Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 
Marketplace
Classified Ads
Photo Ads
Tractor Parts
Salvage

Community
Discussion Forums
Project Journals
Your Stories
Events Calendar
Hauling Schedule

Galleries
Tractor Photos
Implement Photos
Vintage Photos
Help Identify
Parts & Pieces
Stuck & Troubled
Vintage Ads
Community Album
Photo Ad Archives

Research & Info
Articles
Tractor Registry
Tip of the Day
Safety Cartoons
Tractor Values
Serial Numbers
Tune-Up Guide
Paint Codes
List Prices
Production Nbrs
Tune-Up Specs
Torque Values
3-Point Specs
Glossary

Miscellaneous
Tractor Games
Just For Kids
Virtual Show
Museum Guide
Memorial Page
Feedback Form

Yesterday's Tractors Facebook Page

  
Ford Tractors Discussion Board

Ford 640 - How should the coil be wired


[ Expand ] [ View Replies ] [ Add a Reply ] [ Return to Forum ]

Posted by tgemignani on March 28, 2013 at 08:24:23 from (204.77.163.4):

I was recently gifted a Ford 640 tractor. Pulled it off the trailer and the battery was dead. I purchased a new 6v battery and connected it to the tractor, positive going to the right side (passenger) and negative to the left (driver). The tractor cranked right up and was driveable but obviously wasn't reaching it's full potential as backfiring occurred at higher RPM's. I pulled the tractor into the barn and backed off the throttle to Idle whereupon it died. The weather turned colder and I wanted to go plow the driveway but could not get the 640 started no matter what I tried, plenty of fuel was flowing through both the filter and the carb (checked the drain plug on the carb).

I assumed it was a coil or spark issue so I purchased a new coil from Tractor supply. I wired the coil with the positive going towards the rear of the tractor (ground?) and the negative going to the distributor. This seems correct to me in a positive ground situation as the negative is the hot lead. When hooking up the coil the darn ground (rear) wire broke apart due to age so I stripped the end of the lead off for testing, I was able to get short bursts of spark but tapping the positive lead on the coil with the stripped wire and the tractor fired! My issue is that now I get no spark when touching the coil and the tractor refuses to start again. I have no idea if the coil is wired properly because every post I read says something different in regards to positive or negative ground situations.

Any help on this would be greatly appreciated.

Thanks


Replies:




Add a Reply

:
:
:

:

:

:

:

:

:

: If you check this box, email will be sent to you whenever someone replies to this message. Your email address must be entered above to receive notification. This notification will be cancelled automatically after 2 weeks.


 
Advanced Posting Tools
  Upload Photo  Select Gallery Photo  Attach Serial # List 
Return to Post 

TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Today's Featured Article - Sunday Drives - by Cowboy. Summer was finally upon us here in Northern Maine. We have two types of industry up here, one being "Forestry" (Wood Products) and the other "Farming" (Potatoes). There is no shortage of farm tractors and equipment around here! I have been restoring old Farm Tractors for the past 6 years, and have found it easier and less expensive to hit all the auctions and purchase whole tractors for parts needed. My wife who works at a local school, and only has weekends and summers off, while on t ... [Read Article]

Latest Ad: Oliver 550 Diesel runs like a watch three point hitch pto engine gone threw about two hundred hours ago nice clean tractor [More Ads]

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy