International Harvester / Farmall 424 Tractor Parts

[Categories]   [All Farmall Models]   [Print]  

Belts
Belt - Fan - For International / Farmall tractor models B275 (with increased capacity cooling), 424, 444, Replaces International OEM number 237153R1, 22/32" X 37.64", Thickness: .394", (Item #: 114727) $7.30

Brakes
Bonded Lined Brake Disc - This bonded lined brake disc fits the following tractor models: 354, 364, 384, 424, 444, 2300, 2424, 2444, 3414 (serial number 3516 and up), and 3444. It measures: 6 1/2 inches x 3 1/2 inches. It has 10 splines and a 1.62 inch spline diameter. It replaces part number 395161R1. Priced each disc. (Item #: 105450, Ref: 1975464C2) $12.60
Brake Actuator - This Brake Actuator is used with 6.5 inch discs. B414, 424, 444, 354, 364, 384, 3414, 2424, 2444. Replaces 3067135R91, 3105296R91, 3067135R92. (Item #: 105484, Ref: 3105296R91) $60.00
No Picture Brake Boot Dust Cover - Rubber. For tractor models 2300A, B414 after serial number 31374, 354, 364, 384, 424, 434, 444, 2424, 2444, 3414 after serial number 3515, 3444. (Item #: 127411, Ref: 3064173R1) $8.70
Disc Brake Actuating Spring - This Disc Brake Actuating Spring is 1.135 inch overall length, 0.825 inch outside diameter and 0.110 inch wire diameter. Fits models: B414, 2424, 2444, 354, 364, 384, 424, 434, 444; Replaces: 3066876R1. (Item #: 124547, Ref: C5NN2N320A) $2.00
Disc Brake Ball Bearing - Measuring 7/8 inches, this ball bearing is used in many disc brake systems. Typically 4 or 6 used per wheel. Replaces OEM numbers 09384AB, 150734A1, 16028R1, 166264, 16779X, 17028R1, 20063060, 2073622, 211-1028, 211-1328, 211-19, 211-221, 31-1750393, 33-0026328, 50A4272, 706039R1, 706039R2, 72073622, 7A2606, 0166264, 81716998, 81847078, 81866502, 82979987, 87554519, 87672308, 9170150, 920095936, 9959976, 9960587, BDB78, D5NN2N141A, E94FB9, E9NN2N324AA, E9NN2N324AB, GM145662, K963645, M830T, O9384AB (Item #: 126209, Ref: M830T) $3.00

Clutch
No Picture Clutch Alignment Tool - 1-1/8 inch 10 spline, 1-5/8 inch 10 spline, 3/4 inch pilot. For tractor models 364, 384, 385, 395, 494, 574, 584, 585, 595, 895, 995, 3230, 4210, 4220, 2400A, 2400B, (424, 2444 with single disc), 2500A, 2500B, 3500, 3500A. (Item #: 113942, Ref: S.70912) $18.40
No Picture Clutch Alignment Tool - 1-1/8 inch 10 spline, 1-3/4 inch 10 spline, 13/16 inch pilot. For tractor models 384, 414, 424, 444, 2300, 2300A, 2424, 2444. (Item #: 122047, Ref: S.70922) $27.10
Clutch Assembly, Dual - Contains Pressure Plate number 1539022C1, clutch disc number 1539025C1, PTO disc number 1539020C1. (Item #: 172511, Ref: 628135609) $1314.82
No Picture Clutch Disc - For International / Farmall tractor models 354, 364, 374, 384, 424, 434, 444, 2300, 2300A, 2424, 2444, Replaces Case IH OEM number 390010, (Item #: 166096) $130.00
Clutch Disc, Remanufactured, 392076R92 - For International / Farmall tractor models 424 (w/ Gas or Diesel Engine, s/n 10242 - earlier), 444 (All w/ Gas Engine), 2424 (s/n 2520 - earlier), 2444 (All w/ Gas Engine), 3444, Replaces International OEM number 392076R92, 392076HD6, Clutch Size: 11", Clutch Hub: 1-1/8", Clutch Spline: 10, Clutch Center: Spring, Clutch Type: 6 Reg Pads, For Single Clutch, (Item #: 205994) $157.15
Clutch Disc, Remanufactured, 392076R92, H392076 - For International / Farmall tractor models 424 (w/ Gas or Diesel Engine, s/n 10242 - earlier), 444 (All w/ Gas Engine), 2424 (s/n 2520 - earlier), 2444 (All w/ Gas Engine), 3444, Replaces International OEM number 392076R92, H392076, Clutch Size: 11", Clutch Hub: 1-1/8", Clutch Spline: 10, Clutch Center: Spring, Clutch Type: 4 Reg Pads, (Item #: 205995) $134.00
No Picture Clutch Flywheel Plate - For International / Farmall tractor models 424, 444, Compatible with International Construction and industrial models 2424, 2444, Replaces International OEM number 392498R1, (Item #: 173876) $105.52
Clutch Lever - Used In 390011R91 Dual Clutch Assembly. For tractor models 424, 444, 2424, 2444. (Item #: 173023, Ref: 392499R2) $15.90
Clutch Pressure Plate - Pressure Plate: 11 inch, with PTO disc, with 1.344 inch flywheel step (Auburn Design). For tractor models B414, 424, 434, 444, 2424, 2444. Replaces 399536R92. (Item #: 158382, Ref: 390011R92) $742.00
No Picture Clutch PTO Disc 9 Inch - For double clutch, 10 spline on 1.75 inch hub, organic, rigid. For tractor models 2300, 3414, 3444, B414, 345, 354, 364, 374, 384, 424, 444. (Item #: 163114, Ref: 1539020C1) $52.00
Clutch Shaft - For tractor models 2424, 2444, 384, 424, 444, B275, B414. Also replaces 751048R2. (Item #: 179948, Ref: 3071270R1) $20.10
No Picture Pressure Plate, Remanufactured - For International / Farmall tractor models 424, 444, 2424, 2444, 3444, Pressure Plate Size: 11", Pressure Plate Levers: 3, Pressure Plate Springs: 6, Pressure Plate Type: Single Stage, Additional Handling and Oversize Fees Apply To This Item, (Item #: 206068) $105.00
Pressure Plate, Remanufactured, 392077R91 - For International / Farmall tractor models 424 (s/n 10242 - earlier), 444, 2424 (s/n 2520 - earlier), 2444, Replaces International OEM number 392077R91, Pressure Plate Size: 11", Pressure Plate Levers: 3, Pressure Plate Springs: 3, Pressure Plate Type: Single Stage, (Item #: 203732) $81.00
PTO Clutch Disc, 9 Inch - PTO Clutch disc, organic, 9 inch, Heavy duty hub, (1.750 inch, 10 spline). For the following tractors: 345, 354, 364, 384, 424, B414. Industrial: 2300, 2444, 3414, 3444. (Item #: 113815, Ref: 1753753M94) $49.07
Release Bearing - Clutch release bearings, 3.500 inch outside diameter, 2.375 inch inside diameter, .730 inch wide bore. For tractor models 300, 330, 340, 350, 424, 444, 460 with standard clutch, 504, 606, 2424, 2444, 2504. For 1066, 140, 1466, 1468, 1566, 1568, 2400A, 2500A, 3088, 3288, 3388, 3588, 3688, 3788, 4166, 4186, 4366, 4386, 454, 464, 5088, 5288, 5488, 574, 666, 674, 686, 766, 966, Cub, Cub Lo-Boy, HYDRO 100, HYDRO 70, HYDRO 86. (Item #: 107995, Ref: 59879D) $31.70
No Picture Transmission Clutch Disc - For International / Farmall tractor models 424, 444, Compatible with International Construction and industrial models 2424, 2444, 3414, 3444, Replaces International OEM number 399536R92, Diameter: 11", Splines: 10, Spline Diameter: 1.125", Center: Spring loaded, Type: Organic, (Item #: 173881) $178.00

Cooling System
Fan Belt - This Fan Belt measures 36.562 inches length and 0.656 inch width. It is used on some B275, 424, 444 Tractors. Verify measurements before ordering. More than one size was used. Replaces International part number 237153R1 (Item #: 117363, Ref: 70209656) $13.80
Radiator Cap - 7 pound, fits short filler neck. For tractor models 100, 130, 140, 1410, 1412, 1440, 1460, (1640 serial number 44C0034705 and below), (1660 serial number JJC0038346 and below), (1680 serial number JJC0045689 and below), 1822, 1844, 200, 2022, 230, 240, 2400A, 2424, 2444, 2500A, 2504, 2606, 300, 330, 3388, 340, 350, 3588, 3788, 404, 4100, 4156, 4166, 424, 4366, 4386, 444, 450, 4568, 460, 464, 474, 4786, 504, 560, 606, 6388, 656, 6588, 660, 6788, 706, 806, 990, Hydro 84, Super H, Super M, Super MD, Super W4, Super W6, Super W9, Super WD6, Super WD9. (Item #: 112331, Ref: 180224M91) $6.60
Radiator Cap - 7 pound pressure radiator cap. Cap measures 2.328 inches diameter less finger tabs. Inside diameter is 2.215 and 1.970 inches between locking tabs. (** = FOR SHORT FILLER NECK). Fits **Super H, **Super M, MD, **Super W4, **Super W6 and WD6, **Super W9 and WD9, **100, **130, **140, **200, **230, 240, **300, **330, 340, **350, **400, 404, **424, **444, **450, **460, **504, **560, 606, **660, 2424, 2444, 2504, 2606, 4100, 4156, 4166. Replaces OEM 393229R91. (Item #: 112331, Ref: 180224M91) $6.60
Radiator Cap - For International / Farmall tractor models Hydro 70, Hydro 84, Hydro 86, 100, 130, 140 (s/n 13968-later), 200, 230, 240, 340, 404, 424, 444, 454, 464, 484, 504, 544, 574, 584, 606, 656, 664, 666, 674, 684, 686, 706, 756, 784, 806, 826, 856, 1026, 1206, 1256, 1456, Replaces International OEM number 532029R1, 393229R91, 402281R1, 378289R91, Pressurized, 1.5" Radiator neck I.D., (Item #: 112533) $22.00
Radiator/Fuel Tank Hold Down Spring - This spring is used for the Radiator and for the Fuel Tank. Total 5 used per tractor, 2 for the radiator and 3 for the fuel tank. Spring measures 3/4 of an inch diameter and 1.15 inches long. For tractor models H, HV, O4, O6, SUPER H, ( As radiator hold down spring only - 2 used: SUPER M, SUPER MTA, W4, W6, WD6, 400, 424, 450, 2424. (Item #: 126686, Ref: 48826D) $8.40
Radiator, Gas and Diesel - This radiator has a core height of 16 inches, width of 16 1/4 inches. It is 2 inches deep with 3 rows of tubes and 5 rows of fins per inch. The inlet is 2 3/8 inches and the outlet is 2 inches. It is copper and brass construction. replaces original part number 388458R91. Not for Europe built tractor. (Item #: 152350, Ref: 388458R91) $635.00
Radiator Hose - Bulk 3 x 1-3/8" - For International / Farmall tractor models H, OS4, Super H, Super W4, W4, 140, 200, 240, 274 (Diesel), 300, 340, 350, 404, 424 (Gas), 444, 2404, 2424 (Gas), 2444, Replaces Case IH OEM number 369092R2, 407002R1, 387721R1, I.D. (A): 1-3/8" (1.375"), O.D.: 1-3/4" (1.750"), Length: 3', For Hose Clamp use Item #: 130453, (Item #: 114083) $22.40
Radiator Hose - Lower - For International / Farmall tractor models A (s/n 355669-earlier), B, Super A, 140, 240, 404, 424 (gas), 444 (gas), Replaces International OEM number 20075DB, 2" ID, For Hose Clamp use Item #: 130455, (Item #: 112337) $4.30
No Picture Radiator Hose, Lower - Inside diameter is 1.437 inches. For tractor models 424 gas and diesel, 444 diesel. (Item #: 114726, Ref: 388463R1) $6.70
Radiator Hose Upper - Measures 1.5 inches inside diameter. For 424, 444. (Item #: 114725, Ref: 388464R1) $15.20
Radiator Hose, Upper - Measures 2.00 inches inside diameter on one end and 2.625 inside diameter on the other, for gas engines. For tractor models 140, 240, 404, 424, 444. (Item #: 117695, Ref: 369397R1) $15.70
Tower Hose Clamp 2.350" to 2.765" - For International / Farmall tractor models 140, 240, 404, 424 (Gas), 444 (Gas) Replaces International OEM number 45813D, , Compatible with John Deere tractor models 1010, 1020, 1520, 1530, 2010, 2020, 2030, 2510, 2520, 2630, 3010, 3020, 4000, 4010, 4020, 4025, 4030, 4230, 4320, 4430, 4520, 4620, 4630, 5010, 5020, 6030, 7020, 7520, 8020, 8430, 8630, (Item #: 130442) $7.70
Water Pump - This water pump comes with hub and gasket for tractor models 140, (200, 230, IH 240 serial number 65001 and up with C123 engine), (330, 340, 404 with C135 engine), 2400, 2404, 2424, 2444, 4000, 444, all with C123 serial number 65001 and up, C135, C146 or 153 Gas engines. Replaces 367683R91, 375793R91, 367686R91, 367683R91. (Item #: 113376, Ref: 375793R92) $66.00
Water Pump Gasket - Used on 200, 230, 240, 2404 Indust/Const, 2424 Indust/Const, 2444 Indust/Const, 2504 Indust/Const, 330, 340, 404, 424, 444, 504. Replaces 367687R2 (Item #: 153405, Ref: 367687R2) $1.80
Water Pump Pulley Flange - For International / Farmall tractor models B250, B275, B276, B414, TD5, 274, 276, 354, 364, 384, 424, 434, 444, 2300A, 2424, 3444, Compatible with International Construction and industrial models 2424, 3414, 3444, Compatible with International Engine (s) BC144, BD144, BD154, Replaces International OEM number 703825R11, Adjustable Flange Half, Use with Water Pump Item No. 100019 (703820R94), O.D. at one end: 0.875", O.D. at opposite end: 0.998", 5.397" total length, (Item #: 115090) $15.70
Water Pump - Without Bypass - New with gasket and with 10mm Double Groove Pulley. For tractor models 2300A, 354, BC144, 364, B414, 424, 434, 444, B250, B275, B276, all with BD154 diesel or BC144 gas engines. This water pump replaces casting numbers 703820N, 704216. Also replaces original part numbers 3119778R92, 703820R94, 703820R97. (Item #: 100019, Ref: 703820R95) $54.00

Decals and Emblems
Chassis Decal Set - Vinyl - International Chassis Decal Set - Vinyl Die Cut. DOES NOT INCLUDE HOOD SET. For tractor models: 424, 444 US Built, 544, 656, 686, HYDRO 70, HYDRO 84. (Item #: 183256, Ref: R0548V) $68.00
No Picture Decal Set - For 424 Gas. Hood only Decal Set. (Item #: 183229, Ref: R2631) $60.00
No Picture Decal Set - For 424 Diesel. Hood Only Decal Set. (Item #: 183227, Ref: R4230) $60.00
Front Emblem - Plastic "IH", red, black and white, 3-3/4 inch x 2-3/4 inch. For tractor models Cub Lo-Boy, 154, 184, 185, 140, 276, 404, 424, 434, 444, 504, 544, 553, 606, 654, 656, 666, 686, 706, 724, 756, 766, 786, 806, 824, 856, 886, 966, 986, 1066, 1086, 1206, 1256, 1466, 1468, 1486, 1586, 2400, 2404, 2424, 2444, 2500, 2504, 2544, 2606, 2656, 2706, 2756, 2806, 2856, 4156, 21206, 21256, Hydro 70, Hydro 86. (Item #: 108481, Ref: 2751846R1) $19.10
Grille Emblem - For International / Farmall tractor models Cub (184), Hydro 70, Hydro 86, Hydro 100, Hydro 186, 140, 240, 340, 404, 424, 444, 544, 606, 666, 686, 766, 786, 886, 966, 986, 1066, 1086, 1466, 1468, 1486, 1566, 1568, 1586, 2400A, 2500A, Replaces International OEM number 368523R4, Height:3-3/8", Made of die cast metal, (Item #: 108482) $51.00
IH Decal, 1-5/8", Vinyl - For International / Farmall tractor models A, B, C, Cub, H, Hydro 70, Hydro 84, Hydro 186, I4, I6, I9, M, O4, O6, Super A, Super C, Super H, Super M, Super MTA, Super W4, Super W6, Super W9, W4, W6, W9, 100, 130, 140, 200, 230, 240, 274, 284, 300, 330, 340, 350, 354, 400, 404, 424, 444, 450, 454, 460, 464, 504, 544, 560, IH logo vinyl cut decal 1 5/8", no background, (Item #: 101024) $2.80
IH Decal, 1", Vinyl - For International / Farmall tractor models A, B, C, Cub, H, Hydro 70, Hydro 84, Hydro 186, I4, I6, I9, M, O4, O6, Super A, Super C, Super H, Super M, Super MTA, Super W4, Super W6, Super W9, W4, W6, W9, 100, 130, 140, 200, 230, 240, 274, 284, 300, 330, 340, 350, 354, 400, 404, 424, 444, 450, 454, 460, 464, 504, 544, 560, IH logo vinyl cut decal 1", no background, (Item #: 101023) $1.90
IH Decal, 3" x 3-1/2", Vinyl - For International / Farmall tractor models A, B, C, Cub, H, Hydro 70, Hydro 84, Hydro 186, I4, I6, I9, M, O4, O6, Super A, Super C, Super H, Super M, Super MTA, Super W4, Super W6, Super W9, W4, W6, W9, 100, 130, 140, 200, 230, 240, 274, 284, 300, 330, 340, 350, 354, 400, 404, 424, 444, 450, 454, 460, 464, 504, 544, 560, IH logo vinyl cut decal 3" x 3-1/2", No background, (Item #: 101025) $11.10
IH Decal, 4-1/2" x 5" - For International / Farmall tractor models A, B, C, Cub, H, Hydro 70, Hydro 84, Hydro 186, I4, I6, I9, M, O4, O6, Super A, Super C, Super H, Super M, Super MTA, Super W4, Super W6, Super W9, W4, W6, W9, 100, 130, 140, 200, 230, 240, 274, 284, 300, 330, 340, 350, 354, 400, 404, 424, 444, 450, 454, 460, 464, 504, 544, 560, IH logo 4-1/2" x 5", Mylar decal, (Item #: 101095) $5.60
International 424 Decal Set, Vinyl - For International / Farmall tractor model 424, Hoods and model letters, (Item #: 100973) $62.00
International 424 Diesel Decal Set, Vinyl - For International / Farmall tractor model 424, Diesel hoods and model letters, (Item #: 100974) $62.00
International Decal, 17", Mylar - For International / Farmall tractor models A, B, C, Cub, H, Hydro 70, Hydro 84, Hydro 186, I4, I6, I9, M, O4, O6, Super A, Super C, Super H, Super M, Super MTA, Super W4, Super W6, Super W9, W4, W6, W9, 100, 130, 140, 200, 230, 240, 274, 284, 300, 330, 340, 350, 354, 400, 404, 424, 444, 450, 454, 460, 464, 504, 544, 560, 17" long, Black, Mylar decal, (Item #: 101105) $5.60
International Decal, 8-1/2", Mylar - For International / Farmall tractor models A, B, C, Cub, H, Hydro 70, Hydro 84, Hydro 186, I4, I6, I9, M, O4, O6, Super A, Super C, Super H, Super M, Super MTA, Super W4, Super W6, Super W9, W4, W6, W9, 100, 130, 140, 200, 230, 240, 274, 284, 300, 330, 340, 350, 354, 400, 404, 424, 444, 450, 454, 460, 464, 504, 544, 560, 8 1/2" long, Black, Mylar decal, (Item #: 101104) $3.70
International Decal Set,10" IH Logo, Vinyl - For International / Farmall tractor models A, B, C, Cub, H, Hydro 70, Hydro 84, Hydro 186, I4, I6, I9, M, O4, O6, Super A, Super C, Super H, Super M, Super MTA, Super W4, Super W6, Super W9, W4, W6, W9, 100, 130, 140, 200, 230, 240, 274, 284, 300, 330, 340, 350, 354, 400, 404, 424, 444, 450, 454, 460, 464, 504, 544, 560, IH logo vinyl cut decal 10", (Item #: 101022) $29.60
International Decal Set, 1 1/4" IH Logo, Vinyl - For International / Farmall tractor models A, B, C, Cub, H, Hydro 70, Hydro 84, Hydro 186, I4, I6, I9, M, O4, O6, Super A, Super C, Super H, Super M, Super MTA, Super W4, Super W6, Super W9, W4, W6, W9, 100, 130, 140, 200, 230, 240, 274, 284, 300, 330, 340, 350, 354, 400, 404, 424, 444, 450, 454, 460, 464, 504, 544, 560, IH logo vinyl cut decal 1-1/4", (Item #: 101018) $2.80
International Decal Set, 1 3/4"x 1 5/8" IH Logo, Vinyl - For International / Farmall tractor models A, B, C, Cub, H, Hydro 70, Hydro 84, Hydro 186, I4, I6, I9, M, O4, O6, Super A, Super C, Super H, Super M, Super MTA, Super W4, Super W6, Super W9, W4, W6, W9, 100, 130, 140, 200, 230, 240, 274, 284, 300, 330, 340, 350, 354, 400, 404, 424, 444, 450, 454, 460, 464, 504, 544, 560, IH logo vinyl cut decal 1-3/4", (Item #: 101019) $3.70
No Picture International Decal Set, 6 1/2"x 7" Shaded IH Logo, Vinyl - For International / Farmall tractor models A, B, C, Cub, H, Hydro 70, Hydro 84, Hydro 186, I4, I6, I9, M, O4, O6, Super A, Super C, Super H, Super M, Super MTA, Super W4, Super W6, Super W9, W4, W6, W9, 100, 130, 140, 200, 230, 240, 274, 284, 300, 330, 340, 350, 354, 400, 404, 424, 444, 450, 454, 460, 464, 504, 544, 560, IH Logo 7", Vinyl Cut, Shaded Outline, (Item #: 101020) $16.70
No Picture International Decal Set, 7 1/4"x 8" Shaded IH Logo, Vinyl - For International / Farmall tractor models A, B, C, Cub, H, Hydro 70, Hydro 84, Hydro 186, I4, I6, I9, M, O4, O6, Super A, Super C, Super H, Super M, Super MTA, Super W4, Super W6, Super W9, W4, W6, W9, 100, 130, 140, 200, 230, 240, 274, 284, 300, 330, 340, 350, 354, 400, 404, 424, 444, 450, 454, 460, 464, 504, 544, 560, IH logo vinyl cut decal 8", (Item #: 101021) $22.20
International Harvester Decal, 2-3/4" x 3" - For International / Farmall tractor models A, B, C, Cub, H, Hydro 70, Hydro 84, Hydro 186, I4, I6, I9, M, O4, O6, Super A, Super C, Super H, Super M, Super MTA, Super W4, Super W6, Super W9, W4, W6, W9, 100, 130, 140, 200, 230, 240, 274, 284, 300, 330, 340, 350, 354, 400, 404, 424, 444, 450, 454, 460, 464, 504, 544, 560, (Item #: 101093) $3.70
International Harvester Decal, 2" x 2-1/2", Mylar - For International / Farmall tractor models A, B, C, Cub, H, Hydro 70, Hydro 84, Hydro 186, I4, I6, I9, M, O4, O6, Super A, Super C, Super H, Super M, Super MTA, Super W4, Super W6, Super W9, W4, W6, W9, 100, 130, 140, 200, 230, 240, 274, 284, 300, 330, 340, 350, 354, 400, 404, 424, 444, 450, 454, 460, 464, 504, 544, 560, IH logo 2" x 2-1/2", No background, Mylar decal, (Item #: 101097) $3.70
International Harvester Decal, 2" x 2-1/4", Mylar - For International / Farmall tractor models A, B, C, Cub, H, Hydro 70, Hydro 84, Hydro 186, I4, I6, I9, M, O4, O6, Super A, Super C, Super H, Super M, Super MTA, Super W4, Super W6, Super W9, W4, W6, W9, 100, 130, 140, 200, 230, 240, 274, 284, 300, 330, 340, 350, 354, 400, 404, 424, 444, 450, 454, 460, 464, 504, 544, 560, IH logo 2" x 2-1/4", Mylar decal, (Item #: 101092) $3.70
International Harvester Decal, 5-1/2" x 6", Mylar - For International / Farmall tractor models A, B, C, Cub, H, Hydro 70, Hydro 84, Hydro 186, I4, I6, I9, M, O4, O6, Super A, Super C, Super H, Super M, Super MTA, Super W4, Super W6, Super W9, W4, W6, W9, 100, 130, 140, 200, 230, 240, 274, 284, 300, 330, 340, 350, 354, 400, 404, 424, 444, 450, 454, 460, 464, 504, 544, 560, IH logo 5-1/2" x 6", Mylar decal, (Item #: 101096) $5.60
International Harvester Decal, 5-1/2" x 6", Mylar - For International / Farmall tractor models A, B, C, Cub, H, Hydro 70, Hydro 84, Hydro 186, I4, I6, I9, M, O4, O6, Super A, Super C, Super H, Super M, Super MTA, Super W4, Super W6, Super W9, W4, W6, W9, 100, 130, 140, 200, 230, 240, 274, 284, 300, 330, 340, 350, 354, 400, 404, 424, 444, 450, 454, 460, 464, 504, 544, 560, IH logo 5-1/2" x 6", No background, Mylar decal, (Item #: 101098) $5.60
International Harvester Decal, 5" Mylar - For International / Farmall tractor models A, B, C, Cub, H, Hydro 70, Hydro 84, Hydro 186, I4, I6, I9, M, O4, O6, Super A, Super C, Super H, Super M, Super MTA, Super W4, Super W6, Super W9, W4, W6, W9, 100, 130, 140, 200, 230, 240, 274, 284, 300, 330, 340, 350, 354, 400, 404, 424, 444, 450, 454, 460, 464, 504, 544, 560, IH Logo decal, 5" diameter, Shaded outline, Mylar decal, (Item #: 101099) $5.60
International Harvester Decal, 6" Mylar - For International / Farmall tractor models A, B, C, Cub, H, Hydro 70, Hydro 84, Hydro 186, I4, I6, I9, M, O4, O6, Super A, Super C, Super H, Super M, Super MTA, Super W4, Super W6, Super W9, W4, W6, W9, 100, 130, 140, 200, 230, 240, 274, 284, 300, 330, 340, 350, 354, 400, 404, 424, 444, 450, 454, 460, 464, 504, 544, 560, IH Logo decal, 6" diameter, Shaded outline, Mylar decal, (Item #: 101100) $7.40
International Harvester Decal, 7-1/2", Mylar - For International / Farmall tractor models A, B, C, Cub, H, Hydro 70, Hydro 84, Hydro 186, I4, I6, I9, M, O4, O6, Super A, Super C, Super H, Super M, Super MTA, Super W4, Super W6, Super W9, W4, W6, W9, 100, 130, 140, 200, 230, 240, 274, 284, 300, 330, 340, 350, 354, 400, 404, 424, 444, 450, 454, 460, 464, 504, 544, 560, IH Logo decal, 7 1/2" diameter, Shaded outline, Mylar decal, (Item #: 101101) $9.30
International Harvester Decal, 9", Mylar - For International / Farmall tractor models A, B, C, Cub, H, Hydro 70, Hydro 84, Hydro 186, I4, I6, I9, M, O4, O6, Super A, Super C, Super H, Super M, Super MTA, Super W4, Super W6, Super W9, W4, W6, W9, 100, 130, 140, 200, 230, 240, 274, 284, 300, 330, 340, 350, 354, 400, 404, 424, 444, 450, 454, 460, 464, 504, 544, 560, IH Logo decal, 9" diameter, Shaded outline, Mylar decal, (Item #: 101102) $11.10
International Hood Decal, 23-1/2", Vinyl - For International / Farmall tractor models A, B, C, Cub, H, Hydro 70, Hydro 84, Hydro 186, I4, I6, I9, M, O4, O6, Super A, Super C, Super H, Super M, Super MTA, Super W4, Super W6, Super W9, W4, W6, W9, 100, 130, 140, 200, 230, 240, 274, 284, 300, 330, 340, 350, 354, 400, 404, 424, 444, 450, 454, 460, 464, 504, 544, 560, Size: 23-1/2", Black lettering, (Item #: 101031) $14.80
McCormick International Decal, 10" Vinyl - For International / Farmall tractor models A, B, C, Cub, H, Hydro 70, Hydro 84, Hydro 186, I4, I6, I9, M, O4, O6, Super A, Super C, Super H, Super M, Super MTA, Super W4, Super W6, Super W9, W4, W6, W9, 100, 130, 140, 200, 230, 240, 274, 284, 300, 330, 340, 350, 354, 400, 404, 424, 444, 450, 454, 460, 464, 504, 544, 560, 10" long, Black and white, Vinyl decal, (Item #: 101103) $9.30
McCormick International Decal, Hood, White/Black, 7-1/4", Vinyl - For International / Farmall tractor models A, B, C, Cub, H, Hydro 70, Hydro 84, Hydro 186, I4, I6, I9, M, O4, O6, Super A, Super C, Super H, Super M, Super MTA, Super W4, Super W6, Super W9, W4, W6, W9, 100, 130, 140, 200, 230, 240, 274, 284, 300, 330, 340, 350, 354, 400, 404, 424, 444, 450, 454, 460, 464, 504, 544, 560, 7-1/4" black and white, Vinyl decal, (Item #: 101026) $7.40

Drive Train
Bull Pinion Cage - This Pull Pinion Shaft Cage is right side. It is used on CASE-IH B414, 424, 444, 354, 364, 384, 3414, 2424, 2444. Replaces 3064164R11, 3072916R11, 3071402R11 (Item #: 179381, Ref: 3071402R11) $162.00
Clutch Shaft - For tractor models 2424, 2444, 384, 424, 444, B275, B414. Also replaces 751048R2. (Item #: 179948, Ref: 3071270R1) $20.10
Gear Shift Boot - Some of the Farmall / International tractors were not factory equipped with a gear shift boot, and it was sold as an extra. This boot is used on models: H, M, 560, I4, I6, ID6, Super MVTA, 2606, HV, MD, T340, T5, MDV, MV, TD6, O4, O6, ODS6, OS4, OS6, Super H, Super HV, Super M, Super MD, Super MDV, Super MTA, Super MTA, Super MV, Super W4, Super W6, Super WD6, W4, W6, WD6, 300, 330, 340, 350, 400, 404, 424, 444, 450, 460, 504, 606, 660, B275, 354, 384. It measures 4-3/4 inches tall, 11/16 inch top hole inside diameter and 2-3/4 inches bottom hole. (Item #: 182890, Ref: 64603DA) $25.90
Gear Shift Knob - For Cub, Cub Lo-Boy, A, Super A, Super AV, B, C, Super C, H, HV, Super H, Super HV, M, MD, Super M, Super MTA, W4, W6, WD6, Super W6, W9, WD9, Super WD9, 100, 130, 140, 200, 230, 240, 300, 330, 340, 350, 354, 400, 404, 450, 424, 460, 504, 560, 600, 606, 660, and on the hydraulic lever control on the 454 and 574. Gear shift lever knob. Replaces 3121549R1, IHS266. (Item #: 109514, Ref: 53717DA) $5.90
Hi / Low Range Shift Lever Seal - This hi / low range shift lever seal has a .625 inch Inside Diameter, a 1.128 inch Outside Diameter and is .25 inch wide. It Fits: 2300A, 2424, 2444, 3414, 3444, 354, 364, 384, 424, 434, 444, 7000, B-275, B-276, B-414. Replaces: 132707R91, 23676D, 3069986R91, 353183R91, 353183R92, 353183R93, 381369R91, 385038R91, 721-3011, 751086R91, 751087R91, 921-3011, 471466 (Item #: 178140, Ref: A26778) $7.80
Oil Seal - Fits: [A, A-I, A1, AV, AV-1, B, BN, C, Super A, Super A-1, Super AV, Super AV-1, Super C, 100, 130, 140, 200, 230, 240, 2404, 404 (Top Transmission Shaft Front Seal)], [B-250, B-275, B-276, B-414, 2300, 2300A, 2424, 2444, 3414, 3444, 354, 364, 384, 424, 434, 444 (Bull Pinion Shaft Bearing Retainer Seal)], [Cub, Cub Lo-Boy, 154, 184, 185 (Final Drive Upper Pinion Shaft Seal)], [M, MD, MDV, MV (Transmission Counter Shaft Front Seal)], MTA (Front Wheel Seal; with single front 900 x 10 wheel), [O4, OS4 (PTO Output Shaft Seal; serial number 2159 to 9300)], [Super M, Super MD, Super MDV, Super MV (Transmission Counter Shaft Front Seal; up to serial number F52627 and up to seril number L51241)], W4 (PTO Output Shaft Seal; serial number 786 to 9300). Replaces: 21969D, 264694R91, 287440R91, 3043788R91, 3043788R92, 358765R91, 358784R91, 358808R91, 358823R91, 381907R91, 42177D, 43278D, 50839D, 530969R91, 703907R91, 703908R92, A29424. (Item #: 178204, Ref: 381907R91) $6.00
Shift Lever Repair Pin Kit - For International / Farmall tractor models B250, B275, B276, B414, H, HV, I4, I6, I9, M, MD, MTA, O4, O6, OS6, Super H, Super HV, Super M, Super MTA, Super W6, W4, W6, W400, W450, WD6, WD9, 300, 330, 340, 350, 354, 364, 384, 400, 424, 434, 444, 450, 460, 504, 560, 606, 660, 2300, Replaces International OEM number 256918R1, 172529, 256919R1, 259918R11, 310662R11, 310664R11, 34878D, 357003R1, 40465DA, 40466DA, 705650R1, (Item #: 167881) $25.00
Transmission Coupling - For tractor models 2424, 2444, 384, 424, 444. (Item #: 751076R3) $69.44
Transmission Drive Shaft Seal - Drive Shaft Seal for tractor models 2424, 2444, 384, 424, 444, B275, B414. Also replaces 751080R93. (Item #: 178578, Ref: 751080R91) $15.30
Transmission Gear - 2nd and 3rd gear for tractor models 2424, 2444, 384, 424, 444, B275, B414. (Item #: 182672, Ref: 751071R1) $142.00
Transmission Gear - 4th and Direct. For tractor models 2424, 2444, 384, 424, 444, B275, B414. Replaces 751073R1 (Item #: 178391, Ref: 751073R1) $53.00
Transmission Gear - 4th and Direct gear (31 teeth) for tractor models 2424, 2444, 384, 424, 444, B275, B414. (Item #: 178390, Ref: 751072R1) $80.00
Transmission Gear - 2nd Gear for models: 2424, 2444, 384, 424, 444, B275, B414 (Item #: 182677, Ref: 751054R1) $97.00
Transmission Gear - Reverse Shaft and Gear for models: 2444, 354, 364, 384, 424, 444. Replaces International OEM nos 3071849R2, 3071849R1. Overall Length: 5.160", Out Side Diameter at Oil Grooves: .989", Out Side Diameter at Splines: 1.143", Out Side Diameter at Lower Shaft: 1.260", Out Side Diameter at Gear: 3.140", Splines: 26, Gear Teeth: 20 (Item #: 134303, Ref: 3071849R2) $72.00
Transmission Gear - 3rd and 4th Gear for models: 2424, 2444, 384, 424, 444, B414 (Item #: 179627, Ref: 751055R3) $128.00
Transmission Gear Kit - Ring and Pinion for tractor models B414, 424, 444, 354, 364, 384, 3414, 2424, 2444. (Item #: 3069966R91) $270.30

Electrical System
Distributor - Original IHC design comes with a 32 tooth drive gear. For tractor models Super W6TA, Super W9, Super WD6, Super WD6-TA, Super WD9, Super WDR9, W4, W400, W450, W6, W9, WD6, WD9, WDR9, WR9, 100, 130, 140, 200, 230, 240, 300, 330, 340, 350, 400, 404, 424, 444, 450, 454, 504, 600, 650, 2400A, 2400B, 2404, 2405B, 2410B, 2412B, 2424, 2444, 2500A, 2500B, 2504, 3514. R6332. MHSK1 (Item #: 124839, Ref: 107304C91) $120.00
Distributor - New and complete distributor comes with a 32 tooth gear, and is for tractor models: A, AV, B, BN, C, H, HV, M, MV, Super A, Super AV, Super C, Super H, Super M, Super MTA and other IH equipment with International Distributors. Replaces: 107296C91, 107299C91, 107302C91, 107304C91, 353890R91, Distributor Housing Casting Number: 353898R11, 354900R91, 357935R91, 362473R91, 362722R91, 364653R91, 364696R92, 366928R91, 372712R91, 380622R91. Uses IH points (included). (Item #: 124839, Ref: 107304C91) $120.00
Distributor Cap Spring Clip - Fits listed IH models when equipped with IH brand distributor 353898R11. Replaces: 107384C1, 353894R1 (Item #: 178117, Ref: 353894R1) $16.80
Distributor Drive Housing - This is a new distributor drive housing with an opening for tachometer drive. It is used to change from a magneto to a distributor or to add a tachometer drive to your tractor. The tachometer drive parts (tachometer drive assembly part number 369695R1, tachometer cable connector housing part number 369692R1 and 363817R1, connection housing plate) or tach. Drive blockoff plate are sold separately. NOTE: Will also work on tractors without tach drive by ordering number 363764R1 block off plate. Use with 107304C91 distributor when replacing a magneto. fits tractor models A, A1, AV, AV-1, B, BN, C, Cub, Cub Lo-Boy, H, HV, I4, I6, I9, M, MTA, MV, O4, O6, OS4, OS6, Super A, Super AV, Super C, Super H, Super HV, Super M, Super MTA, Super MV, Super MVTA, Super W4, Super W6, Super W9, W4, W6, W6TA, WR9S, 100, 130, 140, 154, 184, 185, 200, 230, 240, 2404, 2424, 2444, 2504, 300, 330, 340, 3444, 350, 3514, 404, 424, 444, 504, 400, 600, 650 450. Replaces: 363749R91, 363763R11. (Item #: 178938, Ref: 363749R91) $108.00
Distributor Drive Housing, Used - For International tractor models C, M, MD, MTA, Super A, Super C, 200, 230, 240, 300, 330, 340, 350, 400, 424, 450, 504, 2404, 2424, 2504, Replaces International OEM number 363763R11, With Tachometer Drive Hole, For a new version of this item use Item #: 178938, Used items are not always in stock. If we are unable to ship this part we will contact you within one business day., (Item #: 429775) $65.01
Distributor Dust Cover - Used with horizontal IHC distributor 353898R11 or J4 magneto on Models: 424, 444, 450, W450, 460, 504, 560, 600, 606, 650, 656, 660, 706, 756, 806, 826, 856, 3514, 3616. Replaces 384831R91. (Item #: 107074, Ref: 353900R11) $16.10
Distributor Gear - This Distributor Gear has 32 teeth. It is used on IH Distributor 353898R11. Replaces original part numbers 353902R1, 531461R91 (Item #: 111179, Ref: 353902R1) $29.00
Distributor Hold Down Clamp - For 5/16 inch hold down bolt and IH built distributor. 2 used per engine, sold individually. Fits fits tractor models A, AV, B, BN, C, Cub, Cub Lo-Boy, H, HV, Hydro 70, Hydro 86, I4, I6, I9, ID6, ID9, M, MV, O4, O6, OS4, OS6, Super A, Super A-1, Super AV, Super AV-1, Super C, Super H, Super HV, Super M, Super MTA, Super MV, Super MVTA, Super W4, Super W6, Super W6TA, Super W9, W4, W6, W9, WR9S, 100, 130, 140, 154, 184, 185, 200, 230, 240, 2400A, 2400B, 2404, 2405B, 2410B, 2412B, 2424, 2444, 2500A, 2500B, 2504, 2505B, 2510B, 2514B, 2544, 2606, 2656, 2706, 2756, 2806, 2826, 2856, 300, 330, 340, 350, 400, 404, 424, 444, 450, 454, 460, 464, 504, 544, 560, 574, 600, 606, 650, 656, 660, 666, 674, 686, 706, 756, 766, 806, 826, 856. All with IH distributors. Replaces 341139R1, 353937R1. (Item #: 182464, Ref: 341139R1) $8.90
Distributor Rotor - For IH Distributors on models: 100, 130, 140, 200, 230, 240, 300, 330, 340, 350, 4, 400, 404, 424, 444, 450, 6, A, AV, B, BN, C, H, HV, M, Super AV, Super C, Super H, Super HV, Super M, Super MTA, Super W4, Super W6, Super W6TA, Super A, Cub, Cub Lo-boy, Cub 154-Lo-boy, Cub 185-Lo-boy. NOT FOR USE ON EARLY MODELS WITH A MAGNETO. (Item #: 110266, Ref: 353896R1) $4.50
Distributor Tach Drive Housing Block Off Plate - This new Distributor Tachometer Drive Housing Block Off Plate with Gasket is used with part number 363749R91 when a Tachometer is not used. Fits tractor models Cub, Cub Lo-Boy, 130, 140, 230, 240, 2404, 300, 330, 400, 404, 450, 600, 650, 2424, 2444, 340, 424, 444, 2504, 350, 504. Replaces 363764R1, 363765R1. (Item #: 150708, Ref: 363764R1) $9.30
Distributor with base and tach drive, Remanufactured - For International / Farmall tractor models A, B, C, Cub, H, M, Super A, Super C, Super H, Super M, W4, W6, W9, 100, 130, 140, 200, 230, 240, 300, 330, 340, 350, 400, 404, 424, 444, 450, 504, 600, 650, 2424, 2504, With tachometer drive and with base, Includes new distributor cap, points, condenser, 6V coil, and all other parts needed for a thorough rebuilt unit, (Item #: 203589) $350.01
Distributor with base less tach drive, Remanufactured - For International / Farmall tractor models A, B, C, Cub, H, HV, I4, I6, M, MTA, O4, O6, OS4, OS6, Super A, Super C, Super H, Super M, Super MTA, Super W4, Super W6, W4, W6, W9, 100, 130, 140, 200, 230, 240, 300, 330, 340, 350, 400, 404, 424, 444, 450, 504, 600, 650, 2404, 2424, 2444, 2504, 3444, 3514, Compatible with International Combine (s) 105, 203, Compatible with International Construction and industrial models T6, T340, 500, Without tachometer drive and with base, Includes new distributor cap, points, condenser, 6V Coil, and all other parts needed for a thorough rebuilt unit, (Item #: 203588) $235.01
Electronic Ignition Conversion Kit - Pertronix Electronic Ignition Module Replaces Points and Condenser. Use on tractors with 6 volt POSITIVE ground system only. Use with distributor 353898R1 or 357935R91 on: Cub, Cub Lo-Boy, Cub 154 Lo-Boy, 184, Cub 185 Lo-Boy, A, AV, Super A, Super AV, BN, C, Super C, H, HV, Super H, Super HV, M, MV, Super M, Super MTA, Super MD, Super MDV, 100, 130, 140, 200, 230, 240, 300, 330, 340, 350, 400, 404, 424, 444, 454, 504, 600, 650 (Item #: 105084, Ref: 1442P6) $195.00
Electronic Ignition Conversion Kit - 12V Negative Ground - Pertronix Electronic Ignition Module Replaces Points and Condenser. Use on tractors with 12 volt NEGATIVE ground system only. Use with IH distributor 353898R1 or 357935R91 on: Cub, Cub Lo-Boy, Cub 154 Lo-Boy, 184, Cub 185 Lo-Boy, A, AV, Super A, Super AV, BN, C, Super C, H, HV, Super H, Super HV, M, MV, Super M, Super MTA, Super MD, Super MDV, 100, 130, 140, 200, 230, 240, 300, 330, 340, 350, 400, 404, 424, 444, 454, 504, 600, 650. Verify distributor number before ordering. (Item #: 105083, Ref: 1442) $164.00
Fuse Holder Kit - For Cub, Cub Lo-Boy, Hydro 70, Hydro 86, Hydro 100, 140, 404, 424, 444, 454, 464, 504, 574, 606, 656, 666, 674, 686, 706, 756, 766, 826, 856, 966, 1026, 1066, 1206, 1256, 1456, 1466, 1468, 1566, 1568, 2400A, 2404, 2424, 2444, 4500A, 2504, 2544, 2606, 2656, 2706, 2756, 2826, 2856, 4100, 4156, 4166, 4186, 4366, 4386, 4568, 4586, 1500, 21026, 21206, 21256, 21456. Replacement Fuse Holder Kit. Mounts on 5/8 inch diameter hole in instrument panel. 2 spade connectors. (Item #: 112273, Ref: 376852R91) $10.90
Fuse Housing - Reproduction of original Fuse Housing. Comes as pictured. For tractor models (Super A, Super AV, A1 all with magneto), C, Super C, 200, (H late with regulator under tank), Super H, HV, (M with regulator on post), (Super M 1953-1954), (Super M diesel), Super MTA, W4, OS4, O4, 100, 130, 400, 450. Replaces: 365515R91, 376852R91, 354232R91 (Item #: 112273, Ref: 376852R91) $10.90
Generator - Delco Style, Remanufactured - This is a Delco Style 9919, 12 volt, 20 amp remanufactured generator. It replaces Delco 1100399, 1100418, 1100422, 1100449. Replaces 9919, 340-33, 340-33A, 92-01-3100. Add $25.00 core charge to price - you will receive instructions for returning your core for a refund if you have one available. (Item #: 203521) $381.10
Generator, Delco Type, 12 Volt - For tractor models 140, 214, 220, 37, 404, 420, 424, 450, 460, 504, 560, 600, 606, 660, 700, 770, 780, 806, 2404, 2424, 2504, 2606, Cub, Lo-Boy, T6, TD6, TD9, Power Unit. Replaces Delco numbers 1100305, 1100335, 1100363, 1100364, 1100369, 1100394, 1100401, 1100409, 1100426, 1100424. Remanufactured. Refundable $25.00 core charge will be added to your order. (Item #: 203181, Ref: TG-59) $370.72
Glow Plug Resistor Indicator - This Glow Plug Resistor Indicator is for tractor models B250, 274, 275, 354, 414, 424, 434, 444, 2300, 2444. Replaces 703557R92, 706685R92, 3042230R91 (Item #: 168898, Ref: 3042230R91) $20.70
Key Switch, 2 Terminal - With keys. For tractor models (Cub serial number 224401 to 239826 with battery ignition), (Cub Lo-Boy from serial number 18701 and up with battery ignition), Cub Cadet 100, 100, (140 serial number 26801 to 45000), 240, 330, 340, 350, 404, 2404, 424, 2424, 444, 2444, 450, W450, 460, 504, 544, 560, 606, 650, 656, 600, 664, 666, 686, 706, 756, 766, 806, 826, 856, 966, 1026, 1066, 1206, 1256, 1456, 1466, 1468, 1566, 1568, Hydro 70, Hydro 86, Hydro 100. Replaces 370375R91, 379594R92, 403562R2. (Item #: 113393, Ref: 366313R91) $14.00
Spark Plug - Spark Plug 18MM Thread Diameter for: 100, 130, 140, 200, 230, 240, 300, 330, 340, 350, 400, 404, 424, 444, 450, 460, A, AV, B, BN, C, H, HV, M, Super AV, Super C, Super H, Super HV, Super M, Super MTA, Super W4, Super W6, Super W6TA, Super A, Cub, Cub Lo-boy, Cub 154-Lo-boy, Cub 185-Lo-boy. Replaces OEM number 360942R1. Also replaces Autolite AL386, AL388, AL3116 and Champion D16, 516, D10, D14, D16J, D21, D89D, K13, K15J, M14, RD14, RD16, UD16 plugs (Item #: 111742, Ref: AL386) $3.20
Spark Plug Wires - Original design with screw in ends. For tractor models B275, B414, B434, 354, 364, 424, 444, 2424, 2444, 3414, 3444, with gas engines with Lucas distributors with threaded plug wires. 2 wires at 10-1/2 inches long, 1 wire 14-1/4 inches long, 1 wire 17-3/4 inches long and the coil wire is 9 inches long. Replaces 3044219R93, 181604M91, 181605M91, 825708M91, TO12284. (Item #: 111200, Ref: B5217) $41.00
Spark Plug Wire Set, Custom - IH or Delco Distributors and Magnetos. For the following models with 90 degree angle boots: A, I4, AV, Super A, Super A1, Super AV, SuperAV1, B, BN, C, Super C, Cub, Cub Lo-Boy, 154, 184, 185, H, HV, Super H, Super HV, M, MD, Super M, Super MD, Super MDV, MDV, Super MDVTA, MTA, Super MTA, MV, Super MV, Super MVTA, O4, O6, ODS6, OS4, OS6, T340, T5, T6, TD6, SuperW4, W4, Super W6, Super W6TA, W6, W6TA, Super WD6, WD6, 100, 130, 140, 200, 230, 240, 300, 330, 340, 350, 400, W400, 404, 424, 444, 450, W450, 504. Replaces the following OEMS: 352947R91, 352951R91, 352954R91, 352956R91, 356687R92, 356689R92, 356691R91, 356694R92, 356695R92, 356697R93, 362439R91, 362789R91, 407487R1, 45327DA, 46277DA, 50075D, 52794D, 65352D, 65357D, 65358D, and 65359D. (Item #: 120100, Ref: S.67475) $15.20
Starter - 12 volt, clockwise rotation, 10 teeth. For tractor models (B275 1964-1968 with 4-144 diesel), (B414 1964-1967 with 4-154 engine), 424, (B434, B444 1966-1976 with diesel engine), (B354 1973-1976 with diesel engine), 364, 384, 2300, 2350, 3414, 2424, 3444 Replaces International part numbers: 3046890R92, 3046890R93, 704447R91, 704447R92, 704447R93, 704447R94, 704447R95. Replaces Luca 26132, 26132A, 26132B, 26132C, 26132D, 26132E, 26132F, 26132H, 26132J, 26132K, 26132L, 26132M, 26132N, 26132O, 26132P, 26132Q, 26132R, 26193, 26193A, 26193B, 26193C, 26193D, 26288, 26288A, 26288B, 26288C, 26288D, 26288E, 26288F, 27420, 27420A, 27420B, NSB504, S4511, S4517, S4560. (Item #: 112137, Ref: 704447R95) $185.00
Starter - Replacing Delco starter numbers 1108323, 1109589 this is a new 12 volt 10MT Delco style starter with 9 tooth drive. It is direct drive with clockwise rotation. Used on gas International 2424, 2444, 424, 444. Also replaces 104192A1 (Item #: 160373, Ref: 396587R91) $290.00
No Picture Starter - Delco Style (4243), Remanufactured, Delco Remy, 1108323, 104192A1 - For International / Farmall tractor models 424, 444, 2444 (all gas), Replaces International OEM number 104192A1, 396587R91, Replaces Delco Remy manufacturer number 1108323, 1109589, Replaces manufacturer number 4243, 140-706, 91-01-4179, Delco Style, Voltage: 12, Rotation: Clockwise, Teeth: 9, For a New version of this sku use Item #: 160373, (Item #: 203456) $283.54
Starter - Delco Style DD (4218), Remanufactured, Delco Remy, 323-687, 388813R91 - For International / Farmall tractor models 424 (Diesel), 444 (Diesel), Compatible with International Construction and industrial models 2424 (Diesel), 2444 (Diesel), Replaces International OEM number 388813R91, Replaces Delco Remy manufacturer number 323-687, 1107585, Type: Direct Drive, Voltage: 12, Teeth: 10, Rotation: Clockwise, (Item #: 210981) $307.44
No Picture Starter Drive - Starter drive, services Delco starter: 1107585. Tractors: 424, 444, 2424, 2444. 10 teeth. For 2424, 2444, 424, 444 (Item #: 179564, Ref: 1846554) $36.70
Starter Drive - Starter drive, services Delco starters: 1108323, 1107364. For tractor models 424, 444, 656, 2424, 2444, 2656. 9 teeth. For 2424, 2444, 2656, 424, 444, 656. Also replaces 1946220. (Item #: 127285, Ref: 1892899) $34.00
Starter Drive Housing - This Starter Nose Cone is used on Delco starter numbers 1107021, 1107060, 1107067, 1107093, 1107174, 1107427, 1107448, 1108096. Bushing is included. This part replaces Delco part numbers 1878661, 1887109, 1910093, 1943759 (Item #: 179382, Ref: 1878661) $75.01
Starter Switch - Momentary Push Button Ignition Switch. Rubber boot covers push button, 2 screw type terminals, used extensively on I.H. equipment. Serves as starting, horn or reverse lock out switch. Used on various combines, windrowers, balers, cotton pickers, hay conditioners and grain platforms. Also used on Tractors: IHC: Fits: 240, 300, 330, 340, 350, 400, 404, 424, 444, 450, 460, 504, 560, 606, 656, 660, 706, 806, 4100, 4156, 4166, 4186; Industrial: 1206, 2656; Crawler: T4, T5, TD5. Replaces 366317R91, 366317R93GV (Item #: 112232, Ref: 366317R93) $7.60
Starting Button - Attaches with eyelets and screws. For tractor models 240, 300, 330, 340, 350, 400, 404, 424, 444, 460, 504, 560, 606, 656, 660, 706, 806, 1206, 4100, 4156, 4166, 4186. (Item #: 112232, Ref: A36948) $7.60
Switch, Push Button - This 2 Terminal Switch has many applications. It is a heavy duty momentary switch, push for on and release for off. It is rated for up to 35 volts. Uses two screw terminals. The mounting stem is 5/8 inch number 32 thread. It is 21/32 inch over all length. Check measurements before ordering if using as a universal part. Applications include Ether Switch, Horn Button, Cold Start, Starter Switch and Manifold Heater Switch. Replaces: 271179R91, 367678R91, 373611R91, 393209R91. (Item #: 121141, Ref: R7994) $12.00
Switch, Push Button - This 2 Terminal Switch has many applications. It is a heavy duty momentary switch, push for on and release for off. It is rated for up to 35 volts. Uses two screw terminals. The mounting stem is 5/8 inch number 32 thread. It is 21/32 inch over all length. Check measurements before ordering if using as a universal part. Applications include Ether Switch, Horn Button, Cold Start, Starter Switch and Manifold Heater Switch. Replaces: 271179R91, 367678R91, 373611R91, 393209R91. (Item #: 121141, Ref: R7994) $12.00
Tune-up Kit - This Tune-up Kit is for IH Distributors - NOT Delco. Complete Kit For: 100, 130, 140, 200, 230, 240, 300, 330, 340, 350, 4, 400, 404, 424, 444, 450, 6, A, AV, B, BN, C, H, HV, M, Super AV, Super C, Super H, Super HV, Super M, Super MTA, Super W4, Super W6, Super W6TA, Super A, Cub, Cub Lo-boy, Cub 154 Lo-Boy, Cub 185 Lo-Boy. All with 4 cylinder gas engines and IH distributor from 1951 through 1962. Contains: Points, Autolite Spark Plugs (AL386), Condenser, rotor. NOT FOR USE ON EARLY MODELS WITH A MAGNETO. (Item #: 111814, Ref: IHTK1) $31.00
Voltage Regulator, 12 Volt - Flat Mount Voltage Regulator. For tractor models 2404, 2424, 2504, 2606, 2656, 2706, 2806, 404, 424, 504, 606, 656, 706, 806. Replaces Delco 1119000, 35A5137 1118897, 121579C1, 375055R1. (Item #: 105521, Ref: 121579C1) $92.00

Engine Bearings
Cam Bearing Set - Camshaft bearing kit, 3 bearings. Individual bearings not available. For BD154 CID diesel engine in tractors 238, 364, 384, B414, 424, 434, 444, 2424, 2444. For 238, 2424, 2444, 354, 364, 384, 424, 4324, 434, 444, B250, B275, B276, B414 (Item #: 106663, Ref: CBK-H144) $38.10
Connecting Rod Bearing, .010" - For International / Farmall tractor models B250, B275, B276, B414, 354, 364, 384, 424, 434, 444, Compatible with International Construction and industrial models 2424, 2444, Replaces Case IH OEM number 3070539R1, (Item #: 168919) $19.60
Connecting Rod Bearing - .010" Oversize - Set - For International / Farmall tractor models B275, B414, 354, 364, 384, 424, 444, 2424, 2444, 3444, Compatible with International Construction and industrial models 3414, 3444, Compatible with International Engine (s) BC144 (gas), BD144 (diesel), BD154 (diesel), Replaces International OEM number 1082408R91, Sold in complete sets, Bearing Size: .010" Oversize, For Standard connecting rod bearing use Item #: 106460, (Item #: 106458) $17.87
Connecting Rod Bearing - .020" Oversize - Set - For International / Farmall tractor models B275, B414, 354, 364, 384, 424, 444, 2424, 2444, 3444, Compatible with International Construction and industrial models 3414, 3444, Compatible with International Engine (s) BC144 (gas), BD144 (diesel), BD154 (diesel), Replaces International OEM number 1082410R91, Bearing Size: .020" Oversize, Sold in complete sets, For Standard connecting rod bearing use Item #: 106460, (Item #: 106459) $15.10
Connecting Rod Bearing - .030" Oversize - Set - For International / Farmall tractor models B275, B414, 354, 364, 384, 424, 444, 2424, 2444, 3444, Compatible with International Construction and industrial models 3414, 3444, Compatible with International Engine (s) BC144 (gas), BD144 (diesel), BD154 (diesel), Replaces International OEM number 3070537R11, 3070547R91, Sold in complete sets, Bearing Size: .030" Oversize, For Standard connecting rod bearing use Item #: 106459, (Item #: 106460) $20.20
Main Bearings - .010" Oversize - Set - For International / Farmall tractor models 404, 424, 444, 504, 2404, 2424, 2444, 2504, Compatible with International Engine (s) C135, C146, C153, Replaces International OEM number 376660R11, 376661R11, Sold in complete set, Bearing Size: .010" Oversize, For Standard main bearing use Item #: 106591, (Item #: 106589) $168.00
Main Bearings - .010" Oversize - Set - For International / Farmall tractor models B275, B414, B434, 354, 364, 384, 424, 444, 2424, 2444, 3444, Compatible with International Construction and industrial models 3414, 3444, Compatible with International Engine (s) BC144, BD144, BD154, Sold in complete set, Bearing Size: .010" Oversize, For Standard main bearing use Item #: 106595, (Item #: 106593) $37.10
Main Bearings - .020" Oversize - Set - For International / Farmall tractor models 404 (Gas), 424 (Gas), 444 (Gas), 504 (Gas), 2404 (Gas), 2424 (Gas), 2444 (Gas), 2504 (Gas), 3514 (Gas), Compatible with International Engine (s) C135 (Gas (sn:100501-later), C146 (Gas), C153 (Gas), Replaces International OEM number 376664R11, 376663R11, Gas engines, Sold in complete set, Bearing Size: .020" Oversize, For Standard main bearing use Item #: 106591, (Item #: 106590) $174.00
Main Bearings - .020" Oversize - Set - For International / Farmall tractor models B275, B414, B434, 354, 364, 384, 424, 444, 2424, 2444, 3444, Compatible with International Construction and industrial models 3414, 3444, Compatible with International Engine (s) BC144, BD144, BD154, Sold in complete set, Bearing Size: .020" Oversize, For Standard main bearing use Item #: 106595, (Item #: 106594) $34.90
Main Bearings - .030" Oversize - Set - For International / Farmall tractor models B275, B414, B434, 354, 364, 384, 424, 444, 2424, 2444, 3444, Compatible with International Construction and industrial models 3414, 3444, Compatible with International Engine (s) BC144, BD144, BD154, Replaces International OEM number 3070537R11, 3070547R91, Sold in complete set, Bearing Size: .030" Oversize, For Standard main bearing use Item #: 106594, (Item #: 106595) $78.00
No Picture Main Bearing Set .030 - For 330, 340, 404 with C135 Engine (from engine serial number 100501 - main journal would measure 2.624 inch standard size), 424, 444, 504 with C146 or C153 4 cylinder gas engines. (Item #: 106591, Ref: MS-665P-030) $83.98
Main Bearing Set - Standard - For International / Farmall tractor models B275, B414, B434, 354, 364, 384, 424, 444, 2424, 2444, 3444, Compatible with International Construction and industrial models 3414, 3444, Compatible with International Engine (s) BC144, BD144, BD154, Replaces International OEM number 3064523R11, 708910R91, Sold in complete set, Bearing Size: Standard, For .010" main bearing use Item #: 106595, (Item #: 106592) $49.00
Main Bearings - Standard - Set - For International / Farmall tractor models 404, 424, 444, 504, 2404, 2424, 2444, 2504, Compatible with International Engine (s) C135 (gas), C146 (gas), C153 (gas), Replaces International OEM number 375755R11, 375762R11, Sold in complete set, Bearing Size: Standard, For .010" main bearing use Item #: 106591, (Item #: 106588) $141.00
Piston Pin Bushing - Used in British International engines: BC144, BD144, BD144A, BD144C, BD154, BD154C, BD154T. This Piston Pin Bushing has an inside diameter of 27.5mm. Used in International models: B275, B414, 424, 444, 354, 365, 384, 3414, 2424, 2444, 238, 500. Replaces OEM numbers 3043611R1, 711045R1, 3043611R93 (Item #: 108502, Ref: 3043611R1) $4.20
No Picture Rod Bearing - Single bearing in standard. For tractor models 330, 340, 404 with C135 engine serial number 100501 and up. For tractor models 330, 340, 404 all with C135 engine serial number 100501 and up. 424, 444, 454, 504, 454, 2400A, 2400B, 2405B, 2410B, 2412B with C146 or C153 4-cylinder gas engines. Standard journal measures 2.060 inches. Replaces 375723R11, 7375723, and CB-533P. Sold individually. (Item #: 106453) $17.40
No Picture Rod Bearing - Single bearing in .010. For tractor models 330, 340, 404 with C135 engine serial number 100501 and up. For tractor models 330, 340, 404 all with C135 engine serial number 100501 and up. 424, 444, 454, 504, 454, 2400A, 2400B, 2405B, 2410B, 2412B with C146 or C153 4-cylinder gas engines. Journal measures 2.050 inches. Replaces 376656R11, 7376656, and CB-533P-010. Sold individually. (Item #: 106454) $23.00
No Picture Rod Bearing - Single bearing in 0.20. For tractor models 330, 340, 404 with C135 engine serial number 100501 and up. For tractor models 330, 340, 404 all with C135 engine serial number 100501 and up. 424, 444, 454, 504, 454, 2400A, 2400B, 2405B, 2410B, 2412B with C146 or C153 4-cylinder gas engines. Journal measures 2.040 inches. Replaces 376658R11, 7376658, and CB-533P-020. Sold individually. (Item #: 106455) $23.00
No Picture Rod Bearing - Single bearing in 0.030. For tractor models 330, 340, 404 with C135 engine serial number 100501 and up. For tractor models 330, 340, 404 all with C135 engine serial number 100501 and up. 424, 444, 454, 504, 454, 2400A, 2400B, 2405B, 2410B, 2412B with C146 or C153 4-cylinder gas engines. Journal measures 2.030 inches. Replaces 375724R11, 7375724, and CB-533P-030. Sold individually. (Item #: 106456) $10.80
Rod Bearing Set - For tractor models B250, B275, B276, 354, 434. (BD144 and BD144A CID Diesel 4-cylinder engine and for tractor models 238, 364, 384, B414, 424, 434, 444, 2424, 2444. (BD154 CID Diesel 4-cylinder engine. Flat head pistons. If other than standard, specify size in comments. (.010, .020). (Item #: 106457, Ref: CRK4154D) $16.00

Engine Gaskets
No Picture Conversion Gasket Set - For tractor models 330, 340, 404 with C135 engine serial number 100501 and up. 424, 444, 504 with C146 or C153 4 cylinder gas engines. (Item #: 106722, Ref: CS3287VC) $90.00
Front Crank Seal - Front seal, for diesel engines. For 238, 2424, 2444, 354, 364, 384, 424, 434, 444, B250, B275, B276, B414 (Item #: 106641, Ref: 3108650R91) $9.50
Front Crankshaft Seal - For International / Farmall tractor models A, B, C, Cub, Cub Lo-Boy, Super A, Super C, 100, 130, 140, 200, 230, 240, 330, 340, 404, 424, 444, 504, 2404, 2424, 2444, 2504, Compatible with International Engine (s) C60 (Gas and LP), C113 (Gas and LP), C123 (Gas and LP), C135 (Gas and LP), C146 (Gas and LP), C153 (Gas and LP), Replaces International OEM number 379620R92, 378193R91, 350708R1, 355769R1, 46179DC, (Item #: 106638) $14.60
Front Crankshaft Wear Sleeve - This Front Crankshaft Wear Sleeve is used in British Diesel Engines: BC144, BD144, BD144A, BD144C, BD154, BD154C, BD154T. It is used to repair wear where the front crank shaft seal goes into the front timing cover. (Item #: 184669, Ref: RP301112) $68.00
Full Gasket Set with Crankshaft Seals - For International / Farmall tractor models B250, B275, B276, B414, 354, 384, 424, 444, Compatible with International Engine (s) BD144 (s/n 26077-later), BD154 (s/n 26077-later), Replaces International OEM number 3041249R91, 3041249R92, 3041249R93, 3041249R94, 706106R91, 706106R92, 706106R93, 706106R94, (Item #: 186327) $105.01
Gasket, Manifold, Pack of 2 - Used with 251175R1 Manifold. Fits Models: A, B, C, Super C, Super AV, AV, BN, T340, T5, Super A, 100, 130, 140, 200, 240, 330, 340, 404, 424, 444, A1, T4B, AI, All with 113, 123, 135, 146 and 153 CID Gas, LP or Distallate engines. Price is for two. Replaces 24520D, 24520DA, 352014R1, 48696D, 48696DA (Item #: 101551, Ref: 352014R1) $12.00
Gasket set - Complete Gasket Set For tractor models B250, B275, B276, 354, 434. (BD144 and BD144A CID Diesel 4-cylinder engine and Models 238, 364, 384, B414, 424, 434, 444, 2424, 2444. (BD154 CID Diesel 4-cylinder engine. Flat head pistons (Item #: 164341, Ref: GK4154D) $119.00
No Picture Head Gasket - For International / Farmall tractor models B250 (Diesel), B275 (Diesel), B276 (Diesel), B414 (Diesel), 364 (Diesel), 384 (Diesel), 424 (Diesel), 434 (Diesel), 444 (Diesel), Compatible with International Construction and industrial models 2444 (Diesel), Replaces International OEM number 703883R7, 703883R8, 703883R2, 703883R1, Replaces manufacturer number VPA4335, (Item #: 174281) $25.80
Head Gasket Set - For tractor models 404, 2404 both with C135 gas engine serial number 100501 and up. 424 with C146 gas engine. 444, 504, 2444, 2504, and 3514 with C153 gas engine. (Item #: 106683, Ref: HS3287VC) $45.00
Liner Sealing Ring - For International / Farmall tractor models B275, B414, B434, 354, 364, 384, 424, 444, 2424, 2444, 3444, Replaces International OEM number 704100R1, 1 required per cylinder sleeve, (Item #: 128744) $2.70
Lower Gasket Set - For BD154 and BD144 CID 4 cylinder diesel engines. For tractor models 238, 2424, 2444, 354, 364, 384, 424, 434, 444, B250, B275, B276, B414. Replaces 3048863R91, 3041249R1, 3041249R92, 3041249R94 (Item #: 106723, Ref: CS4154D) $65.00
No Picture Lower Gasket Set Gas - For tractor models 424, 444, 504, 454, 2400A, 2400B, 2405B, 2410B, 2412B all with C157 gas engine and 544, 574, 674 all with C200 gas engine. (Item #: 185102, Ref: CS3535) $145.00
No Picture Manifold Gasket - For International / Farmall tractor models B, C, Super A, Super C, 100, 130, 140, 200, 230, 240, 330, 340, 404, 424, 444, 504, 2404, 2424, 2444, 2500, 2504, 3514, Compatible with International Combine (s) 105, 203, Compatible with International Construction and industrial models 500, Replaces International OEM number 352014R4, (Item #: 167139) $7.30
Oil Pan Gasket - Oil pan gasket. For BD154 CID diesel 4 cylinder engine in tractors 238, 364, 384, B414, 424, 434, 444, 2424, 2444. For 238, 2424, 2444, 354, 364, 384, 424, 434, 444, B250, B275, B276, B414 (Item #: 106701, Ref: 703840R1) $7.10
Pre-Combustion Chamber Upper Gasket - For International / Farmall tractor models B275, B414, TD5, 354, 364, 424, 434, 444, 2444, Replaces International OEM number 710382R3, Fits Between Pre Combustion Chamber and Pre Combustion Chamber Holder, (Item #: 184222) $2.60
Rear Crank Seal - Rear seal, for diesel engines. 3.630" I.D x 4.380" O.D. x 0.435" Wide For 238, 2424, 2444, 276, 354, 364, 384, 424, 434, 444, B250, B275, B276, B414 Replaces: 3072092R1, 3072092R91, 708903R91 (Item #: 106655, Ref: 3072092R91) $9.05
Timing Cover Gasket Set - This Timing Cover Gasket Set contains: Governor housing gasket, Water pump plate gasket, Fan bracket gasket, Timing cover gasket, Front crankshaft seal with seal saver and Lower water outlet gasket. Use on C113, C123, C135, C146, and C153 Gas or LP engines. Fits A, AV, B, BN, C, Super A, Super AV, Super C, 100, 130, 140, 200, 230, 240, 2404, 2424, 2444, 2504, 330, 3514, 404, 424, 444, 504. Replaces OEM part numbers: 45875D, 375745R1, 375745R2, 43294D, 43294DA, 46179D, 46179DC, 43442D, 49177D, 378193R91, 46871D, 68104C1, 68104C2. (Item #: 182535, Ref: 46179DKit) $32.00
Upper Gasket Set - Upper Gasket Set for 4 Cylinder Diesel Engine. For tractor models 2424, 2444, 354, 364, 384, 424, 434, 444, B250, B275, B276, B414. (Item #: 106684, Ref: 706105R93) $43.00
Valve Cover Gasket - This Valve Cover Gasket is used on Gas Engines; C113, C123, C135, C146, C153. It replaces OEM/Original part numbers 43378DB, 43378DD, 43378DE. (Item #: 128613, Ref: 43378DE) $10.40
Valve Cover Gasket - For International / Farmall tractor models B275, B414, B434, 354, 364, 384, 424, 444, 2424, 2444, 3444, Compatible with International Construction and industrial models TD5, 500, Compatible with International Engine (s) BC144 (gas), Replaces International OEM number 3069767R1, 3069767R2, Replaces manufacturer number 73069767, (Item #: 158264) $7.40
Valve Seals - Valve Guide Seal - Positive Type (Item #: 183858, Ref: 386192R1) $3.30

Engine Rebuild Kits
No Picture Basic Engine Overhaul Kit, Less Bearings - For tractor models 238, 364, 384, B414, 424, 434, 444, 2424, 2444. (BD154 CID Diesel 4-cylinder engine. Flat head pistons). Kit contains sleeves and sleeve seals, pistons and piston rings, pins and retainers, pin bushings, complete gasket set with crankshaft seals. ENGINE BEARINGS ARE NOT INCLUDED. (Item #: 130583, Ref: BEKH4154D-LCB) $494.00
No Picture Basic In-Frame Engine Kit - For tractor models 238, 364, 384, B414, 424, 434, 444, 2424, 2444. (BD154 CID Diesel 4-cylinder engine. Flat head pistons). Kit contains complete sleeve and piston kit with rings, pins and retainers, valve grind gasket set and pan gasket. (Item #: 189598, Ref: BIFH4154D) $536.00
Cylinder Sleeve - For International / Farmall tractor models B414, B434, 364, 384, 424, 444, 2424, 2444, 3444, Compatible with International Construction and industrial models 3414, Compatible with International Engine (s) BD154 (s/n 57679-later), Replaces International OEM number 3044481R3, Sleeve Flange Diameter: 3.996", (Item #: 128729) $48.50
No Picture Valve Overhaul Kit, 2 Spring - Cylinder Head Overhaul Kit with Inner and Outer Valve Springs. For tractor models 238, 2424, 2444, 354, 364, 384, 424, 434, 444, B250, B275, B276, B414 all with either BD144, BD144A or BD154 engines. Includes intake valves, exhaust valves, valve guides, valve springs. Valve locks, part number 704443R1 are sold individually. (Item #: 184962, Ref: VOKH144) $171.00

Engine Parts
No Picture AH935R - Single. For tractor models B250, B275, B276, 354, 434. (BD144 and BD144A CID Diesel 4-cylinder engine) and for tractor models 238, 364, 384, B414, 424, 434, 444, 2424, 2444. (BD154 CID Diesel 4-cylinder engine). Flat head pistons. (Item #: 168486, Ref: 3043825R1) $11.10
No Picture Bare Block, Remanufactured, 375597R1 - For International / Farmall tractor models 424, 504, 2504 (gas), Replaces International Casting number 375597R1, Engine (s): C153, Casting Number: 375597R1, Our remanufactured bare blocks have been; cleaned, inspected, align bored, and pressure checked, (Item #: 205084) $1275.01
Camshaft - For tractor models B275, B414, 424, 434, 444, 354, 364, 384, 3414, 2424, 2444, TD5, EARLY 500 with diesel engines. Replaces 709450R1, 3063934R3, 3064086R91. Verify 1 5/16 inch diameter on cam where cam gear fits on. Replacement gear available as part number 3064085R1. (Item #: 112371, Ref: 3063934R3) $96.00
Camshaft Gear - This Camshaft Gear is used with 3063934R3 Camshaft. Replaces 3064085R1, 703812R1 (Item #: 112370, Ref: 3064085R1) $32.60
Camshaft Retaining Plate - This Camshaft Retaining (Thrust) Plate used on IH B275, B414, 424, 434, 444, 354, 364, 384, 3414, 2424, 2444, TD5, EARLY 500. Replaces 43249D (Item #: 180159, Ref: 43249D) $7.70
Camshaft Timing Gear - 66 teeth. For tractor models (100, 130, 140, 200, 230, 240, Super C all with 123 CID engine), (330, 340, 404 all with 135 CID engine), (424 with 146 CID engine), (444, 504 with 153 CID), (A, AV, B, BN, C, Super A, Super A1, Super AV, Super AV1 with 113 CID engine). Replaces 375712R1, 6779DB. (Item #: 111038, Ref: 375712R1) $92.00
Connecting Rod - For tractor models 2424, 384, 424, 444, B414, with the BC144, BD144, BD154 gas/diesel engines engine. Replaces 3061214R91, 3061215R1, 061214R91, 306215R1, 704088R91, 706132R1 (Item #: 108438, Ref: 3061214R91) $51.00
Connecting Rod, Remanufactured, 375595R1 - For International / Farmall tractor models 404, 424, 444, 454, 504, 2400A, 2400B, 2404, 2424, 2444, 2504 (& 4500B tractors), Replaces International Casting number 375595R1, Casting number 375595R1, (Item #: 203742) $279.50
Crankshaft - For tractor models 2424, 354, 364, 384, 424, 2300b 275, B414 all with either a BD144, or BD154 engine. Replaces 3110995R91, 751303R1 (Item #: 112327, Ref: 3110995R91) $324.72
Crankshaft Gear - This Crankshaft Gear used on IH B275, B414, 424, 434, 444, 354, 364, 384, 3414, 2424, 2444, TD5, EARLY 500. Replaces 703865R1 (Item #: 112413, Ref: 703865R1) $36.40
Crankshaft Gear, Used - For International tractor models A, B, C, Super A, Super C, 200, 230, 240, 330, 340, 404, 424, 504, 2404, 2424, 2504, Compatible with International Engine(s) C123, C135, C146, C153, Compatible with International Hay Cutting(s) 201, Replaces International OEM nos 46870DA, Replaces Casting nos 46879DA, 33 Teeth, Inside Diameter: 1.25", Used items are not always in stock. If we are unable to ship this part we will contact you within one business day., (Item #: 497149) $89.01
No Picture Crankshaft, Remanufactured, 375600R - For International / Farmall tractor models 404 (with C135 engine), 424 (with C146 engine), Replaces Casting number 375600R, Our remanufactured crankshafts are cleaned, magnafluxed, measured and reground if necessary, the journals are then polished., (Item #: 200239) $630.01
Crankshaft Timing Gear - 33 teeth, used in C113, C123, C135, C146, and C153 Engines. For tractor models A, Super A, AV, Super AV, B, BN, C, Super C, 130, 140, 200, 230, 240, 330, 340, 404, 424, 444, 504, 2404, 2424, 2444, 2504. (Item #: 121687, Ref: 46870DA) $65.00
No Picture Cylinder Head, Remanufactured, 366206R - For International / Farmall tractor models 330, 340, 404, 424, 444, 504 (Gas), Replaces International Casting number 366206R, Casting No. 366206R, Engine 135, Cylinders: 4, Not a welded head, Our remanufactured cylinder heads are reconditioned and ready for assembly, with both valve guides and valve seats installed, Cleaned and tested for cracks, (Item #: 205495) $550.01
Cylinder Head, Remanufactured, 366299R - For International / Farmall tractor models 330, 340, 404, 424, 444, 504 (Gas), Replaces International Casting number 366299R, Engine 135, Cylinders 4, Casting No. 366299R, Our remanufactured cylinder heads are reconditioned and ready for assembly, with both valve guides and valve seats installed, Cleaned and tested for cracks, (Item #: 200197) $810.01
No Picture Cylinder Head, Remanufactured, 375602R - For International / Farmall tractor models 330, 340, 404, 424, 444, 504 (Gas), Replaces International Casting number 375602R, Engine 135, Cylinders: 4, Not a welded head, Our remanufactured cylinder heads are reconditioned and ready for assembly, with both valve guides and valve seats installed, Cleaned and tested for cracks, (Item #: 205497) $800.01
No Picture Cylinder Head, Remanufactured, 375775R - For International / Farmall tractor models 330, 340, 404, 424, 444, 504 (Gas), Replaces International Casting number 375775R, Casting No. 375775R, Engine 135, Cylinders: 4, Not a welded head, Our remanufactured cylinder heads are reconditioned and ready for assembly, with both valve guides and valve seats installed, Cleaned and tested for cracks, (Item #: 205496) $630.01
No Picture Cylinder Head, Remanufactured, 703873R3 - For International / Farmall tractor models B275, B414, 354, 424, 444 (Diesel), 454, 2424, 2444, 3444, Compatible with International Construction and industrial models 3414, 3444, Replaces International Casting number 703873R3, Engine BD-144, Cylinders: 4, Casting No. 703873R3, Not a welded head, Our remanufactured cylinder heads are reconditioned and ready for assembly, with both valve guides and valve seats installed, Cleaned and tested for cracks, (Item #: 203719) $900.01
No Picture Cylinder Head, Used - For International tractor models B275, B414, 354, 424, 444 (Diesel), 2444, 3444, Replaces International Casting nos 3043824R, 304489R, Engine(s): BD154, Cylinders: 4, Our used cylinder heads have been visually inspected for cracks, Cylinder head may require further cleaning, inspection, or machining before use, Used items are not always in stock. If we are unable to ship this part we will contact you within one business day., (Item #: 400195) $350.01
No Picture Cylinder Head, Used - For International tractor models 240, 340, 404, 424, 444, 504 (Gas), Replaces International Casting number 366206R, Engine(s): 135, Cylinders: 4, Our used cylinder heads have been visually inspected for cracks, Cylinder head may require further cleaning, inspection, or machining before use, For a Remanufactured version of this part use Item #: 205495, Used items are not always in stock. If we are unable to ship this part we will contact you within one business day., (Item #: 405495) $291.01
Cylinder Head, Used - For International tractor models 330, 340, 404, 424, 444, 504 (Gas), Replaces International Casting number 375602R, Engine(s): 135, Cylinders: 4, Our used cylinder heads have been visually inspected for cracks, Cylinder head may require further cleaning, inspection, or machining before use, For a Remanufactured version of this part use Item #: 205497, Additional Handling and Oversize Fees Apply To This Item, Used items are not always in stock. If we are unable to ship this part we will contact you within one business day., (Item #: 405497) $475.01
No Picture Cylinder Head, Used - For International tractor models 240, 340, 404, 424, 444, 504 (Gas), Replaces International Casting number 375775R, Engine(s): 135, Cylinders: 4, Our used cylinder heads have been visually inspected for cracks, Cylinder head may require further cleaning, inspection, or machining before use, For a Remanufactured version of this part use Item #: 205496, Used items are not always in stock. If we are unable to ship this part we will contact you within one business day., (Item #: 405496) $213.01
Cylinder Head with Valves - For tractor models B250, B275, B276, 354, 238, 364, 384, B414, 424, 434, 444, 2424, 2444 with BD154 and BD144 engines. Also replaces OEM 3043824R1, 3044489R91, 3043824R1 and 703872R98. Does not include prechamber cups. (Item #: 112328, Ref: 3043824R12) $524.00
No Picture Governor Thrust Bearing Assembly - This 3 piece bearing assembly slides onto the governor assembly. For models cub, A, B, C, Super C, 560, Super AV, 184, AV, Bn, Cub Lo-Boy, Super A, 100, 130, 140, 154, 185, 200, 230, 240, 330, 340, 404, 424, 444, 460, 504. Also replaces 55314D. (Item #: 184444, Ref: 43481D) $52.00
Lifter, Refaced - These Valve Tappets (Lifters) are used on IH B275, B414, 424, 434, 444, 354, 364, 384, 3414, 2424, 2444, TD5, EARLY 500. Diesel all with casting number 704782R1. Replaces 704782R1. (Item #: 112412, Ref: R1188333) $5.90
No Picture Piston and Ring Set, Standard - This is a Standard 3.375 inch bore piston and ring set for 424 and 2424 tractors with C146 Engine. Contains Pistons, Pins, Retainers and Rings. Replaces 388558R92 pistons and 539363R1 rings. (Item #: 184878, Ref: R8195) $500.00
Pushrod - Fits A, AV, B, BN, C, Super A, Super A-1, Super AV, Super AV-1, Super C, U2, U2A, 100, 130, 140, 200, 230, 240, 330, 340, 404, 424, 444, 504, 2404, 2424, 2444, 2504 (all with C113, C123, C135, C146, C153 gas/LP engines) 10.762 inch length, 0.310 inch tube diameter . Replaces: 360213R91, 357548R1, 47386D, 47385D. (Item #: 182498, Ref: 47385D) $43.00
No Picture Push Rod, Used - For International tractor models A, B, BN, C, Super A, Super AV, Super C, 200, 230, 240, 330, 340, 404, 424, 444, 504, 2404, 2424, 2444, 2504, Compatible with International Engine(s) C123, C135, C146, C153, Compatible with International Hay Cutting(s) 201, Replaces International OEM number 357548R1, For a new version of this item use Item #: 182498, Used items are not always in stock. If we are unable to ship this part we will contact you within one business day., (Item #: 463344) $24.01
Ring Gear - Ring Gear. For tractor models 2424, 384, 424, 444, B275, B414 (Item #: 165196, Ref: 704436R1) $45.54
Ring Gear, Flywheel - This Flywheel Ring Gear measures 12.332 Inch Inside Diameter, 13.560 Inch Outside Diameter, Has 134 Teeth and is .485 Inches wide. Fits International Tractors; 300 diesel, 330 diesel, 340 diesel, 350 diesel, 424 gas, 444, 460, (504 diesel serial number 13675 and earlier, gas serial number 29632 and earlier), 544 with Synchromesh Transmission, 606 gas, 656, 666, 686, 2424, 2444, 2544 with Synchromesh Transmission, 2606, 3514 engine serial number 29632 and earlier. Also fits Construction and Industrials; T340, 4000. Replaces 367042R1 (Item #: 121882, Ref: 367042R1) $61.00
No Picture Valve Guide - Guide intake valve, 4 used per engine. For BD154 CID diesel 4 cylinder engine in tractors 238, 364, 384, B414, 424, 434, 444, 2424, 2444. For 238, 2424, 2444, 354, 364, 384, 424, 434, 444, B250, B275, B276, B414 (Item #: 184557, Ref: 3044492R1) $6.90
No Picture Valve Guide, Exhaust - For tractor models 238, 2424, 2444, 354, 364, 384, 424, 434, 444, B250, B275, B276, B414. Price shown is for each, sold only in multiples of 4 items. (Item #: 173141, Ref: 3044493R2) $4.70
No Picture Valve, Intake Set - Set of 4 Intake Valves. For tractor models B250, B275, B276, 354, 434. (BD144 and BD144A CID Diesel 4-cylinder engine) and for tractor models 238, 364, 384, B414, 424, 434, 444, 2424, 2444. (BD154 CID Diesel 4-cylinder engine). Flat head pistons. (Item #: 168477, Ref: 3040361R1) $16.10
Valve Key - VALVE KEY. For tractor models 238, 2424, 2444, 354, 364, 384, 424, 434, 444, B250, B275, B276, B414. NOTE: 16 halves required for a complete engine. Sold individually. (Item #: 168426, Ref: 704443R1) $1.10
No Picture Valve Service Kit - Cylinder HEAD Service KIT For 238, 2424, 2444, 354, 364, 384, 424, 434, 444, B250, B275, B276, B414. Contains: springs, guides, locks, (no valves). (Item #: VSKH144) $684.81
Valve Spring - For International / Farmall tractor models 330, 340, 404, 424, 444, 504, 2404, 2424, 2444, 2504, Compatible with International Engine (s) C135, C153, Replaces International OEM number 368450R1, Exhaust, (Item #: 128648) $9.60

Engine Pistons and Sleeves
No Picture Piston and Ring Set, .020 - This is a 0.020 inch overbore (3.375 + 0.020) inch bore piston and ring set for 424 and 2424 tractors with C146 Engine. Contains pistons, pins, retainers and rings. Replaces 388560R92 and 539364R1 (Item #: R8196) $244.30
No Picture Piston and Ring Set, .030 - This is a 0.030 inch overbore set (3.375 + 0.030 inch bore) piston and ring set for 424 and 2424 tractors with C146 Engine. Contains Pistons, Pins, Retainers and Rings. Replaces 388561R92 pistons and 539365R1 rings. (Item #: R8197) $255.30
No Picture Piston and Ring Set, .040 - This is a 0.040 inch overbore set (3.375 + 0.040 inch bore) piston and ring set for 424 and 2424 tractors with C146 Engine. Contains Pistons, Pins, Retainers and Rings. Replaces 388562R92 Pistons and 539366R1 Rings (Item #: R8198) $255.30
Piston Pin Bushing - Piston pin bushing, 4 used per engine. For C135, C146, C153, C157 CID gas 4 cylinder engines. Stepped head piston. For tractor models 2400A, 330, 340, 404, 424, 444, 504, 2504, 454, 3514, 2404, 2424, 2444, 2400B, 2405B, 2410B, 2412B, 4500. (Item #: 128635, Ref: 367775R1) $6.90
No Picture Sleeve and Piston Kit - For tractor models 238, 364, 384, B414, 424, 434, 444, 2424, 2444. (BD154 CID Diesel 4-cylinder engine. Flat head pistons.) Sleeves in this kit measure 3.995 diameter at the flange. Verify this measurement. Sleeves, pistons and rings, pins and retainers. For 3-1/2 inch standard bore. (Item #: PK4154D) $379.50

Engine Rings
No Picture Piston - For International / Farmall tractor models B250, B275, B276, B414, 354, 364, 384, 424, 434, 444, Replaces International OEM number PA778, B513013, 304480R94, 3044486R2, Bore: 3.478", (Item #: 176668) $54.00
No Picture Piston Ring Set - Piston Ring set for 4 pistons~ 1 used per engine. For BD154 CID diesel, 3 1/2 inch bore, 4 cylinder engine. Contains 3 compression 3/32 and 2 oil rings 3/16 for each cylinder. For 238, 2424, 2444, 364, 384, 424, 434, 444, B414 (Item #: 174209, Ref: PRS4154D) $65.00
No Picture Piston Ring Set - .020" Oversize - 4 Cylinder Set - For International / Farmall tractor models 424, 444, 454, 504, 2404, 2424, 2444, 2504 (all gas), Compatible with International Engine (s) C153, C157, Standard Bore: 3.375", Ring Size: .020" Oversize, Compression Rings per Piston: (2) @ .094", Oil Rings per Piston: (1) @ .188", Top Groove Size: .094", Top Groove Style: Barrel Face Triple Chrome, 2nd Groove Size: .094", 2nd Groove Style: Reverse Torsional Taper Face, 3rd Groove Size: .188", 3rd Groove Style: Chrome Rail / Oil Ring Spacer, Sold as 4 cylinder set, For Single Cylinder Piston Ring Set use Item #: 120856, (Item #: 174302) $93.00
Piston Ring Set - .020" Oversize - Single Cylinder - For International / Farmall tractor models 424, 444, 454, 504, 2404, 2424, 2444, 2504 (all gas), Compatible with International Engine (s) C153, C157, Standard Bore: 3.375", Ring Size: .020" Oversize, Compression Rings per Piston: (2) @ .094", Oil Rings per Piston: (1) @ .188", Top Groove Size: .094", Top Groove Style: Barrel Face Triple Chrome, 2nd Groove Size: .094", 2nd Groove Style: Reverse Torsional Taper Face, 3rd Groove Size: .188", 3rd Groove Style: Chrome Rail / Oil Ring Spacer, Sold per cylinder, For 4 Cylinder .020" Oversize Piston Ring Set use Item #: 174302, (Item #: 120856) $27.10
Piston Ring Set - .030" Oversize - 4 Cylinder - For International / Farmall tractor models 424, 444, 454, 504, 2404, 2424, 2444, 2504 (all gas), Compatible with International Engine (s) C153, C157, Standard Bore: 3.375", Ring Size: .030” Oversize, Compression Rings per Piston: (2) @ .094", Oil Rings per Piston: (1) @ .188", Top Groove Size: .094", Top Groove Style: Barrel Face Triple Chrome, 2nd Groove Size: .094", 2nd Groove Style: Reverse Torsional Taper Face, 3rd Groove Size: .188", 3rd Groove Style: Chrome Rail / Oil Ring Spacer, Sold per 4 cylinder set, For single cylinder use Item #: 150214, (Item #: 179376) $98.00
Piston Ring Set - .030" Oversize - Single Cylinder - For International / Farmall tractor models 424, 444, 454, 504, 2404, 2424, 2444, 2504 (all gas), Compatible with International Engine (s) C153, C157, Standard Bore: 3.375", Ring Size: .030” Oversize, Compression Rings per Piston: (2) @ .094", Oil Rings per Piston: (1) @ .188", Top Groove Size: .094", Top Groove Style: Barrel Face Triple Chrome, 2nd Groove Size: .094", 2nd Groove Style: Reverse Torsional Taper Face, 3rd Groove Size: .188", 3rd Groove Style: Chrome Rail / Oil Ring Spacer, Sold per cylinder, For standard use Item #: 150214, (Item #: 120857) $25.60
No Picture Piston Ring Set - .040" Oversize - 4 Cylinder Set - For International / Farmall tractor models 424, 444, 454, 504, 2404, 2424, 2444, 2504 (all gas), Compatible with International Engine (s) C153, C157, Standard Bore: 3.375", Ring Size: .040” Oversize, Compression Rings per Piston: (2) @ .094", Oil Rings per Piston: (1) @ .188", Top Groove Size: .094", Top Groove Style: Barrel Face Triple Chrome, 2nd Groove Size: .094", 2nd Groove Style: Reverse Torsional Taper Face, 3rd Groove Size: .188", 3rd Groove Style: Chrome Rail / Oil Ring Spacer, Sold as 4 Cylinder Piston Ring set, For Single Cylinder .040" Oversize Piston Ring Set use Item #: 120858, (Item #: 174303) $95.00
Piston Ring Set - .040" Oversize - Single Cylinder - For International / Farmall tractor models 424, 444, 454, 504, 2404, 2424, 2444, 2504 (all gas), Compatible with International Engine (s) C153, C157, Standard Bore: 3.375", Ring Size: .040” Oversize, Compression Rings per Piston: (2) @ .094", Oil Rings per Piston: (1) @ .188", Top Groove Size: .094", Top Groove Style: Barrel Face Triple Chrome, 2nd Groove Size: .094", 2nd Groove Style: Reverse Torsional Taper Face, 3rd Groove Size: .188", 3rd Groove Style: Chrome Rail / Oil Ring Spacer, Sold per cylinder, For .040" Oversize - 4 Cylinder Piston Ring Set use Item #: 174303, (Item #: 120858) $15.98
Piston Ring Set - .060" Oversize - 4 Cylinder - For International / Farmall tractor models 424, 444, 454, 504, 2404, 2424, 2444, 2504 (all gas), Compatible with International Engine (s) C153, C157, Replaces International OEM number 539367R1, Standard Bore: 3.375", Ring Size: .060” Oversize, Compression Rings per Piston: (2) @ .094", Oil Rings per Piston: (1) @ .188", Top Groove Size: .094", Top Groove Style: Barrel Face Triple Chrome, 2nd Groove Size: .094", 2nd Groove Style: Reverse Torsional Taper Face, 3rd Groove Size: .188", 3rd Groove Style: Chrome Rail / Oil Ring Spacer, Sold as a complete 4 cylinder set, For standard use Item #: 150213, (Item #: 150214) $211.00
Piston Ring Set - Standard - 4 Cylinder - For International / Farmall tractor models 424, 444, 454, 504, 2404, 2424, 2444, 2504 (all gas), Compatible with International Engine (s) C153, C157, Ring Size: Standard, Compression Rings per Piston: (2) @ .094", Oil Rings per Piston: (1) @ .188", Top Groove Size: .094", Top Groove Style: Barrel Face Triple Chrome, 2nd Groove Size: .094", 2nd Groove Style: Reverse Torsional Taper Face, 3rd Groove Size: .188", 3rd Groove Style: Chrome Rail / Oil Ring Spacer, Sold as 4 cylinder set, For single cylinder set use Item #: 150214, (Item #: 179373) $104.00
No Picture Piston Ring Set - Standard - Single Cylinder - For International / Farmall tractor models B414, 364, 384, 424, 444, 2424, 2444, 3444, Compatible with International Construction and industrial models 500, 3414, Compatible with International Engine (s) BD154, BD154T, Bore: 3.500", Ring Size: Standard, Compression Rings per Piston: (3) @ .094", Oil Rings per Piston: (2) @ .188", Top Groove Size: .094", Top Groove Style: Barrel Face Triple Chrome, 2nd Groove Size: .094", 2nd Groove Style: Reverse Torsional Taper Face, 3rd Groove Size: .094", 3rd Groove Style: Reverse Torsional Taper Face, 4th Groove Size: .188", 4th Groove Style: FV Spacer .125 " / Chrome Rail, 5th Groove Size: .188", 5th Groove Style: Cast Iron Oil, Sold per cylinder, For 4 Cylinder Piston Ring Set use Item #: 174209, (Item #: 120851) $23.00

Exhaust System
Exhaust/Intake Manifold - Manifold for the C-123, C-135, C-146, C-153 gas engines in models: 130, 140, 20, 230, 240, 330, 340, 404, 2404, 424, 2424, 444, 2444 (T-4, T-5, T340 and 500 Crawler). Uses threaded exhaust fitting. Replaces part numbers 366305R11, 369645R21, 369645R22, 388584R11, 388584R21. Does not include gaskets set available as part number 352014R1. Does not include short exhaust pipe available as part number R0056P. 2-3/8 inch center-to-center carburetor mounting holes, 1-3/16" outside diameter exhaust ports at cylinder head. MAY OR MAY NOT COME PAINTED PER PICTURE. (Item #: 101550, Ref: R0935) $175.00
Exhaust Manifold Gasket - This gasket is used with 3042719R11 manifold. Two are required. Sold individually. Replaces 704165R1, 704165R2, 704165R3, VPE3933. (Item #: 113661, Ref: 704165R2) $10.60
Exhaust Manifold, Vertical - For tractor models B275, 354, 384, B414, 444, 2300, 2444 all with diesel engines. Gasket available as p/n 704165R2. Replaces 3042719R11, 3045354R11. NOTE - THIS MAY BE SLIGHTLY DIFFERENT THAN YOUR ORIGINAL MANIFOLD AND YOUR HEAT SHIELD MAY NEED TO BE TRIMMED AS THIS CASTING MAY BE SLIGHTLY LARGER. (Item #: 113663, Ref: 3042719R11) $57.00
Exhaust Stack - 2-3/8" X 36", Curved Chrome - For International / Farmall tractor models H, M, Super H, Super M, Super MTA, Super W4, Super W6, W4, W6, 300, 340, 350, 400, 424, 450, 454, 460, 544, 560, 574, 656, 660, 706 (all with 2-3/8" O.D. manifold pipe), Style: Curved, Inlet I.D.: 2-3/8", O.D.Pipe: 2-1/2", Length: 36", Chrome Plated, Eliminates Muffler, Additional Handling and Oversize Fees Apply To This Item, (Item #: 115481) $165.88
Exhaust Stack - 2-3/8" X 36", Curved Chrome - For International / Farmall tractor models H, M, Super H, Super M, Super W4, Super W6, W4, W6, 300, 340, 350, 400, 424, 450, 454, 460, 544, 560, 574, 656, 660, 706 (all with 2-3/8" O.D. manifold pipe), Replaces International OEM number A29991, Style: Curved, Inlet I.D.: 2-3/8", O.D. Pipe: 4", Length: 36", Chrome Plated, Eliminates Muffler, Additional Handling and Oversize Fees Apply To This Item, (Item #: 115486) $209.00
Exhaust Stack - 2-3/8" X 36", Straight Chrome - For International / Farmall tractor models Super H, Super M, Super W4, Super W6, W4, W6, 300, 340, 350, 400, 424, 450, 454, 460, 544, 560, 574, 656, 660, 706 (all with 2-3/8" O.D. manifold pipe), Replaces International OEM number 62476D, Style: Straight, Inlet I.D.: 2-3/8", O.D. Pipe: 3", Length: 36", Chrome Plated, Eliminates Muffler, (Item #: 115487) $134.11
Extension Pipe with Gasket - For Diesel tractor models B250, B275, 354, 384, B414, 444, 2300, 2444. Replaces 3072544R1, 704613R1, 704614R1. Measures 1-55/64 inches pipe O.D., 5.600 inches overall length, 3.225 inches C-C bolt pattern. (Item #: 113662, Ref: 3072544R1) $23.80
Manifold Pipe - This manifold pipe screws into manifold numbers R0935 and 251175R1. Inside diameter is 1 1/2 inch, outside diameter 1 15/16 inch. Length between 6 and 8 inches. For tractor models 130, 140, 20, 230, 240, 330, 340, 404, 2404, 424, 2424, 444, 2444, A, B, C, Super A, Super C, 240. Replaces: 47701DB. (Item #: 101544, Ref: R0056P) $11.00
Muffler - Vertical muffler for gas tractors, fits engines C146, C153, and BC144. Inlet inside diameter 1-15/16 inch, outlet outside diameter 2 inches, length 27 inches, diameter 5-1/2 inches. For tractor models 424, 2424, 444, 504, 2444, 2500, 2504, 3514, 3444. For 2424, 2444, 2500, 2504, 3444, 3514, 424, 444, 504. (Item #: 100808, Ref: 403825R1) $47.30
Muffler - Horizontal Exhaust inlet inside diameter 1 7/8 inch, outlet outside diameter 1 3/4 inch, overall length 38 inch. For B414, International 424 Tractors, International 2424 Industrial. All with B144 Gas Engine. OEM number use R1750 clamp. (Item #: 100820, Ref: 3047572R93) $49.30
Muffler Clamp - Muffler clamp. For 100, 130, 140, 200, 230, 240, 340, 404, 424, 460, 504, 560, 606, 656, 660, 664, A, B, C, Super AV, Super C, Super A bad part (Item #: 180044, Ref: 48889DA) $13.70
Muffler Clamp - Flanged Muffler Clamp. This clamp is serviceable but not exactly like the original for the following Gas and LP tractors with underslung exhaust system: 2444, 2504, 330, 404, 444, 504, 340, 424, 240, 300, 350. Also used on T4 Gas or LP crawler with underslung exhaust. Replaces original part number 362300R1 (Item #: 101515, Ref: FP185) $4.90
Muffler Eliminator - 2-3/8" X 24", Straight Chrome - For International / Farmall tractor models H, M, Super H, Super M, Super W6, W4, W6, 300, 340, 350, 400, 424, 450, 454, 460, 544, 560, 574, 656, 660, 706 (all with 2-3/8" O.D. manifold pipe), Inlet I.D: 2-3/8", O.D. Pipe: 3", Length: 24", Straight Pipe, Chrome Plated, Eliminates Muffler, (Item #: 115491) $81.17
Muffler - Restoration Quality - For International / Farmall tractor models 140, 240, 330, 340, 404, 424, 444, 504 Also fits Farmall: A, B, C, Super A, Super C, 100, 130, 200 and 230 if a larger diameter outlet is desired., Compatible with International Construction and industrial models T340, Compatible with International Hay Cutting (s) 201, Replaces International OEM number 360720R91, 381665R92, 403825R1, High Temperature Paint, Restoration Quality Muffler, IH Logo and part number are stamped into the side of the muffler, Inlet Length: 2-1/4", Inlet ID: 1-61/64", Shell Length: 16-1/2", Shell Diameter: 4-1/4", Outlet Length: 10", Outlet OD: 1-25/32", Overall Length: 28-3/4", (Item #: 164534) $63.00
Muffler - Restoration Quality - For International / Farmall tractor models 140, 240, 330, 340, 404, 424, 444, 504 Also fits Farmall: A, B, C, Super A, Super C, 100, 130, 200 and 230 if a larger diameter outlet is desired., Compatible with International Construction and industrial models T340, Compatible with International Hay Cutting (s) 201, Replaces International OEM number 360720R91, 381665R92, 403825R1, Polished Stainless Steel, Restoration Quality muffler, IH Logo and part number are stamped into the side of the muffler, Inlet Length: 2-1/4", Inlet ID: 1-61/64", Shell Length: 16-1/2", Shell Diameter: 4-1/4', Outlet Length: 10", Outlet OD: 1-25/32", Overall Length: 28-3/4", (Item #: 164535) $150.00