Yesterday's Tractor Co. Tractor Parts for All Brands
Click Here or call 800-853-2651 
   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 
Marketplace
Classified Ads
Photo Ads

Community
Discussion Forums
Project Journals
Tractor Town
Your Stories
Show & Pull Guide
Events Calendar
Hauling Schedule

Galleries
Tractor Photos
Implement Photos
Vintage Photos
Help Identify
Parts & Pieces
Stuck & Troubled
Vintage Ads
Community Album
Photo Ad Archives

Research & Info
Articles
Tractor Registry
Tip of the Day
Safety Cartoons
Tractor Values
Serial Numbers
Tune-Up Guide
Paint Codes
List Prices
Production Nbrs
Tune-Up Specs
Torque Values
3-Point Specs
Glossary

Miscellaneous
Tractor Games
Just For Kids
Virtual Show
Museum Guide
Memorial Page
Feedback Form

Yesterday's Tractors Facebook Page

Related Sites
Tractor Shed
TractorLinks.com
Ford 8N/9N Club
Today's Tractors
Garden Tractors
Classic Trucks
Kountry Life

Enter your email address to receive our newsletter!

subscribe
unsubscribe
  
Oliver, Cletrac, Co-op & Cockshutt Tractors Discussion Board

Re: 1550 Diesel Intake valve seals??


[ Expand ] [ View Replies ] [ Add a Reply ] [ Return to Forum ]

Posted by Rocko on January 03, 2013 at 10:13:11 from (173.210.157.58):

In Reply to: 1550 Diesel Intake valve seals?? posted by Rocko on January 02, 2013 at 17:26:18:

OK so I did what J suggested. Removed intake as well as valve cover. Appears what problem is is that stud bolts that screw into block is where oil is coming out. Threaded holes go through to oil side of head and bolts are not sealed. Poured oil down one intake valve stem and it filled and started coming out threaded hole.(I had removed all studs at this point.) Obviously no seal at top of valve stem. I wondered if oil was entering cylinder when valve openned, so I turned engine over by hand didn't see oil level inhole change but I was on oppisite side of engine to turn over engine. Pulled fuel shut off and turned engine over with starter. Again didn't seem to change level in hole or oil pouring through rocker arm system for that matter. Every thing moving and looks well lubed but no noticable amount accumulating in 30 sec. or so. So I assuming that if there are seals at the bottem stopping oil from entering cylinders but below thread holes in head although my test was not overly scientific and I could well be wrong. Casting number on head inself is 180402K if thats of any use. Figure to seal studs with some kind of gasket sealer and put her back together as I will need it to feed again tommorow. Would still appreiciate any further input from you more knowledgable folks out there. Thanks again Rocko.


Replies:




Add a Reply

Name:
E-Mail:
Subject:

Comments:

Optional Link URL:
Link Title:
Optional Image URL:
Optional Video Title:
Optional Video Embed:

Advanced Posting Options

Email Notification: If you check this box, email will be sent to you whenever someone replies to this message. Your email address must be entered above to receive notification. This notification will be cancelled automatically after 2 weeks.



 
Advanced Posting Tools
  Upload Photo  Select Gallery Photo  Attach Serial # List 
Return to Post 
TRACTOR   PARTS TRACTOR   MANUALS
Same-Day Shipping! Most of our stocked parts ship the same day you order (M-F).  Expedited shipping available, just call!  Most prices for parts and manuals are below our competitors.  Compare our super low shipping rates!  We have the parts you need to repair your tractor.  We are a Company you can trust and have generous return policies!   Shop Online Today or call our friendly sales staff toll free (800) 853-2651. [ More Info ]

Home  |  Forums


Copyright © 1997-2014 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters