Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 
Marketplace
Classified Ads
Photo Ads
Tractor Parts
Salvage

Community
Discussion Forums
Project Journals
Your Stories
Events Calendar
Hauling Schedule

Galleries
Tractor Photos
Implement Photos
Vintage Photos
Help Identify
Parts & Pieces
Stuck & Troubled
Vintage Ads
Community Album
Photo Ad Archives

Research & Info
Articles
Tractor Registry
Tip of the Day
Safety Cartoons
Tractor Values
Serial Numbers
Tune-Up Guide
Paint Codes
List Prices
Production Nbrs
Tune-Up Specs
Torque Values
3-Point Specs
Glossary

Miscellaneous
Tractor Games
Just For Kids
Virtual Show
Museum Guide
Memorial Page
Feedback Form

Yesterday's Tractors Facebook Page

  
Ford Tractors Discussion Board

Re: no hydraulics


[ Expand ] [ View Replies ] [ Add a Reply ] [ Return to Forum ]

Posted by Kurt-NEPA on July 30, 2013 at 03:41:04 from (70.44.176.213):

In Reply to: no hydraulics posted by rhodech on July 29, 2013 at 14:01:22:

Sounds like you have 641D. That helps quite a bit.

Air in the oil causes the bubbles, water causes oil to turn milky.

Have you tried bleeding the pump? It sounds like you have removed the pipe plug from the front of the pump with the tractor running and that is where you saw the oil was full of bubbles and looked milky. Did that help the lift at all?

One thing to try, its requires about $20 in fittings. With the tractor off, remove the bleeder plug from the front of the piston pump. The get some pipe fittings. from the plug hole insert a short nipple, an elbow, a longer nipple, then a ball valve, and finally a hose barb. From the hose barb run a piece of clear plastic hose back to the hydraulic fill port under the seat. Insert the hose.

Once everything is installed and tight, close the valve and start the tractor. Now slowly open the valve. You should see oil flowing through the tube and back into the sump. If it is clear your pump is OK, if it is full of bubbles, let it run for a while, it may clear up. Then close the valve and see if the lift works.

My guess is that you will see bubbles and that this gets the lift going. If yes, and you let the tractor sit overnight, you will loose the lift again. This is a sign of a leaking wobble shaft seal in pump. We'll cross that bridge when we get to it.


Replies:




Add a Reply

:
:
: :

:

:

:

:

:

: If you check this box, email will be sent to you whenever someone replies to this message. Your email address must be entered above to receive notification. This notification will be cancelled automatically after 2 weeks.


 
Advanced Posting Tools
  Upload Photo  Select Gallery Photo  Attach Serial # List 
Return to Post 

TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Today's Featured Article - What Oil Should I Use? - by Francis Robinson. I keep seein this question pop up over and over again in discussion groups all over the web. As with many things there are often several right answers and a few wrong ones. Some purist I'm sure will disagree to no end with what I will tell you but most of us out here in the real world don't really care do we ? Some of them only bring their noses down out of the air long enough to look down them anyway. If you are like me you are only doing this old tractor stuff because you enjoy it. You ... [Read Article]

Latest Ad: Oliver 550 Diesel runs like a watch three point hitch pto engine gone threw about two hundred hours ago nice clean tractor [More Ads]

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy