TRACTOR PARTS Allis Chalmers Case & David Brown Farmall & International Ferguson Ford & New Holland John Deere Massey Ferguson Massey Harris Minneapolis Moline Oliver & Cockshutt Kubota / Yanmar

TRACTOR MANUALS

Allis Chalmers	Case	Farmall IH	Ford 8N,9N,2N	Ford
Ferguson	John Deere	Massey Ferguson	Minn. Moline	Oliver

Tractor Talk Discussion Forum

OT Bandsaw Mill

Welcome Guest, Log in or Register

Author

farrviewsouth

01-29-2007 17:22:10

Report to Moderator

Seventh attempt to post pictures of bandsaw sawmill :>

http://www.flickr.com/photos/farrviewsouthfarm/

[Log in to Reply] [No Email]

Keith-OR

01-29-2007 22:04:45

Report to Moderator

Re: OT Bandsaw Mill in reply to farrviewsouth, 01-29-2007 17:22:10

Good looking bandsaw mill. Post some more pictures of it...

Keith

[Log in to Reply] [No Email]

Janicholson

01-29-2007 17:38:07

Report to Moderator

Re: OT Bandsaw Mill in reply to farrviewsouth, 01-29-2007 17:22:10

Put your photo in bits and pieces to the left (follow the instructions), Then right click on the image and copy the location U R L to the image link location below. YOu will need a message in the box as well. I tried to link to your upload site. It opened on their site, but would not transfer to this site. JimN

[Log in to Reply] [No Email]

farrviewsouth

01-29-2007 18:29:15

Report to Moderator

Re: OT Bandsaw Mill in reply to Janicholson, 01-29-2007 17:38:07

Thank you for the reply. I must just be "thick" when it comes to this. I will try again

[Log in to Reply] [No Email]

farrviewsouth

01-29-2007 18:31:10

Report to Moderator

Son of a Gun, I think I've got it..... in reply to farrviewsouth, 01-29-2007 18:29:15

This should be a picture of the finished mill

[Log in to Reply] [No Email]

farrviewsouth

01-29-2007 17:27:09

Report to Moderator

Re: OT Bandsaw Mill in reply to farrviewsouth, 01-29-2007 17:22:10

I just cannot seem to get a handle on this picture posting within a message :>

I thought the mill would be on interest to the group. The basic design came from a set of plans by Bill Reeks, 7104 US HWY 231S. Cromwell, KY (270) 274-3361, which I highly recommend. Changes were made based upon my operating a Woodmizer for several years, my brother's ideas and looking at a variety of homemade mills.

[Log in to Reply] [No Email]

dan hill

01-30-2007 03:44:31

Report to Moderator

Re: OT Bandsaw Mill in reply to farrviewsouth, 01-29-2007 17:27:09

You need a guard on the blade.Those blades do break.

[Log in to Reply] [No Email]

farrviewsouth

01-30-2007 03:55:49

Report to Moderator

Re: OT Bandsaw Mill in reply to dan hill, 01-30-2007 03:44:31

Yes,I agree. "Finished" is a relative term. I need to finish building both a guard for the blade and one for the sprockets and continue working on a portable carriage.

[Log in to Reply] [No Email]

[Options] [Printer Friendly] [Posting Help] [Return to Forum] [Log in to Reply]

TRACTOR PARTS	TRACTOR MANUALS

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home | Forums

Copyright © 1997-2023 Yesterday's Tractor Co.
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy