(800) 853-2651 View Cart
 

• Tractor Parts
• Engine Kits
• Carburetors
• Manuals
• DVDs
• Hats
• Books


• Contact Us
• Shipping Rates
• Return Policy
• Ordering Help
• Company Info
• Parts Warranty
• Forums


John Deere 720 Tractor Parts

[ Show Pictures ]

[Categories]   [All John Deere Models]   [Print]  


Brakes
Brake Lining - Set of 4 Shoe Linings with 40 rivets. For tractor models 720, 730, 80, 820, 830 all except hi-crop. (Part No: AF2866R)
$37.18

Brake Linings With Rivets - For 60, 620 HI-CROP, 620 ORCHARD, 630 HI-CROP, 630 ORCHARD, 70 HI-CROP, 720 HI-CROP, 730 HI-CROP, A AFTER SN# 410000, AO AND AR AFTER SN# 250000, G, GH, GN, GW. Brake Linings with rivets. Includes (4) linings and 32 rivets. (Part No: AA4253R)
$23.99

Brake Oil Seal - This brake oil seal has a 1.5 inch Inside Diameter, a 1.987 inch Outside Diameter and is .313 inch wide. It Fits: 520, 530, 620, 630, 720, 730. Replaces: AF2788R, AR20149R, CR14832 (Part No: AR20149R)
$11.09

Brake Shoe Spring - Fits John Deere - 820 2 cylinder, 830 2 cylinder (GAS), 830 2 cylinder (DSL), A, G, R, 60, 70, 80, 520, 530, 620, 630, 720, 730; Replaces: R21753, R21753R, A348R (Part No: R21753)
$3.68

Pulley Brake Pad , Set of 2 pads - For tractor models A, B, 50, 520, 530, 60, 630, 70, 720, 730. *** Enter qty 1 for a set of 2 pads, priced per set. (Part No: RE29790)
$20.73

Clutch
Clutch Bushing - For tractor models 620, 630, 70, 720, 730. (Part No: F1390R)
$39.38

Clutch Drive Disc - 20 tooth, 6 spline, 9.940 inch diameter. For tractor models 70, 720, 730. (Part No: F1228R)
$135.42

Clutch Drive Disc, Sliding - Sliding Drive Disc is 20 spline, 10 inch O.D. For tractor models 60, 620, 630, 70, 720, 730 tractors. (Part No: A4355R)
$68.62

Clutch Facing - Pulley clutch facing. Floating. For tractor models A, G, 60, 70, 620, 630, 720, 730. 10 inch outside diameter, 6-3/4 inch inside diameter, 1.575 inch wide, .15 inch thick. For 60, 620, 630, 70, 720, 730, A, G. Replaces: C614R, R90215. PRICED EACH. If you order 1, you will receive only 1 clutch facing. (Part No: TP-C614R)
$11.99

Clutch Facing, Pulley - Replaces AA5082R. Fits 60, 620, 630, 70, 720, 730. (Part No: AA6129R)
$44.63

Clutch Operating Bolt - 3 used per tractor, sold individually. For tractor models 70, 720, 730. (Part No: F1392R)
$39.38

Clutch Pin - Clutch linkage pin. Made in the USA, 9/16" diameter, 1/16" oversized to compensate for wear, use 9/16" drill to ream orginal hole, two used per tractor. For tractor models A, D, R, G, 60, 70, 520, 530, 620, 630, 720, 730. (Part No: D1994R)
$8.95

Dog, Clutch - For tractor models 620, 630, 70, 720, 730, A, AO, AR, D, G, GH, GN, GP, GW. Trhee required per tractor. (Part No: C74R)
$19.50

Cooling System
Fan / Generator Belt - This is a 0.453 inch X 45.57 inch wedge belt. Used on John Deere 60 series (s/n 30000 & up), 70 series (s/n 8100 & up), 70 dsl, 620, 630, 720, 730. Replaces A4897, A4897R, TX10276, 102752A, 303045080 (Part No: A4897R)
$5.99

Fan Drive Disc - For tractor models A, (B SN# 171992 and up), (G SN# 13910 and up), (H SN# 50500 and up), 50, 520, 530, 60, 630, 70, 720, 730. Also replaces B2123R. Measures 3.627 inches O.D., .747 inch Spline diameter, 10 splines, .989 inches thick. 2 Used per tractor, price is each. (Part No: AB3314R)
$33.75

Radiator Cap - For tractor models 50 SN# 5016616 and later, 60 Regular SN# 6030927 and later, 60 Standard SN# 6043000 and later, 70, 70 Diesel, 80, 420, 430, 435, 440, 520, 530, 620, 630, 720, 720D, 730, 730D, 820, 830, 840, 1010, 8020. Replaces AA5757R. Cap is 3 1/4 outside diameter, fitted for a 2 notch 2 1/4 inch radiator neck. (Part No: 400065)
$18.75

Radiator Core - This radiator core is for tractor models G (with water pump after SN# 60700), 70, 720, 730 ALL with gas engines. Radiator Core 21 1/2" H, 19 inch core width and 2 1/8 inch depth. Gasket set available as part R2180G. (Part No: AF1321R)
$292.35

Radiator Core - Diesel - This radiator core is made of copper fins and a brass lockseam tube. The radiator core is 21.5 inches tall, 19 inches wide, 2 inches thick, and has a plate width of 5.562". This radiator core fits John Deere Tractor models 70, 720, 730, 80, 820, 830 all with Diesel engines. Does not come with gaskets. Radiator Gasket available as part number F661R. (Part No: AR1627R)
$246.15

Radiator Filler Neck - This radiator filler neck fits 50 (sn 5016616 and up), 520, 60 (Standard sn 6043000 and up), 60 (sn 6030927 and up), 620, [ 70, 720 (Diesel) ], 70 (sn 7008450 and up), 720, 80, 820 2 cylinder, 830 2 cylinder; Replaces: AA5756R (Part No: AA5756R)
$88.80

Radiator Gasket Pair - Price is for 2 radiator core gaskets for models G, 70, 720, 730, 80, 820, 830. (Part No: F661R)
$10.50

Radiator Gasket Pair - Radiator Core Gaskets for models G, 70, 720, 730 using radiator core AF1321R. (Part No: R2180G)
$10.50

Radiator Strap - For tractor models: 60, 620, 630, 70, 720, 730, A, AO, AR, (G from s/n 13000 and up). (Part No: A192R)
$12.90

Radiator Water Pipe, Lower - For tractor models: (720 diesel with electric start from serial number 7222000), (730 diesel with electric start). (Part No: R20245R)
$46.10

Water Pipe, Lower - For tractor models 720, 730 both gas or LP. (Part No: F2759R)
$40.29

Water Pump - For tractor models 70, 720, 730. NOT FOR A MODEL 70D OR OTHER MODELS NOT LISTED. Includes gasket and single pulley. Fits 70 Serial number below 7031299 Gas and Diesel, 720 Gas and Diesel, 730 Gas and Diesel. Replaces AF2368R-R, R1052, ``F1052R (Part No: AF2368R)
$113.06

Decals and Emblems
Be Careful Plate - This plate is used on A, AN, (AW serial number 584000 and up), B, BN, (BW serial number 201000 and up), G, GM, (GN serial number 26000 and up), GW, R, 50, 520, 60, 620, 70, 720, 80, 820 2 cylinder. (Part No: R4473)
$10.49

Decal Set - Decal Set for John Deere Model # 720 Diesel, 15pc. (Part No: JD720D)
$44.18

Decal Set - For 720 Gas. COMPLETE decal set. Italic numbers with open top zero on the 720. (Part No: JD720)
$31.49

Front Medallion - Front Medallion for models 320, 420, 520, 620, 720, (820 2 cylinder). Medallion measures 4 1/2 inches wide, 3 1/4 inches tall. Does NOT come with retainers (Part No: AF3166R)
$101.12

Drive Train
2ND, 5TH, & Reverse Sliding Gear - 18 Teeth For 720, 730 (Part No: R0720)
$110.56

Countershaft 2ND & - 5th GEAR - 30 Teeth. For tractor models 720, 730. (Part No: R0719)
$169.25

Flywheel Cover Inspection Plate - For tractor models A, B, 50, 60, 70, 520, 530, 620, 630, 720, 730. (Part No: AB3579R)
$27.90

Gear Shift Knob - Plastic knob, 3/8 inch fine thread. For tractor models (A styled from serial number 648000), AR, AO, (B styled from serial number 201000), (G styled from serial number 13000), 50, 60, 70, 80, 520, 530, 620, 630, 720, 730, (820, 830 2-cylinder). (Part No: 03501AB)
$7.28

Electrical System
Battery Cable - For tractor models A to SN# 584000/up, B SN# 201000/up SN# 26001/up, 50, 60, 70D, 520, 620, 720D & 730D with cranking eng. 0 gauge, length 64", terminal type 1-3. (Part No: TP-AB3546)
$40.59

Battery Cable - Battery Cables: 70, 720G, 1 guage, length 73, terminal type 1-3*. For tractor models 70, 720. (Part No: TP-AF1754R)
$41.86

Battery Cable - Battery Cables: 720D, 730D with electric. start~ 3010D Row crop right hand~ 3010 Std. right hand to SN# T19800, 3020D row Syn. Range right hand to SN# 1T67999, 4010D Row & Hi Corp right hand~ to SN# 1T67999, 4010D Row & Hi Corp right hand to SN# 4010D Standard For 3010, 3020, 4010, 4020, 720, 730 (Part No: TP-AR20216)
$43.09

Battery Strap - Battery Ground Straps. A to SN# 676000/up, B SN# 286910/up, G SN# 51143/up, R, 50, 60, 70, 80, 520, 530, 620, 720, 730, 820, 830, 5010. 1 guage, length 6-1/2, terminal type Std+. For 50, 5010, 520, 530, 60, 620, 630, 70, 720, 730, 80, 820, 830, A, B, G, R (Part No: TP-AB4100R)
$10.29

Coil, 6V - Distributor Coil, 6 volt. Delco Remy equipped. For tractor models B, M, 40, 50(after 5021479), 60LP, 70LP, 320, 330, 420, 430, 440, 520, 530, 620, 630, 720, 730, 1010, 1020, 2010, 2020, 3010, 3020, 4010, 4020 - DR1115380, 1115381. For 1010, 1020, 2010, 2020, 3010, 3020, 320, 330, 40, 4010, 4020, 420, 430, 440, 50, 520, 530, 60LP, 620, 630, 70, 720, 730, B, M. Replaces AM373T. (Part No: D4PE12029AA)
$18.15

Combination Switch - Fits John Deere - 70, 720 (Diesel Pony start), 80, 820 2 cylinder (with Pony Start) Replaces: AF2065R, AF2460R (Part No: AF2065R)
$72.17

Combo Switch Lever - Used with switches AM1866T, 10A971, 1K7654A, AR20430, AA5397R, 168089A, 30-3365891. For tractor models 1020, M, 50, 520, 530, 60, 620, 630, 70, 720, 730, 320, 330, 420, 430, 435, 440, 1520, 2020, 8430, 8630, 40. (Part No: A4653R)
$3.63

Distributor - Wico B-4 - For tractor models 70, 720, 730, 80, 820, 830 FOR PONY STARTING MOTOR ENGINE. Wico Model B-4 Distributor, complete, new. (Part No: AR1370R)
$343.48

Distributor Cap - This Distributor cap for a 2 Cylinder with a Delco Distributor, Vertical, 12 Volt. Plug connectors on cap are at 90 degrees or 12:00 o-clock and 3:00 o-clock. For Delco distributors up to 1963 on models: A, AR, AO, B, G, M, 40, 50, 60, 70, 320, 330, 420, 430, 440, 520, 530, 620, 630, 720, 730, 1010, 2010, 3010, 4010, 114W, 116W, 323W. Balers~ 25, 30, 40, For 1010, 105, 114W, 116W, 12, 2010, 215, 215A, 25, 299, 30, 3010, 320, 323W, 330, 40, 4010, 420, 430, 440, 45, 50, 520, 530, 55, 60, 600, 620, 630, 65, 70, 700, 720, 730, 95, 99, A, AO, AR, B, G, M. (Part No: 1935038)
$9.02

Distributor Cap, Vertical, 6 Volt - Distributor cap for Delco distributor, 2 cylinder, vertical, Please note the orientation of the 2 non-plugged terminals on top of the distributor cap (click "enlarge image"), there are two different orientations available (see Part No: 1935038 for the other orientation). Fits A, B, G, M, 320, 330, 40, 420, 440, 50, 520, 530, 60, 620, 630, 70, 720, 730. (Part No: 1909008)
$8.39

Distributor Dust Cover - Fits early Delco Distributor with Clip Held Cap. For tractor models A, AR, AH, AN, ANH, AO, B, BR, BN, BNH, BW, BWH, G, GN, GW, M, MC, MI, MT, 40, 50, 60, 70, 320, 330, 420, 430, 440, 520, 530, 620, 630, 720, 730, 1010, 2010, 3010, 4010. (Part No: 1900119)
$6.75

Distributor Shaft Bushing and Shim Kit - Delco Distributor Shaft Bushing and Shim Kit. Fits M, MC, MI, MT, 320, 330, 40, 420, 430, 440, 520, 530, 620, 630, 720, 730, 1010, 2010, 3010 with one of the following Delco distributors: 1112623, 1112623, 1112577, 1112648, 1112581, 1111418. Replaces: washer: 811912, shim washer: 810074, 810078, bushing: 1909003, 1952334 (Part No: ABC3007)
$22.50

Distributor, Rebuilt - This Rebuilt Distributor comes complete with Cap, Points, Condenser and Shaft Gear. For tractor models 520, 530, 620, 630, 720, 730. Replaces 1112576. Add $80.00 core charge to price - this charge is refundable if you send your core to us. (Part No: 1112576)
$157.71

Electronic Ignition Conversion Kit, 12 Volt Negative Ground - For tractor models 50, 60 and 70 Gas with Delco 1112569; 520 and 530 Gas with Delco 1112569; 60, 70, 620, 630, 720, 730 Gas with Delco 1112576. Electronic Ignition Conversion Kit, replaces points and condenser with an electronic module. Use on 12 volt negative ground system. (Part No: 1122)
$100.92

Electronic Ignition Conversion Kit, 12 Volt Positive Ground - Use on the following tractors: 50, 60, 70, 520, 530, 620, 630, 720, and 730 with 2-cylinder gas engine using Delco distributor # 1112569 or 1112576. Electronic ignition conversion kit by Pertronix. Replaces points & condenser with an electronic module. Used Only on tractors with 12 volt POSITIVE ground systems. (Part No: 1122P12)
$110.28

Electronic Ignition Conversion Kit, 6 Volt Positive Ground - Use on the following tractors: 50, 60, 70, 520, 530, 620, 630, 720, and 730 with 2-cylinder gas engine using Delco distributor # 1112569 or 1112576. Electronic ignition conversion kit by Pertronix. Replaces points & condenser with an electronic module. Used Only on tractors with 6 volt POSITIVE ground systems. (Part No: 1122P6)
$110.28

Ignition Kit, Delco Clip-Held Distributor Cap - Contains points, condenser, and rotor. VERIFY DISTRIBUTOR NUMBER TO ENSURE FIT. For: A, AN, AH, AR, AO, B, BN, BW, D, G, M, 40, 50, 60, 70, 320, 330, 420, 430, 440, 520, 530, 620, 630, 720, 730, 1010(to 42000), 2010(to 42000), 3010 (to 1E32999), 4010(to For 1010), 105, 114W, 116W, 2010, 215, 215A, 25, 299, 30, 3010, 320, 323W, 330, 40, 4010, 420, 430, 440, 45, 50, 520, 530, 55, 60, 600, 620, 630, 65, 70, 700, 720, 730, 95, 99. For Delco distributor numbers 1112623, 1112577, 1112648, 1112581. (Part No: ATK1DCR)
$7.34

Ignition/Light Switch, 6 Terminal - Uses A4653R lever. For tractor models (50 from SN# 5021480), (60 Row Crop from SN# 26000 and Std from SN# 43000), (70 LP), 520, 620, (720 gas). (Part No: AA5397R)
$49.45

Push Button Starter Switch - 3 Terminal Push Button Starter Switch with Rubber Cap. Fits 80, 720, 730, 820 2 cylinder, 830 2 cylinder (with Pony start)530, 630, 730 (Gas, LP, All fuel. This starter switch has 5/8 - 32" thread O.D., 3 screw terminals. Replaces: AR21219, AR21823, AR20431, AR1324R (Part No: AR21219)
$16.25

Rear Wiring Cover - For 520, 530, 620, 630, 720, 730 (cut to length). Rear Wiring Cover from the wiring harness to axle housing. (Part No: AR20932R)
$9.75

Rebuilt Delco Generator - This rebuilt generator fits the following tractor models:70 (diesel), 720 (diesel with serial number 7200000 and above), 730 (diesel with serial number 7200000 and above), 80 (pony motor), 820 (pony motor), and 830 (pony motor). Please note that there will be an additional core charge of $35 – this is refundable if you send your core to us. Replaces: TG-70, 1947580, SE501430, 1100027, 1100038, 1100048, and 1100054. (Part No: AR21907)
$246.18

Spark Plug Cover, LH - For tractor models 520, 530, 620, 630, 720, 730. Left Hand Side. Includes rubber grommet. ***NOTE: Picture shows both but this is only the left hand side. (Part No: F2630R)
$39.32

Spark Plug Cover, RH - For tractor models 520, 530, 620, 630, 720, 730. Right Hand Side. Includes rubber grommet.***NOTE: Picture shows both but this is only the right hand side. (Part No: F2631R)
$39.32

Starter Brushes - Carbon Starter Brush, 4 Brushes included. For model s. A, 60, 720D, 730D {B} For 60, 720, 730, A (Part No: 1906909)
$9.90

Switch Starter - This Two Terminal Switch, with side screw terminal for tractors: 50, 60, 70, 520, 620, 720. Fits starters: 1107188, 1107634, 1113004, 1113005, 1113041, 1113304 Replaces: 1930496, 1930505, D906, 1928209, 1934779, AR11006R, AR11115R (Part No: 1932850)
$10.15

Tune Kit - This Tune Kit is for John Deere tractors with 2 cylinder gas engines. Contains: Spark plugs, heavy duty points, condenser, rotor, and gap gauge. Using 7/8-18 thread, 5/8 reach, 15/16 hex spark plug. For Delco distributor thru 1963. For tractor models 320, 330, 40, 50, 520, 530, 60, 620, 630, 70, 720, 730. (Part No: JTTK3)
$20.40

Tune Kit - This Tune Kit is for John Deere tractors with 2 cylinder gas engines. Contains: spark plugs, heavy duty points, condenser, and rotor. Using 18m, 1/2 reach, 7/8 hex spark plug. For Delco distributors thru 1963. Fits tractors: 50, 520, 530, 60, 620, 630, 70, 720, 730. (Part No: JTTK4)
$13.83

Tune Kit - For John Deere tractors with 2 cylinder gas engines Using 7/8"-18 thread reach, 15/16 hex spark plugs. For Delco distributor thru 1963. Fits tractors 40, 50, 6 0, 70, 320, 330, 520, 530, 620, 630, 720, 730. Includes: Spark plugs, heavy duty points, condenser, rotor, and gap gauge, universal spark plug wires, and vertical distributor cap. FOR 12 VOLT SYSTEMS. (Part No: JTTK13-12V_)
$40.65

Tune Kit - Tune Kit - For John Deere tractors with 2 cylinder gas engines Using 18mm, 1/2 reach, 7/8 hex spark plugs. For Delco distributor thru 1963. Fits tractors 50, 60, 70, 520, 530, 620, 630, 720, 730. Includes: Spark plugs, heavy duty points, condenser, rotor, and gap gauge, universal spark plug wires, and distributor Vertical cap. FOR 12 VOLT SYSTEMS. (Part No: JTTK14-12V)
$34.08

Tune Kit - For John Deere tractors with 2 cylinder gas engines Using 7/8"-18 thread reach, 15/16 hex spark plugs. For Delco distributor thru 1963. Fits tractors 40, 50, 60, 70, 320, 330, 520, 530, 620, 630, 720, 730. Includes: Spark plugs, heavy duty points, condenser, rotor, and gap gauge, universal spark plug wires, and distributor cap. FOR 6V VOLT SYSTEMS. (Part No: JTTK13-6V_)
$40.02

Tune Kit - Tune Kit - For John Deere tractors with 2 cylinder gas engines Using 18mm, 1/2 reach, 7/8 hex spark plugs. For Delco distributor thru 1963. Fits tractors 50, 60, 70, 520, 530, 620, 630, 720, 730. Includes: Spark plugs, heavy duty points, condenser, rotor, and gap gauge, universal spark plug wires, and distributor cap. FOR 6V SYSTEMS. (Part No: JTTK14-6V)
$33.45

Tune Up Kit - For Pony Engine With Foreign Coils Contains Points, Condensor, universal Plug Wires and Coil. Consists of: 2 Point Sets, 2 Condensers, 2 Plug Wire Sets, & 2 Foreign Ignition Coils (Part No: R2531)
$181.44

Voltage Regulator - Voltage Regulator, (6 Volt). Fits 720, 730, 820, 830 tractors (Part No: 1118786)
$40.47

Voltage Regulator, 24 Volt - This Voltage Regulator is used on 24-Volt systems using Delco generator # 1103021 and 1103026. 3010, 4010, (3020 Diesel up to Serial Nuimber 122999), (4020 Diesel up to Serial Number 200999), (500 Diesel up to Serial Number 67999), 5010, (600 Diesel up to Serial Number 90999), (720 Electric start diesel Serial Number 7222600 and up), (730 Electric start diesel), (830 2 cylinder Electric start), (840 Electric start up to Serial Number 8400199) Replaces: 1118292, 1118347, 1118957, 1119282, AR11008, AR30155 Flat Mount. For 24-Volt generator system, 4 terminals, A circuit, 8 - 12 AMPS, works on negative or positive polarity (Part No: TP-AR30155)
$81.97

Voltage Regulator, External, 12 Volt - This 12 Volt Saddle Mount Voltage Regulator has 3 Terminals. For 12V A, G, 50, 60, 70, 520, 530, 620, 630, 720, 730, all using generator 1100309. Replaces regulator 1118792. Saddle Mount (Part No: VR1820)
$21.88

Engine Gaskets
Full Gasket Set - For tractor models: 720, 730 gas. (Part No: FS2703)
$281.73

Head Gasket Set - For tractor models: 720, 730 gas. (Part No: HS2703)
$202.00

Engine Rebuild Kits
Rebore Kit - DIESEL - STD - Piston Kit For 70, 720 and 730 DIESEl. 6 1/8" bore STANDARD. Contains pistons, rings, pins, and retainers. (Part No: R2034)
$730.01

Valve Train Kit - Kit contains valves, guides, springs and locks. For tractor models 720, 730 both with diesel engines. (Part No: VTKJD720D)
$340.20

Engine Parts
Flywheel Ring Gear - For tractor models 70, 720, 730 all with gas engines. 210 Teeth. Replaces original part number F1227R (Part No: F1227R)
$119.23

Flywheel Ring Gear - 168 teeth, inside diameter just under 20 inches. For tractor models (A SN# 477000 to 583999), (AO, AR up to SN# 271999), (G, 70, 720, 730 diesel). (Part No: A2238R)
$119.23

Flywheel Ring Gear - Used on Pony starting engine. For tractor models R, 80, 720, 730, 820, 830. (Part No: F2265R)
$79.10

Heat Exchanger - For tractor models 60, 620, 630, 70, 720, 730. Replaces BMD# BH-A4644R. (Part No: A4644R)
$32.31

Valve Lock - Pair - This pair of valve locks is a set for 1 valve. For tractor models 60, 620, 630, 720, 730, 80, (820, 830 2 cylinders), (A from SN# 488000), (AO, AR from SN# 260000 and up), R, (70 gas, LP and diesel). (Part No: A2332R)
$21.98

Valve Spring - For tractor models 70, 720, 730 all with diesel (Part No: F2143R)
$26.98

Valve Spring - Exhaust only. For tractor models (70 gas, LP & all-fuel), (720, 730 gas, LP). (Part No: F1114R)
$25.20

Valve, Exhaust - For tractor models (70, 720, 730 all diesel), R. Replaces AF3192R, AR584R. (Part No: F3214R)
$46.07

Valve, Intake - For tractor models 720, 730 both with diesel engines. Replaces AF3191R. (Part No: F3213R)
$40.95

Exhaust System
Exhaust Chrome Curved Stack - Chrome For Unstyled A, G, 60, 70, 620, 630, 720, 730. 4 inch outside diameter, 24 inch in length. (Part No: R3551)
$135.44

Exhaust Chrome Straight Pipe - Chrome Pipe with 4 bolt flange is 4" O.D. Length 24". For Unstyled A, G, 60, 70, 620, 630, 720, 730 (Part No: R3550)
$114.61

Exhaust Pipe - A= 2 bolt inlet, B= 13" vertical length, C= 25" horizontal length, D= 2-1/2" outlet O.D.. Use with manifold F30305R and mufflers R21826R, AR20450 and AA2214R. For tractor models (70 from 1953-1955), (720 from 1956-1958), (730 from 1958-1959). (Part No: AR20516R)
$35.28

Heat Exchanger - For tractor models 60, 70, 620, 630, 720, 730. (Part No: A4664R)
$31.45

Heat Exchanger, Clamp - Clamp with stud and nut, use with B3213R & A4664R heat exchangers. (Part No: A4645R)
$8.93

Manifold - Without Heat exchanger.For tractor models 720 and 730. 2 piece Intake and Exhaust Manifold. Gasket set Available Separately as part number R0215G. Uses heat exchanger A4645R and Clamp A4664R. Replaces: F3034R, F3035R (Part No: F3034R)
$282.83

Manifold Gasket Set - This Gasket Set is used with F3034R Manifold. It replaces A4631R, A4642R, AF1688R, AF2608R, AF3724R, R524090 (Part No: R0215G)
$25.73

Muffler - Unstyled (no dent) For tractor models A, G, 620, 70, 720. Replaces AF3770R. Outlet is 2 1/2 inches, 24 1/4 overall length. (Part No: AA300R)
$48.76

1938-1953), 60, 70, 620, 720 (gas & all fuel). Replaces AF3770R and R21826." />
Muffler, Vertical - Vertical muffler with dent, round body 4-Bolt Base plate, 2-1/2" exhaust O.D., ~ 24-1/2" total length~ 3-3/4 body diameter. For tractor models: (A, AR, AN, AW, AWH all 1933-1952), G (SN# 410000> 1938-1953), 60, 70, 620, 720 (gas & all fuel). Replaces AF3770R and R21826. (Part No: AA2214R)
$35.97

Muffler, Vertical - Round body 4-1/4" shell diameter, 4 bolt mounting plate, A= 4-1/2" inlet length, B= backing plate, C= 14-1/2" shell length, D= 2-1/2" outlet length, E= 2-5/8" outlet O.D., F= 21" overall length. For tractor models (A, AN, ANH, AR, AW all SN# 410000 and up), 60, 620, 70, 720. This style is not available from the OEM. (Part No: R21826R)
$30.50

Straight Pipe - Stainless Steel, Straight Stack. Double wall construction with 4 bolt flange. 24 inches tall, 4 inch outside diameter. For tractor models Unstyled A, G, 60, 70, 620, 630, 720, 730. (Part No: R3549)
$111.57

Vertical Muffler - With inlet I.D. plate. Outlet O.D. is 2-5/8", Length is 21". OVAL SHAPED. For tractor models 60, 620, 630, 70, 730 Gas; and for diesel Models 70, 720, 730. (1084R) (Part No: AR20450R)
$48.89

Fuel System / Air Intake
Air Cleaner Stack - This air cleaner stack fits tractor models: G, 620, 630, 720, and 730. It measures 23-3/4 inches tall, has a 4 hole mounting flange and Replaces: AF656R, AR20668R. (Part No: AF656R)
$88.32

Air Precleaner Assembly - For 520, 530, 620, 630, 720, 730. Air Precleaner Assembly. (3817R) (Part No: AF3580R)
$98.68

Air Stack Adapter - For tractor models 720, 730. (Part No: F3090R)
$65.92

Air Stack Muffler Spacer Block - For 620, 630, 720, 730. (Part No: R21057R)
$48.30

Carburetor Bowl - Fits double barrel DLTX model Marvel Schebler carburetors. For tractor models 50, 60, 70, 520, 530, 620, 630, 720, 730. (Part No: A5173R)
$39.38

Carburetor Float - For tractor models 50, 60, 70, 520, 530, 620, 720, 530, 630, 730. Carburetor Float. Replaces: AA4353R, AA5656R, AA6632R, AA6633R, AB4636R, AB4794R, AB5150R, AB5151R, AF1561R, AF1632R, AF2826R, AF2827R, AR10069R, 30-713. Used on the following carburetors: DLTS75, DLTX101, DLTX102, DLTX105, DLTX106, DLTX109U, DLTX81, DLTX82, DLTX83, DLTX84, DLTX85, DLTX86, DLTX94, DLTX95, DLTX96, DLTX97, DLTX98, DLTX99. Measures 66.3mm Long x 27mm Wide x 30mm Thick. (Part No: AR10069)
$30.00

Carburetor Kit, Basic - Kit for Marvel DLTX75, DLTX83, DLTX86, DLTX96, DLTX105, DLTX99, DLTX81, DLTX84, DLTX82, DLTX102, DLTX97, DLTX94, DLTX106, DLTX85, DLTX101, DLTX98, DLTX95 carbs used on 50, 520, 530, 60, 620, 630, 70, 720, 730. (Part No: MS105)
$28.21

Carburetor Kit, Economy, Pony Motor - Used with Pony starting engine with Zenith carbs #11681 & 12172. For tractor models 70 diesel, 80, (720, 730 diesel), (820, 830 both 2 cylinder). (Part No: R5284)
$53.48

Carburetor Repair Kit - Basic carburetor repair kit~ contains needle float valve, throttle shaft, float lever shaft and gasket set. Comes with VITON needle float valve. Carburetor manufacture numbers: DLTX81, DLTX82, DLTX84, DLTX85 and AA5344R, For 60, 620, 630, 70, 720, 730 (Part No: BK35V)
$24.00

Carburetor, Rebuilt - Fits 70, 720 - replacement for OEM DLTX81, DLTX82, DLTS84, DLTX85, DLTX95. Add $200.00 core charge to price - this charge is refundable if you send your core to us. (Part No: 1522-CARB)
$278.31

Choke Knob - For tractor models A, B, D, G, H, R, 50, 60, 70, 520, 530, 620, 630, 720, 730, 820, 830. (Part No: B1951R)
$11.25

Fuel Filter Canister - 2 required per tractor. For tractor models R, 70, 80, 720, 730, 820, 830. Diesels. (Part No: R473R)
$31.50

Grommet, Fuel Filler, Black - For tractor models 70, 620, 630, 720, 730, 1020, 1520, 2020, 3010, 3020, 4010, 4020, 5010. Measures 3 7/8 inch outside diameter, 2 1/4 inch inside diamter, and 3 1/2 inch diamter on underside lip. (Part No: A5157R)
$19.95

Precleaner Cover, Metal - 7" diameter with brass nut, fits Donaldson pre-cleaners. For tractor models Some 60, 70, 520, 530, 620, 630, 720, 730, (820, 830 3-cyl), (1010, 2020, 2520 diesel), 2010, 2030, 2040, 2150, 2155, 2240, 2255, 2355, 2440, 2510, 2630, 2640, 2840, 3010, 3020, 4000, 4010, (4020 gas or LP). (Part No: AF3583R)
$26.48

Sediment Bowl Assembly - Large Bowl. 1/8 inch pipe thread to fuel line, 3/8 pipe to tank. For tractor models A, B, 60, 620, 70, 720, 730, 80, 820, 830. Fuel Strainer assembly with 2.25 inch bowl. (Part No: S.61581)
$16.22

Sediment Bowl Assembly Glass Bowl - Fits S.61581 fuel strainer. For tractor models A, B, 60, 620, 70, 720, 730, 80, 820, 830. (Part No: S.65504)
$5.18

Sediment Bowl Gasket and Screen - This is a 2 Inch Outside Diameter Gasket and Screen. The Screen has a 3/8 Inch center hole. Replaces: L885T (Part No: 49923D)
$3.09

Speed Control Plate - With linings. For tractor models (520 from SN# 5208100 and up), (620 from SN# 6213100 and up), (720 from SN# 7214900 and up), 530, 630, 730. Replaces RE227867. (Part No: AF3847R)
$35.44

Speed Control Plate with Linings - For tractor models 50, 60, 70, (520 up to SN# 5208099), (620 up to SN# 6213099), (720 up to 7214899). Replaces R227852. (Part No: AA6077R)
$26.25

Speed Control Rod End Joint - Fits John Deere- [2510, 2520, 3010, 3020, 4000, 4010, 4020, 4030, 5010, 5020, 5200, 5400, 5440 (as a throttle speed control end joint; gas, lp, diesel)], 4230 (as a throttle speed control end joint; gas only), [50, 520, 530, 60, 620, 630, 70, 720, 730 (as a throttle speed control end joint; gas, lp, all fuel)], [5325N, 5425N, 5525N (as a PTO linkage end)], European: 5420 (as a throttle speed control end joint; gas, lp, diesel), Industrial 990 (as a throttle speed control end joint; gas, lp, diesel), 844 (as a throttle speed control end joint; gas, lp, diesel), [760, 760A, 762A, 860B, 862 (as a throttle speed control end joint; gas, lp, diesel)], [340D, 440C, 440D, 448D, 540B, 540D, 548D, 640, 640D, 648D, 740, 740A (as a throttle speed control end joint; gas, lp, diesel)], [500, 500A, 500B, 600, 700A (as a throttle speed control end joint; gas, lp, diesel)]; Replaces: AA5302R (Part No: AA5302R)
$12.25

Vent Tube and Radiator Overflow Packing - This packing installs in the nut that is on either end of your vent tube or one end of your radiator overflow tube. It is used on John Deere A, B, D, G, 50, 520, 530, 60, 620, 630, 70, 720, 730, 80, 820, 830. Replaces John Deere Part Number B60R (Part No: B60R)
$.56

Gaskets
Pony Motor Crankshaft Seal - This Pony Motor Crankshaft Seal Measures 1.000" I.D., 1.503" O.D., 0.250" Fits: 70 (Used as a Pony motor crankshaft seal (2 used per tractor) on Diesel models. Also used as a Pony Motor input shaft seal on Diesel models.), 720 (Used as a Pony motor crankshaft seal (2 used per tractor) on Diesel models. On the flywheel side up to SN: 721489 and on the crankshaft gear side all serial numbers. Also used as a Pony Motor input shaft seal on Diesel models.), 730 (Used as a Pony Motor input shaft seal on Diesel models.), 80 (used as a Pony motor crankshaft seal (2 used per tractor). Also used as a Pony Motor input shaft seal. ), [820 2 cylinder, 830 2 cylinder (Used as a Pony motor crankshaft seal (2 used per tractor). Also used as a Pony Motor input shaft seal. )] Sold individually. Replaces: AF2167R (Part No: 43800D)
$8.93

Gauges
Amp Gauge - For tractor models A, AO, AR, B, BO, BR, LA, LI, GN, GW, 50, 60, 70, 80, 320, 33, 520, 620, 630, 720, 730, 820, 830. This gauge has a plain face without a John Deere logo. This 20-0-20 ammeter has a metal base, glass lens, black faceplate and a black bezel. Replaces AM1864T, AF2749R. (Part No: R3803)
$22.04

Fuel Gauge, 12 Volt - This electric fuel gauge fits 2 Cylinder models; 520, 530, 620, 630, (720, 730 Gas), (720, 730 Diesel (12/24 volt electric start), (820 2 cylinder, 830 2 cylinder 12/24 volt electric start). This fuel gauge is calibrated to the original resistance, 0 - 30 OHMs, positive ground system. Replaces: AF2721R (Part No: AF2721R)
$42.75

Fuel Gauge, 6 Volt - This 6 volt positive ground fuel gauge is used on the following two cylinder diesel tractors with pony start motors: 70, 720, 730, 80, 820, 830. The gauge reads from 0 - 30 Ohms. Replaces original part numbers AF2170R, AF2739R (Part No: AF2739R)
$39.85

Fuel Sending Unit - This fuel sending unit is used on the following 2 cylinder tractors: 520, 530, [620, 630 (General Purpose, Standard or Orchard.)], [70, 720, 730 (Gas, LP, and Diesel)], 80, 820, 830, 840. It will work for 6 or 12 volt, positive or negative ground providing the appropriate gauge is used. This fuel sending unit is properly calibrated to the original resistance, 0 to 30 OHMs. It replaces original part numbers AB5139R, AF2173R, AR1112R (Part No: AR1112R)
$51.75

Oil Pressure Gauge - For tractor models: 50, 60, 70, 520, 530, 620, 630, 720, 730, all gas engines. Oil Pressure Gauge Black Face. Does NOT have "John Deere" on the face. Comes with studs. This oil pressure gauge has a metal base, glass lens and a black bezel. This is a dash mounted gauge and includes the studs and mounting bracket. This is a mechanical gauge. The measurement of the threaded fitting is 1/8” NPT. Replaces OEM #s AF2775R and AF2752R. (Part No: AF2752R)
$21.90

Tachometer - This new tachometer fits; A serial number 648000 and up, AO and AR serial number 272000 and up, B serial number 201000 and up, [ 50, 520, 530, 60, 620, 630, 70, 720, 730 (Gas/Lp) ], [ 70, 720, 730 (Diesel) ], [ 80, 820 2 cylinder, 830 2 cylinder, 840 2 cylinder (Serviceable, Face plate will have the wrong Mph.) ]; Replaces: AB5132R, AB5134R, AF1719R, AF2066R, AF2698R, AR20055R, AR20825, AR20836, AR21661, AR21662, AR21663, AR21663R, AR21664R (Part No: R4611)
$104.19

Tachometer Cable - For tractor models (70 diesel), (720 diesel). Replaces AR21160R, AF3258R, AF2248R, AF2067R. (Part No: AF2246R)
$45.77

Tachometer Cable - For model 720 gas & LP. (Part No: AF3259R)
$45.77

Water Temperature Gauge - Black face. 72 inch lead. Without John Deere Logo. 140-230. For tractor models A, AR, B, D, G, M, R, 40, 50, 60, 70, 80, 320, 330, 420, 430, 440, 520, 530, 620, 630, 720, 730, 820, 830, 840. Also replaces AA6295R, AA7263R, AM2444T, AT13849T, AR20783R. (Part No: AR490R)
$26.25

Water Temperature Gauge - For 50, 60, 70, 520, 530, 620, 630, 720, 730. Water Temperature Gauge without John Deere logo on black face. Comes with 36" lead. (Part No: R3813)
$29.01

Water Temperature Gauge - This temperature gauge is for models 50, 60, 70, 520, 530, 620, 630, 720, 730. This gauge has a plain face without a John Deere logo. This water temperature gauge has a metal base, glass lens and a black bezel. This gauge has a 6 foot capillary lead. Please measure the length required for your tractor before ordering. The measurements are: 5/8 inch 18 NF end with a 1/2 inch NPT pipe bushing. Replaces OEM #s: AR490R, AT13849T, AR20783R, AM2444T, AA7263R, AA6295R (Part No: R3814)
$29.01

Hitch / Drawbar
3 Point Adjustable Upright Assembly - For tractor models 520, 530, 620, 630, 720, 730 except Hi-Crop. Replaces AF2676R (handle), AF2706R, AF2707R, B2804R, DA5883A, F2670R, F2671R, F2673R, F2674R, F2675R, F2676R, F2679R, JD7759, 11H218, 12H303, 14H785, 16H1419 (rivet/pin), 19H1901, 34H78, 34H118, 34H152. (Part No: AF2704R)
$248.40

Center Link Assembly - For 520, 530, 620, 630, 720, 730. Center Link Assembly. Asssembly consists of one of each of the following items: AF2873R, AR21917R, AF2798R & AF2799R. (Part No: AF520TL)
$277.02

Center Link Body with Handle - For tractor models 520, 530, 620, 630, 720, 730. Center Link Body with Handle. (Part No: AF2873R)
$133.46

Center Link End, Hook - For tractor models 520, 530, 620, 630, 720, 730. Center Link End - Hook. (Part No: AR21917R)
$119.33

Drag Link Sleeve - For 60, 70, 620, 630, 720, 730 with Adjustable Round Front Axle. OEM# C838R, C840R, AF1187R (Part No: R3851)
$94.27

Drawbar Pivot Pin - For tractor models (620 from SN# 13100 and above), (G from SN# 18700 and above), 630, 70, 720, 730. Replaces F856R, AF1318R. (Part No: AF3759R)
$26.20

Leveling Screw - This Right Hand Leveling Screw measures 19.44 inches in length, 1.125 inches diameter and 7 UNC right hand threads. For 520, 530, 620, 630, 720, 730 All Models Except Hi-Crop (Part No: AF2706R)
$104.66

Leveling Screw - Left Hand For 520, 530, 620, 630, 720, 730 All Models Except Hi-Crop (Part No: R2018)
$57.13

Leveling Screw Yoke - For tractor models 520, 530, 620, 630, 720, 730 all NON high crop models. (Part No: AF2670R)
$108.68

Rockshaft Return Spring - For tractor models 520, 530, 620, 630, 720, 730. (Part No: F2897R)
$56.00

Sway Block, RH - For tractor models 520, 530, 620, 630, 720, 730. (Part No: R2095)
$43.31

Top Link, Cat I - For tractor models 520, 530, 620, 630, 720, 730. Replaces AF2873R, AR21917R, AF2799R. (Part No: AF2798R)
$257.99

Hydraulic System
Hydraulic Lever Grip - For tractor models 80, 520, 530, 620, 630, 720, 730, 820, 830, 840. (Part No: F2948R)
$10.40

Lights
12 Volt Bulb - This bulb allows you to use the AR77326 work light for 12 volt applications. (Part No: S.51140)
$3.98

Bulb, Sealed Beam, Flood - 12-Volt Hi-Beam with Double Contact. It is 35 Watt with a 4.4 Inch Outside Diameter. It is Interchangeable with original lamp 4406 and 4410. Check lamp number before ordering. Replaces: AR21059 (Part No: 28A116)
$11.60

Fender Headlight, 12 Volt - Used with flat top fenders. For tractor models 520, 530, 620, 630, 720, 730. (Part No: R4786)
$74.42

Fender Headlight, 6 Volt - Use on flat top fenders. For tractor models 520, 530, 620, 630, 720, 730. (Part No: R4785)
$75.84

Lens - Lens, combination front or rear light, 5 diameter, for light TP-AA3075R on tractors: A, B, D, G, R, 70D, 720D, 730D, 80, 820, 830.* Manufactured to restoration standards. For 70, 720, 730, 80, 820, 830, A, B, D, G, R (Part No: TP-A2731R)
$19.11

Light Bracket - For tractor models 50 after SN# 5002931, 60, 60 Standard after SN# 6043000, 60 LP after SN# 6026000, 70, 720. Light Bracket. (Part No: A4465R)
$44.78

Light Bulb, Sealed Beam, 12 Volt - This 12-Volt Sealed Beam has Double Contact. It is 35 Watt. Has a 4.365 inch outside diameter. Replaces: L4411, 4411, AF3892R, AT11898. (Part No: 373662R91)
$8.48

Rear Combo Light - For 50, 520, 530, 60, 620, 630, 70, 720, 730 - ALL GAS. 70, 720, 730, 820, 830 - ALL DIESEL WITH ELECTRIC START. 12V Rear Combo Light, 5". (3869R) (Part No: AA5199R)
$70.38

Rear Combo Light - For 70, 720, 730, 80, 820, 830 - ALL WITH DIESEL WITH PONY MOTOR. 6V Rear Combo Light, 5". (3870R) (Part No: AF3088R)
$73.67

Red Light with Brass Ring - For tractor models A, B, G, R, 40, 320, 420, 430, 50, 60, 70, 80, 520, 530, 620, 720, 730, 82, 930, 1020, 2020, 2030, 2355, 2440, 2510, 2520, 2555, 2630, 2640, 2755, 2840, 2855, 2940, 2955, 3010, 3020, 4010, 4020, 4320, 4520, 4620. (Part No: AA925R)
$6.50

Ring - Moulding trim ring for headlights or rear lights, for light TP-AA3075R.* Manufactured to restoration standards. For tractor models 70, 720, 730, 80, 820, 830, A, B, D, G, R. (Part No: TP-AA3241R)
$19.11

Work Tail Light - 2 wire connectors. 6 Volt. For tractor models 50, 60, 70, 80, 520, 530, 620, 720, 730, 820, 930, 1020, 2020, 2030, 2355, 2440, 2510, 2520, 2555, 2630, 2640, 2755, 2840, 2855, 2940, 2955, 3010, 3020, 4010, 4020, 4320, 4520, 4620. If you have a 12 volt application, order bulb # S.51140 for an additional cost. (Part No: AR77326)
$51.67

Miscellaneous
Umbrella Bracket Assembly - For tractor models with Battery Box Mounted Seats: 50, A, 60, B, G, 520, 530, 620, 630, 70, 720, 730, 80, 820 2 cylinder, 830 2 cylinder, R. (Part No: AA4206R)
$92.49

Oil System
Oil Filter - Oil filter element, cartridge type 6-7/16" Tall, 3-1/8" Wide. Does not come with seal or gasket. For tractors: A, B, D, G, R, 50, 60, 70, 520, 530, 620, 630, 720, 730, 3010, 3020, 4000, 4010, 4020, 4030 (Part No: AR26350)
$4.58

Oil Pressure Sending Unit - For tractor models 1010, 1020, 1520, 1530, 2010 serial number 42001 and up, 2020, 2030, 2040, 2150, 2250, 2155, 2355, 2240, 2350, 2550, 2355, 2555, 2440, 2510, 2520, 2630, 2640, 2750, 2755, 2855, 2840, 2940, 2950, 2955, 3010, 3020, 3055, 3255, 3155, 4000, 4010, 4020, 4320, 4520, 4620, 5010, 5020, 6030, 7020, 720, 730, 820, 830, 840, 8440, 8640, 8630. (Part No: AR27977)
$10.26

Oil Pump Drive Shaft Coupling - For tractor models A series after sn 424025, B series, G series, 50, 60, 70 gas, 520, 530, 620, 630, 720 gas, 730 gas. (Part No: B250R)
$19.95

PTO / Driveline
Brake Plate, (PTO) - With facing. For tractor models 80, 620, 630, 720, 730, 820, 830. Replaces RE20727. (Part No: AF2768R)
$45.29

Clutch Disc, (PTO) - With Facing. For tractor models 50 serial number 5032350 and up, 60 serial number 6060700 and up, 70 serial number 7039400 and up, 80, 520, 530, 620, 630, 720, 730, 820, 830. Replaces RE29784. (Part No: AR1294R)
$16.13

Clutch Drive Disc (PTO) - 3.375" I.D., 5.625" O.D., .06" thickness, 6 tangs. For tractor models 50, 60, 70, 520, 530, 620, 630, 720, 730. Price is for each, you may need more than one depending on your application. (Part No: A5145R)
$11.63

Clutch Plate, (PTO) - 1.40" I.D., 5.00" O.D. .290" thickness. For tractor models 50 SN# 5032350 and up, 520, 530, 60 SN# 6060700 and up, 620, 630, 70 SN# 7039400 and up, 720, 730, 80, 820, 830. (Part No: RE29794)
$30.27

PTO Clutch Drum Inner Seal - This PTO Clutch Drum Inner Seal measures 1.125 inch inside diameter, 1.565 inch outside diameter, 0.250 inch wide. [50, 60, 70 (PTO Clutch Drum Inner Seal on following (Rowcrop, Orchard, HiCrop and Standard) with Engine driven live PTO) ], [ 520, 530, 620, 630, 720, 730 (PTO Clutch Drum Inner Seal on following (Rowcrop, Orchard, HiCrop and Standard) with Engine driven live PTO. Also used For Dual power control valve control arm seal.) ], [ 820 2 cylinder, 830 2 cylinder, 840 2 cylinder (Used For Dual power control valve control arm seal.)]; Replaces: AA5247R, AR1355R, AT11492, RE14867. (Part No: 195501M1)
$3.75

PTO Flipper Guard - For tractor models (50, 60, 70 with Live PTO/Live Hydraulics), 520, 530, 620, 630, 720, 730. (Part No: AA5288R)
$38.59

PTO Flipper Guard Spring - For tractor models (A from SN# 523600) and up, (B from SN# 149700), (G from SN# 43352), 50, 60, 70, 520, 530, 620, 630, 720, 730. (Part No: F711R)
$7.50

PTO Oil Seal - Fits John Deere - [A, AH, AN, ANH, AW, AWH (Used as a rear PTO oil seal (serial number 488000-UP)], [AO, AR (Used as a rear PTO oil seal serial number 260000 and up)], [B, BN, BNH, BW, BW40, BWH, BWH40 (Used as a rear PTO oil seal serial number 149700 and up)], [BO, BR (Used as a rear PTO oil seal serial number 333100 and up)], [G, GH, GM, GN, GW (Used as a rear PTO oil seal serial number 43352 and up)], [R, 50, 520, 530, 60, 620, 630, 70, 70D, 720, 720D, 730, 730D (used as a rear PTO oil seal)], 2010 (used as a transmission drive shaft seal), [3010, 4010 (Used as a front PTO oil seal)]; Replaces: AA2296R, AT11888, AT11931, AT16076. (Part No: 71701C1)
$9.93

PTO Shield - For 520, 530, 620, 630, 720, 730. PTO Shield replaces AR20482R. (Part No: R4406)
$62.79

PTO Shield Casting - For 520, 530, 620, 630, 720, 730. PTO Shield Casting replaces #AF2687R. (Part No: R4407)
$98.87

Paint
Paint, Classic Green, 1 Gallon - Green Paint for 2 cylinders include models A, AO, AR, B, BO, BR, C, D, GP, P, G, L, LA, H, M, MT, MC, Y, 62, R, 40, 50, 60, 70, 80, 320, 420, 520, 620, 720, 820, 330, 430, 530, 630, 730, 830, 435, 440, 840. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. PAINT NOTES: All paint is NON-RETURNABLE. Make sure you order the correct paint! Paint cannot be shipped to California due to California Regulations. All Paint can only ship GROUND UPS. (Part No: TP215GAL)
$62.40

Paint, Classic Green, 1 Quart - Green Paint for 2 cylinders include models A, AO, AR, B, BO, BR, C, D, GP, P, G, L, LA, H, M, MT, MC, Y, 62, R, 40, 50, 60, 70, 80, 320, 420, 520, 620, 720, 820, 330, 430, 530, 630, 730, 830, 435, 440, 840. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. PAINT NOTES: All paint is NON-RETURNABLE. Make sure you order the correct paint! Paint cannot be shipped to California due to California Regulations. All Paint can only ship GROUND UPS. (Part No: TP215QT)
$26.13

Paint, Classic Green, Aerosol, 6 Cans - ****ENTER 1 FOR A CASE OF 6 CANS. NOT SOLD INDIVIDUALLY.**** Green Paint for 2 cylinders include models A, AO, AR, B, BO, BR, C, D, GP, P, G, L, LA, H, M, MT, MC, Y, 62, R, 40, 50, 60, 70, 80, 320, 420, 520, 620, 720, 820, 330, 430, 530, 630, 730, 830, 435, 440, 840. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. PAINT NOTES: All paint is NON-RETURNABLE. Make sure you order the correct paint! Paint cannot be shipped to California due to California Regulations. All Paint can only ship GROUND UPS. (Part No: TP215SP)
$59.78

Seats
Arm Rests - Pair - Black Vinyl on Steel with Metal Frame Clip For A, B, D, G, R, 50, 60, 70, 80, 520, 530, 620, 630, 720, 730, 820, 830 (Part No: R1190)
$69.00

Arm Rests, Pair - Yellow Vinyl on Steel with Metal Frame Clip For A, B, D, G, R, 50, 60, 70, 80, 520, 530, 620, 630, 720, 730, 820, 830 (Part No: R1188)
$70.88

Backrest, Black - Superior, weatherproofed covers, material identical to cushions. Tee-nuts & cap screws included for easy installation. Holes are pre-set & drilled. Black. For tractor models A, B, G, 50, 60, 70, 520, 620, 720, 730, 820, 830 series (Replaces AR21965R) (19-1/2x5-1/4). (Part No: JT300B)
$42.49

Backrest, Yellow - This BACK REST ONLY has a weather resistant cover. Yellow. For tractor models A, B, G, 50, 60, 70, 520, 620, 720, 730, 820, 830 series (Replaces AR21966R) (19-1/2x5-1/4). JT300Y (Part No: R0173)
$39.00

Seat Adjust Handle - For 520, 530, 620, 630, 720, 730, 820, 830 with Float Ride Seat (Part No: R3889)
$30.71

Seat Back - Yellow, wood back. 6 inches high. For A, B, D, G, R, 50, 60, 80, 70, 520, 530, 620, 630, 720, 730, 820, 830. Picture shows seat bottom. Not included in price. Order P/N R0172 if needed. (Part No: R0173)
$39.00

Seat Back - Yellow, wood, 9 inches high. For A, B, D, G, R, 50, 60, 80, 70, 520, 530, 620, 630, 720, 730, 820, 830 (Part No: R0993)
$44.89

Seat Back - Black, wood, 6 inches high. For tractor models A, B, D, G, R, 50, 60, 80, 70, 520, 530, 620, 630, 720, 730, 820, 830. (Part No: R0864)
$39.00

Seat Bottom - Black, wood, 20 inches x 15 inches. For A, B, D, G, R, 50, 60, 80, 70, 520, 530, 620, 630, 720, 730, 820, 830 (Part No: R0863)
$46.92

Seat Bottom (Float Ride) - Yellow, wood. for 520, 530, 620, 630, 720, 730, 820, 830, 840 all with Float Ride only. This seat cushion measures 20-5/8 Inches by 14-1/2 Inches wide and 5 Inches tall. Order part number JT77Y if you want just a standard seat bottom. Replaces AF3270R (Part No: R0994)
$45.36

Seat Pin & Bushing Kit - For 520, 530, 620, 630, 720, 730, 820, 830 with Float Ride Seat (Part No: R2483)
$56.70

Seat Shock Absorber - For 520, 530, 620, 630, 720, 730, 820, 830. Seat shock absorber with bushings for tractor models with Float Ride Seat. Center to center extended is 13 inches, compressed 8 3/4 inches. Replaces AF3426R. (Part No: R2481)
$42.78

Seat Spring, Rubber - Right Hand For 50, 80, 520, 530, 620, 630, 720, 730, 820, 830 with Float Ride Seat. (Part No: AR39648)
$44.14

Seat Spring, Rubber - Left Hand For 50, 80, 520, 530, 620, 630, 720, 730, 820, 830 with Float Ride Seat. (Part No: AR39649)
$60.27

Seat Tie Bar Plate - This Seat Tie Bar Plate is for 520, 530, 620, 630, 720, 730, 820, 830 with Float Ride Seat (Part No: R3890)
$37.20

Sheet Metal / Body Parts
Battery Box - For 70, 720, and 730, all Gas. Battery Box. Made In USA. Also replaces AF3005R. Sheet metal parts may or may not come painted as pictured (unless the description states the color). They often come with only a primer coat of paint. (Part No: AF1597R)
$138.82

Battery Box - For 720, 730, 830 Diesel With Electric Start and Float Ride Seat. Inside Measures 18 3/4" x 15 1/8" x 9 1/2". Sheet metal parts may or may not come painted as pictured (unless the description states the color). They often come with only a primer coat of paint. (Part No: AR20196)
$126.88

Battery Box - With tool box door, for diesel models with Pony motor: 70, 720. Sheet metal parts may or may not come painted as pictured (unless the description states the color). They often come with only a primer coat of paint. (Part No: AF2077R)
$158.19

Fender - Right hand or left hand, fits either side. Clamshell style fender does NOT come with bracket for the following models: A, B, G, 50, 520, 60, 620, 70, 720 Diesel, 630, 730 Diesel. Additional $10 shipping due to weight. IF ORDERING ON-LINE, THIS ADDITIONAL CHARGE WILL BE ADDED TO YOUR ORDER AFTER YOUR RECEIPT IS PRINTED. Fender measures 27 3/4 tall and 33 inches wide at tallest and widest dimensions. Sheet metal parts may or may not come painted as pictured (unless the description states the color). They often come with only a primer coat of paint. (Part No: AA4655R)
$118.33

Fender, RH - For 520, 620, 720, 530, 630, 730. Fender, RH, without Hand Hole. Two Light Holes. Sheet metal parts may or may not come painted as pictured (unless the description states the color). They often come with only a primer coat of paint. Additional $20 shipping due to weight. IF ORDERING ON-LINE, THIS ADDITIONAL CHARGE WILL BE ADDED TO YOUR ORDER AFTER YOUR RECEIPT IS PRINTED. (Part No: AR20869)
$238.88

Grill Center Plate - With Clips - 1 1/2 Hole For 60 (From S#54500), 620, 630, 720, 730. Sheet metal parts may or may not come painted as pictured (unless the description states the color). They often come with only a primer coat of paint. (Part No: R2487)
$52.73

Grill Rod - For tractor models 60, 620, 630, 70, 720, 730. Sheet metal parts may or may not come painted as pictured (unless the description states the color). They often come with only a primer coat of paint. (Part No: A4317R)
$11.40

Grill Screen - For tractor models 60, 60 Standard after SN# 6043000, 620, 630, 70, 720, 730. Screen is 21.5 inches High X 14 Inches Wide. Sheet metal parts may or may not come painted as pictured (unless the description states the color). They often come with only a primer coat of paint. (Part No: A4316R)
$41.85

Platform Extension - Left Hand For 720 (To S#7214899) Standard. Sheet metal parts may or may not come painted as pictured (unless the description states the color). They often come with only a primer coat of paint. Replaces AF2805R (Part No: R4287)
$46.86

Platform Extension - Left Hand For 720 (From S#7214900), 730 Standard. Replaces OEM# AF3818R. Sheet metal parts may or may not come painted as pictured (unless the description states the color). They often come with only a primer coat of paint. (Part No: R4288)
$48.38

Platform Extension - Right Hand For 720, 730 Standard. Replaces OEM# AF2807R. Sheet metal parts may or may not come painted as pictured (unless the description states the color). They often come with only a primer coat of paint. (Part No: R4289)
$47.13

Step Pad - For tractor models 1020, 1120, 1520, 1530, 1830, 2010, 2020, 2030, 2040, 2120, 2130, 2150, 2155, 2240, 2350, 2355, 2440, 2510, 2520, 2550, 2555, 2630, 2640, 2750, 2755, 2840, 3010, 3020, 4000, 4010, 4020, 4050, 4230, 4240, 4250, 4255, 4320, 4430, 4440, 4520, 4620, 50, 5010, 5020, 520, 530, 60, 6030, 620, 630, 70, 720, 730, 80, 8020, 820, 830, 8450, 8650, 8850, 920, A, B, G (Part No: F3195R)
$30.00

Step Pad - For tractor models A, 60, B, 50, G, 520, 530, 620, 630, 70, 720, 730, 80, 820, 830, 2010, 1520, 1530, 2040, 2150, 2155, 2240, 2020, 2510, 2520, 2030, 2440, 3020, 2350, 2355, 2550, 2555, 2750, 2755, 2630, 2640, 4010, 3120, 4020, 2840, 4050, 4000, 4230, 4320, 4520, 4620, 4430, 4240, 4440, 4250, 4255, 5010, 5020, 6030, 8650, 920, 1120, 8850, 2130, 8450, 2120, 1830, 8020. (Part No: F3195R)
$30.00

Step with Bracket - Fits A, AO, AR, B, BO, BR, G, 50, 60, 70, 520, 530, 620, 630, 720, 730. Replaces OEM# A5234R or F3195R. Sheet metal parts may or may not come painted as pictured (unless the description states the color). They often come with only a primer coat of paint. (Part No: R2098)
$57.23

Toolbox - With Bracket For 720 (From S#722600), 730Diesel with Electric Start. OEM# R20216R. Sheet metal parts may or may not come painted as pictured (unless the description states the color). They often come with only a primer coat of paint. (Part No: R4272)
$60.80

Toolbox Cover with Hinge - Grated top. For tractor models 60, 70, 620, 630, 720, 730. (standard models). Sheet metal parts may or may not come painted as pictured (unless the description states the color). They often come with only a primer coat of paint. (Part No: R4774)
$47.13

Toolbox Cover with Hinge - Smooth top. For tractor models 60, 70, 620, 630, 720, 730. (standard models). Sheet metal parts may or may not come painted as pictured (unless the description states the color). They often come with only a primer coat of paint. (Part No: R4775)
$46.86

Toolbox Side - Fender Mount. For tractor models 60, 620, 630, 70, 720, 730 Standard. Sheet metal parts may or may not come painted as pictured (unless the description states the color). They often come with only a primer coat of paint. (Part No: R4271)
$44.66

Steering
Center Pivot Housing with Bushing - For tractor models 50, 520, 530, 60, 620, 630, 70, 720, 730 all with square tube axle only. Center Pivot Housing with Bushing. Add $35.00 additional shipping cost for this item due to weight. IF ORDERING ON-LINE, THIS ADDITIONAL CHARGE WILL BE ADDED TO YOUR ORDER AFTER YOUR RECEIPT IS PRINTED. (Part No: AA5765R)
$403.93

Drag Link End Assembly - This Drag Link End Assembly is for 50, 60, 70, 520, 530, 620, 630, 720, 730. OEM# C838R, C840R, H982R (Part No: R3849)
$55.20

Drag Link Rod - Threaded on one end, 7/8 inch inside diameter, right hand threads. For 60, 70, 620, 630, 720, 730 with Adjustable Round Front Axle. Replaces OEM B2696R. (Part No: R3850)
$43.31

Inner Tie Rod - For 520, 520, 620, 630, 720, 730. Inner Tie Rod. 16" long, 6 vertical holes. REPLACES: AF3206R (Part No: F3624R)
$101.39

Outer Tie Rod - For tractor models 520, 620, 630, 720, 730. InnerOuter Tie Rod. 17.75" long, 7 vertical holes. REPLACES: AF3207R (Part No: F3625R)
$125.03

Power Steering Fill Hole Plug - For 50, 60, 70, 80, 520, 530, 620, 630, 720, 730, 820, 830. Power Steering Fill Hole Plug, Metal. (Part No: R2480)
$9.98

Short Tie Rod - Short Tie Rod, Dimensions A-3.350 inch B-.687 inch, 18 LH thread. For JD 520, 530, 620, 630, 720, 730 tractors (Part No: AR21945)
$19.06

Spindle - Spindle, LH/RH, Dimension A-14.375 inch, B-1.5 inch, C-1.625 inch, D-1.312 inch. Fits A, AO, AR, B, G, GH, 50, 520, 530, 60, 620, 630, 70, 720 All with Factory Wide Fronts only. (Part No: AA5789R)
$242.31

Steering Arm - Left - For tractor models 520, 530, 620, 630, 720, 730. Steering Arm - Left. 1.5" Diameter, 6 Spline. (Part No: F3175R)
$146.49

Steering Arm - Right - For tractor models 520, 530, 620, 630, 720, 730. Steering Arm - Right. 1.5" Diameter, 6 Spline. (Part No: F3174R)
$146.49

Steering Wheel - 18" diameter, 7/8" splined hub, American Made Rubber, shiny bake-o-light. For tractor models 520 SN# 5208100 & up, 530, 620 SN# 6213100 & up, 630, 720 SN# 7214900 & up, 730, 820 SN# 8203100, 830. All with power steering. (Part No: AF3856R-R)
$69.00

Steering Wheel - For A, B, D, G, R, 50, 60, 70, 80, 520, 620, 630, 720, 730, (820 Diesel (2 CYL) With Power Steering). Steering Wheel 17 5/8" Diameter, 13/16" Keyed Hub. 2447R (Part No: AA380R)
$42.78

Steering Wheel - For R, 70, 720, 80, 820 Without Power Steering. Steering Wheel, 20" Diameter, 4 Spokes, 11/16" Keyed Hub. (Part No: AR505R)
$40.42

Steering Wheel - This steering wheel is for tractor models 520, 530, 620, 630, 720, 730, 80, 820, 830 with Power Steering. 18" Diameter, 7/8" Splined Hub, Plastic Covered Foreign made. 2 7/16 cap opening. (Part No: AF3856R-P)
$44.87

Steering Wheel Acorn Nut - Stainless steel. For tractor models 50 SN# 20400 and above, 60 SN# 37000 and above, 70 SN# 13000, and above, 520 SN# 8099 and below, 620 SN# 13099 and below, 720 SN# 14899 and below, 80, 820 SN# 3099 and below. (Part No: F1745R)
$14.25

Steering Wheel Cap - This 2 legged deer, correct cap for many covered steering wheels on JD models from 1968-2000. Fits a 2 7/16 inch opening. Replaces AL118173, AL155227, R47998 (Part No: AL155227)
$32.76

Steering Wheel Cap - For tractor models 320, 330, (420 with slant steering to SN# 139999), 430, 435, (520 from SN# 5208100 with power steering), (530, 630, 730 with power steering), (830 2-cyl with power steering), (620 from SN# 6213100 with power steering), (720 from SN# 7214900 with power steering), (820 2-cyl from SN# 8203100 with power steering). (Part No: R3859)
$46.07

Steering Wheel Nut - This steering wheel nut fits the following tractor models: 1020, 1520, 1530, 2020, 2030, 2040, 2150, 2240, 2255, 2350, 2440, 2510, 2520, 2550, 2630, 2640, 2750, 2840, 2940, 2950, 3010, 3020, 4000, 4010, 4020, 4030, 4040, 4050, 4230, 4240, 4250, 4320, 4430, 4440, 4450, 4520, 4620, 4630, 4640, 4650, 4840, 4850, 5010, 5020, 520, 530, 6030, 620, 630, 7020, 720, 730, 7520, 820, 830, 8430, 8440, 8450, 8630, 8640, 8650, and 8850. It measures 0.75 inches wide, 0.444 inches tall, and has a 16 NF thread size. Replaces part numbers: 14H482, 14H798, and 14H904. (Part No: 353435X1)
$0.44

Steering Wheel Plate - Fits John Deere 50 SN# #5020400 & up, 60 SN# #6037000 & up, 70 SN# #7013000 & up, 520 up to SN# #5208099, 620 up to SN# #6213099, 720 up to SN# #7214899, 80 & 820 up to SN# #8203099 (All with Power Steering), Replaces #F1744R (Part No: F1744R)
$17.85

Tie Rod Right Hand - Tie rod end, outer, threaded, right handed threads, 3-3/8 to center of post. For adjustable front axles 48 to 80 on tractors 520, 530, 620, 630, 720, 730. Fixed standard axles on tractors, 620, 630, 720, 730~ 820 and 830 except Mannheim. Also used on d For 520, 530, 620, 630, 720, 730, 820, 830 (Part No: TP-AR21944)
$23.33

Wheels
Bearing Cone - Outer bearing cone. For tractor models 50, 60, 70, 520 with 48-80 adjustable or 38 fixed thread~ 620, 630, 720 and 730 excluding roll-o-matic, 3010 and 3020 with 38 fixed thread, 4010 with 38 fixed thread. For 620, 630, 70, 720, 730 (Part No: 2790)
$15.21

Bearing Cone - For tractor models 3010, 3020, 4010, 50, 520, 60, 620, 630, 70, 720, 730, A, BW, D, G. (Part No: 3383)
$46.40

Bearing Cone - Inner bearing cone. For model applications: A series excluding AN, BW, D, G series~ 50~ 60~ 70. For 3010, 3020, 4010, 50, 520, 60, 620, 630, 70, 720, 730, A, BW, D, G (Part No: TP-JD7224)
$43.93

Bearing Cup - For tractor models 3010, 3020, 4010, 50, 520, 60, 620, 630, 70, 720, 730, A, BW, D, G. (Part No: 3320-TIM)
$17.50

Bearing Cup - Outer bearing cup. For model applications: A series excluding AN, BW, D, G series~ 50, 60, 70. For 1010, 2010, 2510, 3010, 3020, 4010, 4020, 4040, 4520, 4620, 4630, 4640, 4840, 50, 5020, 520, 530, 60, 6030, 620, 630, 70, 720, 730, A, AN, ANH, B, BN, BNH, BO, BR, BW, D, G (Part No: TP-JD7266)
$6.71

Bearing Cup, Inner - For tractor models A series excluding AN, BW, D, G series~ 50~ 60~ 70, 3010, 3020, 4010, 50, 520, 60, 620, 630, 70, 720, 730, A, BW, D, G. (Part No: TP-JD7270)
$17.50

Front Wheel Felt Retainer - The Felt Retainer is used with ``FW109S wheel bearing kit. 3.160Inch Diameter OD, 3.086 Inch ID, Thru hole 2.06 Inch Diameter, Outer ring Diameter 3.654 Inches, 1.115 Inch Overall height. Measure Before Ordering. For model applications: A series excluding AN, BW, D, G series~ 50 adjustable to serial number 5019164~ 60 series to serial number 6034693~ 70 series excluding standard to serial number 7011652. For 3010, 3020, 4010, 50, 520, 60, 620, 630, 70, 720, 730, A, BW, D, G. (Part No: D635R)
$13.35

Wheel Bearing Kit - For A, B, D, G, 50, 520, 60, 620, 70, 720, 730, (AO, AR, GH, 530, 630, all with Factory Wide Fronts ONLY). Wheel Bearing Kit for 1 Wheel. Kit contains 1 each of the following p/n 3383, 3320, 2785, 2720, D636R. (Part No: WBKJD1)
$90.47



Accessories / Supplies
Auxiliary Heater, Universal - This universal auxiliary heater is used for tractor cabs, combines, backhoes, dozers, forklifts, etc. using 5/8 inch heater hose connections. Hot water forced air heat. Dimensions: 6-1/2 inches x 9-1/2 inches x 9 inches, steel powder coat housing with aluminum core. 3-speed high volume squirrel cage fan, 12-volt, 20, 000 BTU includes switch, brackets, instructions. (Part No: MIS3127)
$239.98

Brakes
Brake Rivet Tool - Used to rivet brake lining to existing shoe or band. Includes a tool to drive out the old rivets and a tool to peen the new rivet, mounts into a vice, 1-1/4 inch throat, 1/8 inch diameter rivet punch. (Part No: RIVET_TOOL)
$33.95

Brake Rivet Tool, Large - Larger version of our Brake rivet tool. 3-3/8 inch deep throat x 2-1/8 inch high throat. Includes 1 punch for brake shoe rivets and 1 punch for clutch pulley brake. (Part No: LGRIVET)
$86.25

Cooling System
Magnetic Block Heater - Universal. Magnetic utility heater. 120 volt AC, 200 Watts. Built-in thermostat maintains optimum temperature - will not exceed 250 degree F (121 degree C). Quick-grip handle protects hands from heat. 4-3/8 inches (11cm) length, 2-1/2 inches (6.3cm) width, 3 inches (7.5cm) height (including handle). (Part No: MBH1153)
$63.94

Radiator Drain Tap - This drain tap fits various tractor models as a radiator, engine block, and hydraulic drain tap. This is 1/4 inch NPT 18 thread. Please verify size and thread count before ordering. Replaces: AM2780T, AM292T, AT13740. (Part No: C9NN8115A)
$2.79

Zip Leak - Industrial Radiator Stop Leak - A professional strength stop leak for tractors, trucks and construction equipment. Designed for large, heavy duty cooling systems. 5 oz. Bottle. Instructions/Usage: For average antique tractors (120-160 CID engines) use 1/4 bottle for 15 minutes, if the leak fails to stop, add an additional table spoon. (Part No: Z14012)
$10.23

Decals and Emblems
2 Legged Deer Decal - John Deere Leaping 2-Legged Deer, 3 1/2" x 4" black & silver, vinyl cut. (Part No: R4697)
$9.77

2 Legged Deer Decal - John Deere Leaping 2 Legged Deer, 2 1/2" x 3", black & yellow, vinyl cut. (Part No: R4696)
$9.77

2 Legged Deer Decal - John Deere Leaping 2-Legged Deer, 2" x 2 1/2", black & yellow, vinyl cut (Part No: R4695)
$9.77

2 Legged Deer Decal - John Deere leaping 2 legged deer, 6" black with yellow deer on vinyl. (Part No: R5186)
$16.28

2 Legged Deer Decal - John Deere leaping 2 legged deer, 6" yellow with black deer on vinyl. (Part No: R5187)
$16.28

2 Legged Deer Decal - John Deere leaping 2 legged deer, 9" yellow with black deer on vinyl. (Part No: R5188)
$27.24

2 Legged Deer Decal - John Deere leaping 2 legged deer, 6" black with silver deer on vinyl. (Part No: R5189)
$16.28

4 Legged Deer Decal - "John Deere Quality Farm Equipment" 10" on vinyl. (Part No: R5184)
$33.52

4 Legged Deer Decal - Says "John Deere Quality Farm Equipment + Parts and Service" with leaping 4 legged deer, 10" on vinyl. (Part No: R5185)
$33.52

Loader Decal, Yellow - Universal John Deere loader decal, 2" x 24". (Part No: JDL2Y)
$15.58

Drive Train
Lucas Hub Oil (quart) - Lucas Hub Oil was formulated to stop leaks in steering axles and trailer hubs on heavy duty trucks. It also allows hubs to run on a marginal amount of oil in case of a blown seal or poor maintenance. It is an excellent gear lube for racing or heavy duty applications. Key benefits slows leaks, prevents downtime, extremely heat resistant, Very long lasting. (Part No: LU10088)
$10.56

Electrical System
Alternator - Don't see the Alternator you need for your tractor? We have many alternators not listed on this website (for tractors 1953 & newer). Just call us at 800-853-2651. NOTE

Alternator Base Bracket Kit - Universal - Universal Base Bracket Mounting Kit. For converting from a generator to an alternator. Contains: brackets, bolts, washers, nuts and basic instructions. (Part No: 2348258)
$33.75

Alternator Top Adjusting Bracket, Universal - This Universal Top Adjusting Bracket for Alternator or Generator is 7/8 inches wide, 1-1/2 inch offset, 8-1/4 inch from farthest end of slot to center of mounting hole, 3-3/4 inch slot length, 3/8 inch mounting hole. (Part No: 8NL10302)
$11.93

Alternator, 12 Volt - Universal 63 Amp Delco Alternator. Single wire with built in regulator. Will fit most tractors pre 1980. (Part No: 8NE10305SE)
$78.59

Battery Hold Down - Universal hold down for batteries that measure 8 15/16 inches long and 6 13/16 inches wide. (Part No: NCA10718A)
$15.81

Battery Hold Down - Universal Battery Hold down. Verify your battery measurements. This will fit a 9 3/16 inches long and 7 3/16 inch wide battery. (Part No: 1111-0147)
$13.43

Battery Hold Down Bolts - Pair - These "J" bolts measure 10 1/2 inches long and are universal for many batteries. Verify length. Price is for a pair. (Part No: 393161R1)
$8.93

Battery Thermal Wrap - 60 Watt, 28 inches long wrap to keep your battery warm. (Part No: BTW28)
$35.98

Battery Thermal Wrap - 80 Watt, 36 inches long wrap to keep your battery warm. (Part No: BTW36)
$37.48

Battery Thermal Wrap - 160 Watt, 36 inches long wrap to keep your battery warm. (Part No: BTW72)
$53.81

Coil - This universal automotive style coil is 28, 000 volts for a 12 volt system, 2.9 ohms. Measures 6 inches long and 2 1/2 inches diameter. (Part No: 28010)
$28.97

Coil - Universal 12V - Universal coil fits many models. This Coil comes with an external resistor which can be removed if you need a coil with no resistance. Also comes with a mounting bracket. Coil is designed to be used on a 12 volt tractor system with the resistor or 6 volt without the resistor. Replaces: AA4879R, AA4983R (Part No: D5TE12029AB)
$7.13

Coil Bracket - Universal Coil Bracket (Part No: R1940)
$3.57

Coil, High Performance (Black), 12 Volt, Epoxy Filled - Epoxy filled coils provide superior winding support for high vibration environments. Pertronix Flame Thrower Black, high performance coil is for all 12-volt systems. Delivers up to 40, 000 volts. Enables larger plug gap for greater fuel efficiency and more power. Fits existing brackets. Coil has 3.0 Ohms of resistance. (Part No: 40611)
$41.59

Coil, High Performance (Black), 12 Volt, Oil Filled - Pertronix Flame Thrower heavy duty, high performance coil is for all 12-volt systems. Delivers up to 40, 000 volts. Oil filled for better cooling and voltage insulation. Enables larger plug gap for greater fuel efficiency and more power. Fits existing brackets. Coil has 3.0 Ohms of resistance. (Part No: 40511)
$35.88

Coil, High Performance (Black), 6 Volt, Epoxy Filled - Epoxy filled coils provide superior winding support for high vibration environments. Pertronix Flame Thrower Black, high performance coil is for all 6-volt systems. Delivers up to 40, 000 volts. Enables larger plug gap for greater fuel efficiency and more power. Fits existing brackets. Coil has 1.5 Ohms of resistance. (Part No: 40111)
$41.59

Coil, High Performance (Black), 6 Volt, Oil Filled - Pertronix Flame Thrower high performance coil is for all 6-volt systems. Delivers up to 40, 000 volts. Oil filled for better cooling and voltage insulation. Enables larger plug gap for greater fuel efficiency and more power. Coil has 1.5 Ohms of resistance. (Part No: 40011)
$35.88

Coil, High Performance (Chrome), 12 Volt, Epoxy Filled - Epoxy filled coils provide superior winding support for high vibration environments. Pertronix Flame Thrower Chrome, high performance coil is for all 12-volt systems. Delivers up to 40, 000 volts. Enables larger plug gap for greater fuel efficiency and more power. Fits existing brackets. (Part No: 40601)
$41.59

Coil, High Performance (Chrome), 12 Volt, Oil Filled - 12-VOLT, Pertronix Flame Thrower Chrome, high performance coil is for all 12-volt systems. Delivers up to 40, 000 volts. Oil filled for better cooling and voltage insulation. Enables larger plug gap for greater fuel efficiency and more power. Fits existing brackets. Coil has 3.0 Ohms of resistance. (Part No: 40501)
$40.32

Coil, High Performance (Chrome), 6 Volt, Oil Filled - 6-VOLT, Pertronix Flame Thrower Chrome, high performance coil is for all 6-volt systems. Delivers up to 40, 000 volts. Oil filled for better cooling and voltage insulation. Enables larger plug gap for greater fuel efficiency and more power. Fits existing brackets. Coil has 1.5 Ohms of resistance. (Part No: 40001)
$40.32

Coil, Ultra High Performance (Black), Epoxy Filled - Epoxy filled coils provide superior winding support for high vibration environments. Pertronix Flame Thrower II Black, ultra high performance coil is for 12-volt systems. Delivers up to 45, 000 volts, enables larger plug gap for greater fuel efficiency and more power. Fits existing brackets. (Part No: 45111)
$45.93

Coil, Ultra High Performance (Black), Oil Filled - Pertronix Flame Thrower II Black, ultra high performance coil is for 12-volt systems using "Ignitor II" electronic conversion kits or any 6 volt system. Delivers up to 45, 000 volts. Oil filled for better cooling and voltage insulation. Enables larger plug gap for greater fuel efficiency and more power. Fits existing brackets. (Part No: 45011)
$39.50

Coil, Ultra High Performance (Chrome), Oil Filled - Pertronix Flame Thrower II Chrome, ultra high performance coil is for 12-volt systems using "Ignitor II" electronic conversion kits or any 6 volt system using "Ignitor II". Delivers up to 45, 000 volts. Oil filled for better cooling and voltage insulation. Enables larger plug gap for greater fuel efficiency and more power. Fits existing brackets. Coil has 0.6 Ohms of resistance. For use with Ignitor II Electronic Ignition Module. (Part No: 45001)
$44.45

Distributor Cap, Wico - For All models using Wico distributor, clip type cap. (Part No: AT14190)
$44.75

Magneto Cap, 2 Cylinder - For tractor models using WICO XH magneto ONLY. (Part No: 1006501)
$50.88

Magneto, Wico XH & XHD, Service & Parts Manual - Wico XH And XHD magneto service instructions and parts list. This is a reprint of the original manual that has exploded views of all parts on the tractor with numbered pictures giving great detail on assembly and disassembly. It also gives you a guide with numbers for ordering parts. (Part No: MAG6)
$14.25

Spark Plug - Extended tip, 14mm thread, 3/4 inch reach. Replaces Champion N12YC. NOTE: Verify spark plug type before ordering. (Part No: AL65)
$2.73

Spark Plug - Extended tip, 14mm thread, 3/8 inch reach. Replaces Champion J10Y, J11Y, J12Y, J13Y. NOTE: Verify spark plug type before ordering. (Part No: AL85)
$2.73

Spark Plug - Standard tip, 7/8 inch-18 thread, 5/8 inch reach. Replaces Champion W10, W14, W18. NOTE: Verify spark plug type before ordering. (Part No: AL3076)
$4.63

Spark Plug - Standard tip, 14mm thread, .472" reach. Replaces Champion L9J, L10, L86, L86C, L88A, L90. NOTE: Verify spark plug type before ordering. (Part No: AL425)
$2.75

Spark Plug Wire Set, 4 Cylinder, Univeral - Universal Spark Plug Wire Set, 4 Cylinder, straight boot, cut to length. (Part No: S2097)
$12.75

Spark Plug Wire Set, 4 Cylinder, Universal - For use with high performance electronic ignition conversion kits. Kit has 90 degree sparkplug boots and straight distributor boots. (Part No: S.66442)
$12.59

Spark Plug Wire Set, Universal, 4 Cyl. - Universal Spark Plug Wire Set, 4 Cylinder, 90 degree boot, cut to length. Longest Reach is 33 inches. Solid brass distributor coils, Zinc-coated plug terminals, tin-coated copper core, boots constructed from EPDM rubber and dual-jacket insulation. Meets SAE J2031 Specifications. Made in the USA. (Part No: CPN12259)
$10.49

Spark Plug Wire Set, Universal, 6 Cyl. - Universal Spark Plug Wire Set, 6 Cylinder, 90 degree boot, cut to length, brass terminals, copper strand core. Longest Reach is 33 inches. (Part No: SWS260)
$15.00

Starter - Don't see the starter you need for your tractor? We probably have it! Just call us at 800-853-2651 with your make, model, engine cubic inches (CID) and number off your old starter and we will see if we can find it! (Part No: STARTER)
$0.00

Starter, Generator, Distributor Tag, 6 Volt, Blank - Comes with 2 rivets. 2.5" long, .800" wide, 2" center to center rivet hole, .150" dia. rivet holes. Customer must stamp numbers. (Part No: DELCO6)
$14.31

Stripper and Crimping Tool - Professional Fast and Easy tool for stripping and crimping electrical wires. (Part No: B1SB6718)
$21.20

Tag for Starter/Generator, 12 Volt, Blank - Comes with 2 rivets. 2.5" long, .800" wide, 2" center to center rivet hole, .150" dia. rivet holes. Customer must stamp numbers. (Part No: DELCO12)
$14.45

Engine Gaskets
Silicone Black RTV - Permatex black RTV silicone adhesive sealant. Provides a waterproof seal around metal, glass, rubber. Designed for indoor or outdoor use, 3 oz. tube. (Part No: PRM16BR)
$5.70

Silicone Blue RTV - Permatex ultra blue, no leak RTV silicone gasket, oil resistant, use on valve covers, oil pans, timing covers, water pumps. Temperature range -75 degree F to +500 degree F, 3.35 ounce tube. (Part No: PRM77BR)
$6.29

Silicone Copper RTV - Permatex ultra copper, hi-temp RTV silicone gasket. Three times more oil resistant than conventional silicone. Use on exhaust manifolds, valve covers, oil pans, water pumps. Temperature range -75° F to +700° F, 3 oz. tube. (Part No: PRM101BR)
$10.47

Engine Rebuild Kits
Lucas Assembly Lube - Lucas Assembly Lube (4 oz). Designed to be used as an initial lubricant to metal surfaces. It mixes with any oil and will not plug filters. This product clings to all surfaces and is an excellent rust inhibitor, allowing long term storage for all parts. It is useful wherever tension or torque is applied. Key Benefits are: Use to pre lube camshaft, bearings, lifters and valve train. Prevents seizing, galling and scuffing perfect for engine lding, super slick and tacky, easy to use, excellent rust inhibitor, excellent for long term storage, contains Zinc, Moly and other extreme pressure additives for maximum protection during engine break-in. (Part No: 10152)
$5.00

Engine Parts
Valve Overhaul Kits - Valve Overhaul Kits are located in the Engine Overhaul Kits Section (if available for this tractor). NOTE

Engine Rings
Piston Ring Sets - Don't see the correct ring set for your tractor? Give us a call and ask for a Hastings Ring Set (made in USA). We need the following information to correctly find the set you need: 1. Engine size & type (Ex: 233 CID Gas) 2. Number of engine cylinders, 3. Cylinder bore size, 4. Number and size of compression rings for each piston (Ex: (2) 3/32"), 4. Number and size of oil rings for each piston (Ex: (1) 5/32"). NOTE

Exhaust System
Chrome Exhaust Stack - This Chrome Stack is Single Wall, 48 inches long with a slotted, 2 inch inside diameter inlet. This is a universal part. Verify Measurements before ordering. (Part No: ZNL89020C)
$78.88

Chrome Exhaust Stack - This Chrome Stack is Single Wall, 48 inches long with a slotted, 2.5 inch inside diameter inlet. This is a universal part. Verify Measurements before ordering. (Part No: ZNL89025C)
$92.67

Chrome Exhaust Stack - This Chrome Stack is Single Wall, 48 inches long with a slotted, 2.75 inch inside diameter inlet. This is a universal part. Verify Measurements before ordering. (Part No: ZNL89027C)
$99.58

Chrome Exhaust Stack - This Chrome Stack is Single Wall, 48 inches long with a slotted, 3.00 inch inside diameter inlet. This is a universal part. Verify Measurements before ordering. (Part No: ZNL89051C)
$120.24

Chrome Exhaust Stack - This Chrome Stack is single wall, 53 inches long with a slotted, 3.00 inch inside diameter inlet with extended curve. This is a universal part. Verify measurements before ordering. (Part No: 146520CHR)
$112.10

Chrome Exhaust Stack - This Chrome Stack is Single Wall, 48 inches long with a slotted, 3.50 inch inside diameter inlet. This is a universal part. Verify Measurements before ordering. (Part No: ZNL89054C)
$115.52

Chrome Exhaust Stack - This Chrome Stack is Single Wall, 48 inches long with a slotted, 3.75 inch inside diameter inlet. It is 4 inches outside diameter beyond the inlet. This is a universal part. Verify Measurements before ordering. (Part No: ZNL89375C)
$144.46

Chrome Exhaust Stack - This Chrome Stack is single wall, 53 inches long with a slotted, 3.50 inch inside diameter inlet. It has an extended curve on the outlet. This is a universal part. Verify measurements before ordering. (Part No: 146490CHR)
$131.51

Chrome Exhaust Stack - This Chrome Stack is Single Wall, 48 inches long with a slotted, 4.00 inch inside diameter inlet. This is a universal part. Verify Measurements before ordering. (Part No: ZNL89057C)
$131.49

Chrome Exhaust Stack - This Chrome Stack is Single Wall, 48 inches long with a slotted, 5.00 inch inside diameter inlet. This is a universal part. Verify Measurements before ordering. (Part No: ZNL89485C)
$159.35

Chrome Exhaust System - This Chrome Stack is Single Wall, 42 inches long with a slotted, 2.50 inch inside diameter inlet. This is a universal part. Verify Measurements before ordering. (Part No: L102236CHR)
$84.28

Muffler Clamp, 1-1/2 - New Clamp for 1-1/2 inch outside diameter muffler inlet. (Part No: MC112)
$2.75

Muffler Clamp, 1-1/4 - New Clamp for 1-1/4 inch outside diameter muffler inlet. (Part No: MC114)
$3.98

Muffler Clamp, 1-1/8 - New Clamp for 1-1/8 inch outside diameter muffler inlet. (Part No: MC118)
$2.50

Muffler Clamp, 1-3/4 - New Clamp for 1-3/4 inch outside diameter muffler inlet. (Part No: MC134)
$2.75

Muffler Clamp, 1-3/8 - New Clamp for 1-3/8 inch outside diameter muffler inlet. (Part No: MC138)
$2.50

Muffler Clamp, 1-5/8 - New Clamp for 1-5/8 inch outside diameter muffler inlet. (Part No: MC158)
$2.93

Muffler Clamp, 1-7/8 - New Clamp for 1-7/8 inch outside diameter muffler inlet. (Part No: MC178)
$3.30

Muffler Clamp, 2 - New Clamp for 2 inch outside diameter muffler inlet. (Part No: MC200)
$2.64

Muffler Clamp, 2-1/2 - New Clamp for 2-1/2" outside diameter Muffler Inlet (Part No: MC212)
$3.30

Muffler Clamp, 2-1/4 - New Clamp for 2-1/4 inch outside diameter muffler inlet. (Part No: MC214)
$3.15

Muffler Clamp, 2-3/4 - New Clamp for 2-3/4 inch outside diameter muffler inlet. (Part No: MC234)
$4.50

Muffler Clamp, 3 - New Clamp for 3 inch outside diameter muffler inlet. (Part No: MC300)
$4.50

Muffler Clamp, 3-1/2 - New Clamp for 3-1/2 inch outside diameter muffler inlet. (Part No: MC312)
$4.75

Muffler Clamp, 3-1/4 - New Clamp for 3-1/4 inch outside diameter muffler inlet. (Part No: MC314)
$6.50

Muffler Clamp, 4 - New Clamp for 4 inch outside diameter muffler inlet. (Part No: MC400)
$7.50

Muffler Clamp, 4-1/2 - New Clamp for 4-1/2 inch outside diameter muffler inlet. (Part No: MC412)
$7.98

Muffler Clamp, 5 - New Clamp for 5 inch outside diameter muffler inlet. (Part No: MC500)
$7.98

Rain Cap - This rain cap is for a 1.50 inch pipe. (Part No: R1798)
$5.24

Rain Cap - This rain cap is for a 1.750 inch pipe. (Part No: R1799)
$5.33

Rain Cap - This rain cap is for a 2.0 inch pipe. (Part No: R1800)
$6.51

Rain Cap - This rain cap is for a 2.250 inch pipe. (Part No: R1801)
$7.23

Rain Cap - This rain cap is for a 2.50 inch pipe. (Part No: R1802)
$6.38

Rain Cap - This rain cap is for a 2.750 inch pipe. (Part No: R1804)
$10.02

Rain Cap - This rain cap is for a 3.0 inch pipe. (Part No: R1805)
$5.99

Rain Cap - This rain cap is for a 3.50 inch pipe. (Part No: R1806)
$11.99

Rain Cap - This rain cap is for a 4.0 inch pipe. (Part No: R1807)
$9.80

Rain Cap - This rain cap is for a 3.0 inch pipe. (Part No: R1805)
$5.99

Stainless Steel Clamp, 2 Inch - This Stainless Steel Clamp is used with Chrome Stacks and in other applications. (Part No: ZNL90869A)
$5.22

Stainless Steel Clamp, 2.5 Inch - This Stainless Steel Clamp is used with Chrome Stacks and in other applications. (Part No: ZNL90871A)
$5.54

Stainless Steel Clamp, 2.75 Inch - This Stainless Steel Clamp is used with Chrome Stacks and in other applications. (Part No: ZNL90872A)
$5.94

Stainless Steel Clamp, 3 Inch - This Stainless Steel Clamp is used with Chrome Stacks and in other applications. (Part No: ZNL90873A)
$5.57

Stainless Steel Clamp, 3.5 Inch - This Stainless Steel Clamp is used with Chrome Stacks and in other applications. (Part No: ZNL90874A)
$5.81

Stainless Steel Clamp, 4 Inch - This Stainless Steel Clamp is used with Chrome Stacks and in other applications. (Part No: ZNL90875A)
$6.09

Fuel System / Air Intake
Carburetor Elbow & Strainer - Fits various JD models. VERIFY FITTING DIMENSTIONS. Fits Marvel and some Carter UT Series carburetors. Used with flair fitting, not compression fitting. Male end (screen end) is 1/8 inch pipe threads. Female end is 1/4 inch flair. (Part No: 9N9553)
$4.83

Choke Cable - Universal choke cable 72 inches long, 7/16 inch thread diameter. Being a universal may or may not look like the picture. May say "Choke" or "C" or nothing. (Part No: CC72)
$11.58

Fuel Filter, In-Line, 1/4 inch - Inlet 1/4 inch, outlet 1/4 inch, outside diameter 1-29/32 inches, length 4-1/16 inches. (Part No: 6511393)
$4.44

Fuel Filter, In-Line, 3/8 inch - Inlet 3/8 inch, outlet 3/8 inch, outside diameter 1-29/32 inches, length 3-7/8 inches. (Part No: BF836)
$4.58

Fuel Filter, In-Line, 5/16 inch - Inlet 5/16 inch, outlet 5/16 inch, outside diameter 1-29/32 inches, length 4-5/32 inches. (Part No: BF840)
$4.14

Fuel Filter, In-Line, 5/16 inch - Inlet 5/16 inch, outlet 5/16 inch, outside diameter 1-29/32 inches, length 4-5/32 inches. (Part No: BF840)
$4.14

Fuel Filter, In-Line, 5/16 inch, Clear - Inlet 5/16 inch, outlet 5/16 inch, outside diameter 2-1/8 inches, length 3-21/32 inches. (Part No: BF7736)
$2.36

Fuel Tank Liner - For all fuel tanks. One quart Fuel Tank Liner covers tanks up to 12 gallons. Once cleaned, this tank liner will prevent further corrosion inside your tank. (Part No: R2043)
$33.23

Fuel Tank Liner Kit - Works on all metal gas tanks, use with gas or diesel fuels. Kit includes 1 qt cleaner, 1 qt prep solvent, and 1 qt tank liner which covers tanks up to 12 gallons. Includes application instructions. (Part No: NR1259)
$54.12

Fuel Tank Repair Kit - Permanent hole and crack repair for metal fuel tanks in 30 minutes. Kit includes instructions and materials needed to fix cracks up to 4 inches long and holes up to 3/8 inches in diameter. NOT for plastic fuel tanks. (Part No: FTR180)
$21.14

Fuel Tank Screen - This Fuel Tank Screen is used with most stem-type sediment bowls to further protect against debris in the gas line. It has a 0.216 inch Insert Pipe outside diameter - 2.53 inch Overall Length. (Part No: R7949)
$9.00

Fuel Tank Webbing, 3 Ft - Black woven nylon type material, .042 inches thick, 3 foot section. (Part No: FTW494)
$4.13

Lucas Fuel Treatment (quart) - Lucas Fuel Treatment is formulated for both gasoline and diesel engines, carbureted or fuel injected. It gives your fuel system what it really needs - a blend of super slick oils and additives with a high detergent action that allows the engine to operate at maximum efficiency. Also, it cleans and lubricates the carburetor and injectors and causes the fuel to burn more thoroughly for increased power and less fuel consumption. Lucas Fuel Treatment should definitely be used in vehicles that require leaded fuel because it actually replaces the benefits of lead in gasoline without causing harmful emissions. Use it to pass smog tests. Finally, it totally neutralizes the harmful effects of low sulfur diesel fuel.A powerful blend of oils and additives that contain no SOLVENTS. Designed to increase power and fuel mileage and also lower exhaust emissions through a more complete combustion. (Part No: LU10003)
$10.67

Marvel-Schebler Service Manual - This Service manual is a complete manual for all DLTX and TSX model carburetors. Comes with tractor carburetor principle of operation and overhaul step-by-step instructions. 21 Pages. (Part No: MAR_CARB_SV)
$9.95

Sediment Bowl Gasket, 2-1/8 inch - For bowls with 2-1/8 inch diameter, 2.150 inch outside diameter. Made in the USA. (Part No: C1778R)
$1.20

Stop Cable - This red knobbed Pull to Stop cable can be used as a stop cable, choke cable or any other functioning cable up to 72 inches in length. It does have a red pull knob that reads, "Pull to Stop". It has a usable cable length of 72 inches. (Part No: PTSTOP)
$7.79

Gaskets
Gasket Material, Cork Rubber - 3/32 inch thick x 12 inches wide x 24 inches long. For making general purpose gaskets. (Part No: GSKCR332)
$15.75

Gasket Material, Cork Rubber - 1/16 inch thick x 12 inches wide x 24 inches long. For making general purpose gaskets. (Part No: GSKCR116)
$8.93

Gasket Material, Exhaust Manifold - 1/16 inch thick x 12 inches wide x 28-1/2 inches long. Perforated steel core to make manifold gaskets. (Part No: GSKEM1228)
$20.40

Gasket Paper, .0160 - .0160 inch x 18 inches x 98 inches long. This gasket paper is for general purpose gasket making and NOT for high temperature applications. (Part No: GSKP1844)
$15.79

Gasket Paper, .0275 - .0275 inch thick x 18 inches wide x 98 inches long. This gasket paper is for general purpose gasket making and NOT for high temperature applications. (Part No: GSKP1898)
$24.15

Gauges
Ammeter Gauge - 60-0-60, 12 volt, 2 inch body diameter. Not illuminated. (Part No: AMG60)
$2.99

Hourmeter - DC voltages from 12 volt thru 36 volt nominal. Heavy duty glass-reinforced polyester body. Internal shock shields and grommets protect movement from shock and vibration damage. Fits 2-1/4 inch opening, three (3) mounting screws with nuts and two (2) blade terminals included. (Part No: HM771)
$46.42

Hourmeter, Analog - 2 inch, black. Can be used on any tractor with a 12 to 24 volt electrical system. (Part No: S.52672)
$38.40

Oil Gauge Copper Line Kit - Universal, for tractors using 1/8 inch x 6 foot copper oil line. Includes 6 foot 1/8 inch line, 2 inch x 5/16 inch-24 UNF nuts, 2 compression sleeves, and a 1/8 inch-27 NPTF female to 5/16 inch-24 UNF male adapter. (Part No: UNI523)
$25.20

Oil Line Adapter - Oil Gauge fittings may be different even for the same models. Here is an Oil Line Adapter if you have a gauge line without removable fittings, this converts 1/8 inch pipe thread to 1/8 inch tube. Brass. (Part No: 919095)
$13.95

Oil Line Adapter - Oil Gauge fittings may be different even for the same models. Here is an Oil Line Adapter if you have a gauge line without removable fittings, this converts 1/8 inch pipe thread to 1/4 inch tube. Brass. (Part No: IHS626)
$12.95

Oil Pressure Gauge - Universal Complete assembly with oil tube and mounting hardware. 80 psi. Line uses 1/4 inch connection with adapters for 3/8 and 1/2 inch. (Part No: SSW0002)
$8.62

Temperature Gauge - Universal water temperature gauge (0-280 degree scale). Fits tractor model using 2 inch gauge. Comes with 70 inch capillary tube and will fit a 1/2 inch or 3/4 inch male adapter, engine block or radiator threaded hole. (Part No: 1042944)
$23.78

Temperature Gauge, Universal - For 2 inch mounting hole. Complete assembly with bracket and adapters for block. Fitting for lead is 3/8 inch NPT and 1/2 inch NPT adapter. Install in block, head or hose. Temperature is measured in 3 zones (COLD, NORMAL, HOT). Black face with white needle. Extra-long 77 inch capillary line. Fits all liquid cooled engines. (Part No: UTG50)
$16.20

Temperature Gauge, Universal - Heat indicator for 2 inch hole. Complete assembly with bracket and adaptors. Numeric Face. Install in block, head or hose. Dial calibrated to 250 degrees. 70 inch metal wrapped capillary line. (Part No: UTG25)
$22.02

Hitch / Drawbar
Center tube, Stablizer - Center tube for SK102CH stabilizer kit. (Part No: SK102CH-CT)
$13.66

Check Chain & Pin Kit - Includes 1 Chain and 2 Clevis with pins and cotters. For most early models, pre-1965, category 1. (Part No: CBPN598A)
$12.09

HAIR PIN ASSORTMENT - 15-piece assortment. Includes four(4) of HP-3 (wire diameter 3/16 inch, length 3.75 inches), four(4) of HP-4 (wire diameter 5/32 inch, length 2 15/16 inches), four(4) of HP-5 (wire diameter 1/8 inch, length 2 9/16 inches), and three(3) of HP-6 (wire diameter 3/32 inch, length 1 5/8 inches). (Part No: HPA15X)
$5.99

HITCH BALL 10000LB 2-5/16 - 2-5/16 inch BALL SIZE, 1-1/4 inch STUD THREAD, 2-1/2 inch STUD LENGTH, 10000 LB MAX LOAD CAPACITY, THREE CHROME HITCH BALL CLASS. (Part No: CHB2516114)
$23.85

HITCH BALL 15000LB 2-5/16 - 2-5/16 inch BALL SIZE, 1-3/8 inch STUD THREAD, 2-5/8 inch STUD LENGTH, 15, 000 LB MAX LOAD CAPACITY, THREE CHROME HITCH BALL CLASS. (Part No: CHB2516138_)
$25.04

HITCH BALL 2000LB - 1-7/8 BALL SIZE, 3/4 STUD THREAD, 1-3/4 STUD LENGTH, 2000 LB MAX LOAD CAPACIRY, ONE CHROME HITCH BALL CLASS. (Part No: CHB17834)
$13.37

HITCH BALL 3500LB - Hitch ball. 2 inch ball size, 3/4 inch stud thread, 1-7/8 inch stud length, 3500 lb. max load capacity, one/two chrome hitch ball class. (Part No: CHB234)
$9.48

HITCH BALL 5000LB - Hitch ball. 2 inch ball size, 1 inch stud thread, 2-1/8 inch stud length, 5000 lb. max load capacity, two chrome hitch ball class. (Part No: CHB21)
$10.83

HITCH BALL 5000LB 2-5/16 - Hitch Ball, 2-5/16 inch ball size, 1 inch stud thread, 2 inch stud length, 5000 lb. max load capacity, three chrome hitch ball class. (Part No: CHB25161)
$15.39

LINCH PIN, 10 Pack - Package of 10 linch pins. Pin diameter 5/16 inch, useable length 1 1/4 inch, Ring diameter 1 5/8 inch. Cold Forged. Enter 1 for package of 10. (Part No: DKP516)
$4.28

Lift Arm Bushing - This Bushing is for using Category I Implements with Category II Lower Lift Arms. It has a 7/8 Inside Diameter, and 1-1/8 Outside Diameter and is 1-3/4 Inches long. Replaces B500192, 87299215, 87760407, EC0NG992AA, 150-821, BUSH04, 22BCO006, 477RB, BO821, 2430351, B821, B2008, 351, 00351, C7NNG992A, 81819374 (Part No: BUSH04)
$1.25

Linch Pins, Pack of 10 - Pin diameter 1/4 inch, useable length 1 1/4 inch. Cold Forged. Enter 1 for package of 10. (Part No: DKP14)
$2.55

Linch Pins, Pack of 10 - Package of 10 linch pins. 7/16 inch diameter pin x 1-3/4 inch usable length, 1-5/8 inch diameter ring. Enter 1 for package of 10. (Part No: DKLP91)
$2.40

Linch Pins, Pack of 10 - Linch Pins. 3/16 inch outside diameter pin x 1-1/4 inches Long. ***Enter 1 for package of 10*** (Part No: DKP316)
$4.17

Quick Hitch, Category I - Comes assembled complete with hardware. Easier hookup, spring loaded locking device. Adjustable top link ball bracket. Includes 7/8 inch mounting pins and adapter bushings, 27-1/4 inches width, 3-1/2 inch x 3-1/2 inch beam. This is ONLY for tractors that have, a three point hitch already installed. An additional shipping charge of $60 will apply due to the weight of this item. IF ORDERING ON-LINE, THIS ADDITIONAL CHARGE WILL BE ADDED TO YOUR ORDER AFTER YOUR RECEIPT IS PRINTED. (Part No: HF141101)
$227.70

Universal Drawbar Lock - For CAT I drawbars only (drawbars that are 1 inch thick x 2-1/2 inch width) . Prevents drawbar from rotating. (Part No: 49A29)
$22.14

Universal Drawbar Lock - For Cat. 1 drawbars up to 1 1/2 inch thick and 3 inches wide. Prevents drawbar from rotating. (Part No: DBL2)
$27.60

Universal Stabilizer Chain Kit - Chain stabilizers, turnbuckle and chain links adapt to any size 3-point hitch, usually used on larger tractors. VERIFY MEASUREMENTS. CLICK ON PICTURE FOR MEASUREMENTS. Move clevis up or down chain links; use turnbuckle for final adjustment. Packed and sold in pairs, less brackets. (Part No: SK102CH)
$49.67

Hydraulic System
Hydraulic Parts, Universal - Universal hydraulic parts such as hoses, filters, pressure gauges etc.. can be found in the Accessories and Universal parts section. NOTE

Universal Pressure Gauge, Hydraulic - 400 lb Gauge. Glycerin Filled. Stainless Steel Case 2-1/2 diameter. Nickel Silver movement accurate to within 2%. Dual range KPA-PSI. Plexiglas Crystal. 1/4 NPT male brass fitting. (Part No: GG400)
$11.13

Implements
Axle Bolt - Axle bolt, 1 each (Ref 3). Used on many Bush Hog rotary cutters. Used on models 12, 104, 105, 109, 126, 205, 255, 275, 285, 305, 306, 307, 405, 405HR, 406, 406HR, 502, 600, 1050, 1051, 1109, 1126, 1207, 1209, 1226, 1306, 1307, 1405, 1406, 2510, 2512, 3108, 2309, BD90, FH162, S268, SM60, SQ36 (Part No: BH1317)
$14.00

Axle Nuts (5) - 5 Pack of Axle Nuts. Enter 1 for pack of 5. (Ref 4) Used on many Bush Hog rotary cutters. Used on models 12, 104, 105, 109, 126, 205, 255, 275, 285, 305, 306, 307, 405, 405HR, 406, 406HR, 502, 600, 1050, 1051, 1109, 1126, 1207, 1209, 1226, 1306, 1307, 1405, 1406, 2510, 2512, 3108, 2309, BD90, FH162, S268, SM60, SQ36 (Part No: 15622BH)
$1.69

Bearing Cup - This part fits Caster Assembly (Part Number BH215, Ref #6). Sold individually, two used per caster assembly. Used on many Bush Hog rotary cutters. Used on models 12, 104, 105, 109, 126, 205, 255, 275, 285, 305, 306, 307, 405, 405HR, 406, 406HR, 502, 600, 1050, 1051, 1109, 1126, 1207, 1209, 1226, 1306, 1307, 1405, 1406, 2510, 2512, 3108, 2309, BD90, FH162, S268, SM60, SQ36. Also replaces 132709, 15191, 32190M1, L44610. (Part No: 170BH)
$1.94

Bearing cone (L44643) - For Caster Assembly, requires 2.Used on many Bush Hog rotary cutters. Used on models 12, 104, 105, 109, 126, 205, 255, 275, 285, 305, 306, 307, 405, 405HR, 406, 406HR, 502, 600, 1050, 1051, 1109, 1126, 1207, 1209, 1226, 1306, 1307, 1405, 1406, 2510, 2512, 3108, 2309, BD90, FH162, S268, SM60, SQ36, SQ480, SQ600. (Part No: 22)
$6.30

Blade Bolt Kit - Price is for each bolt with hardware. Must be ordered in quantities of 2. For rotary cutter blade used on rotary cutters. Please verify dimensions before ordering: A = 1 1/8-12 inch, B = 3 1/2 inch, C = 1 3/8 inch, D = 1 inch, E = 9/16 inch, F = 1/2 inch, G = 2 1/2 inch, H = 1.492 inch (for 1 1/2 inch blade hole), I = 1.12 inches. (Part No: 63607)
$11.78

Bush Hog Axle Spacer Bushing - Used on the following Bush Hog cutters: 12, 104, 105, 109, 126, 205, 255, 275, 285, 305, 306, 307, 405, 405HR, 406, 406HR, 502, 600, 1050, 1051, 1109, 1126, 1207, 1209, 1226, 1306, 1307, 1405, 1406, 2510, 2512, 3108, 2309, BD90, FH162, S268, SM60, SQ36, SQ480, SQ600. Wheel must be attached to fork. For Bush Hog cutters. With SPB40 spacer, assembly will also replace all models with Timken Bearings (Ref #1-#11). (Part No: SPB40)
$4.91

Caster Assembly - Tail wheel and hub assembly with grease fitting and fork assembly. Shaft on Yoke is 1-1/2 inch diameter, 8 inches overall length, 7-1/4 inches to pin hole. New style tail assembly, used on the following Bush Hog cutters: 12, 104, 105, 109, 126, 205, 255, 275, 285, 305, 306, 307, 405, 405HR, 406, 406HR, 502, 600, 1050, 1051, 1109, 1126, 1207, 1209, 1226, 1306, 1307, 1405. Wheel must be attached to fork. For Bush Hog cutters with SPB40 spacer (included), assembly will also replace all models with Timken bearings. (Part No: 12269)
$176.32

Caster Assembly - Tail wheel and hub assembly with grease fitting and fork assembly. Shaft on Yoke is 1-1/2 inch diameter, 8 inches overall length, 7-1/4 inch to pin hole. New style tail assembly, used on the following Bush Hog cutters: 12, 104, 105, 109, 126, 205, 255, 275, 285, 305, 306, 307, 405, 405HR, 406, 406HR, 502, 600, 1050, 1051, 1109, 1126, 1207, 1209, 1226, 1306, 1307, 1405. Wheel must be attached to fork. For Bush Hog cutters with SPB40 spacer (included), assembly will also replace all models with Timken bearings. (Part No: 12269)
$176.32

Caster Assembly, Old Style - Tail Wheel and Hub Assembly with grease fitting. 4 x 8 inch rim, 15 inch outside diameter of wheel. Includes wheel, hub, axle bearing and bolt assembly. OLD style tail assembly used on the following Bush Hog cutters: 12, 104, 105, 109, 126, 205, 255, 275, 285, 305, 306, 307, 405, 405HR, 406, 406HR, 502, 600, 1050, 1051, 1109, 1126, 1207, 1209, 1226, 1306, 1307, 1405, 1406, 2510, 2512, 3108, 2309, BD90, FH162, S268, SM60, SQ36, SQ480, SQ600. Wheel must be attached to fork. For Bush Hog cutters. With SPB40 spacer, assembly will also replace all models with Timken Bearings (Ref #1-#11). (Part No: BH215)
$106.08

Graphite Lubricant - Dry Graphite Powder, 5 lb container, used to lubricate planter seed channels. Recommended application rate: 2 oz per box. Typically treats 25-30 acres. (Part No: TP99500GP)
$21.25

HUB with BRG CUPS - 4-bolt, 5 inch bolt circle and 3-5/8 inch wheel pivot hub with bearing cups (1 inch axle) (Ref #5). This part fits caster assembly (part number BH215). Used on many Bush Hog rotary cutters. Used on models 12, 104, 105, 109, 126, 205, 255, 275, 285, 305, 306, 307, 405, 405HR, 406, 406HR, 502, 600, 1050, 1051, 1109, 1126, 1207, 1209, 1226, 1306, 1307, 1405, 1406, 2510, 2512, 3108, 2309, BD90, FH162, S268, SM60, SQ36. (Part No: BH1311)
$44.80

Hub Assembly - Hub with bushings (3/4 inch), wheel bolts (4), and grease fitting. Center tube length 5 inches. For rotary cutters: RB60 with new style 1-1/4 inch diameter caster, SM60R, SM160R; Squealer models: 1207, SQ36, SQ48, SQ60, SQ72, SQ148, SQ480. Replaces 60978, 60990, 63812. Can use 500BH tail wheel. (Part No: 63813BH)
$28.38

Round Bale Tine 31.5 Inches - Fully Hardened. Also replaces Kverneland 221151. (Part No: 221129)
$44.70

Round Bale Tine 38.5 Inches - Fully Hardened. Also replaces Kverneland 241107, 241161. (Part No: 241100)
$77.06

Round Bale Tine 43 Inches - Fully Hardened. (Part No: 241166)
$97.46

Round Bale Tine 49 Inches - Fully Hardened. (Part No: 241162)
$100.37

Round Bale Tine 55 Inches - Fully Hardened. (Part No: 241163)
$109.42

Seal, Caster - Seal, 2 required (Ref #2). Used on many Bush Hog rotary cutters. Used on models 12, 104, 105, 109, 126, 205, 255, 275, 285, 305, 306, 307, 405, 405HR, 406, 406HR, 502, 600, 1050, 1051, 1109, 1126, 1207, 1209, 1226, 1306, 1307, 1405, 1406, 2510, 2512, 3108, 2309, BD90, FH162, S268, SM60, SQ36, SQ480, SQ600. (Part No: 30BH)
$5.56

Tail Wheel Assembly - 6 inch x 9 inch tail wheel assembly with laminated tire, less hub. 4 inch pilot, 5 bolt holes, 5-1/2 inch bolt circle. 5-1/4 inches wide, 21 inch outside diameter, 74#. Used mostly on pull Bush Hog models of the following series mowers: 109, 115, 126, 160, 166, 205, 206, 207, 220, 255, 256, 257, 268, 305, 306, 307, 310, 315, 405, 406, 502, 600, 1109, 1115, 1126, 1206, 1207, 1209, 1220, 1226, 1257, 1305, 1306, 1307, 1310, 1315, 1405, 1406, 1600, 2315, 2415, 2510, 2512, 2610, 2614, 2615, 3108, 3209, 3368, 3414, 3610, 4214, 4215, 12610, 12615, 13710, CR14R, CR20F. (Part No: 294)
$124.93

Talc Powder Lubricant - Dry Talc powder lubricant, 8 lb container. Absorbs moisture and keeps treated seed from sticking together in planter boxes. Recommended application rate: 3 oz. Coverage: Typically treats 60-80 acres. (Part No: TP19000TP)
$21.75

Lights
Halogen Work Light-Double Bulb - 12 volt lamp assembly, flood pattern, double bulb 55 watt halogen. Includes replaceable 55 watt halogen bulb. (Part No: L982-12V)
$51.42

Magnetic worklight Universal Mounting. - Can be placed anywhere there is a metal surface. 3-1/2 inch x 6 inch weather resistant steel body (black), glass lens, flood pattern, 140 foot beam. Halogen bulb, 12 volt, 55 watt, replaceable. 12 foot cord with cigarette lighter plug. (Part No: L100MAG)
$43.12

Portable Halogen Work Lamp - 3 inch x 5 inch sealed beam unit, 12 volt, 50 watt, 4 amp. With handle and magnetic base. Projects flood beam pattern 50 foot wide x 30 foot long. Lamp is not legal for street use. (Part No: L200MAGH)
$75.13

Safety Light Amber - 12 volt amber safety light, 4-1/4 inch diameter, 3/8 inch diameter by 5/8 inch mounting stud. Does not include flasher. (Part No: S.61357)
$11.21

Work Lamp, HID, Flood Light - Universal high intensity discharge flood light, 35 watt Xenon H3 lamp, size 4.725 inch width X 4.330 inch height X 5.512 inch length, internal ballast, hardened glass lens, far longer life span than halogen. 3000 to 3500 hours versus 280 to 400, higher lumen output 3200 lumens versus 700-1000 for halogen bulbs. (Part No: WL8500-E)
$127.64

Work Light 12V - Work light, 12 volt, 3000 candle power, trapezoidal light pattern. Uses 4-1/2" diameter sealed beam lamp, L4411. (Part No: L408-12V)
$41.40

Work Light 12V - Work light, 12 volt, 3000 candle power, trapezoidal light pattern. Uses 4-1/2" diameter sealed beam lamp, L4411. (Part No: L408-12V)
$41.40

Worklight 12 Volt - Red 12 Volt worklight with handle, on/off switch, swivels and rotates. (Part No: S.42792)
$29.92

Worklight 12 Volt Black - 12 Volt worklight with handle, on/off switch, swivels and rotates. Mounting holes measure 4 3/8 inch center to center. (Part No: S.67771)
$31.65

Miscellaneous
Cab Foam Kit - With Headliner 7-Piece - Black For tractor models with 1300 Series Hiniker Cab (Part No: R1235)
$294.33

Cab Foam Kit - With Headliner 10-Piece - Black For tractor models with QT1 Year Round Cab. Must be truck shipped - $75 will be added for shipping due to weight and size. *IF ORDERING ON-LINE, THIS ADDITIONAL SHIPPING CHARGE WILL BE ADDED TO YOUR ORDER AFTER YOUR RECEIPT HAS PRINTED. (Part No: R1236)
$346.95

Cab Foam Kit - 7-Piece - Black For tractor models with Hinson Cab. (Part No: R3247)
$333.80

Canopy - 60 inches wide x 65 inches long, molded from virtually indestructible flexible U.V. stabilized polyethylene, exclusive socket mounting system for torsion bars, no mounting bolts pass through molding. Available in green, white, orange, blue, or red. Please specify in comments section which color you need. Hardware to mount to your ROPS sold separately. Additional $150.00 shipping due to weight and size. IF ORDERING ON-LINE, THIS ADDITIONAL CHARGE WILL BE ADDED TO YOUR ORDER AFTER YOUR RECEIPT IS PRINTED. (Part No: B257X)
$430.31

Canopy Mounting Kit, 2 Post - Mounts the canopy to your 2 post ROP frames except Hoop Type Frame. We need the measurement of the top of the ROP and the size of the ROP Tubing used. Put sizes in the comments section of the order form. (Part No: B6603)
$75.80

Canopy Mounting Kit, 4 Post - Mounts the canopy to any 4 post ROP frame. (Part No: B6604)
$65.44

Canopy Mounting Kit, Hoop Type - Mounts the canopy to CURVED OR SQUARE TOP hoop type ROP frames up to 52 inches wide with leg thickness up to 4 inch x 2 inch. (Part No: B6602)
$110.28

Canopy, Small Tractors - 45 inches wide x 60 inches long. Molded from virtually indestructible flexible U.V. stabilized polyethylene, exclusive socket mounting system for torsion bars NO mounting bolts pass through molding. Available in white, green, orange, blue, and red please specify in comments section which color you prefer. Hardware to mount to your ROPS sold separately. Additional $150.00 shipping due to weight and size. IF ORDERING ON-LINE, THIS ADDITIONAL CHARGE WILL BE ADDED TO YOUR ORDER AFTER YOUR RECEIPT IS PRINTED. (Part No: B257XSTD)
$374.50

Deluxe Canopy, 3 Bow - Red. 3-Bow Deluxe Canopy. This sectional soft canopy with steel bows comes complete with cover and universal mounting brackets to fit on MOST fenders. Fits fendered wheel tractors, NOT including those with square fenders. 48 inch spread from Mounting brackets (41 inch spread at the top of canopy) Height is approximately 31 inch. (Part No: RFC100R)
$235.53

Deluxe Tractor Umbrella - Deluxe Umbrella comes with universal mounting bracket. Four spring steel bows are locked into place with individual spring clips, providing ease of operation and a rigid framework. Frame constructed of tubular steel. All metal parts are zinc plated for rust resistance. 54 inch square cover is made of durable polyester material. Each corner is double reinforced. AVAILABLE IN RED, YELLOW, ORANGE, WHITE or BLUE. State color desired in comments section of order form when ordering. (Part No: TU56-X)
$155.22

HAND CLEANER GALLON - Hand cleaner, with dispenser pump. 1 gallon plastic bottle. (Part No: PRM25218)
$28.72

Oil System
Lucas Heavy Duty Oil Stabilizer (quart) - A pure petroleum multi-use oil supplement. Controls noise, heat and wear in manual transmissions and differentials. Number one in the heavy duty and high performance industries. Lucas Oil Stabilizer is a 100% petroleum product formulated to eliminate dry starts and reduce friction, heat and wear in any type of engine. It allows motor oils a higher degree of lubricity which reduces oil consumption and operating temperatures. Use Lucas Oil Stabilizer in gear oil to stop leaks, reduce operating temperatures and increase the life of the gear oil. Since it is pure petroleum. Key Features Increase oil life at least 50% longer, Reduces oil consumption, Eliminates dry starts, Raises oil pressure, and Increases power and miles per gallon. (Part No: LU10001)
$15.12

PTO / Driveline
Driveline Assembly - AB4 series, complete drive shaft assembly with shielding and tractor and implement yokes. 1-3/8 inch 6 spline Q.D. tractor and implement yokes. 1333 mm (52-1/2 inch) overall length, end of yoke to end of yoke. 1110 mm (43-3/4 inch) compressed length center to center of cross bore. Cross and bearing kit is 27 mm 1.063 (1-1/16 inch) bearing diameter x 74.6 mm 2.940 (2-15/16 inch). 1333 mm (52-1/2 inch) overall length. ***VERIFY LENGTH BEFORE ORDERING*** (Part No: AB4111WY138)
$176.82

Driveline Assembly with Yokes - AB4 series, complete drive shaft assembly with shielding and tractor and implement yokes. 1-3/8 inch 6 spline Q.D. tractor yoke. 1-3/8 inch round bore with 1/2 inch pin hole implement yoke. 1300 mm (51 inch) overall length end of yoke to end of yoke. 1110 mm (43-3/4 inch) compressed length center to center of cross bore. Cross and bearing kit, 27 mm 1.063 (1-1/16 inch) bearing diameter x 74.6 mm 2.940 (2-15/16 inch) overall length (43-3/4 inch). Verify length before ordering. (Part No: AB4111WY)
$187.82

Driveline Assembly with Yokes - AB4 series, complete drive shaft assembly with shielding and tractor yoke, ratcheting torque limiter on implement end. 1-3/8 inch 6 spline Q.D. tractor yoke, 1-3/8 inch 6 spline ratcheting torque limiter with quick disconnect on implement end. 1372 mm (54 inch) overall length end of yoke to end of clutch. 1110 mm (43-3/4 inch) compressed length center to center of cross bore. Cross and bearing kit 27 mm 1.063 (1-1/16 inch) bearing diameter x 74.6 mm 2.940 (2-15/16 inch). 1372 mm (54 inch) overall length ***VERIFY LENGTH BEFORE ORDERING*** (Part No: AB4111K33)
$288.01

Overrun Coupler with Quick Release - This Overrun Coupler features a Quick Release. It fits applications needing a male and female end of 6 splines and 1 3/8 inches. (Part No: S.23639)
$69.41

PTO Safety Clutch, 40 HP - 1-3/8 inch 6 spline male and female ends, 6 inch diameter, 40 horse power capacity. Heavy duty unit allows PTO driven implements to freewheel with adjustable safety protection under load. Prevents expensive damage to internal tractor PTO packs. Prevents single clutch tractors from being driven forward by PTO over-run. (Part No: B9164)
$235.29

Paint
44 Minute DVD - How to Paint a Tractor - This DVD demonstrates the entire painting process including sanding, priming, body work, painting and decals. A John Deere B is used as the sample tractor, but the information will pertain to any make or model - the techniques are the same. Safety is also discussed. (Part No: JDV-02250)
$25.68

Acrylic Hardener, 16oz - This Acrylic Hardener is for all our Alkyd Enamel paint to be mixed with either gallons or quarts. Lead free. Improves initial dry time and hardness development. Not compatible with other fast dry enamel or other paints. This 8 ounce container mixes from 2 quarts to 1 gallon of unreduced paint. This product will greatly increase the paints anti-chip resistance and will add a slight gloss to the paint. (Part No: TP12P)
$40.53

Acrylic Hardener, 8oz - This Acrylic Hardener is for all our Alkyd Enamel paint to be mixed with either gallons or quarts. Lead free. Improves initial dry time and hardness development. Not compatible with other fast dry enamel or other paints. This 8 ounce container mixes from 2 quarts to 1 gallon of unreduced paint. This product will greatly increase the paints anti-chip resistance and will add a slight gloss to the paint. (Part No: TP12HP)
$22.04

Alumimum Hi-Heat Spray Paint - ****ENTER 1 FOR A CASE OF 6 CANS. NOT SOLD INDIVIDUALLY.**** 12 oz. spray can. Withstands heat up to 650 degrees for use on stacks and mufflers. PAINT NOTES: All paint is NON-RETURNABLE. Make sure you order the correct paint! Paint cannot be shipped to California due to California Regulations. All Paint can only ship GROUND UPS. (Part No: TP402HHSP_)
$53.49

Black Hi-Heat Spray Paint - ****ENTER 1 FOR A CASE OF 6 CANS. NOT SOLD INDIVIDUALLY.**** 12 oz. spray can. Withstands heat up to 650 degrees for use on stacks and mufflers. PAINT NOTES: All paint is NON-RETURNABLE. Make sure you order the correct paint! Paint cannot be shipped to California due to California Regulations. All Paint can only ship GROUND UPS. (Part No: TP411HHSP_)
$53.49

Dakota Prep & Shine, Twin Pack - Kit inlcudes (1) 16.oz bottle Dakota Prep with spray nozzle, (1) 16 oz. aerosol can Dakota Shine, (2) scrub pads (1) light, (1) aggressive. (Part No: DS2PK)
$42.18

Dakota Prep, 1 Gallon - Dakota Prep is a water-based and biodegradable cleaner that will remove wax buildup, grease, oxidation and grime from a variety of surfaces to renew paint to its previous luster. It is safe on many surfaces including painted surfaces, decals/vinyl lettering, plastics, fiberglass, clear coat finishes, aluminum, glass and rubber. (Part No: DP1G)
$79.35

Dakota Shine, 1 Gallon - Dakota Shine is a unique and patented product that will restore the color, lustre and value to faded and oxidized surfaces like paint, decals, plastics, fiberglass, engine compartments and more. The ingredients are designed to penetrate the surface to rejuvinate the pigments to their original, lime-new appearance. No mixing required, quick dry time and no overspray lines to buff out. Used in conjunction with Dakota prep for best results. (Part No: DS1G)
$109.61

Paint, Aluminum, 1 Gallon - From TISCO, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. PAINT NOTES: All paint is NON-RETURNABLE. Make sure you order the correct paint! Paint cannot be shipped to California due to California Regulations. All Paint can only ship GROUND UPS. (Part No: TP312GAL)
$49.36

Paint, Aluminum, 1 Quart - From TISCO, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. PAINT NOTES: All paint is NON-RETURNABLE. Make sure you order the correct paint! Paint cannot be shipped to California due to California Regulations. All Paint can only ship GROUND UPS. (Part No: TP312QT)
$21.66

Paint, Aluminum, Aerosol, 6 Cans - ****ENTER 1 FOR A CASE OF 6 CANS. NOT SOLD INDIVIDUALLY.**** From TISCO, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. PAINT NOTES: All paint is NON-RETURNABLE. Make sure you order the correct paint! Paint cannot be shipped to California due to California Regulations. All Paint can only ship GROUND UPS. (Part No: TP312SP)
$52.16

Paint, Clear Coat, 1 Gallon - From Tisco providing OEM quality. High strength air dry Acrylic laquer. Protects the original paint finish, adds more shine, prolongs color and prevents fade. Water clear non-yellowing gloss coat, smooth uniform film characteristics. PAINT NOTES: All paint is NON-RETURNABLE. Make sure you order the correct paint! Paint cannot be shipped to California due to California Regulations. All Paint can only ship GROUND UPS. (Part No: TP447GAL)
$76.42

Paint, Clear Coat, 1 Quart - High strength air dry Acrylic laquer. Protects the original paint finish, adds more shine, prolongs color and prevents fade. Water clear non-yellowing gloss coat, smooth uniform film characteristics. PAINT NOTES: All paint is NON-RETURNABLE. Make sure you order the correct paint! Paint cannot be shipped to California due to California Regulations. All Paint can only ship GROUND UPS. (Part No: TP447QT)
$30.93

Paint, Clear Coat, Aerosol, 6 Cans - ****ENTER 1 FOR A CASE OF 6 CANS. NOT SOLD INDIVIDUALLY.**** High strength air dry Acrylic laquer. Protects the original paint finish, adds more shine, prolongs color and prevents fade. Water clear non-yellowing gloss coat, smooth uniform film characteristics. PAINT NOTES: All paint is NON-RETURNABLE. Make sure you order the correct paint! Paint cannot be shipped to California due to California Regulations. All Paint can only ship GROUND UPS. (Part No: TP447SP)
$55.30

Paint, Gloss Black, 1 Gallon - High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. PAINT NOTES: All paint is NON-RETURNABLE. Make sure you order the correct paint! Paint cannot be shipped to California due to California Regulations. All Paint can only ship GROUND UPS. (Part No: TP550GAL)
$43.83

Paint, Gloss Black, Aerosol, 6 Cans - ****ENTER 1 FOR A CASE OF 6 CANS. NOT SOLD INDIVIDUALLY.**** High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. PAINT NOTES: All paint is NON-RETURNABLE. Make sure you order the correct paint! Paint cannot be shipped to California due to California Regulations. All Paint can only ship GROUND UPS. (Part No: TP550SP)
$45.50

Paint, Gray Primer, 1 Gallon - From TISCO, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. PAINT NOTES: All paint is NON-RETURNABLE. Make sure you order the correct paint! Paint cannot be shipped to California due to California Regulations. All Paint can only ship GROUND UPS. (Part No: TP2700GAL)
$50.40

Paint, Gray Primer, 1 Quart - From TISCO, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. PAINT NOTES: All paint is NON-RETURNABLE. Make sure you order the correct paint! Paint cannot be shipped to California due to California Regulations. All Paint can only ship GROUND UPS. (Part No: TP2700QT)
$20.58

Paint, Gray Primer, Aerosol, 6 Cans - ****ENTER 1 FOR A CASE OF 6 CANS. NOT SOLD INDIVIDUALLY.**** From TISCO, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. (Part No: TP2700SP)
$49.68

Paint, Green, 1 Gallon - From TISCO, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. PAINT NOTES: All paint is NON-RETURNABLE. Make sure you order the correct paint! Paint cannot be shipped to California due to California Regulations. All Paint can only ship GROUND UPS. (Part No: TP210GAL)
$57.29

Paint, Green, 1 Quart - From TISCO, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. PAINT NOTES: All paint is NON-RETURNABLE. Make sure you order the correct paint! Paint cannot be shipped to California due to California Regulations. All Paint can only ship GROUND UPS. (Part No: TP210QT)
$23.94

Paint, Green, Aerosol, 6 Cans - ****ENTER 1 FOR A CASE OF 6 CANS. NOT SOLD INDIVIDUALLY.**** From TISCO, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. PAINT NOTES: All paint is NON-RETURNABLE. Make sure you order the correct paint! Paint cannot be shipped to California due to California Regulations. All Paint can only ship GROUND UPS. (Part No: TP210SP)
$55.39

Paint, Industrial Yellow, 1 Gallon - High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. PAINT NOTES: All paint is NON-RETURNABLE. Make sure you order the correct paint! Paint cannot be shipped to California due to California Regulations. All Paint can only ship GROUND UPS. (Part No: TP530GAL)
$89.23

Paint, Industrial Yellow, 1 Quart - High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. PAINT NOTES: All paint is NON-RETURNABLE. Make sure you order the correct paint! Paint cannot be shipped to California due to California Regulations. All Paint can only ship GROUND UPS. (Part No: TP530QT)
$34.56

Paint, Industrial Yellow, Aerosol, 6 Cans - ****ENTER 1 FOR A CASE OF 6 CANS. NOT SOLD INDIVIDUALLY.**** High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. PAINT NOTES: All paint is NON-RETURNABLE. Make sure you order the correct paint! Paint cannot be shipped to California due to California Regulations. All Paint can only ship GROUND UPS. (Part No: TP530SP)
$55.30

Paint, JD Yellow, 1 Gallon - From TISCO, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. PAINT NOTES: All paint is NON-RETURNABLE. Make sure you order the correct paint! Paint cannot be shipped to California due to California Regulations. All Paint can only ship GROUND UPS. (Part No: TP190GAL)
$49.36

Paint, JD Yellow, 1 Quart - From TISCO, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. PAINT NOTES: All paint is NON-RETURNABLE. Make sure you order the correct paint! Paint cannot be shipped to California due to California Regulations. All Paint can only ship GROUND UPS. (Part No: TP190QT)
$21.66

Paint, JD Yellow, Aerosol, 6 Cans - ****ENTER 1 FOR A CASE OF 6 CANS. NOT SOLD INDIVIDUALLY.*** From TISCO, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. PAINT NOTES: All paint is NON-RETURNABLE. Make sure you order the correct paint! Paint cannot be shipped to California due to California Regulations. All Paint can only ship GROUND UPS. (Part No: TP190SP)
$49.27

Paint, Red Primer, Aerosol, 6 Cans - ****ENTER 1 FOR A CASE OF 6 CANS. NOT SOLD INDIVIDUALLY.**** From TISCO, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. PAINT NOTES: All paint is NON-RETURNABLE. Make sure you order the correct paint! Paint cannot be shipped to California due to California Regulations. All Paint can only ship GROUND UPS. (Part No: TP3987SP)
$45.46

Paint, Satin Black, 1 Gallon - From TISCO, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics.PAINT NOTES: All paint is NON-RETURNABLE. Make sure you order the correct paint! Paint cannot be shipped to California due to California Regulations. All Paint can only ship GROUND UPS. (Part No: TP225GAL)
$45.94

Paint, Satin Black, 1 Quart - From TISCO, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics.PAINT NOTES: All paint is NON-RETURNABLE. Make sure you order the correct paint! Paint cannot be shipped to California due to California Regulations. All Paint can only ship GROUND UPS. (Part No: TP225QT)
$18.84

Paint, Satin Black, Aerosol, 6 Cans - ****ENTER 1 FOR A CASE OF 6 CANS. NOT SOLD INDIVIDUALLY.**** From TISCO, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics.PAINT NOTES: All paint is NON-RETURNABLE. Make sure you order the correct paint! Paint cannot be shipped to California due to California Regulations. All Paint can only ship GROUND UPS. (Part No: TP225SP)
$59.78

Paint, Yellow Primer, 1 Gallon - From TISCO, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. PAINT NOTES: All paint is NON-RETURNABLE. Make sure you order the correct paint! Paint cannot be shipped to California due to California Regulations. All Paint can only ship GROUND UPS. (Part No: TP2720GAL)
$45.83

Slip Resistant Coating - Gallon can. For use in a variety of applications where slip resistance or sound deadening qualities are desired. Moisture and chemical resistant, helps protect against corrosion. Ready to use as is for easy application and touch up with brush or roller. Coverage area is 75 to 100 square feet. (Part No: BL116GAL)
$68.39

Slip Resistant Coating - Quart can. For use in a variety of applications where slip resistance or sound deadening qualities are desired. Moisture and chemical resistant, helps protect against corrosion. Ready to use as is for easy application and touch up with brush or roller. Coverage area is 19 to 25 square feet. (Part No: BL116QT)
$28.23

Slip Resistant Coating Kit - Do it yourself kit. Comes with one gallon of liner, mini roller with tray, two replacement roller covers, 2" brush, and sanding sponge. For use in a variety of applications where slip resistance or sound deadening qualities are desired. Moisture and chemical resistant, helps protect against corrosion. Ready to use as is for easy application and touch up with brush or roller. Coverage area is 75 to 100 square feet. (Part No: BL116KIT)
$99.22

Tire Paint, Black - Black tire paint (1 Quart)- The best way to make tires look like new. Our paint is a permanent water based paint that applies easily and dries quickly. It will not rub off even when wet. Gives dull, faded tires a non-glossy, like new finish. This paint is a concentrate which you dilute one-to-one with water. A little goes a long way! (Part No: E844Q)
$22.47

Tire Paint, Black - Black tire paint (1 Gallon)- The best way to make tires look like new. Our paint is a permanent water based paint that applies easily and dries quickly. It will not rub off even when wet. Gives dull, faded tires a non-glossy, like new finish. This paint is READY TO USE. (Part No: E844R)
$50.00

Tire Paint, Black - Black tire paint (1 Gallon)- The best way to make tires look like new. Our paint is a permanent water based paint that applies easily and dries quickly. It will not rub off even when wet. Gives dull, faded tires a non-glossy, like new finish. This paint is READY TO USE. (Part No: E844R)
$50.00

Seats
Pan Seat, Universal - 17 inch wide Gold zinc plated, 3-1/2 inch center to center on mounting holes, 1/2 inch by 1/2 inch center square. (Part No: B1865)
$33.63

Seat Belt - Universal Seat Belt. Can be adapted to many tractors. (Part No: RSB22)
$38.91

Seat Belt, Universal - Seat belt, universal 2-point static adjustable belt. Fits TS1110 seats. (Part No: TS1110BELT)
$17.79

Seat, Air Suspension, Black Leatherette, Universal - Seat, Deluxe AG Air suspension, Includes 12 volt compressor. Slides, fore/aft & lateral isolators, adj shock, seat top with Black Leatherette upholstery, lumbar, recline tilt –up & angle adjust armrests. *Adjustable backrest recline. *Infinitely adjustable mechanical lumbar support *Heavy duty 12 volt air compressor included. *DOUBLE LOCKING SLIDES, fore and aft isolators with lockout. *Ride firmness adjustment *Weight range 110-330 lbs. (Part No: TS5056V)
$1518.86

Seat, Air Suspension, Cloth, Universal - Seat, Deluxe AG Air suspension, Includes 12 volt compressor. Slides, fore/aft & lateral isolators, adj shock, seat top with gray cloth upholstery, lumbar, recline tilt –up & angle adjust armrests. * Trimmed in FabriForm cloth, can be punctured with pens and screwdrivers and will not tear. *Adjustable backrest recline. *Infinitely adjustable mechanical lumbar support *Heavy duty 12 volt air compressor included. *DOUBLE LOCKING SLIDES, fore and aft isolators with lockout. *Ride firmness adjustment *Weight range 110-330 lbs. *** CALL FOR FREIGHT QUOTE *** (Part No: TS5056)
$1437.23

Seat, Industrial - Seat assembly. Durable one-piece stamped steel pan. (Yellow) Leatherette upholstery, Dimensions: 18 inches wide, 19 inches high, 21 inches deep. (Mounting holes 9 inches wide x 9-3/4 inches deep). Fits several Commercial Turf/Mowers, Utility trucks, Fork Lifts, Skid Steer Loaders, Pavers, Sweepers, Construction Equipment, Utility tractors, Row crop tractors, Loader backhoes, Etc. (Part No: TS1110INDY)
$102.91

Seat, Universal - Universal Application Leatherette Suspension seat. For most Compact, Agricultural and Industrial Tractors. Adjustable base for 5 different mounting angles, Internal Suspension Weight Adjustment, Special Slotted Base for mounting holes adjustments of approximately 2-1-2 inches forward/rear, Adjustable Slide Track. IMPORTANT: THESE SEATS FIT MOST TRACTORS, BUT NOT ALL. PLEASE LOOK CLOSELY AT THE DIMENSIONS ON THE PICTURE BEFORE ORDERING TO BE SURE IT WILL FIT YOUR TRACTOR. Color is Black. Additional $30 shipping due to size and weight. IF ORDERING ON-LINE, THIS ADDITIONAL CHARGE WILL BE ADDED TO YOUR ORDER AFTER YOUR RECEIPT IS PRINTED. (Part No: TS1050ATSP)
$89.37

Seat, Universal - BLUE Universal application leatherette suspension seat. For most compact, agricultural and industrial tractors. Adjustable base for 5 different mounting angles, internal suspension weight adjustment, special slotted base for mounting holes adjustments of approximately 2-1-2 inches forward/rear, adjustable slide track. IMPORTANT: THESE SEATS FIT MOST TRACTORS, BUT NOT ALL. PLEASE LOOK CLOSELY AT THE DIMENSIONS ON THE PICTURE BEFORE ORDERING TO BE SURE IT WILL FIT YOUR TRACTOR. Color is BLUE. Add $15 additional shipping per seat due to size and weight. IF ORDERING ON-LINE, THIS ADDITIONAL CHARGE WILL BE ADDED TO YOUR ORDER AFTER YOUR RECEIPT IS PRINTED. (Part No: TS1060ATSP)
$89.37

Seat, Universal - Universal Application Leatherette Suspension seat. For most Compact, Agricultural and Industrial Tractors. Adjustable base for 5 different mounting angles, Internal Suspension Weight Adjustment, Special Slotted Base for mounting holes adjustments of approximately 2-1-2 inches forward/rear, Adjustable Slide Track. IMPORTANT: THESE SEATS FIT MOST TRACTORS, BUT NOT ALL. PLEASE LOOK CLOSELY AT THE DIMENSIONS ON THE PICTURE BEFORE ORDERING TO BE SURE IT WILL FIT YOUR TRACTOR. Color is BLACK. (Part No: TS1075ATSP)
$89.37

Seat, Universal - Seat assembly, black leatherette upholstery, dimensions: 18-3/4 inches wide, 19 inches high, 21 inches deep. Non-suspension type with slide track for forward/rear adjustment (slide track 9 inches wide x 11-1/4 inches deep). Backrest angle adjustment. ***IMPORTANT NOTE: Please verify Seat and slide track dimensions listed above before ordering. Weight 33 pounds. (Part No: TS1110BK)
$111.23

Seat, Universal - Seat assembly, blue leatherette upholstery, dimensions: 18-3/4 inches wide, 19 inches high, 21 inches deep. Non-suspension type with slide track for forward/rear adjustment (slide track 9 inches wide x 11-1/4 inches deep). Backrest angle adjustment. ***IMPORTANT NOTE: Please verify seat and slide track dimensions listed above before ordering. Weight 33 pounds. (Part No: TS1110BL)
$113.74

Seat, Universal - Seat assembly, yellow leatherette upholstery, dimensions: 18-3/4 inches wide, 19 inches high, 21 inches deep. Non-suspension type with slide track for forward/rear adjustment (slide track 9 inches wide x 11-1/4 inches deep). Backrest angle adjustment. ***IMPORTANT NOTE: Please verify seat and slide track dimensions listed above before ordering. Weight 33 pounds. (Part No: TS1110YL)
$110.68

Tie-On Seat Cover - Yellow & Green, 19 inches wide. Deluxe with 2 inches of foam. Fits only tractors that use a PAN type seat. (Part No: R2602)
$37.80

Tie-On Seat Cover - Yellow & White, 21 wide. Deluxe with 2 inches of foam. For tractors that use a PAN SEAT only. (Part No: R1014)
$37.80

Tie-On Seat Cover - Green & White, 21" wide. Deluxe with 2 inches of foam. Fits only tractors that use a PAN type seat. (Part No: R1016)
$36.00

Universal Seat - Black leatherette upholstery. Narrow seat for compact tractors. Internal suspension, weight adjustable. 5 position adjustable base. Special slotted base for mounting. Seat is 15 inches wide, 17 inches long, 19 inches high to the back of the seat. (Part No: TS1015)
$182.49

Universal Seat - **YELLOW** Universal Application Leatherette Suspension seat. For most Compact, Agricultural and Industrial Tractors. Adjustable base for 5 different mounting angles, Internal Suspension Weight Adjustment, Special Slotted Base for mounting holes adjustments of approximately 2-1-2 inches forward/rear, Adjustable Slide Track. IMPORTANT: THESE SEATS FIT MOST TRACTORS, BUT NOT ALL. PLEASE LOOK CLOSELY AT THE DIMENSIONS ON THE PICTURE BEFORE ORDERING TO BE SURE IT WILL FIT YOUR TRACTOR. Color is John Deere Yellow. Add $15.00 additional shipping due to weight. IF ORDERING ON-LINE, THIS ADDITIONAL CHARGE WILL BE ADDED TO YOUR ORDER AFTER YOUR RECEIPT IS PRINTED. (Part No: TS1040ATSP)
$88.39

Sheet Metal / Body Parts
2 Hour DVD - The How To of Sheetmetal Repair - This DVD is intended to show how to restore sheetmetal on your tractor. A John Deere tractor is used in the demonstrations but the information is useful for all tractors. You can use this DVD as a tool to evaluate what work, cost, and time it is going to take to restore the tractor you own or are looking to purchase. 118 minutes. (Part No: RCR06-DVD)
$25.68

Battery Hold Down Bolt - These J-Bolts are 10 3/4 inches long with 5/16 inch 18 UNC thread. There is 2 inches of thread. Verify measurements before ordering. Replaces original part numbers 198185A1, 393161R1. (Part No: 198185A1)
$3.75

Cab Foam Kit Spray Adhesive - 1 16 Oz. can will attach most kits. Large, multi piece kits may need 2 cans. (Part No: R0140)
$31.59

Fender Hand Grip - Used on many ag tractors, combines, implements and industrial tractor applications. (Part No: R20759)
$6.42

Pilot Punch Set - Set contains 12 sizes one of each 1/16, 3/32, 1/8, 5/32, 3/16, 7/32, 1/4, 5/16, 3/8, 7/16 and 1/2. (Part No: RPD112K)
$146.93

SAFETY STEP KIT - Traction Where you need it. Great for use on tractor and combine steps, trailers, grain bin ladders and more. Kit includes 1 pint safety base and safety grit. (Part No: SSK14011)
$53.12

Toolbox - This universal toolbox fits various tractor models. It measures 11 inches long, 4 inches wide, and 4 1/2 inches tall. The mounting holes must be drilled to match your tractor. (Part No: ABC308)
$41.99

Toolbox, Fender Mount - This is an aftermarket toolbox designed to mount easily on the fender of most agricultural and industrial tractors. This is an aftermarket item, unlike any original toolboxes, and is meant for working tractors in need of a good toolbox. 18 inches long, 3-5/8 inches wide and 4-1/2 inches deep. Sheet metal parts may or may not come painted as pictured (unless the description states the color). They often come with only a primer coat of paint. (Part No: TB100FM)
$46.62

Toolbox, Universal - Universal Toolbox Approx. 16 1/4 Inches X 4 3/4 Inches X 5 Inches. This is a Universal Part and Color varies depending on availability. (Part No: R2685)
$31.70

Steering
Eaton Power Steering Pump Replacement - This Power Steering Pump replaces the Eaton style belt driven Power Steering Pump. It also replaces Eaton part numbers: 503-1005-005, 20928 and P761. This is a Redesigned Pump that uses a bearing instead of original bushing. It can also be adapted to tractors using Char-Lynn power Steering with an Eaton Pump. Please note that this pump does not include brackets, top mounted reservoir, or pulley. Some applications will require a new pressure hose to be made for a 5/8-18 inch inverted flare type fitting. The shaft diameter measures .670 inches. The shaft length, where the pulley mounts measures .575 inches. There is a 2 inch thick pump housing where the bracket bolts on. Pressure is preset at 1.32 GPM. (Part No: S03-1003)
$384.33

Filter, Power Steering - Filter case size is 3 inches diameter and 1 1/2 inch height. Center hole is approximately 7/8 inch diameter. VERIFY size before ordering. It is used on tractors with Eaton style power steering pumps. Replaces: PMLF614 (Part No: AE33538A)
$9.30

Power Steering Pump Pulley - This Power Steering Pump Pulley is used with S03-1003 Power Steering Pump. It is designed for Tractors using Eaton Style power steering pump. It is made of Stamped steel. Measures 5 inches outside diameter, 0.675 inch bore, 1/8 inch keyway, 0.9715 inch total width for 1/2 inch belt. (Part No: ABC1417)
$37.95

Steering Wheel Spinner, Bare Aluminum - Comes with mounting hardware. (Part No: R3275)
$7.26

Steering Wheel Spinner, Black - Comes with mounting hardware. (Part No: R3276)
$7.26

Steering Wheel Spinner, Blue - Comes with mounting hardware. (Part No: R3279)
$7.26

Steering Wheel Spinner, Green - Comes with mounting hardware. (Part No: R3278)
$7.20

Steering Wheel Spinner, Orange - Comes with mounting hardware. (Part No: R6323)
$6.69

Steering Wheel Spinner, Red - Comes with mounting hardware. (Part No: R3277)
$7.26

Steering Wheel Spinner, Yellow - Comes with mounting hardware. (Part No: R3280)
$7.20

Tools
Blade Fuse Assortment - With 6-24 volt tester light and fuse puller. Contains 93 pieces. 5, 10, 15, 20, 25 and 30 amp blade type fuses. (Part No: S.29891)
$15.23

Chain Binder - 1/4 inch chain binder, 2600 pound load limit. (Part No: LL104)
$36.73

Chain Binder - 3/8 inch chain binder, 5400 pound load limit. Use with either 5/16 inch or 3/8 inch chain. (Part No: LL105)
$42.63

Chain Binder - 1/2 inch chain binder, 9200 pound load limit. Use with either 3/8 inch or 1/2 inch chain. (Part No: LL106)
$79.85

Chain Binder - 1/2 inch chain binder, 9200 pound load limit. Use with either 3/8 inch or 1/2 inch chain. (Part No: LL106)
$79.85

Combination Wrench Set - This wrench set is 22 pieces and comes with both SAE and Metric measurements. Each wrench is made of polished chrome vanadium steel. They come with a durable plastic rack for handy storage and a LIFE TIME UNLIMITED WARRANTY. The Metric measurements are from: 9 to 19 mm and the SAE measurements are from: 1/4 to 7/8 inch. (Part No: W1069)
$24.76

Combination Wrench Set - This combination wrench set is 11 pieces. Each wrench is made of chrome vanadium steel. This set comes in a handy storage rack and includes a LIFETIME UNCONDITIONAL WARRANTY. The SAE sizes range from 1/4 to 7/8 inch. (Part No: W1061)
$12.60

Compression Tester - This tester checks the cylinder compression up to 300 PSI. It fits 14mm and 18mm spark plug threads and is equipped with an air-hold valve, gauge reset button, 11 inch flexible rubber hose, and a complete list of instructions. (Part No: W80579)
$24.36

Cotter Pin Assortment - This pin assortment contains 150 pieces, all in a convenient re-sealable plastic case. It includes sizes of: 1/8 inch x 2 inches, 5/32 inch x 2 1/2 inches, 3/16 inch x 3 inches, 1/4 inch x 2 inches, 1/4 inch x 3 inches, 5/16 inch x 2 1/2 inches. (Part No: W5206)
$9.36

Cotter Pin Assortment, Small - 560 piece assortment of 1/16 inch x 1 inch, 3/32 inch x 1 inch, 3/32 inch x 1-1/2 inches, 1/8 inch x 1-1/4 inches, 1/8 inch x 2 inches, 5/32 inch x 2-1/2 inches. All in convenient re-sealable plastic case. (Part No: W5205)
$7.05

Diesel Compression Test Kit - This diesel compression kit includes 9 adapters for popular Domestic, Asian, and European vehicles and comes in a protective case. With this kit you can test your compression through the glow plug or the injector holes. The Gauge reads from 0 to 1000 PSI (0-700kPA) and is rated at +/-2 for accuracy. It will fit the following thread sizes: 24 inches x 2 inches, 12 inches x 1 1/4 inches, 10 inches x 1 1/4 inches and 10 inches x 1 inch. (Part No: W89731)
$52.86

Digital Calipers, Stainless - High quality hardened stainless steel digital caliper. Calculates measurements up to 6 inches with SAE and METRIC conversions. Includes convenient carrying case and spare battery. (Part No: CAL6)
$37.53

GREASE GUN - GREASE GUN. Pistol handle grease gun uses standard 11 inch grease cartridge. Develops 8000 lbs pressure. Pistol design makes it convenient to use. (Part No: GG3121)
$29.17

GREASE GUN - Spring fed 11 inch barrel grease gun. Uses standard 11 inch grease cartridge. Lever handle develops 10, 000 lbs of pressure. (Part No: GG1080)
$20.66

GREASE GUN - HEAVY DUTY Grease gun, ultimate gun designed specifically for heavy-duty use and is built to take extreme punishment. (Part No: GG11142)
$36.00

GREASE GUN CLAMP - Clamp holds all 2-1/4 inch diameter barrel hand guns. Bolts or screws anywhere through hole in bracket base. (Part No: GC102)
$11.21

GREASE GUN POWERLUBER 14.4V BATTERY - Battery, Replacement 14.4 Volt NI-CAD rechargeable battery for use with GGPL1442B & GGPL1444B PowerLuber grease gun. (Part No: GGPL1401)
$134.19

GREASE GUN POWERLUBER 14.4V with CASE 1 BAT - Grease gun 14.4 Volt PowerLuber. Professional two-speed cordless rechargeable grease gun. Complete with 110-volt fast charger, 14.4 volt NI-CAD rechargeable battery, 30 inch flex hose with spring guard and custom carrying case to hold two rechargeable batteries. (Part No: GGPL1442B)
$288.95