Z129 and Z134 engines in TO30, TO35, 35, F40, MH50, 50, 135 SPECIAL, INDUSTRIALS 202 and 204. Standard Set. (Item #: 107235, Ref: SH-683S) $66.00

No
Picture
Gasket - Steering Box - For Massey Ferguson tractor models 35, 35X, 135, 148, 230, 231, 240, 250, Compatible with Massey Ferguson Construction and industrial models 20D, 20E, 30E, Replaces Massey Ferguson OEM number 1891676M1, 1850038M1, 1893620M1, (Item #: 168940) $2.30

Main Bearing Set, .010, Perkins 152 Gas or Diesel - .010 inch Main Bearing Kit. For 200B, 200, 203, 205, 20C, 20, 2135, 2200, 2244, 2500, 30B, 35, 40, 4500, FE35, MF135, MF150, MF230, MF235, MF245, MF250, MF35, MF50 with AG3-152 Perkins Gas Engine or A3-152 and AD3-152 Diesel Engines. Thrust washers not included. Complete for 1 engine. Replaces 746157M91 (Item #: 107163, Ref: 746157M91) $15.00

No
Picture
Main Bearing Set, .010, Z134-Z145 Gas - Main bearing set .010 inch for tractors using Continental Z134 or Z145 Gas Engines: 35, 50, 135, 150, 202, 204, F40, MH50, TO35. Complete for 1 engine. (Item #: 107158, Ref: 837156M91) $125.00

No
Picture
Main Bearing Set, .020, Perkins 152 Gas or Diesel - .020 inch Main Bearing Kit. For 200B, 200, 203, 205, 20C, 20, 2135, 2200, 2244, 2500, 30B, 35, 40, 4500, FE35, MF135, MF150, MF230, MF235, MF245, MF250, MF35, MF50 with AG3-152 Perkins Gas Engine or A3-152 and AD3-152 Diesel Engines. Thrust washers not included. Complete for 1 engine. Replaces 746158M91 (Item #: 107164, Ref: 746158M91) $18.40

No
Picture
Main Bearing Set, .020, Z134-Z145 Gas - Main bearing set .020 inch for tractors using Continental Z134 or Z145 Gas Engines: 35, 50, 135, 150, 202, 204, F40, MH50, TO35. Complete for 1 engine. (Item #: 107159, Ref: 830639M91) $112.00

No
Picture
Main Bearing Set, .030, Perkins 152 Gas or Diesel - .030 inch Main Bearing Kit. For 200B, 200, 203, 205, 20C, 20, 2135, 2200, 2244, 2500, 30B, 35, 40, 4500, FE35, MF135, MF150, MF230, MF235, MF245, MF250, MF35, MF50 with AG3-152 Perkins Gas Engine or A3-152 and AD3-152 Diesel Engines. Thrust washers not included. Complete for 1 engine. Replaces 746159M91 (Item #: 107165, Ref: 746159M91) $12.80

No
Picture
Main Bearing Set, .030, Z134-Z145 Gas - Main bearing set .030 inch for tractors using Continental Z134 or Z145 Gas Engines: 35, 50, 135, 150, 202, 204, F40, MH50, TO35. Complete for 1 engine. (Item #: 107160, Ref: 830639-030) $141.00

No
Picture
Main Bearing Set, .040, Z134-Z145 Gas - Main bearing set .040 inch for tractors using Continental Z134 or Z145 Gas Engines: 35, 50, 135, 150, 202, 204, F40, MH50, TO35. Complete for 1 engine. (Item #: 830516M91) $86.27

No
Picture
Main Bearing Set, .060, Z134-Z145 Gas - .060 inch. For tractors using Continental Z134 or Z145 Gas Engines: 35, 50, 135, 150, 202, 204, F40, MH50, TO35. Complete for 1 engine. (Item #: MS-202P-060) $133.98

Main Bearing Set, STD, Perkins 152 Gas or Diesel - Fits 152 CID 3 cylinder gas or diesel engines. Standard Main Bearing Kit (4 pr). Thrust washers not included. Complete for 1 engine. For tractor models MF250, MF235, MF245, 20C, 30B, 200B, 2500, 4500, 20, MF230, 200, 2244, 2200, 2500, 203, 205, 40, MF135, MF150, 35, FE35, MF35, MF50. Replaces 746156M91 (Item #: 107162, Ref: 746156M91) $15.30

Main Bearing Set, STD, Z134-Z145 Gas - Main bearing set STANDARD for tractors using Continental Z134 or Z145 gas engines: 35, 50, 135, 150, 202, 204, F40, MH50, TO35. Complete for 1 engine. (Item #: 107157, Ref: 837155M91) $104.00

Piston Pin Bushing Set - Bushing kit, 4-760916M1 pin bushings. For 202, 204, F40, MF135, MF150, MF35, MF50, MH50, TE20, TO20, TO30, TO35 all with Continental Gas Engines. (Item #: 182637, Ref: 840708M91) $26.00

No
Picture
Rod Bearing, .002 - Connecting Rod Bearing, single .002 inch undersize, for Continental Gasoline Engines Z120, Z129, Z134, and Z145. Tractors: TE20, TO20, TO30, TO35, 35, F40, MH50, 50, 135 Special, 135 Deluxe, 150; Industrials: 202, 204. (Item #: 106983, Ref: 830508M91) $25.00

Rod Bearing, .020 - Connecting Rod Bearing, .020 inch undersize, for Continental Gasoline Engines Z120, Z129, Z134, and Z145. Tractors: TE20, TO20, TO30, TO35, 35, F40, MH50, 50, 135 Special, 135 Deluxe, 150; Industrials: 202, 204. Four required per engine. Sold per journal. (Item #: 106985, Ref: 830510M91) $15.00

No
Picture
Rod Bearing Set - For Massey Ferguson tractor models 20, 35, 40, 50, 135, 150, 154-4, 230 (s/n 9A349239-earlier), 231S, 235, 240 (s/n N01001-earlier), 241, 245 (s/n 9A349239-earlier), 250, 251XE, 253, 254-4 (s/n 22210641-earlier), 254-4 (s/n 22210641-later), 263, 360, 451, 2135, 2200, 3315, 3330, 3340, 3350, 3355, Compatible with Massey Ferguson Construction and industrial models 20F, 30B, 30D Replaces Massey Ferguson OEM number 737071M91, , Compatible with Massey Harris tractor models 50, Replaces OEM number 31131172, Set of 3, 6 Halves, (Item #: 166853) $9.80

No
Picture
Rod Bearing Set, .010 - Connecting Rod Bearing Kit, .010 inch undersize, for Continental Gasoline Engines Z120, Z129, Z134, and Z145. Tractors: TE20, TO20, TO30, TO35, 35, F40, MH50, 50, 135 Special, 135 Deluxe, 150; Industrials: 202, 204. Complete for one engine. (Item #: 185224, Ref: 830509M91) $95.00

No
Picture
Rod Bearing Set, .010, Perkins 152 Gas or Diesel - Rod Bearing Set .010 inch. For: 200B, 200, 203, 205, 20C, 20, 2135, 2200, 2244, 2500, 30B, 35, 40, 4500, FE35, MF135, MF150, MF230, MF235, MF245, MF250, MF35, MF50 with AG3-152 Perkins Gas Engine or A3-152 and AD3-152 Diesel Engines. Complete for 1 engine. Replaces 737071M91 (Item #: 106997, Ref: 737071M91) $10.10

No
Picture
Rod Bearing Set, .020, Perkins 152 Gas or Diesel - Rod Bearing Set .020 inch. For: 200B, 200, 203, 205, 20C, 20, 2135, 2200, 2244, 2500, 30B, 35, 40, 4500, FE35, MF135, MF150, MF230, MF235, MF245, MF250, MF35, MF50 with AG3-152 Perkins Gas Engine, or A3-152 and AD3-152 Diesel Engines. Complete for 1 engine. Replaces 737072M91 (Item #: 106998, Ref: 737072M91) $10.60

Rod Bearing Set, .030 - Connecting Rod Bearing Kit, .030 inch undersize, for Continental Gasoline Engines Z120, Z129, Z134, and Z145. Tractors: TE20, TO20, TO30, TO35, 35, F40, MH50, 50, 135 Special, 135 Deluxe, 150; Industrials: 202, 204. Complete for one engine. (Item #: 183864, Ref: 830510-030) $49.00

No
Picture
Rod Bearing Set, .030, Perkins 152 Gas or Diesel - Rod Bearing Set .030 inch. For: 200B, 200, MH203, 205, 20C, 20, 2135, 2200, 2244, 2500, 30B, 35, 40, 4500, FE35, MF135, MF150, MF230, MF235, MF245, MF250, MF35, MF50 with AG3-152 Perkins Gas Engine, or A3-152 and AD3-152 Diesel Engines. Complete for 1 engine. Replaces 737073M91 (Item #: 106999, Ref: 737073M91) $10.72

Rod Bearing Set, STD, Perkins 152 Gas or Diesel - Rod Bearing Set STANDARD. For: 200B, 200, 203, 205, 20C, 20, 2135, 2200, 2244, 2500, 30B, 35, 40, 4500, FE35, MF135, MF150, MF230, MF235, MF245, MF250, MF35, MF50 with AG3-152 Perkins Gas Engine, or A3-152 and AD3-152 Diesel Engines. Complete for 1 engine. Replaces 737070M91 (Item #: 106996, Ref: 737070M91) $11.20

No
Picture
Rod Bearing, Standard - Single rod bearing for Continental Gasoline Engines Z120, Z129, Z134, and Z145. Tractors: TE20, TO20, TO30, TO35, 35, F40, MH50, 50, 135 Special, 135 Deluxe, 150; Industrials: 202, 204. (Item #: 106982, Ref: 830486M91) $13.30

Sealing Ring - For Massey Ferguson tractor models 20, 30, 31, 35, 35X, 135, 148, 150, 165, 175, 178, 180, 230, 231, 235, 240, 245, 250, 253, 255, 261, 265, 270, 275, 282, 283, 285, 290, 292, 298, 360, 362, 365, 372, 375, 382, 383, 390, 390T, 393, 396, 398, 399, 420, 440, 492, 550, 565, 575, 590, 595, 670, 675, 690, 698, 699, Replaces Massey Ferguson OEM number 3699909M1, 907315M2, 3609471M1, 3699909V1, 186198M1, 2" O.D. x 3/32", (Item #: 165441) $3.98

Thrust Washer Set - 4 Pieces - Tabbed. Fits 152 CID 3 cylinder, 203 CID 4 cylinder gas or diesel engines. For tractor models 2500, 20, 40, MF135, MF150, 203, 205, 35, FE35, MF35, MF50, 200, 2244, 2200, 2500, MF235, 200B, 4500, MF230, 20C, 30B, MF245, MF250, 356, MF65, 300, 302, 304, 3165, MF165, 40B, 50.735113M1 (Item #: 107167, Ref: 31137211_21) $7.00

Wrist Pin Bushing - This Wrist Pin Bushing is used in 23C Standard Diesel Engines. 4 used per engine. Sold individually. Replaces 1884944M1, 826076M1 (Item #: 180006, Ref: 1884944M1) $7.20

Engine Gaskets

Bottom Gasket Set - Fits 23C Standard Motors Diesel Engine. For tractor models TO35, MF35, FE35, TEF20. (Item #: 173687, Ref: S.40603) $24.30

Carburetor Gasket - For Massey Ferguson tractor models F40, TE20, TO20, TO30, TO35, 35, 135, 150, Replaces Massey Ferguson OEM number 181531M2, (Item #: 161242) $1.50

Combustion Cap Gasket - This Copper combustion cap gasket fits 65, 65UK, 35, 50, 203, 205. Replaces 957E6K003, 81803686, 36241505, 490023, 734178M1, 746473M1. (Item #: 117404, Ref: 957E6K003) $2.60

Crank Seal, Front - Lip-Type. Fits Four Cylinder Continental Gas Engines. For 135, 202, 204, F40, MF135, MF150, MF35, MF50, MH50, TE20, TO20, TO30, TO35, Replaces: 1008597M1, 15287A, 843893M1, 850185M1. (Item #: 167998, Ref: 15287A) $9.60

Crank Seal, Rear - Lip-Type. Fits Four Cylinder Continental Engines. For 135, 202, 204, F40, MF135, MF150, MF165, MF35, MF50, MF65, MH50, TE20, TO20, TO30, TO35. (Item #: 106079, Ref: 1750216M92) $10.40

Crankshaft seal, Front Lip Type, Perkins - Fits 152 CID 3 cylinder or 203 CID 4 cylinder gas or diesel engines. For tractor models 2500, 20, 40, MF135, MF150, 203 and 205 to serial number 659002115, 35, FE35, MF35, MF50, 2135, MF235 engine serial number ending in D, 200B, 4500, MF230, 20C, 30B, MF245, MF250, 356, MF65, 300, 302, 304, 3165, 40B, 50, MF165, MF255. (Item #: 107221, Ref: 1851747M1) $9.20

Crankshaft Seal Kit - Kit contains front and rear crank lip-type seals and gasket for rear and felt seal for front. For Continental Gas Engines: Z120, Z129, Z134, Z145. Tractor Models: TO20, TE20, TO30, TO35, F40, MF50, MF35, MF135, MF150, 202, 204. Replaces: 1500080M1, 15287A, 15288A, 1750112M1, 1750216M1, 1750216M92, 843893M1, 850185M1. (Item #: 173222, Ref: VPC5122) $24.50

Crankshaft Seal, Rear Rope Type, Perkins - Sold individually - requires 2. Fits 152 CID 3 cylinder, 203 CID 4 cylinder gas or diesel engines. For tractor models 2500, 20, 40, MF135, MF150, 203, 205, 35, FE35, MF35, MF50, 200, 2244, 2200, 2500, 2135, MF235, 200B, 4500, MF230, 20C, 30B, MF245, 356, MF65, 300, 302, 304, 3165, MF165, 30, 40B, 50, MF255. (Item #: 107228, Ref: 735866M1) $2.60

Gasket Engine Bottom Set, Perkins 152 Diesel - For (203, 205 tractor serial number 659002115), FE35, 35, 50, all with A3-152 Regular Injection Perkins Diesel prior to engine serial numer 19B8552, injectors vertical in cylinder head, 3 cylinder. For engines using 2 piece rope type rear seal. Seals are included in engine kits but are not included in gasket sets. Bottom Engine Gasket Set. Use with part number 747166M91 for complete Engine Gasket Set. (Item #: 167681, Ref: 747187M91) $26.70

Gasket Set - Valve grinding set. Used on Z134 or Z145 CID Four Cylinder Continental Gas engines For tractor models 135, 202, 204, F40, MF135, MF150, MF35, MF50, MH50, TO35. Does not include exhaust valve seals - Order separately. Contains 1750045M1 Manifold Gasket, 1750017M1 Head Gasket, 181528M1 Thermostat Body Gasket, 181526M1 Water Outlet Elbow Gasket, 2 - 11277X Cylinder Cover Stud Gaskets, 1750006M1 Vent Tube Gasket, 4 - 1750062M1 Intake Valve Seals, 1750002M1 Valve Cover Gasket. (Item #: 107248, Ref: 836287M91) $42.10

Gasket Set - Overhaul Gasket Set. For tractor models TO35, 35, MF40, MH50, 50, 135 SPECIAL, 135 Deluxe, 150, all with Z134 Continental Gas Engine, (with front seals). Does not come with sleeve seals. (Item #: 107298, Ref: 830689M91) $63.00

Gasket Set, Bottom Engine, Perkins 152 Diesel - Bottom engine set for a 152 cubic inch 3 Cylinder Perkins Diesel engines above serial number 19B8552. For models 200, 203, 205, 20C, 20, 2135, 2200, 2244, 2500, 30B, 35, 40, FE35, MF135, MF150, MF235, MF245, MF35, MF50. Lower engine gasket sets are for engines using 2 piece rope type rear seal. Crankshaft Seals are not included. (Item #: 107305, Ref: 735232M92) $32.60

Gasket Set, Top Engine, Perkins 152 Diesel - For (203, 205 tractor serial number 659002115), FE35, 35, 50, all with A3-152 Regular Injection Perkins Diesel, injectors vertical in cylinder head, 3 cylinder. Top Engine Gasket Set. Use with part number 747187M91 for complete Engine Gasket Set. (Item #: 107249, Ref: 747166M91) $29.20

Head Gasket - Head Gasket, 4-cylinder Continental gas engine. For tractor models 202, 204, F40, MF135, MF150, MF35, MF50, MH50, TO35. Does not include exhaust valve seals. (Item #: 109786, Ref: 1750017M1) $35.20

Main Bearing Cap Packing - Rear Main Bearing Cap Packing for Z120, Z129 and Z134 engine. Not included in Overhaul Gasket Set. Replaces 1021673M1 (Item #: 173240, Ref: 1006635M1) $4.70

Oil Pan Gasket - For tractor models TE20, TO20, TO30, TO35, 35, 135, 150, 202, 204, 20C, 2135, 2200, 230, 235, 245, 2500, 30B, 4500, 40, 35, 50. All Continental 4 cylinder engines. Replaces 1750024M1 (Item #: 107278, Ref: 1750024M1) $7.30

Oil Pan Gasket, Perkins 152 Gas or Diesel - Oil pan gasket. For 20, 200B, 203, 205, 20C, 2500, 30B, 35, 40, 4500, FE35, MF135, MF150, MF230, MF235, MF245, MF35, MF50. (Item #: 107280, Ref: MF3152PG) $8.40

No
Picture
Oil Pump Body Cover Gasket - For Massey Ferguson tractor models F40, TO35, 35, 50, Replaces Massey Ferguson OEM number 1750087M1, (Item #: 173647) $2.70

No
Picture
Pan Gasket - This pan gasket is a 4 piece set for the Perkins AD3.152 and A3.152 engine in models 40, 135, 148, 254, 35. (Item #: 107280, Ref: VPC5346) $8.40

Rear Head Cover Gasket - For Massey Ferguson tractor models 20, 30, 35, 35X, 40, 50, 50A, 65, 80, 135, 150, 154, 154-4, 165, 230, 231, 235, 240, 245, 250, 254, 254-4, 255, 302, 304, 360, 364S, 399, 699, 1100, 1105, 1130, 1135, 2135, 2200, 2640, 3090, 3165, 3505, 3525, 3545, 3630, 3650, Compatible with Massey Ferguson Combine (s) 300, 510, 550, 750, 760, 850, 855, 860, 865, Compatible with Massey Ferguson Construction and industrial models 20, 40, 80, 203, 2200, 2500, 4500 Replaces Massey Ferguson OEM number 4222004M1, 731128M1, , Compatible with Oliver tractor models 1850 Replaces Oliver OEM number 159070A, , Compatible with White tractor models 2-85, 2-88, 2-105, 2-110, Replaces White OEM number 159070A, Replaces Perkins OEM number 36851416, 490485, (Item #: 113596) $9.30

Rocker Cover Gasket - For tractor models TE20, TO20, TO30, TO35, 135, 150, 202, 204, 20C, 2135, 2200, 230, 235, 245, 2500, 30B, 4500, F40, 35, 50. All using Continental Z120, Z129 or Z134 gas engines. (Item #: 110187, Ref: 1750002M1) $6.50

Rope Seal Housing Gasket - This Rope Seal Housing Gasket is used on Perkins 144, 152 and 203 cubic inch, three and four cylinder engines with rope type rear seals. Replaces part numbers 957E6344A, 83934357, 136817168, 36817134, 36817168, 27847, 734664M1, 36817134, 734664M91, 4222068M1, 4222068V1 (Item #: 168419, Ref: 36817134) $4.80

No
Picture
Steering Shaft Seal, Felt - For Massey Ferguson tractor models 35, 35X, 133, 135, 140, 148, 158, 230, 231, 235, 240, 245, 250, 255, 260, Compatible with Massey Ferguson Construction and industrial models 20D, 20E, 30E, Replaces Massey Ferguson OEM number 1850020M1, 1850020V1, Power Steering, (Item #: 168938) $2.00

Timing Case to Block Gasket - Gasket for the timing case to block for tractor models Massey Ferguson 35, 135, 148, 230, 240, 250, 254, 254S, 255, 350, 353, 550, 363, and 253 with Engines A3.152 AD3.152 AT3.152 AT3.152.4 Replaces 36814119. Priced each. Price shown is for 2, sold only in multiples of 2 items. (Item #: 168423, Ref: 734238M1) $13.20

Timing Cover Gasket - For tractor models F40, TO35, 35, 50, MH50, 135, 150, 202, 204, 20C, 2135, 2200, 230, 235, 245, 2500, 30B, 4500 all with Continental Z134 Engine. (Item #: 111985, Ref: 1750032M1) $3.40

No
Picture
Timing Cover Gasket - For Massey Ferguson tractor models TE20, TEA20, 35, 135, Replaces Massey Ferguson OEM number 825649M1, 3910265M1, 825649M2, (Item #: 183899) $6.60

Top Gasket Set - Fits 23C Standard Motors Diesel Engine. TO35, FE35, TEF20, MF35. Replaces 1810028M91 (Item #: 184618, Ref: S.40587) $76.00

Valve Cover Gasket - This Valve Cover Gasket is used on Massey Ferguson 35, 50, 203 and 205 all with A3.152 Perkins Diesel Engines. Replace Perkins 040491 and Massey Ferguson 731273M1 (Item #: 173313, Ref: 0490491) $3.40

Valve Cover Vent Gasket - This valve cover vent gasket is used on Ferguson, Massey Ferguson and Massey Harris Tractors with Continental Gas Engines. It replaces part numbers 1750006M1, Z129A204. (Item #: 173372, Ref: 1750006M1) $2.60

Engine Rebuild Kits

Basic Engine Overhaul Kit, Perkins 152 Diesel - For FE35, 35, 50; Industrial 35 Utility, all with A3-152 Regular Injection Perkins Diesel with vertical injectors in cylinder head, standard bore 3.6 inch. Up to serial number 1935854 (.040 SLEEVE FLANGE THICKNESS). Basic Engine Overhaul Kit. Contains Sleeve and Piston Kit: sleeves, pistons, rings, pins and retainers. Pin Bushings. Complete Gasket Set. Engine bearings and thrust washers must be ordered separately. (Item #: 130742, Ref: BEKP1335D-LCB) $310.00

No
Picture
Basic Engine Rebuild Kit, Less Bearings - For Massey Ferguson tractor models F40, TO35, 35, 50, 135, 202, 204, Kit Contains: sleeves and sleeve seals, pistons and rings, pins and retainers, pin bushings, complete gasket set, crankshaft seals, For Basic Engine Rebuild Kit with Bearings use Item #: 184021, (Item #: 183956) $354.40

Basic In-Frame Engine Kit, Perkins 152 Diesel - For (203, 205 tractor serial number 659002115), FE35, MF35, MF50, 35. Perkins A3-152 diesel, serial number up to 193585, regular injection, using 2 piece rope type rear seal, .040 inch sleeve flange thickness, 3.6 inch standard bore. Basic In-Frame Engine Kit includes: Sleeve and Piston Kit with rings, pins and retainers, top engine set and oil pan gasket. (Item #: 191769, Ref: BIFP1335D) $266.00

Basic In-Frame Engine Kit, Perkins 152 Diesel - For (203, 205 tractor serial number 659002115) FE35, 35, 50. Perkins A3-152 diesel, regular injection, injectors vertical in head, 3.6 inch standard bore, using 2 piece rope type rear seal, .150 inch sleeve flange thickness. Basic In-Frame Engine Kit includes: sleeve and piston kit with rings, pins and retainers, top engine set and oil pan gasket. For engines serial number 193585 and up. (Item #: 189683, Ref: BIFP1336D) $195.00

Basic Overhaul Kit, Less Bearings - Z134 - (NOT FOR Z145) Basic Engine Kit. Continental Z134 CID Gas Engine, 4 cylinder, 3 3/8 inch overbore. Contains sleeves, sleeve seals, pistons and rings, pins and retainers, gasket sets, crankshaft seals. For 135, 202, 204, F40, MF135, MF35, MF50, MH50, TO35. (Item #: 130844, Ref: BEKM119-LCB) $413.00

Basic Overhaul Kit, Perkins 152 Diesel - 152 CID 3 cylinder diesel engine 3.6 inch standard bore, injectors vertical in head. Basic Engine Kit. Contains CAST sleeves, .150 inch flange thickness, pistons and rings, pins and retainers, pin bushings, gasket sets, crankshaft seals. For 203, (prior to serial number 65902115) 205, (prior to serial number 65902115) 35, FE35, MF35, MF50. Engine Bearing and thrust washers must be ordered separately. Please see "engine bearings". (Item #: 183957, Ref: BEKP1336D-LCB) $399.00

Cylinder Kit - Chrome Liner - Single Cylinder - For Massey Ferguson tractor models 35 (engine s/n 1935853-earlier), 35X (engine s/n 1935853-earlier), 65 (engine s/n 2820092-earlier), Compatible with Massey Ferguson Construction and industrial models 65 (engine s/n 2820092-earlier), 203 (s/n 1935853-earlier), 205 (s/n 1935853-earlier) Replaces Massey Ferguson OEM number 3639471M1, , Compatible with Perkins Engine (s) A3.152 (indirect injection), A4.203 (indirect injection), 3.152 (indirect injection), Replaces Perkins OEM number U5MK0064, Bore: 3.6", Kit includes: Chrome cylinder liner, piston, piston rings, piston pin, and retainers, Sold per cylinder, (Item #: 191119) $211.00

Engine Overhaul Kit, Perkins 152 Diesel - For (203, 205 tractor serial number 659002115) FE35, 35, 50; Industrial 35 Utility, all with A3-152 Regular Injection Perkins Diesel with vertical injectors in cylinder head, 3.6 inch standard bore. (.150 SLEEVE FLANGE THICKNESS). Basic Engine Overhaul Kit. Contains Sleeve and Piston Kit: sleeves, pistons, rings, pins and retainers. Pin Bushings. Complete Gasket Set. Intake and Exhaust valves, valve keys, guides and springs. Engine bearings and thrust washers must be ordered separately. Please see "engine bearings". (Item #: 185350, Ref: EOK1336D-LCB) $568.00

Engine Overhaul Kit with New Crankshaft - Comprehensive Kit. For A3-152 3 Cylinder DIESEL Regular (INDIRECT) Injection CHROME LINERS, identify by: Vertical Injectors, 0.040 inch Deep Liner Flange, Rope Type Rear Crank Seal, Flat Top Pistons 3.6 inch bore, up to engine number CL1935853 -Including New Crankshaft Kit. Includes - Pistons, Wrist Pin Bushings, Piston Rings, Liners, Con Rod Bearings, Con Rod Lock Nuts (where fitted), Top and Bottom Gasket Sets, Main Bearings, Thrust Washers, Front and Rear Seals AND A NEW CRANKSHAFT. FOR MODELS MF35, MF50. (Item #: 183925, Ref: EKMC5) $1189.01

Engine Overhaul Kit with New Crankshaft - Comprehensive Kit. A3-152 3 Cylinder DIESEL Engine, Regular (INDIRECT) Injection CAST LINERS, identify by: Vertical Injectors, 0.150 inch Deep Liner Flange, Rope Type Rear Crank Seal, Flat Top Pistons 3.6 inch bore. From engine number 1935854. -Including New Crankshaft Kit. Includes - Pistons, Wrist Pin Bushings, Piston Rings, Liners, Con Rod Bearings, Con Rod Lock Nuts (where fitted), Top and Bottom Gasket Sets, Main Bearings, Thrust Washers, Front and Rear Seals AND A NEW CRANKSHAFT. FOR MODELS MF35, MF50. (Item #: 183924, Ref: EKMC6) $1129.01

Engine Rebuild Kit with Valve Train - Less Bearings - ESN 1935854-later, Perkins, 3.152 - For Massey Ferguson tractor models 35, 50, Compatible with Massey Ferguson Construction and industrial models 203, 205, Compatible with Perkins Engine (s) 3.152 (diesel, CD Build, indirect injection, s/n 1935854-later), Bore: 3.602", Flat top piston, 15 head studs, Vertical nozzles, .150" sleeve flange thickness, Kit includes: Pistons, Piston Ring Set, Liners, Connecting Rod Bushings, Gasket set with Crank Seals, and Valve Train Set, Kit does not include connecting rod or main bearings, For thrust washer set use Item #: 107165, Additional Handling and Oversize Fees Apply To This Item, (Item #: 130866) $378.00

No
Picture
In-Frame Engine Kit, Standard Motors 87mm - In Frame Engine Overhaul Kit. 4 CYLINDER, STANDARD BORE: (87MM) Includes: pistons, sleeves, rings, pins, retainers, overhaul gasket set and connecting rod bearings (standard, .010, .020, .030). Specify bearing size in comments section when ordering online. For tractor models TEA20, TED20, FE35, 35UK, 135UK. (Item #: 172856, Ref: IK87MM) $289.98

Major Overhaul Kit with CRANKSHAFT - Overhaul Kit for Continental Z134 Gas Engine 3 3/8 Inch OVERBORE. Including New Crankshaft Kit. Includes - pistons, wrist pin bushings, piston rings, liners, connecting rod bearings, connecting rod lock nuts (where fitted), top and bottom gasket sets, main bearings, thrust washers, front and rear seals AND A NEW CRANKSHAFT. Wrist pin bushings must be machined and pressed in. FOR MODELS TO35, MF35, MF50, MF135 Special, F40, MH50 Industrial 202, 204 B-C. (Item #: 183992, Ref: EKMC132) $1269.01

Overhaul Kit, Less Bearings - Z134 - Engine Overhaul Kit. Contains sleeves, sleeve seals, pistons and rings, pins and retainers, pin bushings, complete gasket set, crankshaft seals, intake valves and exhaust valves, valve keys, springs and guides. For 135, 202, 204, F40, MF135, MF35, MF50, MH50, TO35. Does not include exhaust valve seals. Order separately. (Item #: 184881, Ref: EOK119-LCB) $636.75

No
Picture
Valve Overhaul Kit, Perkins 152 Diesel - Fits 152 CID 3 Cylinder Diesel Engines, 3.6 inch standard bore, injectors vertical in head, .040 inch sleeve flange thickness. Kit contains, intake and exhaust valves, springs, keys and guides. For tractor models (203, 205 tractor serial number 659002115), 35, 50, FE35. (Item #: 120300, Ref: VOKP152) $85.00

Valve Overhaul Kit, Z129 or Z134 Engines - For TO30, TO35, 35, F40, MH50, 50, 135 Special, all with 4 cylinder Z129 or Z134 Continental Engine. Engine Valve Overhaul Kit includes: pin type intake and key type exhaust valves, valve springs, valve keys and valve guides. Replaces: keeper half: 1004512M1, keeper pin: 18291A, valve spring: 21176A, intake valve: 830487M91, 1750070M1, exhaust valve: 830488M91, 1750072M1, valve guide: 830490M91, 1750069M1. (Item #: 107487, Ref: VOKM129) $118.00

Engine Parts

Camshaft - For Z120, Z129, or Z134 Continental Engines on TE20, TO20, TO30, T035, 135, 202, 204, 2135, 2200, 30, 35, 50. Replaces 1500098M1, 1750074M1, 1750293M1, 836543M91. (Item #: 110977, Ref: 836543M1) $142.00

Camshaft - Replaces 31415261. For the following Models with A3.152, AD3.152 or AG3.152 engines: 135, 150, 154-4, 1545, 20, 20C, 20D, 20F, 200, 203, 205, 2135, 2200, 2244, 230, 231, 235, 240, 2400, 245, 250, 2500, 253, 254-4, 30B, 30D, 30E, 30H, 35, 350, 360, 40, 40E, 4830FC, 50, 5500, 5830, 5830FC, 5860, 5870, 6030C, 7830, 7830C, 8830 (Item #: 173283, Ref: 733507M1) $131.00

Camshaft Gear - Camshaft gear, 48 teeth, Continental Gas Engine in models: TE20, TO20, TO30, TO35, 35, F40, MH50, 50, 135, 150; Industrials: 202, 204, 2135. Replaces: 1046676M1, 1750237M1. (Item #: 121582, Ref: 1750237M1) $102.00

Camshaft Idler Gear - 90 tooth. For tractor models (135, 148, 150, 154-4, 154-4S, 20, 200, 203, 205, 20C, 20D, 20F, 2135, 220, 2200, 2244, 230, 231, 235, 240, 245, 250, 2500, 253, 254-4, 30b, 30D, 30E, 30H, 35, 40, 40E, 4500, 4830FC, 50, 550 all with A3.152 or AD3.152 gas or diesel engines), 5830, 5830FC, 5860, 5870, 6030FC. Replaces 31164362. (Item #: 172340, Ref: 731205M2) $82.00

Camshaft Timing Gear - 50 tooth, for engine type PE 144 A3.152/AD3.152, replaces 410241. For tractor models 135, 148, 150, 154-4, 1545, 20, 200, 203, 205, 20C, 20F, 2135, 220, 2200, 2244, 230, 231, 235, 240, 240P, 245, 250, 2500, 253, 254-4, 30B, 30E, 30H, 35, 40, 40E, 4830FC, 50, 550, 5830, 5830FC, 5860, 5870, 6030FC, TE20. Replaces 3637541M1, 410241, 4224245M1, 731203M1, 957E6256, 81804014, 2190007, 72080139 (Item #: 172327, Ref: 731203M1) $45.01

Combustion Chamber Cap - This Combustion Chamber Cap is used on Massey Ferguson Tractors 65, 35, 50, 203, 205, using Perkins Engines. It replaces original part numbers 37416203, 37416511, 746472M1. (Item #: 184439, Ref: 746472M1) $43.00

Connecting Rod - Verify casting number 0210007. For tractor models (135, 150, 20, 200, 203, 205, 2135, 220, 2200, 2244, 230, 235, 2500, 34B, 35, 356, 40, 50 with engine serial number ending in D, DL or DSL), 65. Has 9 inch CENTER TO CENTER measurement. (IF NEEDING 8.875 inch CENTER TO CENTER, ORDER PART NUMBER ZZ90010). Replaces: M7BJ0052, VPB6000, 3637439M91, 3637439V91, 52813, 59908, 731676M91, 735391M91, 747010M91, 747101M91, 81803971, 957E6200. (Item #: 173358, Ref: ZZ90011) $76.00

Connecting Rod Bolt and Nut Assembly - Used on Perkins Engines, this Bolt and Nut Assembly replaces OEM numbers 84264589, 370664S, 382885S2, 34447ES2B, 385279S2, 390655S2, 81803991, 957E6215, 957E6212, 957E-6215, 0095250, 1476245, 1476245X1, 375756X1, 355756X1, 33221327, 3639947M1, 33221319 (Item #: 183833, Ref: 957E6215) $4.90

Connecting Rod, Used - For Massey Ferguson tractor models TE20, TO20, TO30, TO35, 35, 50, 135, 150, 2135, 2200, Replaces Massey Ferguson OEM nos 830644M91, 1046982M91, Replaces Massey Ferguson Casting nos Z120D500, Used items are not always in stock. If we are unable to ship this part we will contact you within one business day., (Item #: 430302) $82.01

Crankshaft - New Crankshaft only (bearings not included) for Continental Z129 and Z134 Gas Engines. For TO30, TO35, 35, 50, MH50, 135, 202, 204 . See our engine bearings category for prices and sizes. Also replaces 1750169M1. (Item #: 102110, Ref: 830686M91) $429.00

Crankshaft - New. For Perkins 3 cylinder using ROPE SEAL. Note: In some cases you may have to reuse your old balancer weights. Call for details. Fits Perkins A3.152 and AD3.152 engines. Fits 50, 35, 30, 135, 235, Ind 20, 40, 202 Workbull, 2135, 2200. (Item #: 102112, Ref: 736532M91) $343.00

Crankshaft Assembly - Crankshaft kit with standard rod and main bearings and thrust washers. For Perkins Diesel A3-152 and AD3-152. Also Perkins 3 Cylinder gas with rope type rear seal. For 200, 203, 205, 20, 2135, 2200, 2244, 2500, 35, 40, MF135, MF150, MF235, MF35. This is for a 2 piece rope seal. (Item #: 168650, Ref: 3638309M91) $430.00

Crankshaft Gear - Used on 3-cylinder Perkins A3.152 and AD3.152 engines on: 30, 35, 50, 135, 235, 245. INDUSTRIALS: 20, 40, 202, 2135, 2200. Replace 02139014, 31163411, 31163491, 31163492, 31163493, 31163494, 31163495, 3637518M1, 3641085M1, 3641397M91, 3641826M1, 410132, 731228M1, 735599M1, 81804043, 957E6306 (Item #: 113700, Ref: 731228M1) $40.10

Crankshaft Gear - Crankshaft Gear, 24 teeth. For tractor models TO35, 35, MH50, 50, 135, 150. Continental Gas Engine. (Item #: 121584, Ref: 1750054M1) $55.00

Crankshaft Kit with Bearings - Kit includes main and rod bearings and thrust washers. For 235 with Perkins <152UA381043DL 3.152 Diesel WITH ROPE SEAL, engine serial number ending with DS, (203, 205, 2135, all with Perkins A3.152 or AD3.152 Diesel Engine Sserial number ending with DS), (135, 150, 20, 2244, 35, 40, 50, all with Perkins A3.152 or AD3.152 Engine serial number <152UA381043DL). Uses 2 piece rope seal. Also Perkins 3 Cylinder Gas with Rope type seal. Replaces 084402, 736532M1. (Item #: 168650, Ref: 3638309M91) $430.00

Crankshaft Pulley - For tractor models (135, 20 with Perkins Gas Engine serial number up to 152UA25587A and all diesel engines), (2135 with diesel engine), (240 with AD3.152 Diesel Engine), (35 with Perkins Diesel Engine serial number 1861319 and up), 360. Replaces 31143733. (Item #: 173096, Ref: 734627M1) $62.00

Crankshaft Pulley - For tractor models TO35, MF35, MH50, MF50, 65, 202, 204 with Continental Engine. 4 hole, spoked pulley with 7/16 inch holes, 2 3/4 inch center to center hole spacing. (Item #: 164737, Ref: 1750076M1) $103.00

Crankshaft Pulley, 3-Hole - For Perkins Engines. Fits Massey Ferguson Forklifts: 2500 and 4500. Massey Ferguson Industrial: 20 (Gas Engine serial number <152UA22587A, All Diesels), 20C (Diesel) 20D, 20F, 203 (Diesel), 205 (Diesel), 2135 (Utility), 2200, 30B (Diesel), 30D, 30E, 30H, 40 (Gas Engine serial number <152UA22587A, All Diesels), 40E, Tractors: TO35 (Equipped with 102 Loader), 135 (Gas Engine serial number <152UA22587A, All Diesel), 150 (Gas Engine serial number <152UA22587A, All Diesel), 230, 235 (Orchard), 245 (Orchard), 35 (Diesel), 35X (FE) (Diesel), 50 (Diesel), 65 (Engine serial nubmer <2820092). Uses 704812M93 hydraulic adapter plate. Replaces 31147784. (Item #: 118287, Ref: 734628M1) $78.00

No
Picture
Crankshaft, Remanufactured, 260034 - For Massey Ferguson tractor models 35, 50, 150 (all gas or diesel, 3.152 Perkins with rope type rear seal and Keyed nose), Replaces Casting number 260034, 31312700, Our remanufactured crankshafts are cleaned, magnafluxed, measured and reground if necessary, the journals are then polished., (Item #: 200462) $475.01

No
Picture
Crankshaft, Remanufactured, Z134 - For Massey Ferguson tractor models TO35, 35, 50, Replaces Casting number Z134, Our remanufactured crankshafts are cleaned, magnafluxed, measured and reground if necessary, the journals are then polished., For a New version of this sku use Item #: 102110, (Item #: 200460) $535.01

Crankshaft Weight Washer - This Crankshaft Weight Washer is used on 35, 50, 135, 150, 230, 235, 245, 231, 240, 250, 253, 360, 362, 202, 203, 204, 205, 20, 2135, 20C, 30B, 40B, 20D, 30E, 40E. It replaces 31731515, 31731516, 733645M1, 733644M1 (Item #: 183801, Ref: 733644M1) $0.70

Cylinder Head - For tractor models 35, 50, (203 and 205 Industrials (All prior to serial number 1846220). Cylinder Head - Indirect Injection. Complete with Valves and Springs. Perkins A3.152. Replaces 3637784M91, 3638321M91, 731781M91, 743272M91, ZZ80058, E2046T9, M03-00-19, 58462, 68131, 82620, 86553, U5BD0024, ZZ80048. (Item #: 156259, Ref: 3637784M91) $437.00

Cylinder Head, Remanufactured, 37116190 - For Massey Ferguson tractor models 35, 135 (With Perkins Gas Engine), Replaces Massey Ferguson Casting number 37116190, Engine 152, Cylinders: 3, Casting No. 37116190, Our remanufactured cylinder heads are reconditioned and ready for assembly, with both valve guides and valve seats installed, Cleaned and tested for cracks, (Item #: 200497) $900.01

Cylinder Head, Remanufactured, Z134A601 - For Massey Ferguson tractor models TO35, 35, 40, 50, 135, 150, 202, 235, 245 (With Continental Gas Engine), Replaces Massey Ferguson Casting number Z134A601, Engine 134, Cylinders: 4, Not a welded head, Our remanufactured cylinder heads are reconditioned and ready for assembly, with both valve guides and valve seats installed, Cleaned and tested for cracks, (Item #: 200496) $730.01

Cylinder Head with Valves, Remanufactured, Z134A601 - For Massey Ferguson tractor models 35, 40, 50, 135, 150, 202, 235, 245 (With Continental Gas Engine), Replaces Massey Ferguson Casting number Z134A601, Engine 134, Cylinders: 4, Casting No. Z134A601, Our remanufactured cylinder heads are reconditioned and ready for assembly, with valves installed, Cleaned and tested for cracks, (Item #: 200513) $1275.01

No
Picture
Cylinder Head with Valves, Used - For Massey Ferguson tractor models 35, 40, 50, 135, 150, 202, 235, 245 (With Continental Gas Engine), Replaces Massey Ferguson Casting number Z134A601, Engine(s): 134, Cylinders: 4, Our used cylinder heads have been visually inspected for cracks, Cylinder head may require further cleaning, inspection, or machining before use, For a Remanufactured version of this part use Item #: 200513, Used items are not always in stock. If we are unable to ship this part we will contact you within one business day., (Item #: 400513) $445.01

Flywheel Gear, Perkins Engines - Flywheel Ring Gear. For Perkins engine in tractors: MF35, MF50, MF65, MF135, MF150, MF165, MF175, MF180, MF235, MF255, MF265, MF275, MF383, Industrials: 20, 30, 40, 50. 115 teeth, 13-7/16 inch inside diameter. Replaces 410236. For 20, 30, 40, 50, MF135, MF150, MF165, MF175, MF180, MF235, MF255, MF265, MF275, MF35, MF383, MF50, MF65. (Item #: 101977, Ref: 731008M1) $28.20

Flywheel Plate - For tractor models 20C, 20, 30B, 30D, 30, 40B, 40, MF135, MF150, MF165, MF175, MF180, MF230, MF235, MF245, MF255, MF265, MF35, MF50, MF65, TO35 (Item #: 173138, Ref: 1040886M1) $75.28

Flywheel Tab Washer - This Flywheel Tab Washer is used on Massey Ferguson 35, 50, 65, 135, 150, 165, 175, 180 230, 235, 245, 255, 265, 275, 231, 240, 250, 253, 360, 362, 270, 282, 283, 375, 383, 390, 390T, 398, 399, 202, 203, 204, 205, 302, 304, 20, 2135, 20C, 30B, 40B, 20D, 30E, 40E, 30, 31, 40, 3165. It Replaces 731192M1, 731192M1, 731192V1 (Item #: 153307, Ref: 731192M1) $1.40

No
Picture
Freeze Plug - Verify OEM part number of 159312A, 7208009, 731356V1. For tractor models 300, 410, 510, 540, 550, 750, 760, 850, 860, 2500, 4500, 20, 200, 2135, 2200, 30, 302, 304, 3165, 40, 50, 70, 80, 1130, 1135, 135, 150, 154-4, 165, 230, 231, 235, 240, 245, 250, 253, 254-4, 255, 263, 2640, 2675, 285, 298, 3090, 35, 35X, 3505, 3525, 3545, 3630, 364S, 3650, 399, MH50, 65, 698, 699. (Item #: 172875, Ref: 731356M1) $1.40

Freeze Plug - This Freeze Plug is 0.891 inches in diameter, 57/64 inch cup type. Used on Perkins engines. Verify size or part number before ordering. Replaces Massey Ferguson OEM nos 731999M1, Replaces JCB OEM nos 02100395, Replaces Leyland OEM nos AJR2098, Replaces Perkins OEM nos 0650664. (Item #: 174344) $1.90

Governor Assembly - Governor Assembly for Continental Engines in tractors: TE20, TO20, TO30, TO35, MF135, MF35, F40, MH50, MF50, MF150, Pony, 202, 204, 2135, 2200, 2500. Also fits: MF135, MF150, with Perkins gas. Replaces 1002849M91, 529737M1, 529737M91, 738440M91 (Item #: 118785, Ref: 529737M1) $103.00

Governor Compensating Spring - Fits the following tractors using Continental Gas Engine: TO20, TE20, TO30, TO35, F40, MF 35, 50, 135. INDUSTRIALS: 2135. (Item #: 178100, Ref: 181535M1) $10.00

Governor Shaft Seal - For tractor models TO20, TO30, TO35, 135, 150, 230, 235, 245, 35, 50. (Item #: 173207, Ref: 1750108M1) $4.70

No
Picture
Hand Starting Crank with Spinner - Hand Starting Crank WITH Spinner. For TE20, TO20, TO30, TO35, TE20 Ferguson Tractor and MF 35 Without Bumpers. (Item #: 126699, Ref: 351010R31-S) $72.00

Heater, Engine Block - For tractor models 135, 165, 180, 235, 265, 275, 285, 35, 50, 65, 85, 88, Super 90. Engine Block Frost Plug Heater has 3/4 inch NPT, is 400 Watt, used with MF Engine Heater Adapter part number 191184M1 (which we do not have available). (Item #: 111621, Ref: 773323M1) $49.80

Lifter - New Lifter for TO20, TO30, TO35, MF35, MF50, MF135, MF150, MF65, MF165, 175 all with Continental Gas Engines. (Item #: 161159, Ref: 1750111M1) $18.50

Multipower Transmission Clutch Kit - For Massey Ferguson tractor models 30, 35, 50, 65, 135 (UK), 150, 165 (UK), 178, 180, 235, 240, 245, 255, 265, 270, 275, 285, 290, 298, 360, 362, 375, 383, 390, 393, 396, 398, 399, 670, 690, 698, 699, 1080, 1085, Compatible with Massey Ferguson Construction and industrial models 20E, 30E, 40E, 50E, 50H, 60H, Replaces Massey Ferguson OEM number 1672626M1, 185425M1, 185464M1, 186519M1, 186580M1, (Item #: 168778) $242.00

No
Picture
Push Rod - For Diesel Engines AT6.354.4, A6.354.4, C4.236, T6.354, 6.354 Perkins, (AD3.152 with engine serial number less than 2820092). (Item #: 114553, Ref: 31434307) $5.50

Push Rod - This push rod fits the following tractor models: TE20, TO20, TO30, TO35, 35, F40, 50, 35, 150, 202, 204, 230, 235, 245, 30C, 30B, 2135, 2200, 2500, and 4500. All with the following Continental Gas or LP Engines: Z120, Z129, Z134, and Z145. 8.940 inch overall length, 0.250 inch outside diameter. Sold as a single rod and priced each. Replaces 1750058M1, Z120I-206. (Item #: 182470, Ref: MFS2420) $27.70

Rear Main Housing - For tractor models 135, 148, 254, 35, 65, 765 all with Perkins engines and rope type rear seal. Replaces 740235M91. (Item #: 172688, Ref: 4224172M1) $25.30

Ring Gear, Flywheel - This ring gear is for models TE20, TO20, TO30, TO35, 35, 50, 65, 135, 150, 165, 175, 180, all with Continental Gas Engine. Flywheel Ring Gear with 145 teeth measures 14.685 outside diameter and 13.680 inside diameter and 1/2 inch thick. (Item #: 101976, Ref: 1750034M1) $45.50

Rocker Arm Assembly - For Continental Z120, Z129, Z134, Z145 Gas Engines in models TE20, TO20, TO30, 35, F40, 50, 135, 150, 202, 204, 230, 235, 245, 30C, 30B, 2135, 2200, 2500, 4500. With forged ends. Replaces: (1) 1750073M1 rocker arm shaft, (2) 354043X1 cotter pin, (2) 1755067M1 washer, (2) 1750124M1 oil plug, (2) 1750056M1 rocker arm short spring, (4) 1750067M91 right rocker arm assembly, (4) 1750066M91 left rocker arm assembly, (3) 1750057M1 long shaft springs and (4) 1750055M1 support brackets. (Item #: 126173, Ref: MFS129) $270.00

Rocker Shaft - For tractor models 3 Cylinder Perkins 135, 150, 20, 200, 203, 205, 20C, 2135, 220, 2200 engine serial number ending in D, 2244, 230, 235, 245, 250, 2500, 30B, 35, 40, 50. Replaces 3637532M91, 731754M91, 1076971M91, U7LR0002, ZZ90047, 747938M91 (Item #: 133942, Ref: ZZ90047) $11.90

Rocker Shaft, Plug Type - Plugs NOT included (Note: Massey had two different types of ways to plug the end of these shafts. Some had threaded plugs, but this is the type that uses plugs that are pressed in.) For tractor models TO35, F40, 35, 50, 135, 150, 230, 235, 245, 20C, 30B, 2135. With Continental Z134 or Z145 gas engine. (Item #: 185557, Ref: 1750073M1) $35.40

Shift Rail, 1st and Reverse, Used - For Massey Ferguson tractor models TO35, 35, 50, 65, 135, 150, 165, 175, 180, 230, 231, 235, 240, 240P, 245, 250, 253, 255, 265, 270, 275, 282, 283, 285, 290, 298, 431, 451, 471, 481, 543, 583, 1080, 1085, Compatible with Massey Ferguson Construction and industrial models 20, 20C, 20D, 20F, 30, 30B, 30D, 30H, 31, 40, 40B, 40E, 50A, 50C, 50D, 50E, 50H, 202, 203, 204, 205, 302, 304, 2135, 2200, 3165, Replaces Massey Ferguson OEM number 180442M2, For a new version of this item use Item #: 172890, Used items are not always in stock. If we are unable to ship this part we will contact you within one business day., (Item #: 460983) $24.76

Shift Rail, 2nd and 4th, Used - For Massey Ferguson tractor models F40, TO35, 35, 50, 135, 150, 165, 175, 180, 230, 231, 235, 240, 240P, 245, 250, 253, 255, 265, 270, 275, 282, 283, 285, 290, 298, 431, 451, 471, 481, 543, 583, 1080, 1085, Compatible with Massey Ferguson Construction and industrial models 20, 20C, 20D, 20F, 30, 30B, 30D, 30E, 30H, 31, 40, 40B, 40E, 50A, 50C, 50D, 50E, 50H, 202, 203, 204, 205, 220, 302, 304, 2135, 2200, 2500, 3165, 4500, 6500, Replaces Massey Ferguson OEM number 180438M2, 1678866M1, For a new version of this item use Item #: 172896, Used items are not always in stock. If we are unable to ship this part we will contact you within one business day., (Item #: 460982) $22.01

No
Picture
SINGLE Valve Guide - Z134, Z129 or Z120 Gas - SINGLE Valve Guide for 135, 202, 204, F40, MF135, MF150, MF35, MF50, MH50, TE20, TO20, TO30, TO35 all with Z134, Z129 or Z120 Gas Engines. MUST ORDER 8 for complete engine. (Item #: 108035, Ref: 830490M91) $2.30

Starter Ring Gear - For TE20, TEA20. Starter Ring Gear for 85MM and 87MM Gasoline Engines, 145 teeth. 42422S (Item #: 159157, Ref: 825452M1) $83.00

Tappet, Perkins Diesel - Adjustable Tappet. Does not come with adjusting screw or nut. 353430X1 Nut and 32151116 Screw sold separately. Used on A3.144, A3.152, A4.192, A4.203, AD3.152, AD4.203 Gas and Diesel Perkins Engines. Replaces: 0860012, 731150M1, 957E6489, 81804255, 0860012, 41345 (Item #: 165601, Ref: 731150M1) $8.80

Valve, Exhaust - Exhaust valve, key-type. For Continental Gas Z129 and Z134 engines in models 135, 202, 204, F40, MF135, MF35, MF50, MH50, TO30, TO35. Price shown is for each. (Item #: 159420, Ref: 1750072M1) $11.00

Valve, Exhaust - Exhaust valve for engines 152, 203 or 305 CID diesel in models 203, 205, 35, 356, FE35, MF35, MF50, MF65, Super 92. (Item #: 166347, Ref: 731152M1) $5.90

Valve Guide, Intake - This Intake Valve Guide is for tractor models TEA20, TED20, FE35 with 80, 85, 87 Gas or 35, TO30 using 23C Diesel Engines. (Item #: 164339, Ref: 825259M1) $11.10

Valve Guide, Perkins Diesel - Intake and exhaust. 152 CID and 203 CID perkins diesel engines. For tractor models 203, 205, 35, FE35, MF35, MF50, 200, 2244, 2200, 2500, MF235, 200B, 4500, MF230, 20C, 30B, MF245, MF250, 356, MF65, 300, 302, 304, 3165, MF165, 40B, 50. (Item #: 166914, Ref: 732445M1) $2.30

Valve, Intake - Intake valve, pin-type for 135, 202, 204, F40, MF135, MF35, MF50, MH50, TO30, TO35. Price is for EACH. MINIMUM ORDER IS 4. (Item #: 128687, Ref: 1750070M1) $8.20

Valve, Intake - Intake valve for 152 or 203 CID diesel standard bore 3.6 inch, injectors vertical in head. For 203, 205, 35, 356, FE35, MF35, MF50, MF65, Super 92. (Item #: 167112, Ref: 731151M1) $4.71