International Harvester / Farmall 3230 Tractor Parts

[Categories]   [All Farmall Models]   [Print]  

Brakes
Brake Disc - 10.190 inch outside diameter, 15 internal splines. For tractor models Used on International models 2400, 2400A, 248, 2500, 2500A, 268, 3220, 3230, 380B, 385, 395, 4210, 4230, 4240, 454, 464, 474, 484, 485, 495, 574, 584, 595, 674, 684, 685, 695, 784, 884, 885, 895, 995, C100, C50, C60, C70, C80, C90, CX100, CX50, CX60, CX70, CX80, CX90, Hydro 84. Replaces 1027256C1, 114621C1, 114622C2, 399734R1 (Item #: 105452, Ref: 114622C2) $94.00
Brake Master Cylinder - This Brake Master Cylinder Rod is 3/8 inch x 24 pitch thread. It is used on 3220, 3230, 4210, 4230, 4240, 485XL, 5.9L Engine, 5120, 5130, 5140, 5220, 5230, 5240, 5250, 585XL, 595, 685, 695, 785XL, 856XL, 885, 885XL, 895, 995, CX100, CX50, CX60, CX70, CX80, CX90, MX100, MX100C, MX110, MX120, MX135, MX80C, MX90C. Replaces 1287734C92, 226301A1, 3129643R91. (Item #: 122351, Ref: 1287734C92) $64.00
Brake Master Cylinder - This Brake Master Cylinder is used on IH Tractors: 3220, 3230, 385, 395, 4210, 4230, 4240, 485, 495, 595, 685, 695, 885, 895, 995, C100, C50, C60, C70, C80, C90. It Replaces original part number 1287843C92 (Item #: 124544, Ref: 1287843C92) $90.00
Brake Plate - The measurements on the Brake Plate are ID: 8 1/8 inches (206mm) with 3 tabs, OD: 10 1/4 inches (259mm). This part replaces 399736R3, 984439C1. Used on International models 2400, 2400A, 248, 2500, 2500A, 268, 3220, 3230, 380B, 385, 395, 4210, 4230, 4240, 454, 464, 474, 484, 485, 495, 574, 584, 595, 674, 684, 685, 695, 784, 884, 885, 895, 995, C100, C50, C60, C70, C80, C90, CX100, CX50, CX60, CX70, CX80, CX90, Hydro 84 (Item #: 105456, Ref: 399736R3) $84.77

Clutch
No Picture Clutch Alignment Tool - 1-1/8 inch 10 spline, 1-5/8 inch 10 spline, 3/4 inch pilot. For tractor models 364, 384, 385, 395, 494, 574, 584, 585, 595, 895, 995, 3230, 4210, 4220, 2400A, 2400B, (424, 2444 with single disc), 2500A, 2500B, 3500, 3500A. (Item #: 113942, Ref: S.70912) $26.50
Clutch Disc - 12 inch disc (6 large pads), 1-1/8 inch hub, 10 spline. For tractor models 895, 995, 3210, 3220, 3230, 3400, 3434, 4210, 4220, 4230, 4240, 584, 684, 784, 884. (Item #: 122009, Ref: 85026C3) $155.00
Clutch Disc - For Models: 2400, 2400A, 2400B, 248, 2500A, 2500B, 258, 268, 3400A, 3434A, 3434B, 3500, 3500A, 3514, 380B serial number below 18106, 4500A, 4500B, 3210, 3220, 3230, 3400, 485, 485L serial number below 8250, 485XL serial number below 703, 495, 574, 584, 674, 684 serial number below 10338, 685L serial number below 12349, 685XL serial number below 3234, 784 serial number below 9490, 785L serial number below 16712, 785XL serial number below 1840, 884 serial number below 9396, 885 serial number below 3083, 885L serial number below 2690, 885XL serial number below 2990 11 inch diameter, 1-1/8 inch hub, 10 spline, 6 ceramic pads. Replaces 1944253C1, 293248A1, 3121507R93, 70093C91. (Item #: 122012, Ref: 70093C91) $137.00
Clutch Kit - This New Clutch Kit, includes 537290R91 pilot bearing, 158125C91 release bearing, 85025C2 pressure plate-10 spline, 1 5/8 inch hub-12 inch diameter, 85026C3R clutch drive disc-10 spline with 1 1/8 inch hub and 10 spline-1 1/8 inch by 10 spline 1 5/8 inch pilot tool. Fits 3210 PATRIOT, 3220, 3230, 380B LOADER, 4210, 4220, 4230, 4240, 495, 584, 585, 595, 684, 685, 695, 784, 786, 795, 884, 885, 895, 985, 995. (Item #: 115343, Ref: 1712-7070) $400.00
Pressure Plate Assembly, 11 Inch - 11 inch outside diameter, 3 spring-3 finger, 10 spline with 1 5/8 inch hub. Clutch plate for Gas and Diesel applications. 2400, 2400A, 2400B, 248, 2500A, 2500B, 258, 268, 3400A, 3434A, 3434B, 3500, 3500A, 3514, 380B serial number below 18106, 4500A, 4500B, 3210, 3220, 3230, 3400, 485, 485L serial number below 8250, 485XL serial number serial number below 10338, 685L serial number below 12349, 685XL serial number below 3234, 784 serial number below 9490, 785L serial number below 16712, 785XL serial number below 1840, 884 serial number below 9396, 885 serial number below 3083, 885L serial number below 2690, 885XL serial number below 2990. Replaces 1500655C91, 1500655C92, 1500655C93, 1500655R1, 2726336C91, 529566R92, 68211C91, 70716C1, 92602C92, 128005541, 70716. (Item #: 150356, Ref: 68211C91) $145.00
Pressure Plate Assembly, 12 Inch - This is a 12 inch, 10 spline with 1 5/8 inch center hub pressure plate. It is used on 3210 Patriot, 3220, 3230, 380B Indust/Const, 4210, 4220, 4230, 4240, 495, 584 Indust/Const, 595, 684, 685, 695, 784, 795, 884, 885, 895, 985, 995. Replaces 84342556, 85025C2, 85025C2R. (Item #: 110580, Ref: 85025C2) $168.00

Cooling System
Radiator Cap - This 10 pound radiator cap with cover is used on multiple tractors. It replaces original part numbers 527425R1, 532672R91, 532029R1, 532029R2, 3118639R1, 1500626C91. (Item #: 114950, Ref: 1500626C92) $15.60

Drive Train
Torque Amplifier Clutch Kit - Power shift, 6 friction plates, 4 steel plates, 2 piston seals. For tractor models 684, 784, 884, 485, 585, 685, 885, 395, 495, 595, 695, 895, 995, 4210, 3220, 3230, 4230, 4240, C50, C60, C80, C90, C100. Replaces 401717R3, 401724R1, 402571R1. (Item #: 124618, Ref: 401716R3) $151.00

Electrical System
Ignition Switch - This ignition kit with keys is used on multiple Case/IH tractors with Cabs and Digital Dashes. It replaces original part numbers 1987424C1, 1533738C1 and A187614. For tractor models 3210, 3220, 3230, 385, 395, 4210, 4220, 4230, 4240, 440, 485, 495, 5120, 5130, 5140, 5150, 5220, 5230, 5240, 5250, 540, 585, 595, 640, 685, 695, 740, 743, 745, 785, 795, 840, 844, 845, 856, 885, 895, 940 and 995. (Item #: 164183, Ref: 1987424C1) $40.70
Starter Drive - Clockwise rotation, 10 teeth. Fits Lucas 26428A and Magnetti Marelli starters. For tractor models Hydro 84, 385, 395, 484, 485, 495, 584, 585, 595, 684, 685, 695, 784, 884, 885, 895, 995, 3220, 3230, 4210, 4230, 4240. (Item #: 112574, Ref: 84209C2) $25.20
Starter Motor - Fits 454, 474, 574, 674, 484, 584, 684, 784, 884, 6858, 485, 485XL, 585, 585XL, 685, 685XL, 785, 785X, 885, 885XL, 985XL, 395, 495, 495XL, 595, 595XL, 695, 695XL, 795, 795XL, 895, 895XL, 995XL, 2310, 3220, 3230, 4210, 4220, 4230, 4240, 84 Hydro. Replaces these starter numbers in the above models: B514002, SLU0013, TS-1212, TS-4030, 1107867, 114568A1, 114568A2, 114568A3, 189330A5, 1998343, 230428A1, 230428A3, 537140R91, 537140R96, SDR0214. (Item #: 104180, Ref: 537140R95) $167.00

Engine Bearings
Rod Bearing Standard - This is a single rod bearing for International Engines: D155, D179, D206, D239, D246, D268, D310, D358. Replaces 3055218R1. Order on for each connecting rod. (Item #: 191598, Ref: CRK239D) $7.00

Engine Gaskets
Rear Crank Seal Diesel - For the following engines: D327-4, TD327-3, DT268 Turbo Diesel, D155 Diesel, D179 CID, D206 CID, D226-B6, D226-3, D226-4, D226-6, D227-4, D227-6, D239 CID, D246 Diesel, D268 Diesel, D310 CID, D325-2, D325-3, D327-2, D327-3, D358 CID, TD226-B6, TD226-4, and TD228-6. Inside diameter 110mm, Outside diameter 130mm, Width 12.7mm. Does not include wear sleeve. Order RP301113 if wear sleeve is need. Replaces 7701021418, 6005605198, 3138701R91, X550174902000, 89965016008 (Item #: 106657, Ref: 3138701R91) $20.10
Rear Crank Wear Sleeve - This Rear Crankshaft Seal is used for 110mm rear crankshafts on: D155 Diesel Engine, D179 Diesel Engine, D206 Diesel Engine, D239 Diesel Engine, D246 Diesel Engine, DT268 Diesel Engine, D310 Diesel Engine, D358 Diesel Engine. Used with 3138701R91 Seal (not included). (Item #: 106658, Ref: RP301113) $153.00

Engine Parts
Flywheel - Flywheel assembly with ring gear. 12 inch diameter. Tractors: 574, 584, 585, 595, 684, 685, 695, 784, Hydro 84, 3230, 4210. Weight: 88.5 pounds. Additional $20 shipping due to weight. (Item #: 103897, Ref: 1808412C92) $590.00

Exhaust System
Exhaust Elbow Gasket - For tractor models 474, 574, 584, 585, 595, 674, 684, 685, 695, 784, 785, 884, 885, 895, 3230, 4210, 4220, 4230. (Item #: 160788, Ref: 3136248R1) $3.40
Exhaust Manifold Gasket - Manifold to head, sold individually 4 required for application. For tractor models 474, 574, 584, 585, 595, 674, 684, 685, 695, 784, 785, 884, 885, 895, 3230, 4210, 4220, 4230. (Item #: 101558, Ref: 3132434R1) $4.00
Manifold - For tractor models 474, 574, 584, 585, 595, 674, 684, 685, 695, 784, 785, 884, 885, 895, 3230, 4210, 4220, 4230. (Item #: 124679, Ref: 3136066R12) $182.00

Fuel System / Air Intake
Fuel Injector Nozzle Sleeve - This Fuel Injector Nozzle Sleeve is used on D155, D179, D206, D239, D246, D268, DT268, D310, and D358 Engines. Brass Construction, 3.190 inch overall length 0.386 inch injector tip inside diameter. Replaces 73055344, 3055344R1 (Item #: 165847, Ref: 3055344R1) $24.60
Fuel Shutoff Valve - The threads on this fuel shutoff valve are 1/2 - 20 and 3/8 - 18 NPTF. Used on C50, C60, C70, C80, C90, C100, 385, 395, 485, 495, 585, 595, 685, 695, 785, 885, 895, 995, 3220, 3230, 4210, 4230, 4240, Hydro 84, 248, 258, 268, 278, 385, 454, 464, 474, 484, 485, 574, 584, 585, 674, 684, 685, 784, 785, 884, 885, 2400, 2400A, 2500, 2500A (Item #: 135040, Ref: 528926R1) $24.00
Injector Nozzle - For tractor models 385, 395, (484 serial number 379592 and up), 485, 495, 584, 585, 595, 3220, 3230, 380B. Replaces DLLA150S836. (Item #: 179947, Ref: 3218248R2) $47.50
Manifold Heater - Thermostart Intake Manifold Heater Diesel Engines. Has Applications in many Diesel Models. Replaces Part Numbers: 218349A1, 162000090701, A77616, 3112805R91, K928523, 3118299R1 (Item #: 118792, Ref: 3583543M2) $10.90

Gauges
Tractormeter Cable - Cable Housing is 70 inches long. For tractor models 3210, 3220, 3230, 385, 4210, 4220, 4230, 4240, 484, 485, 584, 585, 585A, 595, 684, 685, 685A, 685XL, 695, 784, 785, 785XL, 795, 85XL, 884, 885, 885XL, 895. Replaces 537494R91, 1536644C1, 1500492C1, 1500716C1, 402024R91. (Item #: 121529, Ref: 537494R91) $28.20

Hitch / Drawbar
Leveling Box Assembly - Cat II, 13-5/8 inch screw. For tractor models 3220, 3230, 395, 4210, 4230, 4240, 495, 595, 695, 895, 995. (Item #: 113621, Ref: 1713-1003) $173.00
Leveling Box Assembly - Cat II, 15.25 inch screw. For tractor models 3220, 3230, 395, 4210, 4230, 4240, 495, 595, 695, 895, 995. (Item #: 124555, Ref: 1713-1004) $115.00
Leveling Box Fork - This Leveling Box Fork is 14.50 inches long, has a 1-5/8 inch fork width and 0.875 inside diameter. This is a CAT II part. It is used on 3220, 3230, 395, 4210, 4230, 4240, 495, 574, 584 Indust/Const, 595, 674, 684, 685, 695, 784, 884, 885, 895, 995. It is used with 527937R1 Nut, not included. Replaces 402635R4. (Item #: 110393, Ref: 402635R4) $77.00
Leveling Box Screw - This level box screw with bevel gear is 0.875 inches dia, 18.125 inches long. Tractors: 3220, 3230, 395, 4210, 4230, 4240, 495, 595, 695, 895, 995. Replaces 223322, 3072422R2, 3116725R91, 3121964R4. (Item #: 124707, Ref: 3116725R91) $62.62
Leveling Fork Nut - This Leveling Fork Nut is used with 3121964R1 and 402635R4 fork. Replaces original part number 527937R1. (Item #: 110735, Ref: 527937R1) $7.00
Leveling Rod Fork - Housing, leveling screw. Cat I. (14.500 inches long) 1 inch wide fork. Tractors: Hydro 84, 385, 395, 454, 464, 484, 485, 495, 574, 584, 585, 595 with fixed lower link, 674, 684, 685 with fixed lower link, 695, 784 with fixed lower link, 895, 995 ; 3220, 3230 with out telescopic lower link; 4210, 4230, 4240 with out telescopic lower link. (Item #: 108812, Ref: 3121964R91) $66.00
Leveling Yoke Left Hand - This Left Hand Leveling Yoke is 19.250 inches long and 0.875 inch, 9 UNC thread. It replaces original part numbers 527935R1, 527948R91 (Item #: 124678, Ref: 527948R91) $33.60

Hydraulic System
Filter, Hydraulic Oil - 5-1/16 inch outside diameter, 2-11/16 inch inside diameter, 3 inches tall. For tractor models (385 serial number 5001 to 5287 and 18001 and up), 485, 585, 685, 885, 395, 495, 595, 695, 895, 3220, 3230, 4210, 4230, 4240, C50, C60, 380B. (Item #: 164964, Ref: 93413C1) $29.10

Lights
Headlight Assembly - Pair - Features Glass Lenses with Bulbs, Mounting Hardware and Trim - Left and Right Pair. Replaces 1964881C2, 1964882C2 (Item #: 160300, Ref: R7945) $387.47

Steering
Axle Support Bushing - Used on Carraro 4WD front ends, this bushing measures 4.921 inches outside diameter, 4.527 inches inside diameter and is 1.653 inches long. Replaces OEM numbers K965756, K965265, 1-33-241-048, 9967992, K965265, CAR101575/1, CAR123477, CAR1015751, 9967992, 83930079, 83930554, R113767, 3541395M1 (Item #: 156131, Ref: CAR1015751) $91.21
Bushing, Front Axle Steering Arm - For tractor models 385, 395, 454, 474, 475, 484, 485, 485XL, 495, 495XL, 574, 584, 585, 585XL, 595, 595XL, 674, 684, 685, 685XL, 695, 695XL, 784, 785, 785XL, 795, 795XL, 884, 885, 885XL, 895, 895XL, 995, 995XL, 2400, 2500, 3220, 3230, 4210, 4220, 4230, 4240, C50, C60, C70, C80, C90, CX50, CX60, CX70, CX80, CX90, CX100. Replaces 153687C1. (Item #: 104494, Ref: 405574R1) $6.90
Bushing, Front Axle, Steering Arm - Associated with 379555R11 steering arm. For tractor models 385, 395, 454, 474, 475, 484, 485, 485XL, 495, 495XL, 574, 584, 585, 585XL, 595, 595XL, 674, 684, 685, 685XL, 695, 695XL, 784, 785, 785XL, 795, 795XL, 884, 885, 885XL, 895, 895XL, 995, 995XL, 2400, 2500, 3220, 3230, 4210, 4220, 4230, 4240, C50, C60, C70, C80, C90, CX50, CX60, CX70, CX80, CX90, CX100. (Item #: 104493, Ref: 379748R1) $9.00
Front Axle Bolt - Used to secure front axle knees, this bolt measures 4-3/4 inches overall, 4 inches to the shoulder and has 3/4-16 UNF RH Thread. If nuts are needed, order 116643. Replaces part number 405584R1 (Item #: 124558) $10.00
Front Axle - Differential Housing Bushing - The measurements on this bushing are: 4.525 inches outside diameter, 4.127 inches inside diameter, 1.730 inches long. This bushing is used on Carraro 4WD front end. Replaces OEM numbers 101565, K965266, CAR1015651, 83945601, CAR101565/1, CAR123478, 83930062, 9967993, R113766, 3541396M1, 040953R1 (Item #: 156132, Ref: CAR1015651) $79.00
Front Axle Nut - Used with part number 124558 to secure axle knees, this nut is 3/4 inch -16 UNF thread. Replaces 405576R1 (Item #: 116643) $2.40
Power Steering Cylinder Plate - Used on 3210, 3220, 3230, 385, 395, 4210, 4220, 4230, 4240, 454, 474, 475, 484, 485, 495, 584 Indust/Const, 595, 674, 684, 685, 695, 784, 785, 795, 884, 885, 895, 995, C100, C50, C60, C70, C80, C90, CX100, CX50, CX60, CX70, CX80, CX90, MX100C, MX80C, MX90C (Item #: 124616, Ref: 405580R21) $41.00
Power Steering Cylinder Rod - Used on UK built International 2 wheel drive tractors, this part replaces 549668R1, 549668R2, 188851A1, 549668R3, 188854A1. Used on 238, 248, 258, 268, 288, 3210, 3220, 3230, 385, 395, 4210, 4220, 4230, 4240, 454, 474, 475, 484, 485, 485XL, 495, 495XL, 574, 584, 585, 585XL, 595, 595XL, 674, 684, 685, 685XL, 695, 695XL, 784, 785, 785XL, 795, 795XL, 884, 885, 885XL, 895, 895XL, 995, 995XL, CX100, CX50, CX60, CX70, CX80, CX90, Hydro 84, Hydro 86, MX100C, MX80C, MX90C (Item #: 182916, Ref: 549668R1) $298.00
Seal Kit, Power Steering Cylinder - For 2 wheel drive models 454, 464, 574, 674, 484, 584, 684, 784, 884, 385, 485, 585, 685, 885, 595, 695, 995, 2400, C50, C60, C80, C90, C100, 4210, 4230, 4240. VERIFY PART NUMBER TO ENSURE CORRECT REPLACEMENT. (Item #: 115098, Ref: 55355C91) $39.90
Spindle Felt Seal - This Felt Washer is used with 405840R12 and 534288R91 Spindles. Fits tractor models 238, 248, 258, 385, 395, 454, 475, 474, 484, 485, 485XL, 495, 495XL, 574, 584, 585, 585XL, 595, 595XL, 674, 685, 695, 885, 895, 3220, 3230, 4210, 4230 and 4240. (Item #: 102176, Ref: 15943DA) $2.20
Spindle, L/R - This spindle works both Left hand and right hand. Shaft length 12.125 inch, shaft diameter 1.687 inch, inner bearing 1.375 inch, outer bearing .842 inch. For models 238, 248, 258, 385, 395, 454, 474, 475, 484, 485, 485XL, 495, 495XL, 574, 584, 585, 585XL, 595, 595XL, 674, 685, 695, 885, 895, 3220, 3230, 4210, 4230, 4240, C50, C60. The wheel bearing kit used for this spindle is part number WBKIH6. (Item #: 100844, Ref: 405840R12) $223.00
Spindle Nut - Fits on Front Spindles. Castle Nut 3/4 inch x 16 UNF. P2060, VLG3307, 351129S, 353928X1, 354573S36, 387930S36, 646060M1, 83416613, 83900513, 83910701, 880284M1, 9073, 98A750N, 129-290, 88886, 427639, 88886 (Item #: 156038, Ref: 387930S36) $1.10
Spindle, RH/LH - This spindle measures A= 8.312 inch, B= 1.667 inch, C= 1.780 inch, D= 1.375 inch. For tractor models 268, 278, 3230, 4210, 4230, 4240, 584, 585, 595, 595XL, 684, 685, 685XL, 695, 695XL, 784, 785, 884, 885, 885XL, 895, 895XL, 995, C100, C70, C80, C90, CX100, CX70, CX80, CX90, Hydro 84. The wheel bearing kit used for this spindle is part number WBKIH9. (Item #: 100846, Ref: 3121270R91) $169.71
Spindle, RH/LH - This spindle measures A= 11.250 inch, B= 1.667 inch, C= 1.780 inch, D= 1.375 inch. For tractor models 268, 278, 3230, 4210, 4240, 585, 595, 595XL, 684, 685, 685XL, 695, 695XL, 784, 785, 884, 885, 885XL, 895, 895XL, C100, C70, C80, C90, CX100, CX70, CX80, CX90, Hydro 84. The wheel bearing kit used for this spindle is part number WBKIH9. (Item #: 104329, Ref: 3121261R91) $201.00
Steering Arm, Left Hand - This is a left hand steering arm use on adjustable front axel. 52 inch to 77 inch Used on IH models 268, 278, 3230, 4210, 4230, 4240, 584 Indust/Const, 585, 684, 685, 695, 784, 785, 884, 885, 895, 995, CX100, CX70, CX80, CX90, Hydro 84 Replaces 3121263R1 (Item #: 124740, Ref: 3121263R1) $313.00
Steering Arm, Right Hand - This Right Hand Steering Arm is used on 268, 278, 3230, 4210, 4230, 4240, 585, 595, 684, 685, 695, 784, 785, 884, 885, 895, 995, CX100, CX70, CX80, CX90, Hydro 84. It replaces 3121264R1 (Item #: 124741, Ref: 3121264R1) $261.00
Steering Bar Assembly - For tractor models 238, 248, 258, 268, 288, 3210, 3220, 3230, 385, 395, 4210, 4220, 4230, 4240, 454, 474, 475, 484, 485, 485XL, 495, 495XL, 574, 584, 585, 585XL, 595, 595XL, 674, 684, 685, 685XL, 695, 695XL, 784, 785, 785XL, 795, 795XL, 84 Hydro, 884, 885, 885XL, 895, 895XL, 995XL. (Item #: 124616, Ref: 405580R11) $41.00
Steering Joint - This Steering Joint is 7.040 over all length. The Inner Thread is M20 X 1.5 RH Thread. The Outer Thread is M18 X 1.5 LH Thread. Replaces 1966127C1, 83957148, CAR49006, 1-33-743-602, 112508A1 (Item #: 104634, Ref: CAR49006) $57.00
Steering Motor, Hydrostatic - With relief valve. For tractor models (385, 485, 585 serial number 18001 and up), 380B, 3220, 3230, 4210, 4230, 4240, C50, C80, C90, C100. Replaces 88107C91, 88107C92, 88107C93. (Item #: 104331, Ref: 88107C93) $480.00
Steering Wheel Cap - For tractor models 1026, 1066, 1086, 1206, 1256, 1456, 1466, 1468, 1566, 1568, 1586, 186, 2400, 2500, 3088, 3220, 3230, 3288, 3388, 3588, 3688, 3788, 404, 424, 4386, 444, 454, 4586, 464, 4786, 484, 504, 5088, 5288, 544, 5488, 574, 584, 606, 6388, 656, 6588, 664, 666, 674, 6788, 684, 686, 706, 756, 766, 784, 786, 806, 826, 856, 884, 886, 966, 986, HYDRO 100, HYDRO 186, HYDRO 3488, HYDRO 70, HYDRO 84, HYDRO 86. (Item #: 108550, Ref: 68837C3) $8.80
Taper Roller Bearing - Measuring; Width - 0.548 inches, Inside Diameter - 3.740 inches, Outside Diameter - 5.315 inches, this bearing is used in ZF Axles on tractors with mechanical four wheel drive. This bearing also has other applications. Replaces OEM numbers: ZP0750117062, 5136951, 83946047, 81312C1, 83927807, 47539809, 1-31-741-019, 05136951, 85136951, 85806002, 1966169C1, CAR118378, 83983456, AL38099, RE45944, 819310, 819349/819310, 819349 (Item #: 156177, Ref: ZP0750117062) $86.82
Tie Rod Assembly - This Tie Rod Assembly is used on Adjustable Straight Axles (52 Inches to 82 Inches Tread Width). It Replaces 3125171R2, 3125171R3, 1332805C2, 3116406R3, 3116406R4, 3116406R5, 3116321R93, 1538016C1. (Item #: 156878, Ref: 1538016C1) $127.00
Tie Rod Clamp - Used on Farmall / IH models, this tie rod clamp fits 574, AV, AV1, A1, CUB, SUPER A, 100, 130, 140, 200, 230, 240, 2400, 248, 2500, 2504, 258, 3230, 340, 385, 404, 4210, 4230, 4240, 454, 474, 484, 485, 504, 584, 585, 595, 674, 684, 685, 695, 784, 884, 885, 995 (Item #: 104368, Ref: 43747D) $17.30
Tie Rod End - The measurements on this Tie Rod End are as follows: 3-3/4 inches from the center of the ball joint to the end of the shaft, 7/8 16 UN RH Thread on shaft. Replaces 1537872C1 (Item #: 123097) $59.00
Tie Rod (Steering Cylinder) - This Tie Rod End is 6.750 from center of ball joint to end of rod. 18mm x 1.5 right hand thread. Replaces CAR48998, 81875595, 81878543, 1537612C1, 137048A1 (Item #: 104374, Ref: CAR48998) $89.00

Wheels
Front Wheel Hub, Heavy Duty - 6 bolt. For tractor models 268, 278, 3230, 4210, 4230, 4240, 574, 584, 585, 595, 595XL, 684, 685, 685XL, 695, 695XL, 784, 785, 884, 885, 885XL, 895, 895XL, 995, C100, C70, C80, C90, CX100, CX70, CX80, CX90, Hydro 84. (Item #: 124067, Ref: 67527C91) $137.00
Hub Cap - This Hub Cap is used with hubs: 67527C91, 406294R21, 406292R11, 536058R11. It is 2.5 inches in diameter. It replaces 612884R1, 47468696. (Item #: 115100, Ref: 612884R1) $5.10
Wheel Hub, Front - Used on IH models 238, 248, 258, 268, 288, 3210, 3220, 3230, 385, 395, 4210, 4220, 4230, 4240, 454, 475, 484, 485, 485XL, 495, 495XL, 574, 584, 585, 585XL, 595, 595XL, 674, 684, 685, 685XL, 695, 695XL, 784, 785, 785XL, 795, 884, 885, 885XL, 895, 895XL, 995, C100, C50, C60, C70, C80, C90, CX100, CX50, CX60, CX70, CX80, CX90, Hydro 84, Hydro 86, MX100C, MX80C, MX90C this Front Hub replaces OEM number 67527C92, 67527C91. Uses Wheel Bearing Kit WBKIH6 (Item #: 124067, Ref: 67527C92) $137.00
Universal Parts and Accessories Category: Accessories / Supplies

Accessories / Supplies
Auxiliary Heater, Universal - This universal auxiliary heater is used for tractor cabs, combines, backhoes, dozers, forklifts, etc. using 5/8 inch heater hose connections. Hot water forced air heat. Dimensions: 6-1/2 inches x 9-1/2 inches x 9 inches, steel powder coat housing with aluminum core. 3-speed high volume squirrel cage fan, 12-volt, 20, 000 BTU includes switch, brackets, instructions. (Item #: 182644, Ref: MIS3127) $385.00
Magnetic Block Heater - Universal. Magnetic utility heater. 120 volt AC, 200 Watts. Built-in thermostat maintains optimum temperature - will not exceed 250 degree F (121 degree C). Quick-grip handle protects hands from heat. 4-3/8 inches (11cm) length, 2-1/2 inches (6.3cm) width, 3 inches (7.5cm) height (including handle). (Item #: 178758, Ref: MBH1153) $97.00

Decals and Emblems
Decal, Fear This IH - Black and red, 12-1/2 x 3-3/4. For all Models. (Item #: 183484, Ref: S.67826) $15.80
Decal, IH Block - "IH" logo, 11 inches. (Item #: 183564, Ref: R4682) $17.40
Decal, IH Block - "IH", 3 inch x 3 1/4 inch Block. (Item #: 101094, Ref: R4681) $6.40
Decal, IH Block - "IH" logo, 1 3/4 inch. (Item #: 183266, Ref: R4680) $5.00
Decal, IH Block - "IH", 1 1/4 inch Logo . (Item #: 183058, Ref: R4679) $3.90
Decal, IH Block - "IH" logo, 7 inches printed on vinyl. (Item #: 183292, Ref: R5171) $25.80
Decal, IH Block - "IH" logo, 8 inches printed on vinyl. (Item #: 183123, Ref: R5172) $30.50
Decal, IH Block - "IH" logo, 10 inches. (Item #: 183276, Ref: R5173) $36.60
Decal, IH Block - "IH" logo no background, 1 inch printed on vinyl. (Item #: 183334, Ref: R5174) $2.60
Decal, IH Block - "IH" logo no background, 1-5/8 inches printed on vinyl. (Item #: 183338, Ref: R5175) $3.90
Decal, IH Block - "IH" logo no background, 2 inches x 2-1/2 inch printed on vinyl. (Item #: 183347, Ref: R5176) $5.00
Decal, IH Block - "IH" logo no background, 3 inch x 3-1/2 inch printed on vinyl. (Item #: 183352, Ref: R5177) $14.20
Decal, IH Block - "IH" logo no background, 4-1/2 inch x 4-3/4 inch printed on vinyl. (Item #: 183255, Ref: R5178) $7.50
Decal, IH Block - "IH" logo no background, 5-1/2" x 6" printed on vinyl. (Item #: 183265, Ref: R5179) $16.60
Decal, IH Block - "IH" logo no background, 6-1/2 inch x 7 inch. (Item #: 183547, Ref: R5180) $12.40
Decal, IH Block - "IH" logo no background, 7-1/2 inch x 8 inch. (Item #: 183556, Ref: R5181) $14.80
Decal, IH Block - "IH" logo on silver background, 2 inch x 2-1/4 inch. (Item #: 183560, Ref: R5182) $14.20
Decal, IH Block - "IH" logo no background, 10 inch x 11 inch. (Item #: 183543, Ref: R5183) $25.50
International Decal - 8-1/2 inch long, white with black outline. (Item #: 183068, Ref: R0679) $9.40
International Decal - 23 inches long, black block letters. (Item #: 183477, Ref: R0680) $12.40
International Decal - 23 inches long, white with black outline. (Item #: 183478, Ref: R0681) $16.60
International Decal - 26 inches long, black block letters. (Item #: 183481, Ref: R0682) $14.80
International Decal - 26 inches long, white with black outline. (Item #: 101032, Ref: R0683) $14.00
International Decal - 29 inches long, black block letters. (Item #: 101030, Ref: R0684) $10.50
International Decal - 29 inches long, white with black outline. (Item #: 101033, Ref: R0685) $17.50

Electrical System
NOTE Alternator - Don't see the Alternator you need for your tractor? We have many alternators not listed on this website (for tractors 1953 and newer). Just call us at 800-853-2651.	NOTE
No Picture Alternator, 12 Volt - Universal 63 Amp Delco Alternator. Single wire with built in regulator. Will fit most tractors pre 1980. (Item #: 111377, Ref: 8NE10305SE) $96.00
Alternator Conversion Plug - Used to turn Delco SI Style 2-Wire plug alternators into self-exciting style. (Item #: 178026, Ref: ADR9209) $14.40
Alternator Top Adjusting Bracket, Universal - Universal Top Adjusting Bracket for Alternator or Generator is 7/8 inches wide, 1-1/2 inch offset, 8-1/4 inch from farthest end of slot to center of mounting hole, 3-3/4 inch slot length, 3/8 inch mounting hole. (Item #: 173326, Ref: 8NL10302) $25.20
No Picture Battery Thermal Wrap - 60 Watt, 28 inches long wrap to keep your battery warm. (Item #: BTW28) $35.98
No Picture Battery Thermal Wrap - 160 Watt, 36 inches long wrap to keep your battery warm. (Item #: BTW72) $53.81
No Picture Coil - This universal automotive style coil is 28, 000 volts for a 12 volt system, 2.9 ohms. Measures 6 inches long and 2 1/2 inches diameter. (Item #: 182583, Ref: 28010) $49.20
Distributor Cap, WICO - For All Models with WICO distributor having clip type cap with 3 3/8 inside diameter seat. (Item #: 108299, Ref: X30042) $62.15
Magneto, Wico XH and XHD, Service and Parts Manual - Wico XH And XHD magneto service instructions and parts list. This is a reprint of the original manual that has exploded views of all parts on the tractor with numbered pictures giving great detail on assembly and disassembly. It also gives you a guide with numbers for ordering parts. (Item #: 182504, Ref: MAG6) $19.20
No Picture Spark Plug - Extended tip, 14mm thread, 3/8 inch reach. Replaces Champion J10Y, J11Y, J12Y, J13Y. NOTE: Verify spark plug type before ordering. (Item #: 179437, Ref: AL85) $5.60
Spark Plug - Standard tip, 14mm thread, .472" reach. Replaces Champion L9J, L10, L86, L86C, L88A, L90. NOTE: Verify spark plug type before ordering. (Item #: 182459, Ref: AL425) $4.80
NOTE Starter - Don't see the starter you need for your tractor? We probably have it! Just call us at 800-853-2651 with your make, model, engine cubic inches (CID) and number off your old starter and we will see if we can find it!	NOTE
Starter, Generator, Distributor Tag, 6 Volt, Blank - Comes with 2 rivets. 2.5" long, .800" wide, 2" center to center rivet hole, .150" dia. rivet holes. Customer must stamp numbers. (Item #: 182608, Ref: DELCO6) $16.80
Starter Solenoid - This is a 3 post, 12 volt Starter Solenoid. Can be used as a saddle mount or flat surface mount. May come in a metal or plastic casing. Replaces: 1114200, 1114207, 1114216, 1114225, 1114235, 1114545, 1114548, 1118820, 1996067, D928, DR1467, DR1485. May come in a silver metal casing versus black plastic. (Item #: 150223, Ref: DR1467) $19.20
Tag for Starter/Generator, 12 Volt, Blank - Comes with 2 rivets. 2.5" long, .800" wide, 2" center to center rivet hole, .150" dia. rivet holes. Customer must stamp numbers. (Item #: 182606, Ref: DELCO12) $16.80
Voltage Regulator, 12 Volt - 4-terminal flat mount. The Three Post side of this regulator may be parallel or slightly splayed. Fits most 12V tractors and combines prior to 1957. (Item #: 105581, Ref: 182548M92) $25.00

Engine Gaskets
Silicone Blue RTV - Permatex ultra blue, no leak RTV silicone gasket, oil resistant, use on valve covers, oil pans, timing covers, water pumps. Temperature range -75 degree F to +500 degree F, 3.35 ounce tube. (Item #: 178141, Ref: PRM77BR) $10.90

Exhaust System
Chrome Exhaust Stack - Single Wall, 48 inches long with a slotted, 2 inch inside diameter inlet. This is a universal part. Verify Measurements before ordering. (Item #: 118823, Ref: ZNL89020C) $81.00
Chrome Exhaust Stack - Single Wall, 48 inches long with a slotted, 2.5 inch inside diameter inlet. This is a universal part. Verify Measurements before ordering. (Item #: 119038, Ref: ZNL89025C) $108.00
Chrome Exhaust Stack - Single Wall, 48 inches long with a slotted, 3.00 inch inside diameter inlet. This is a universal part. Verify Measurements before ordering. (Item #: 114858, Ref: ZNL89051C) $135.00
Chrome Exhaust Stack - Single wall, 53 inches long with a slotted, 3.00 inch inside diameter inlet with extended curve. This is a universal part. Verify measurements before ordering. (Item #: 173286, Ref: 146520CHR) $106.00
Chrome Exhaust Stack - Single wall, 53 inches long with a slotted, 3.50 inch inside diameter inlet. It has an extended curve on the outlet. This is a universal part. Verify measurements before ordering. (Item #: 173287, Ref: 146490CHR) $161.00
Chrome Exhaust Stack - Single Wall, 48 inches long with a slotted, 4.00 inch inside diameter inlet. This is a universal part. Verify Measurements before ordering. (Item #: 114945, Ref: ZNL89057C) $145.00
Chrome Exhaust Stack - Single Wall, 48 inches long with a slotted, 5.00 inch inside diameter inlet. This is a universal part. Verify Measurements before ordering. (Item #: 119080, Ref: ZNL89485C) $174.00
Chrome Exhaust Stack - Single Wall, 42 inches long with a slotted, 2.50 inch inside diameter inlet. This is a universal part. Verify Measurements before ordering. (Item #: 173281, Ref: L102236CHR) $88.00
Muffler Clamp, 1-1/4 - New Clamp for 1-1/4 inch outside diameter muffler inlet. (Item #: 182682, Ref: MC114) $2.10
Muffler Clamp, 1-3/4 - New Clamp for 1-3/4 inch outside diameter muffler inlet. (Item #: 108866, Ref: MC134) $4.80
Muffler Clamp, 1-3/8 - New Clamp for 1-3/8 inch outside diameter muffler inlet. (Item #: 182687, Ref: MC138) $2.90
Muffler Clamp, 2-1/4 - New Clamp for 2-1/4 inch outside diameter muffler inlet. (Item #: 108870, Ref: MC214) $5.30
Muffler Clamp, 2-3/4 - New Clamp for 2-3/4 inch outside diameter muffler inlet. (Item #: 108872, Ref: MC234) $8.71
Muffler Clamp, 3 - New Clamp for 3 inch outside diameter muffler inlet. (Item #: 108873, Ref: MC300) $7.40
Muffler Clamp, 3-1/2 - New Clamp for 3-1/2 inch outside diameter muffler inlet. (Item #: 108874, Ref: MC312) $8.00
Muffler Clamp, 4 - New Clamp for 4 inch outside diameter muffler inlet. (Item #: 108875, Ref: MC400) $8.30
Muffler Clamp, 5 - New Clamp for 5 inch outside diameter muffler inlet. (Item #: 118841, Ref: MC500) $12.70
Rain Cap - This rain cap is for a 1.750 inch pipe. (Item #: 108632, Ref: R1799) $11.00
Rain Cap - This rain cap is for a 2.0 inch pipe. (Item #: 108633, Ref: R1800) $8.80
Rain Cap - This rain cap is for a 2.50 inch pipe. (Item #: 108635, Ref: R1802) $12.50
Rain Cap - This rain cap is for a 2.750 inch pipe. (Item #: 108636, Ref: R1804) $11.08
Rain Cap - This rain cap is for a 4.0 inch pipe. (Item #: 108645, Ref: R1807) $12.90
Rain Cap - This rain cap is for a 4.50 inch pipe. (Item #: 108749, Ref: WC14) $13.40
Rain Cap - This rain cap is for a 5.0 inch pipe. (Item #: 108750, Ref: WC15) $17.40
Stainless Steel Clamp, 2.75 Inch - This Stainless Steel Clamp is used with Chrome Stacks and in other applications. (Item #: 179749, Ref: ZNL90872A) $6.50
Stainless Steel Clamp, 4 Inch - This Stainless Steel Clamp is used with Chrome Stacks and in other applications. (Item #: 185428, Ref: ZNL90875A) $8.50

Fuel System / Air Intake
Air Cleaner Filler - Fits many air cleaners that use steel wool type filler. Custom manufactured mesh. 1 bag = 3-1/2 inch x 3-1/4 inch. (Item #: 151026, Ref: S.43231) $14.00
Fuel Tank Screen - This Fuel Tank Screen is used with most stem-type sediment bowls to further protect against debris in the gas line. It has a 0.216 inch Insert Pipe outside diameter - 2.53 inch Overall Length. (Item #: 114940, Ref: R7949) $9.92
Main Fuel Valve - This main fuel valve replaces the original fuel solenoid for International carburetors. The original fuel solenoids are very unreliable and can easily be replaced with this manual valve. This assembly contains: the valve, graphite packing, and packing nut. Used on Carburetors: 50981DC, 45108DB, 50983DC, 52814DA, 47387DC, 361525R92, 358065R92, 362173R92, 367259R92, 380956R91, 380956R92, 380956R93, 381983R91, 381984R95, 389511R92, 367258R92, 396966R91, 388296R91, 388424R96, 396197R96, 396198R92, 381419R91, 397224R93, 381420R91, 357231R91, 356948R92. Replaces 47404DA, 374327R1, 362526R1, 362525R1 (Item #: 117537, Ref: 47404DASSY) $30.10
Sediment Bowl Gasket, 2-1/8 inch - For bowls with 2-1/8 inch diameter, 2.150 inch outside diameter. Made in the USA. (Item #: 112364, Ref: C1778R) $3.30

Gauges
No Picture Amp Gauge - This amp gauge comes with the "IH" logo printed on the face. It has a black face, chrome bezel, and reads 60-0-60. (Item #: 178963, Ref: IHS1837) $30.00
No Picture Hourmeter - DC voltages from 12 volt thru 36 volt nominal. Heavy duty glass-reinforced polyester body. Internal shock shields and grommets protect movement from shock and vibration damage. Fits 2-1/4 inch opening, three (3) mounting screws with nuts and two (2) blade terminals included. (Item #: 178318, Ref: HM771) $63.00
Hourmeter, Analog - 2 inch, black. Can be used on any tractor with a 12 to 24 volt electrical system. (Item #: 178285, Ref: S.52672) $42.30
Oil Gauge - For IHC and Farmall tractors 1947 and and up. Oil Pressure Gauge with color band - Includes mounting bracket. Has IH logo on face. (Item #: 110849, Ref: 41934DB) $49.57
Oil Line Adapter - Oil Gauge fittings may be different even for the same models. Here is an Oil Line Adapter if you have a gauge line without removable fittings, this converts 1/8 inch pipe thread to 1/8 inch tube. Brass. (Item #: 179540, Ref: 919095) $16.00

Hitch / Drawbar
Conversion Tong - Two Point Conversion Tong straight left hand Tong with combination Cat. I and Cat. II Ball. For converting IHC Two Point Fast Hitch to Three Point. About 28 inches overall length. (Item #: 184153, Ref: FH1447) $364.00
Conversion Tong - Two Point Conversion Tong straight right hand Tong with combination Cat. I and Cat. II Ball. For converting IHC Two Point Fast Hitch to Three Point. About 28 inches overall length. (Item #: 184167, Ref: FH1448) $364.00
Conversion Tong - Two Point Conversion Tong bent type, and Cat. II Ball. Left Hand. For converting IHC Two Point Fast Hitch to Three Point. About 32 inches overall length. (Item #: 179611, Ref: FH14416) $439.00
Conversion Tong - Two Point Conversion Tong bent type, right hand Tong with combination Cat. I and Cat. II Ball. Right Hand. The Bent Type spaces out at 32 inches between the ends of the tongs. The Non-Bent Type spaces out at 26 inches between the ends of the tongs. For converting IHC Two Point Fast Hitch to Three Point. About 32 inches overall length. (Item #: 179008, Ref: FH14417) $439.00
Hair Pin Assortment - 15-piece assortment. Includes four (4) of HP-3 (wire diameter 3/16 inch, length 3.75 inch), four (4) of HP-4 (wire diameter 5/32 inch, length 2 15/16 inches), four (4) of HP-5 (wire diameter 1/8 inch, length 2 9/16 inches), and three (3) of HP-6 (wire diameter 3/32 inch, length 1 5/8 inches). (Item #: 182461, Ref: HPA15X) $12.17
Universal Drawbar Lock - For Cat. 1 drawbars up to 1 1/2 inch thick and 3 inches wide. Prevents drawbar from rotating. (Item #: 112156, Ref: DBL2) $37.00

Hydraulic System
Filter Element - 25 Micron replacement element for SF1-25. (Item #: 182541, Ref: 1A9023) $15.40
Filter Element - 10 Micron replacement element for SF1-10. (Item #: 120092, Ref: 1A9021) $13.60
Hydraulic Hose Assembly-NPT, 12 inch - Universal. 12 inch overall length. 1/2 I.D. 2 Wire. Solid Male 1/2 NPT thread on both ends. (Item #: 118257, Ref: H42-2M-12) $11.00
Hydraulic Hose Assembly-NPT, 180 inch - Universal. 180 inch (15 Feet) overall length. 1/2 inch inside diameter. 2 Wire. Solid Male 1/2 inch NPT thread on both ends. (Item #: 179906, Ref: H42-2M-180) $55.50
Hydraulic Hose Assembly-NPT, 24 inch - Universal. 1/2 inch I.D. double wire braid (SAE-2R) with 1/2 inch NPT solid male fittings both ends. 24 inch overall length. Replaces OEM # - 407435R1. (Item #: 118256, Ref: H42-2M-24) $14.10
Hydraulic Hose Assembly-NPT, 30 inch - Universal. 30 inch overall length. 1/2 I.D. 2 Wire. Solid Male 1/2 NPT thread on both ends. (Item #: 118259, Ref: H42-2M-30) $16.10
Hydraulic Hose Assembly-NPT, 48 inch - Universal. I.H.C.: 1/2" I.D. double wire braid (SAE-2R) with 1/2" NPT solid male fittings both ends. 48" overall length. Replaces OEM # - 407437R1. Hydraulics: 48 inch overall length (Item #: 118261, Ref: H42-2M-48) $16.50
Universal Pressure Gauge, Hydraulic - 1000 Lb. Gauge. Glycerin Filled. Stainless Steel Case 2-1 2 diameter. Nickel silver movement accurate to within 2%. Dual range KPA-PSI. Plexiglass crystal. 1 4 NPT male brass fitting. (Item #: 172285, Ref: GG1000) $13.50
Universal Pressure Gauge, Hydraulic - 60lb Gauge. Glycerin Filled. Stainless Steel Case 2-1/2 diameter. Nickel silver movement accurate to within 2%. Dual range KPA-PSI. Plexiglass crystal. 1/4 NPT male brass fitting. (Item #: 172338, Ref: GG60) $13.91

Implements
Axle Bolt - Axle bolt, 1 each (Ref 3). Used on many Bush Hog rotary cutters. Used on models 12, 104, 105, 109, 126, 205, 255, 275, 285, 305, 306, 307, 405, 405HR, 406, 406HR, 502, 600, 1050, 1051, 1109, 1126, 1207, 1209, 1226, 1306, 1307, 1405, 1406, 2510, 2512, 3108, 2309, BD90, FH162, S268, SM60, SQ36 (Item #: 170217, Ref: BH1317) $14.90
Axle Bolt - Axle bolt, 1 each (Ref 3). Used on many Bush Hog rotary cutters. Used on models 12, 104, 105, 109, 126, 205, 255, 275, 285, 305, 306, 307, 405, 405HR, 406, 406HR, 502, 600, 1050, 1051, 1109, 1126, 1207, 1209, 1226, 1306, 1307, 1405, 1406, 2510, 2512, 3108, 2309, BD90, FH162, S268, SM60, SQ36 (Item #: 170217, Ref: BH1317) $14.90
Bearing cone (L44643) - For Caster Assembly, requires 2.Used on many Bush Hog rotary cutters. Used on models 12, 104, 105, 109, 126, 205, 255, 275, 285, 305, 306, 307, 405, 405HR, 406, 406HR, 502, 600, 1050, 1051, 1109, 1126, 1207, 1209, 1226, 1306, 1307, 1405, 1406, 2510, 2512, 3108, 2309, BD90, FH162, S268, SM60, SQ36, SQ480, SQ600. (Item #: 114630, Ref: 22) $5.90
Bearing Cup - This part fits Caster Assembly (Part Number BH215, Ref #6). Sold individually, two used per caster assembly. Used on many Bush Hog rotary cutters. Used on models 12, 104, 105, 109, 126, 205, 255, 275, 285, 305, 306, 307, 405, 405HR, 406, 406HR, 502, 600, 1050, 1051, 1109, 1126, 1207, 1209, 1226, 1306, 1307, 1405, 1406, 2510, 2512, 3108, 2309, BD90, FH162, S268, SM60, SQ36. Also replaces 132709, 15191, 32190M1, L44610. (Item #: 169771, Ref: 170BH) $7.86
Caster Assembly - Tail wheel and hub assembly with grease fitting and fork assembly. Shaft on Yoke is 1-1/2 inches diameter, 8 inches overall length, 7-1/4 inch to pin hole. New style tail assembly, used on the following Bush Hog cutters: 12, 104, 105, 109, 126, 205, 255, 275, 285, 305, 306, 307, 405, 405HR, 406, 406HR, 502, 600, 1050, 1051, 1109, 1126, 1207, 1209, 1226, 1306, 1307, 1405. Wheel must be attached to fork. For Bush Hog cutters with SPB40 spacer (included), assembly will also replace all models with Timken bearings. (Item #: 173612, Ref: 12269) $183.00
Caster Assembly, Old Style - Tail Wheel and Hub Assembly with grease fitting. 4 x 8 inch rim, 15 inch outside diameter of wheel. Includes wheel, hub, axle bearing and bolt assembly. OLD style tail assembly used on the following Bush Hog cutters: 12, 104, 105, 109, 126, 205, 255, 275, 285, 305, 306, 307, 405, 405HR, 406, 406HR, 502, 600, 1050, 1051, 1109, 1126, 1207, 1209, 1226, 1306, 1307, 1405, 1406, 2510, 2512, 3108, 2309, BD90, FH162, S268, SM60, SQ36, SQ480, SQ600. Wheel must be attached to fork. For Bush Hog cutters. With SPB40 spacer, assembly will also replace all models with Timken Bearings (Ref #1-#11). (Item #: 161111, Ref: BH215) $132.00
Hub Assembly - Hub with bushings (3/4 inch), wheel bolts (4), and grease fitting. Center tube length 5 inches. For rotary cutters: RB60 with new style 1-1/4 inch diameter caster, SM60R, SM160R; Squealer models: 1207, SQ36, SQ48, SQ60, SQ72, SQ148, SQ480. Replaces 60978, 60990, 63812. Can use 500BH tail wheel. (Item #: 180514, Ref: 63813BH) $38.10
Hub with Bearing Cups - 4-bolt, 5 inch bolt circle and 3-5/8 inch wheel pivot hub with bearing cups (1 inch axle) (Ref #5). This part fits caster assembly (part number BH215). Used on many Bush Hog rotary cutters. Used on models 12, 104, 105, 109, 126, 205, 255, 275, 285, 305, 306, 307, 405, 405HR, 406, 406HR, 502, 600, 1050, 1051, 1109, 1126, 1207, 1209, 1226, 1306, 1307, 1405, 1406, 2510, 2512, 3108, 2309, BD90, FH162, S268, SM60, SQ36. (Item #: 182627, Ref: BH1311) $49.30
No Picture Round Bale Tine 31.5 Inches - Fully Hardened. Also replaces Kverneland 221151. (Item #: 182589, Ref: 221129) $51.00
No Picture Round Bale Tine 31.5 Inches - Fully Hardened. Also replaces Kverneland 221151. (Item #: 182589, Ref: 221129) $51.00
No Picture Round Bale Tine 38.5 Inches - Fully Hardened. Also replaces Kverneland 241107, 241161. (Item #: 182592, Ref: 241100) $91.48
No Picture Round Bale Tine 43 Inches - Fully Hardened. (Item #: 182594, Ref: 241166) $111.54
No Picture Round Bale Tine 49 Inches - Fully Hardened. (Item #: 152690, Ref: 241162) $78.00
No Picture Round Bale Tine 55 Inches - Fully Hardened. (Item #: 182593, Ref: 241163) $131.61
Seal, Caster - Seal, 2 required (Ref #2). Used on many Bush Hog rotary cutters. Used on models 12, 104, 105, 109, 126, 205, 255, 275, 285, 305, 306, 307, 405, 405HR, 406, 406HR, 502, 600, 1050, 1051, 1109, 1126, 1207, 1209, 1226, 1306, 1307, 1405, 1406, 2510, 2512, 3108, 2309, BD90, FH162, S268, SM60, SQ36, SQ480, SQ600. (Item #: 180300, Ref: 30BH) $4.30
Tail Wheel Assembly - 4 inch x 8 inch tail wheel assembly with laminated tire. 3-5/8 inch pilot, 4 bolt holes, 5 inch bolt circle, 3-3/4 inches wide, 15 inch outside diameter. Used on the following Bush Hog cutters: 12, 104, 105, 109, 126, 205, 255, 275, 285, 305, 306, 307, 405, 405HR, 406, 406HR, 502, 600, 1050, 1051, 1109, 1126, 1207, 1209, 1226, 1306, 1307, 1405 and 1406, 2510, 2512, 3108, 3209, BD90, FH162, S268, SM60, SQ36, SQ480, SQ600. Replaces Sidewinder 15205, Servis Rhino 373024H, Terrain King 373024H, Modern 401-0048, BMB 5337, Hardee C40-RC, King Kutter KK4X8. (Item #: 111222, Ref: 500BH) $56.00
No Picture Talc Powder Lubricant - Dry Talc powder lubricant, 8 lb container. Absorbs moisture and keeps treated seed from sticking together in planter boxes. Recommended application rate: 3 oz. Coverage: Typically treats 60-80 acres. (Item #: 107928, Ref: TP19000TP) $22.10

Lights
Headlight Assembly, Teardrop- 12 Volt - Original Style, TEAR-DROP shaped back. PAINTED RED. 12-VOLTS. Approx 5" diameter. Price is for one complete headlamp assembly. Original replacement for many IH tractors. Verify your configuration (Teardrop vs. Flat-Back) before ordering. (Item #: 112414, Ref: 45640DB-12V) $43.10
Headlight Assembly, Teardrop - 6 Volt - Original Style, TEAR-DROP shaped back. PAINTED RED. 6-VOLTS. Approx 5" diameter. Price is for one complete headlamp assembly. Original replacement for many IH tractors. Verify your configuration (Teardrop vs. Flat-Back) before ordering. (Item #: 112415, Ref: 45640DB) $42.80
Light Bulb, Sealed Beam, 6 Volt - 4-1/2 inch number 4511. (Item #: 111227, Ref: 373661R91) $13.50
Portable Halogen Work Lamp - 3 inch x 5 inch sealed beam unit, 12 volt, 50 watt, 4 amp. With handle and magnetic base. Projects flood beam pattern 50 foot wide x 30 foot long. Lamp is not legal for street use. (Item #: L200MAGH) $75.13
No Picture Sealed Beam Light - 6 Volt (Item #: 111938, Ref: R2712) $46.30
No Picture Sealed Beam Light - 12 Volt (Item #: 122080, Ref: R2713) $36.00
Switch, Light, with Knob - Universal switch, for 6 volt tractors. Verify style is correct for your model. (Item #: 114720, Ref: AA4667R) $16.60
Work Light 12V - Universal Work light is 12 volt, 3000 candle power, and a trapezoidal light pattern. I does swivel up and down, not side-to-side. Comes with 4-1/2" diameter sealed beam lamp, part number L4411. Does not have a switch on the back. (Item #: 173803, Ref: L408-12V) $38.40

Miscellaneous
Cab Foam Kit - With Headliner 10-Piece - Black For tractor models with QT1 Year Round Cab. Must be truck shipped - $75 will be added for shipping due to weight and size. (Item #: 186987, Ref: R1236) $389.00
Deluxe Canopy, 3 Bow - This universal Blue 3-Bow Deluxe Canopy comes with bows and cover. Universal brackets sold separately. Fender mounting kit is part number 6A216. Axle Mounting Kit is part number 6A217. Measures about 48 inch spread from Mounting brackets (40 inch spread at the top of canopy) Height is approximately 31 inch. (Item #: 178876, Ref: RFC100B) $245.00
Hand Cleaner, Gallon - Hand cleaner, with dispenser pump. 1 gallon plastic bottle. (Item #: 180453, Ref: PRM25218) $24.60
Tractor Umbrella with Frame & Mounting Bracket - Red - Complete umbrella consisting of a cover, bracket and frame, 54" x 54" cover made of 10 oz. duck canvas with leather reinforcements and steel grommets, Metal parts are zinc-coated for long-lasting, maintenance-free service, Rigid framework for cover is built to withstand farm and industrial use, Installs easily, folds down for trailering and removes in seconds without tools, (Item #: 161193) $123.00

Paint
44 Minute DVD - How to Paint a Tractor - This DVD demonstrates the entire painting process including sanding, priming, body work, painting and decals. A John Deere B is used as the sample tractor, but the information will pertain to any make or model - the techniques are the same. Safety is also discussed. (Item #: 183950, Ref: JDV-02250) $24.00
No Picture Paint, Aluminum High Heat Spray Can - 12 oz. spray can. Withstands heat up to 650 degrees for use on stacks and mufflers. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100244, Ref: TP402HHSP_) $8.50
No Picture Paint, Aluminum, Spray Can - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100244, Ref: TP312SP) $8.50
No Picture Paint, Clear Coat, 1 Gallon - High strength air dry Acrylic laquer. Protects the original paint finish, adds more shine, prolongs color and prevents fade. Water clear non-yellowing gloss coat, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 108409, Ref: TP447GAL) $65.00
No Picture Paint, Clear Coat, 1 Quart - From Tallmans, formulated by Van Sickle, providing OEM quality. High strength air dry Acrylic laquer. Protects the original paint finish, adds more shine, prolongs color and prevents fade. Water clear non-yellowing gloss coat, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 108408, Ref: TP447QT) $30.00
No Picture Paint, Farmall Red, 1 Gallon - This "Farmall" Red is for those models that were manufactured under the earlier FARMALL Brand (Not International). From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 101108, Ref: TP110GAL) $55.00
No Picture Paint, Farmall Red, 1 Quart - This "Farmall" Red is for those models that were manufactured under the earlier FARMALL Brand (Not International). From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 101107, Ref: TP110QT) $24.60
No Picture Paint, Farmall Red, Spray Can - This "Farmall" Red is for those models that were manufactured under the earlier FARMALL Brand (Not International). From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100720, Ref: TP110SP) $8.50
No Picture Paint, Gloss Black, 1 Gallon - High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100116, Ref: TP550GAL) $53.00
No Picture Paint, Gloss Black, 1 Quart - High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100115, Ref: TP550QT) $24.00
No Picture Paint, Gloss Black, Spray Can - High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100114, Ref: TP550SP) $8.70
No Picture Paint, Gray Primer, 1 Quart - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100121, Ref: TP2700QT) $22.40
No Picture Paint, Gray Primer, Spray Can - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. (Item #: 100120, Ref: TP2700SP) $8.30
No Picture Paint, IH Blue, 1 Gallon - High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 101114, Ref: TP910GAL) $58.00
No Picture Paint, IH Blue, 1 Quart - High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 101113, Ref: TP910QT) $24.00
No Picture Paint, IH Blue, Spray Can - High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 101112, Ref: TP910SP) $8.60
No Picture Paint, IH Red, 1 Gallon - This "IH" Red is for those models that were manufactured under the INTERNATIONAL Brand (Not Farmall). High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100722, Ref: TP905GAL) $56.00
No Picture Paint, IH Red, 1 Quart - This "IH" Red is for those models that were manufactured under the INTERNATIONAL Brand (Not Farmall). High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics.Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100721, Ref: TP905QT) $24.00
No Picture Paint, IH Red, Spray Can - This "IH" Red is for those models that were manufactured under the INTERNATIONAL Brand (Not Farmall). High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics.Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100720, Ref: TP905SP) $8.50
No Picture Paint, McCormick Deering Gray, 1 Gallon - High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 108401, Ref: TP450GAL) $90.00
No Picture Paint, McCormick Deering Gray, 1 Quart - High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 108400, Ref: TP450QT) $35.00
No Picture Paint, McCormick Deering Gray, Spray Can - High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 108399, Ref: TP450SP) $11.00
No Picture Paint, Off White, 1 Gallon - High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 101117, Ref: TP900GAL) $62.00
No Picture Paint, Off White, 1 Quart - High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 101116, Ref: TP900QT) $24.90
No Picture Paint, Off White, Spray Can - High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 101115, Ref: TP900SP) $8.20
No Picture Paint, Red Primer, 1 Gallon - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100119, Ref: TP3987GAL) $59.00
No Picture Paint, Red Primer, 1 Quart - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100118, Ref: TP3987QT) $24.00
No Picture Paint, Satin Black, 1 Quart - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics.Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100254, Ref: TP225QT) $24.00
No Picture Paint, Satin Black, Spray Can - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics.Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100253, Ref: TP225SP) $8.50
No Picture Paint, Universal Non Glare Black, 1 Quart - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100254, Ref: TP120QT) $24.00
No Picture Paint, Universal, Non Glare Black, Spray Can - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100253, Ref: TP120SP) $8.50
No Picture Paint, Yellow Primer, 1 Gallon - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 184741, Ref: TP2720GAL) $84.67
No Picture Slip Resistant Coating - Gallon can. For use in a variety of applications where slip resistance or sound deadening qualities are desired. Moisture and chemical resistant, helps protect against corrosion. Ready to use as is for easy application and touch up with brush or roller. Coverage area is 75 to 100 square feet. (Item #: BL116GAL) $68.39
No Picture Slip Resistant Coating Kit - Do it yourself kit. Comes with one gallon of liner, mini roller with tray, two replacement roller covers, 2" brush, and sanding sponge. For use in a variety of applications where slip resistance or sound deadening qualities are desired. Moisture and chemical resistant, helps protect against corrosion. Ready to use as is for easy application and touch up with brush or roller. Coverage area is 75 to 100 square feet. (Item #: BL116KIT) $99.22
Tire Paint, Black - Black tire paint (1 Gallon)- The best way to make tires look like new. Our paint is a permanent water based paint that applies easily and dries quickly. It will not rub off even when wet. Gives dull, faded tires a non-glossy, like new finish. This paint is READY TO USE. (Item #: 185598, Ref: E844R) $40.01

PTO / Driveline
Driveline Assembly with Yokes - AB4 series, complete drive shaft assembly with shielding and tractor and implement yokes. 1-3/8 inch 6 spline Q.D. tractor yoke. 1-3/8 inch round bore with 1/2 inch pin hole implement yoke. 1300 mm (51 inch) overall length end of yoke to end of yoke. 1110 mm (43-3/4 inch) compressed length center to center of cross bore. Cross and bearing kit, 27 mm 1.063 (1-1/16 inch) bearing diameter x 74.6 mm 2.940 (2-15/16 inch) overall length (43-3/4 inch). Verify length before ordering. (Item #: 180775, Ref: AB4111WY) $174.00
Driveline Assembly with Yokes - AB4 series, complete drive shaft assembly with shielding and tractor yoke, ratcheting torque limiter on implement end. 1-3/8 inch 6 spline Q.D. tractor yoke, 1-3/8 inch 6 spline ratcheting torque limiter with quick disconnect on implement end. 1372 mm (54 inch) overall length end of yoke to end of clutch. 1110 mm (43-3/4 inch) compressed length center to center of cross bore. Cross and bearing kit 27 mm 1.063 (1-1/16 inch) bearing diameter x 74.6 mm 2.940 (2-15/16 inch). 1372 mm (54 inch) overall length ***VERIFY LENGTH BEFORE ORDERING*** (Item #: 124815, Ref: AB4111K33) $339.00
NOTE PTO Adapter - PTO adapters are located under the PTO category in the Accessories and Universal Parts section.	NOTE
PTO Safety Clutch, 40 HP - 1-3/8 inch 6 spline male and female ends, 6 inch diameter, 40 horse power capacity. Heavy duty unit allows PTO driven implements to freewheel with adjustable safety protection under load. Prevents expensive damage to internal tractor PTO packs. Prevents single clutch tractors from being driven forward by PTO over-run. (Item #: 183648, Ref: B9164) $268.00