Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 
Marketplace
Classified Ads
Photo Ads
Tractor Parts
Salvage

Community
Discussion Forums
Project Journals
Your Stories
Events Calendar
Hauling Schedule

Galleries
Tractor Photos
Implement Photos
Vintage Photos
Help Identify
Parts & Pieces
Stuck & Troubled
Vintage Ads
Community Album
Photo Ad Archives

Research & Info
Articles
Tractor Registry
Tip of the Day
Safety Cartoons
Tractor Values
Serial Numbers
Tune-Up Guide
Paint Codes
List Prices
Production Nbrs
Tune-Up Specs
Torque Values
3-Point Specs
Glossary

Miscellaneous
Tractor Games
Just For Kids
Virtual Show
Museum Guide
Memorial Page
Feedback Form

Yesterday's Tractors Facebook Page

  
Ford 9N, 2N & 8N Discussion Board

Re: Bush hog connection


[ View Follow Ups ] [ Post Followup ] [ Return to Forum ]

Posted by Larry 8N75381 on August 17, 2000 at 12:58:14 from (132.250.80.6):

In Reply to: Bush hog connection posted by TimK on August 16, 2000 at 09:12:42:

Gentlemen,

Sorry to be contradictory, BUT which top link rocker hole used is important ONLY for DRAFT loads. You know, stuff that digs in the dirt like a plow, back blade, cultivator and the like. I sure hope you are NOT using your rotorary mower as a draft implement!!

Except for traveling the weight of the mower should be supported only by the lift arms and tail wheel. That is so the mower can dip up and down freely as the tail wheel goes over ground rises or drops into a low spot.

And, even when traveling, the force on the top link rocker is just the OPPOSITE of what a draft implement, like a plow, would put on the rocker. So using the highest position is OK, or any of the others for that matter. I use the higher of the two that are on my Ford 3000 - don't mow with the 8N. I am pretty rough on my mower - like mowing 2" trees. :-) AND I want my Uncle's 8N to survive for my grandson to drive. :-) :-)

As to adjusting the level/height of the mower, the lift arms and tail wheel are the things to adjust. Here is a place where two stops on the quadrant control would be nice. The top one to keep from hitting the front edge of the mower deck with the PTO and a second one a the bottom to set where the mower is level.

I had the same problem with the new adjustable top links that everyone else has. I took the hacksaw to the ridge around the edge. I cut away enough so the one end does not bind (took several cuts), then I cleaned it up with a big file so it looks nice and smooth. You should check the fit and be sure it does not bind when the top link is loose and hanging down against the differential. You will have to put it on ALWAYS the same way - small inconvenience but quite acceptable.

my 2 cents,
Larry


Follow Ups:




Post A Followup

:
:

: Re: Re: Bush hog connection

:

:

:

:

: If you check this box, email will be sent to you whenever someone replies to this message. Your email address must be entered above to receive notification. This notification will be cancelled automatically after 2 weeks.


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Today's Featured Article - Identifying Tractor Noises - by Curtis Von Fange. Listening To Your Tractor : Part 3 - In this series we are continuing to learn the fine art of listening to our tractor in hopes of keeping it running longer. One particularly important facet is to hear and identify the particular noises that our ... [Read Article]

Latest Ad: Super WD9. [More Ads]

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy