(800) 853-2651 View Cart
 

• Tractor Parts
• Engine Kits
• Carburetors
• Manuals
• DVDs
• Hats
• Books


• Contact Us
• Shipping Rates
• Return Policy
• Ordering Help
• Company Info
• Parts Warranty
• Forums


Ford 8N Tractor Parts

[ Show Pictures ]

[Categories]   [All Ford Models]   [Print]  


Brakes
Brake Adjusting Hole Cover - For tractor models 8N, NAA, Jubilee, 501, 600, 700, 800, 900, 1801, (2000, 4000 4 cylinder) all from 1948 to 1964. (Part No: H2092)
$7.03

Brake Backing Plate - For 8N, NAA, Jubilee. Brake Backing Plate Restoration Quality, with felt seal. (Part No: 8N2255)
$75.93

Brake Backing Plate Felt Seal - For tractor models 8N, NAA, Jubilee. (Part No: 8N2217)
$3.88

Brake Backing Plate Support - For 8N and NAA. (Part No: 8N2212B)
$79.69

Brake Camshaft Hole Cover Spring - Tractors: 8N, Jubilee, NAA, 600, 601, 700, 701, 800, 801, 900, 901, 2000, 4000 (1948-1964). (Part No: 8N2322)
$4.96

Brake Cover - Cover, Brake camshaft hole. This is an EXACT reproduction of the ORIGINAL brake cover. For tractors: 8N, NAA (1948 TO 1954). (Part No: 8N2224)
$6.56

Brake Cross Shaft Bushing - Measures 1 inch long, 1 inch inside diameter and .010 thick. Press into transmission housing {one on each side}. Sold each. For tractors: 9N, 2N, EARLY 8N {1939-1949}. (Part No: 782477)
$10.30

Brake Cross Shaft Bushing - Measures about 1 inch I.D., 1 1/6 O.D. and 1/2 inch wide. Bushing is a little less than 1/16 thick. Presses into transmission housing. For tractors: LATE 8N, NAA, Jubilee {1949-1954}. (Part No: C0NN2477)
$10.30

Brake Drum - For tractor models 8N, NAA, Jubilee. An additional $10.00 will be added to shipping per drum (heavy item). IF ORDERING ON-LINE, THIS ADDITIONAL CHARGE WILL BE ADDED TO YOUR ORDER AFTER YOUR RECEIPT IS PRINTED. (Part No: 8N1126)
$108.94

Brake Drum Repair Kit - For tractor models 8N, NAA Jubilee. Replaces: 8N2027B Contains: Anchor (2), H2041 Adjuster Screw, 8N2217 Felt Backing Plate Seal, 8N2048 Adjuster Socket, 8N2223 Adjuster Nut, 8N2049 Adjuster Spring, 8N2297B Return Spring, 8N2299 Secondary Spring LH only. Brake Hardware Kit for 1 wheel. (Part No: 8NAA2250)
$29.82

Brake Shoe Return Spring, RH Brake - For tractor models 8N, NAA, 501, 600, 700, 800, 900, 2000, 4000 series (1948 to 1964). ** Sold in quantities of 2, priced individually. Must order in quantities of 2. (Part No: NCA2204A)
$5.42

Brake Shoes - Complete set of 4. For 8N, NAA, Jubilee. (Part No: 8N2200B)
$45.54

Clutch
Clutch Alignment Tool - 1-3/8" 10 spline, .67" pilot. For tractor models with single clutch: 8N, 9N, 2N, NAA, Jubilee, 600, 620, 630, 640, 650, 660, 700, 740, 750, 800, 820, 840, 900, 950, 960. (Part No: 1112-5996)
$6.38

Clutch Disc - 9" Clutch Disc, Hub-1 3/8 inch, Splines-10, 6 springs. Fits 8N, 9N, 2N, NAA (4 speed), NAB, Jubilee, 600, 620, 630, 640, 650, 660, 700, 800, 900 (to serial # 14257), 1800, 2130. Improved from original by added springs. Also replaces 84365150, 91A7550, NAA7550A. (Part No: 91A7550WHD)
$27.75

Clutch Kit, 9 Inch, Single Clutch - This 9 inch clutch kit contains Kit contains 9" 10 spline spring drive disc NAA7550A, 9" single pressure plate 8N7563, pilot bearing C5NN7600A and release bearing C0NN7580A, includes pilot tool. Alignment tool 1112-5996. Fits 1800 SERIES, 1801, 1821, 1841, 2000 (4 CYL 62-64), 2031, 2110TR, 2120, 2130, 2131, 2N, 4000 (4 CYL 62-64), 4031, 4110TR, 4120, 4121, 4130, 4131, 4140, 501 SERIES, 541, 600, 601, 620, 621, 630, 631, 640, 641, 650, 651, 700, 701 SERIES, 740, 741, 800, 801, 820, 821, 840, 841, 850, 851, 8N, 900, 901, 941, 950, 951, 9N, NAA, NAB. (Part No: 8N7563K)
$82.73

Clutch Pedal Arm Bushing - For tractor models 8N, Jubilee, NAA, (1948-1954). This bushing is 1.002" I.D. x 1-1/2" long. Minimum Order Qty is 2. (Part No: 8N7508B)
$7.41

Clutch Release Arm Kit - For 8N, NAA, Jubilee, 600, 700, 800, 900 (up to 1958). Clutch Release Arm Kit contains: eyebolt #355584S8, pin #8N7533, and clutch release arm #8N7511B. (Part No: S.66657)
$50.33

Clutch Shaft Bushing - 7/8 Inch inside diameter. For tractor models 8N, 9N, 2N, NAA, Jubilee, 600, 700, 800, 900, 601, 701, 801, 901, 2000, 4000. (3 or 4 Speed Trans Only). Min order qty is 2. (Part No: 407508A)
$6.15

Pilot Bearing - For tractor models 8N, 9N, 2N, NAA, NAB, Jubilee, 600, 700, 800, 900, 601, 701, 801, 901, 2000, 4000, Dexta, Super Dexta, Major, Power Major, Super Major. (Part No: C5NN7600A)
$1.97

Pressure Plate - 9" single, flat flywheel. For tractor models 1800, 2130, 8N, 9N, 2N, NAA, NAB, Jubilee, 600, 700, 800, 900 with single clutch. (Part No: 8N7563)
$67.55

Release Bearing - For Ford Tractors with 9" and 10" Single Clutch 1939-1964. 2.0625 Inch inside diameter. (Part No: 78-7580A)
$15.52

Release Bearing Hub - For tractor models 1801, 1821, 1841, 2000, 2030, 2031, 2111, 2120, 2130, 2131, 2N, 4000, 4030, 4031, 4040, 4120, 4121, 4130, 4131, 4140, 501, 541, 600, 601, 620, 621, 630, 631, 640, 641, 650, 651, 700, 701, 740, 741, 800, 801, 820, 821, 840, 841, 850, 851, 8N, 900, 901, 950, 951, 9N, NAA, Jubilee, NAB. (Part No: 9N7561)
$29.41

Release Bearing Spring - This Release Bearing Spring measures .627" Outside Diameter, 4.875" overall length and .095" wire diameter. For tractor models 8N, 9N, 2N, NAA, Jubilee, 501, 541, 600, 601, 620, 621, 630, 631, 640, 641, 700, 701, 740, 741, 800, 801, 820, 821, 840, 841, 900, 901, 940, 941, 1801, 1821, 1841, (2000, 4000 4-cyl), 2030, 2031, 2110, 2111, 2130, 2131, 4030, 4040, 4031, 4110, 4121, 4130, 4131, 4140. Two are used per tractor. Sold and priced each. (Part No: 9N7562)
$5.89

Cooling System
Cooling System Kit, Early - Complete cooling system overhaul for 9N, 2N and Early 8N SN# 263842 and below. Includes Radiator, Radiator Cap, Radiator Hood Pad, Upper and Lower Radiator Hose, 4 hose clamps, Radiator Mounting Pads, Thermostat and Water Pump. (Part No: CSK-E)
$290.03

Cooling System Kit, Late - Complete cooling system overhaul for Late 8N SN# 263842 and up. Includes Radiator, Radiator Cap, Radiator Hood Pad, Upper and Lower Radiator Hose, 4 hose clamps, Radiator Mounting Pads, Thermostat and Water Pump. (Part No: CSK-L)
$287.39

Fan Belt - For tractor models 8N, 9N, 2N EARLY with front mount distributor. Length is 44 1/8 inches. Alternator belt for those tractors using our 12 volt conversion kit. (Part No: 9N8620B3-SL)
$13.47

Fan Belt - Belt is 41 3/8 inches long. For tractor models 8N late (with side mount distributor), NAA (1952-1954, Jubilee. This belt also works with # 8NL10300ALT Alternator conversion kit.) (Part No: 8N8620)
$5.29

Fan Belt - For tractor models 8N, 9N, 2N prior to SN# 263844 using generator and have front Mount distributor. Not for tractors with alternator conversion. This belt is 46-1/8" long. (Part No: 9N8620B3)
$11.91

Fan Blade - 4 Blade - For tractor models 9N, 8N, NAA, Jubilee. Has 4 mounting holes on 3.125" Centers. Diameter is 15.75". (Part No: 8N8600A)
$37.47

Fan Blade, 6 Blade - For 9N, 8N, 2N, NAA, Jubilee. 6 Blade Fan for extra cooling in those hotter climates. (Part No: 9N8600D)
$114.62

Fan Shroud - For 8N, 9N, 2N. Metal Fan Shroud. (Part No: 2N8146)
$59.35

Radiator - Restoration Quality. This radiator is made like the original with a curved top tank (less cap), 4 rows of tubes. Copper core. For 8N, 9N, 2N. Draincock included. Meets or exceeds original manufacturers specification for cooling. 1 year warranty. This is a replacement radiator for OEM part number 8N8005. (Part No: 8N8005-R)
$260.82

Radiator - This is a Replacement High Quality Radiator. It is not exactly like original but will replace the original with no modification required (except if using a fan shroud). For 8N, 9N, 2N. Copper Core, 3 rows of tubes, weight 16 lbs. Drain cock included. 1 year warranty. (less cap). The Original or Replacement Fan Shroud will not fit this radiator without some modification to the fan shroud. This modification consists of trimming the inside of the bottom of the fan shroud. This is a replacement radiator for OEM part number 8N8005. (Part No: 8N8005)
$172.50

Radiator Cap - Plain, conventional type 4 psi pressure cap, less ornament. For tractors 8N, 9N, 2N. (Part No: 2N8100A-LW)
$8.58

Radiator Cap, Black - For 8N, 9N, 2N with pressurized system. Winged Radiator Cap. (Part No: 2N8100A)
$7.15

Radiator Cap, Chrome - For tractor models 8N, 9N, 2N with pressurized system. Winged Radiator Cap, Chrome. (Part No: S.61615)
$11.83

Radiator Drain Tap - Drain Tap-For 8N, 9N, 2N, NAA, Jubilee, 600, 700, 800, 900, 601, 701, 801, 901, 2000, 4000. This is also the same tap for the engine block in the 8N, 9N, 2N, NAA engines. (Part No: C9NN8115A)
$2.58

Radiator Hood Pad - These Radiator Hood Pads fit models 8N, 9N, 2N. One pad is used at the top of the radiator. (Part No: 2N8032)
$2.38

Radiator Hose Clamp, Upper & Lower - EXACT reproduction of the ORIGINAL hose clamp. For tractor models 8N, 9N, 2N (1939-1954), NAA, Jubilee (2 per tractor, 1953-1954). For 1 7/8 O.D. hoses +/- 1/8. SHOWN IN PAIR, PRICED EACH. (Part No: 608287)
$4.80

Radiator Hose Set - 8N SN# 263844 and above. Lower Radiator Hose #8N8286 and Upper Radiator Hose #2N8260. (Part No: 8NL-HOSESET)
$12.84

Radiator Hose Set - 8N, 9N, 2N SN# 263842 and below. Upper Radiator Hose #2N8260 and Lower #312588. (Part No: EARLY-HOSESET)
$11.76

Radiator Hose, Lower - Hose, water pump to radiator lower. Hose is 1 1/2 inch inside diameter. For tractor models 2000, 2N, 4000, 501, 600, 601, 700, 701, 800, 801, Early 8N, 900, 901, 9N, NAA. (Part No: 312588)
$6.98

Radiator Hose, Lower - Hose, radiator to outlet lower. For model Late 8N. (Part No: 8N8286)
$6.54

Radiator Hose, Upper - Hose, cylinder head to radiator upper. For tractors 9N, 2N & 8N (Part No: 2N8260)
$6.47

Radiator Mounting Bolt Kit - These Radiator Mounting bolts are used on aftermarket radiators to mount the radiator to the front support. Kit includes 2 carriage bolts, 2 nuts, 2 lock washers and 2 washers. For tractor models: 2000 4 cylinder, 2N, 4000 4 Cylinder, 8N, 9N, Golden Jubilee, Jubilee, NAA, NAB, 600, 601, 611, 620, 621, 630, 631, 640, 641, 650, 651, 660, 661, 671, 681, 800, 801, 811, 820, 821, 840, 841, 850, 851, 860, 861, 871, 881, 2030, 2031, 2120, 2130, 2131, 4030, 4031, 4120, 4121, 4130, 4131 4 cylinder. Replaces nut 34670, 34090S, Flat Washer 44732, Lock Washer 34808, Carriage Bolt 351655S8. (Part No: 351641S8)
$3.91

Radiator Mounting Pads - These Radiator Mounting Pads are sold in a package of 2. Price is for a package of 2 pieces. For tractor models 8N, 9N, 2N, NAA, Jubilee, 600, 700, 800, 900, 601, 701, 801, 901, 2000, 3000, 4000, 5000, 7000, 2600, 3600, 4600, 5600, 6600, 7600, 6700, 7700, 2310, 2610, 3610, 3910, 4610, 5610, 6610, 7610, 6710, 7710, 7810, 8010. Replaces B9NN8125A, 81811605 and C5NN8125A. Two are used per tractor on the bottom of the radiator. (Part No: 180705M1)
$6.32

Thermostat - This thermostat is 160 degree lo-temperature. For tractors models 8N, 9N, 2N. Fits in upper radiator hose with the pointed end towards the front of the tractor. Thermostat is 2.250 inches long. (Part No: B2NN8575A)
$16.50

Water Pump - For tractor models 8N, 9N, 2N. Comes with Pulley, Rear Cover Plate and Gasket. Pulley will accommodate a 1/2 or 5/8 belt. (Part No: CDPN8501A)
$38.25

Water Pump Cover plate Gasket - Tractors: 8N, 9N, 2N (Part No: 9N8507)
$1.59

Water Pump Kit - Repair kit. For 8N, 9N, 2N, NAA, Jubilee (Part No: CPN8591B)
$51.05

Water Pump Mounting Gasket - Gasket, pump rear to cyl. block. Tractors: 8N, 9N, 2N (Part No: 9N8513)
$2.08

Water Pump Sealant - RTV Blue 3.35 oz. tube. (Part No: PRM77BR)
$5.99

Decals and Emblems
Decal , Fender Set - For 8N, 9N, 2N. Each decal is approximately 8-3/4" wide by 3-1/4" tall. Fender Decals (2) Red Ford Script. (Part No: R2006)
$18.38

Decal Set - Combination Decal Set For tractor models 8N, 9N & 2N (1939-1952). Set of 10 self adhesvie decals. Contains Decals for Air Cleaner, Oil Filter, Position Control, PTO Warning, Hood Sides (Red Ford Name 2-1/4" x 5-1/4"), Fenders (Red Ford name 3-1/4" x 9")and Tachometer. (Part No: R2008)
$26.50

Decal Set - For 8N, 9N, 2N, all 1939-1947. Decal set for the Air Cleaner, Oil Filter Position (2) and PTO Warning. (Part No: FO1)
$8.56

Decals, Hood Set - For tractor models 8N, 9N, 2N, 1947-1952. Hood Decals (2) Red Ford Script. (Part No: R2005)
$14.98

Ford Script Painting Mask - Includes 1 small 5-3/8" x 2-1/4", and 1 large 8-5/8" x 3" painting masks. For model 8N. Application directions included. Note: the picture is to demonstrate what your finished result will look like it is not a picture of the mask itself. (Part No: S.61441)
$20.77

Hood Emblem - 8N (bright metal with red enamel background). (Part No: 8N16600A)
$37.15

Hood Emblem - 8N One piece emblem. Cast aluminum, dull finish with red outline and lettering. (Part No: 8N16600B)
$17.45

Plate - Patent data plate, with drive screws to install. For tractors: 8N, {1948-1952}. (Part No: 8N14001)
$11.07

Drive Train
Axle - Rear Axle 8N, NAA, Jubilee. Total length is 32.25 inches. **$15 ADDED TO SHIPPING DUE TO WEIGHT** IF ORDERING ON-LINE, THIS ADDITIONAL CHARGE WILL BE ADDED TO YOUR ORDER AFTER YOUR RECEIPT IS PRINTED. (Part No: 8N4235C)
$158.18

Axle Bearing Assembly - For tractor models 8N, 9N, 2N, NAA, Jubilee. This includes rear axle bearing(2N4221) and cup(9N4222). (Part No: S.18516)
$40.42

Axle Kit - Kit contains, 2 shaft bearings, 2 housing gaskets, 2 shaft collars, 2 bearing cups, 2 inner axle seals, 2 outer axle seal assemblies, 2 rear axle nut lock rings Not Links. For tractor models 9N, 2N and 8N up to Serial Number 486, 753. Kit comes with 2 sets of outer axle seals one for use on 9N, 2N tractors and one for 8N. (Part No: AXLEKIT-8NEARLY)
$197.90

Axle Kit, Late - Kit contains, 2 rear axle shaft bearings, 2 inner seals, 2 washers, 2 housing gaskets, 2 shaft bearing cups, 2 inner oil seals, 1 pr outer oil seal assemblies, 2 nut & lock rings, 2 shaft gaskets. For model 8N after Serial Number 486753. (Part No: AXLEKIT-8N)
$190.17

Axle Nut - 1.25", 18 hex. For tractor models (8N 1948-1953), (NAA, Jubilee 1953-1955), NAB. (Part No: 8N4179)
$7.53

Axle Nut & Snap Ring - Kit, nut & snap ring. For tractor models 8N, NAA. (Part No: CBPN4179A)
$8.39

Axle Nut Lock Ring - For 8N 1948-1953, Jubilee & NAA. Snap Ring. Minimum order quantity is 10. Sold In Lots Of 10, priced each. (Part No: 8N4187)
$2.05

Axle Nut, Clamp Lock Type - Clamp lock nut, rear axle, 1-1/4". For 8N, NAA, Jubilee. This improved nut helps to prevent premature wear on both axle and hub. (The ring on the original type can fall out or rust out which allows the nut to come loose). This nut stays tight! Replaces CBPN-4179-A and 8N4187. (Part No: LN10-21)
$39.80

Axle Oil Seal Gasket, Inner - For 8N 1948-1950. Used between A8NN4251A Seal & Retainer in Oil seal assembly. Price is for each. (Part No: 8N4290)
$0.77

Axle Oil Seal-Outer - For tractor models 8N to SN# 486753. Inside Diameter 2 3/4 inch. Rear axle oil seals. Also comes as part of A8NN4248A Assembly. Packaged in qty of 2, price is for a pair. (Part No: A8NN4251A)
$9.75

Axle Outer Retainer - For model 8N to SN# number 486753. Rear Axle Outer Retainer. These retainers come with seals and gaskets. Order Qty of 1 for a set of 2. (Part No: A8NN4248A)
$28.31

Axle Outer Retainer Gasket - Requires 2. For tractor models 8N 1948-1950. (Part No: 8N4225)
$1.89

Axle Seal, Inner Pair - Seal, Oil For 8N, Jubilee, NAA. Enter QTY 1 For PKG of 2. (Part No: 8N4233A)
$9.99

Axle Seal, Outer Pair - For tractor models 8N SN# 486753 UP, NAA, Jubilee. Comes in pairs. 3-3/4" O.D., 2-7/8" I.D. (Part No: D5NN4115A)
$14.26

Axle Shaft Bearing - Rear Axle Shaft Bearing, Tapered Cone. (Part No: 2N4221)
$47.65

Axle Shaft Gasket - For tractor models 600, 700, 800, 900, 8N, NAA, Jubilee. I.D. 2 inch, O.D. 2 1/4 inch. (Part No: 8N4284)
$2.80

Axle Washer - For model 8N. (price shown is for EACH, minimum Qty is 2. (Enter 2 in QTY box.) (Part No: 8N4293)
$5.22

Countershaft - Fits 8N. The overall length of this countershaft is 11.887". Replaces 8N7111 (Part No: 8N7111)
$122.13

Differential Gasket Kit, 6 Pieces - Fits 8N, 9N, 2N. 6 Piece Set. Includes: (1) 9N502, (1) 9N611, (2) 2N4035, (1) C5NN747A, (1) 9N4662, (1) 181217M3 (Part No: DGK928)
$9.45

Differential Pinion Bearing Cone - For tractor models 2000 1965>, 2N 1939-52, 3000 1965>, 4110 1965>, 600 with 4 SP. TRANS. SN<54165 - 1958, 5 SP. SN<196155 - 1959, 601 with 4 SP. TRANS. SN54166> -1958-62, 5 SP. SN106116> - 1960-64, 8N 1939-52, 9N 1939-52, Dexta 1957-1964, NAA 1953-54. (Part No: BB4221B)
$17.07

Differential Pinion Bearing Cup - Bearing cup, differential bearing For 2000, 2120, 2N, 3000, 4110, 600, 601, 8N, 9N, Dexta, Jubilee, NAA (Part No: BB4222)
$14.89

Differential Pinion Bearing Cup, Front - For tractor models 2N 1939-52, 8N 1939-52, 9N 1939-52, Dexta 1957-4/1962, NAA, Jubilee 1953-54. (Part No: BB4616B)
$41.83

Differential Pinion Cone, Front - Bearing, Tapered Cone. For tractor models 2N 1939-1952, 8N 1939-1952, 9N 1939-1952, Dexta 1957-4/1962, NAA, Jubilee 1953-1954. (Part No: BB4621B)
$66.79

Gasket, Main Drive Gear Bearing Retainer - For tractor models 8N, 9N, 2N, NAA, Jubilee, NAB. SOLD IN QUANTITIES OF 5, PRICE IS FOR 1. (Part No: 9N7086)
$1.22

Gasket, Paper Shim, For Bearing Retainer - Fits Ford 8N, 9N, 2N, NAA & Jubilee, Replaces #9N4130 & #8N4229 Note: (Use for seal between bearing retainer and axle housing or backing plate. Use in multiples to replace shims #8N4229. Thickness 0.016" Price is for each. (Part No: 9N4130)
$.63

Gasket, Rear axle housing gasket - Gasket center housing to rear axle housing. Tractors: 8N, 9N, 2N. (Part No: 2N4035)
$2.41

Gear Shift Lever Spring - Fits the tractors with 3 or 4 speed transmission or 4 speed torque converter transmission, 2.210 tall, 1.768 tapers to 1.003 O.D., 0.140 wire diameter. For tractor models 8N, 9N, 2N. (Part No: 9N7227B)
$9.85

Gear Shift Lever, with Knob, 4-Speed Transmission - Replaces NAA7209A and 8N7209C shift levers. This newer version has 5/16" UNF thread for the shift knob (knob included) The early series 3/8 shaft is no longer available. Note: uses gear shift knob BB7213A. Fits 8N, NAA, Jubilee, 600, 700, 800, 900, 620, 621, 630, 631, 640, 641, 740, 741, 840, 841. (Part No: C5NN7202B)
$72.62

Gear Shift Pin - Fits 8N, 9N, 2N, NAA, Jubilee, 600, 700, 800, 900, 601, 701, 801, 901, 2000, 4000(>1965 (with 3 & 4 Speed transmission). (Part No: 9N7221B)
$3.96

Gear, 1st, 4 Speed Transmission - 60/28 tooth. For tractor models 2000, 2100, 2110, 2120, 2130, 2150, 2300, 2310, 3000, 3055, 3100, 3110, 3120, 3150, 3190, 3300, 3310, 3330, 3400, 3500, 3550, 4000, 4031, 4040, 4120, 4121, 4130, 4131, 4140, 501, 600, 601, 700, 701, 800, 801, 8N, NAA, NAB, Jubilee. (Part No: 8N7100)
$234.14

Gear, 2nd Transmission Countershaft - Transmission countershaft second gear. For NAA, Jubilee. All 4-speed Ford transmissions (1953-64), 8N (1948-52). 17 teeth. (Part No: B9NN7114A)
$78.20

Gear, 3rd, 4 Speed Transmission - 52 tooth. For tractor models 2000, 2030, 2031, 2100, 2110, 2111, 2120, 2130, 2131, 2150, 2300, 2310, 3000, 3055, 3100, 3110, 3120, 3150, 3190, 3300, 3310, 3330, 3400, 3500, 4000, 4030, 4031, 4040, 4120, 4130, 4131, 4140, 501, 541, 600, 601, 620, 621, 630, 631, 640, 641, 700, 701, 740, 741, 800, 801, 840, 841, 8N, NAA, NAB. All with 4 speed transmissions. (Part No: 8N7102)
$211.66

Gear, 4th, 4 Speed Transmission - Has 28 & 36 teeth. For tractor models 1801, 2000, 2030, 2100, 2110, 2120, 2130, 2150, 2300, 2310, 3000, 3055, 3100, 3110, 3120, 3150, 3190, 3300, 3310, 3330, 3400, 3500, 3550, 4000, 4030, 4031, 4040, 4120, 4121, 4130, 4131, 4140, 501, 600, 601, 700, 701, 800, 801, 8N, NAA, NAB, Jubilee. (Part No: 8N7112)
$190.08

Gear, Mainshaft 2nd - Transmission mainshaft 2nd gear. 56 teeth. For NAA, Jubilee, all 4-speed Ford transmissions (1955-64), 8N, 4-speed transmission, 1948-52. (Part No: B9NN7A381B)
$113.38

Gears, 2nd Mainshaft & Countershaft, 4 Speed Transmission - For 8N, NAA, Jubilee, 600, 800, 900, 2000, 4000 with 4 cyl engines & 4 speed transmissions. Replaces B9NN7A381B and B9NN7114A. (R0625) (Part No: B9NN7A381B-set)
$170.18

Hub - Rear Axle Hub 8N, NAA, Jubilee. With Studs. (Part No: 8N1171)
$62.03

Main Shaft Connecting Coupling - For tractor models 2000, 3000, 8N, NAA, Jubilee all with 4 Speed Transmission. Main Shaft Connecting Coupling has 21 teeth, 16 spline. (Part No: E6NN7106AA)
$61.96

Oil Seal, Main Drive Gear - Oil Seal For 3 & 4 Speed transmission Main Drive Gear on: 8N, 9N, 2N, 600, 700, 800, 900, NAA, NAB, Jubilee. Replaces part number 8N7052A. **Minimum order qty is 2** (Part No: 8N7052A)
$6.10

Rear Axle Bearing Race - Tapered Bearing Cup For 4120, 600, 800, 8N, 9N, 2N, Jubilee, NAA. (Part No: 9N4222)
$8.13

Shift Cover Plate Gasket - For 4-SPEED transmissions. For tractor models 8N, NAA, Jubilee, 501, 600, 620, 630, 640, 650, 660, 700, 740, 750, 800, 820, 840, 900, 950, 960, 2000, 4000 (1948-1964), 2000, 3000 (1965-1970). Sold in lots of 5, priced each. (Part No: 8N7223)
$2.25

Shift Knob - Knob, transmission gear-shift lever. For all 4- & 5- speed transmission models (1950-1964 SN# 252844 & up). (Part No: BB7213A)
$2.98

Shifter Boot - Transmission gear shift lever boot. For tractors: 8N, 9N, 2N, NAA. Bottom hole is 1-1/2" diameter. (Part No: 8N7277)
$9.48

Shifter Boot - Bottom hole is 7/8" dia. For 9N, 2N, 600, 700, 800, 900, 601, 701, 801, 901, 2000, 4000 (ALL 1939 TO 1964 WITH 4 SPEED). Gearshift Boot - Restoration Quality. Can be use to replace 9N7277. (Part No: C5NN7277C)
$2.10

Side Cover Gasket - This side cover gasket fits the following tractor models as a side cover gasket and a PTO shifter cover gasket: 2000, 2N, 4000, 600, 601, 700, 701, 800, 801, 8N, 900, 901, 9N, Jubilee, and NAA. Price is for each. Replaces part number 9N4131. (Part No: 9N4131)
$0.51

Transmission Bearing - Main Pilot Shaft Bearing Cone for 3 & 4 Speed Transmissions. For tractor models 1801, 1821, 1841, 2000, 2030, 2031, 2100, 2110, 2111, 2120, 2130, 2131, 2150, 2300, 2310, 2N, 3000, 3055, 3100, 3110, 3120, 3150, 3190, 3300, 3310, 3330, 3400, 3500, 3550, 4000, 4030, 4031, 4040, 4110, 4120, 4121, 4130, 4131, 4140, 600, 601, 620, 621, 630, 631, 640, 641, 700, 701, 740, 741, 800, 801, 840, 841, 8N, 9N, NAA, Jubilee, NAB. (Part No: 9N7120)
$52.43

Transmission Bearing Cone - Main drive shaft & countershaft bearing cone for 3 & 4 speed transmissions. For tractor models 2000, 2N, 3000, 4000, 5000, 600, 700, 800, 8N, 900, 9N, NAA, NAB. (Part No: 9N7066)
$8.69

Transmission Bearing Cup - Main drive shaft & countershaft bearing cup for 3 & 4 speed transmissions. For tractor models 2000, 2N, 3000, 4000, 5000, 600, 700, 800, 8N, 900, 9N, NAA, NAB. (Part No: 9N7067)
$12.29

Transmission Case to Center Housing Gasket - For tractor models 9N, 8N, 2N. (Part No: 9N4662)
$2.68

Transmission Drain Plug - Has 2.5" outside diameter. For tractors: 8N, 9N, 2N, NAA, {1939-1954}. Also filler plug for tractor:NAA {1953-1954}. Gasket available, order part number 8N7011. (Part No: 9N7010)
$4.67

Transmission Rebuild Kit - For tractor models 9N, 2N and 8N with 3 & 4 speed transmissions (1939-52). This transmission bearing and seal kit contains seals, bearings and gaskets required for transmission rebuild. Contains 2x 9N7086, 1x 9N4662, 1x D5NN7223A, 1x 9N7223B, 1x 8N7052A, 1x15385-TIM, 4x 25877, 4x 25820-TIM. (Part No: TSBK3952)
$115.38

Electrical System
12 Volt Conversion Kit, Front Mount Distributor - 8N, 9N, 2N - Updates older 6-volt tractors to 12-volt charging system. For early 8N, 9N, 2N 1948-1951 with front mount distributor (distributor is right behind radiator), to SN# 263843. Kit includes rebuilt unicharge alternator with pulley and self exciting regulator, 12 Volt coil, wiring harness, top alternator bracket, alternator base bracket, alternator adjusting arm, belt, and instructions. Will not work if you have a magneto. (Part No: 8NE10300ALT-C)
$102.05

12 Volt Conversion Kit, Side Mount Distributor - For Late 8N Tractors with side mount distributors(mounted at an angle near front of engine). Updates older 6-volt tractors to 12-volt charging system. Kit includes: Unicharge alternator w-pulley, Electrical resistor, (Resistor is used if you use your 6 volt coil - OR you can install a 12 volt coil (No coils included) and NOT use this resistor) wiring harness, top alternator bracket, base alternator bracket, alternator adjusting arm, Misc Bolts/Nuts/Instructions. (Part No: 8NL10300ALT)
$85.91

Alternator Adjustable Arm - Alternator adjusting arm. For 8N, 9N, 2N - EARLY with front mount distributor. (Part No: 8NE10304)
$8.93

Alternator Adjustable Arm - Alternator adjusting arm. For 8N Late with Side Mount Distributor. (Part No: 8NL10304)
$6.75

Alternator Base Bracket - Alternator Base Bracket. For 8N, 9N, 2N - EARLY with front mount distributor. (Part No: 8NE10303)
$10.43

Alternator Base Bracket - Base alternator bracket. For 8N Late using side mount distributors. (Part No: 8NL10303)
$33.75

Alternator Base Bracket Kit - Universal - Universal base bracket mounting kit. For converting from a generator to an alternator . Contains: brackets, bolts, washers, nuts & Basic Instructions. Can be used with our 8NE10305SE Alternator. (Part No: 2348258)
$34.20

Alternator Pulley - For 8N, 9N, 2N, NAA, 600, 700, 800, 900, all using 12 Volt conversion kits with a Delco single wire alternator. Pullery, single groove 5/8" wide. The diameter varies from our different suppliers. This measures about 2 5/8 outside diameter, give or take about a 1/4 inch. This should be fine and within the adjustability of the Alternator adjusting arm. (Part No: 98NAA5825)
$9.59

Alternator Top Bracket - Alternator Top Mounting Bracket. For 8N, 9N, 2N - EARLY with front mount distributor. (Part No: 8NE10302)
$15.11

Alternator Top Bracket - Top alternator bracket. For 8N late with side mount distributor. (Part No: 8NL10302)
$11.93

Battery Cable - For 8N, 9N, 2N. Ground Strap. 5.5 inches center to center. (Part No: D1NN14301H)
$9.13

Battery Cable - For 8N 1948-52, Jubilee, (NAA, 600, 620, 630, 640, 650, 660, 700, 740, 750, 800, 820, 840, 900, 950, 960, all 1953 and later. Ground Strap. 6 volt, 11" long. (Part No: FAE14301B)
$11.32

Battery Cable Cover - Rubber cover, battery cable to starter solenoid. For tractors: 8N, Jubilee, NAA {1948-1953}. Replaces: 81826317, 86H14321A, C0NN14321A, C7NN14321A, S115407 (Part No: 86H14321A)
$11.25

Battery Hold Down Bolts - Battery Hold Down Bolts with nuts for 9N, 8N, 2N. One NCA10728WN and one 8N10728WN. Sheet metal parts may or may not come painted as pictured (unless the description states the color). They often come with only a primer coat of paint. (Part No: NCA10718A-BOLTS)
$13.00

Battery Hold Down Kit - This battery hold down kit is for tractor models 8N, 9N, 2N, NAA, 501, 600, 601, 700, 701, 800, 801, 900, 901, 2000-4000 series (1953-1964). Dimensions of hold down, Width 9-1/4", length 7-1/4", center-to-center mounting holes 10-1/8". The short bolt included with this kit is not used on the 8N, 9N, 2N, NAA. A simple bolt is used but not supplied with this kit. (Part No: NCA10718A-KIT)
$32.09

Battery to Starter Cable - For model 8N, 1939-1952. Starter to Battery Cable. 10.5" Long, 1Gauge, 7/16 Diameter. (Part No: 8N14300B)
$12.13

Bearing, Generator Front - BEARING, BALL Bearing, Generator, Front End. For 3 Brush Generator. For 8N, 9N, 2N (Part No: E27N10094B)
$4.88

Clip - Clip for 7/16" hole. Electric wiring to instrument panel support bracket 1948-1952 1 required, Main wiring assembly to instrument panel brace 1 required, Wiring to hood top reinforcement 1950-1952 3 required. For model 8N (1948-1952). (Part No: 51C14197)
$4.13

Clip - Clip for 17/32" hole. Electrical wiring to instrument panel brace 1 required. For model 8N. (Part No: 8N14197)
$5.12

Coil - Six Volt - For tractor models 8N (1939-1950), 9N, 2N with Front Mount Distributor (Part No: 9N12024)
$13.88

Coil, 12-Volt - For 8N, 9N, 2N (SN# up to 263843. Front Mount Distributor 12 Volts (replaces 9N12024-12V) (Part No: 12VOLTCOIL)
$14.63

Coil, High Performance (Black), 12 Volt, Oil Filled - Pertronix Flame Thrower heavy duty, high performance coil is for all 12-volt systems. Delivers up to 40, 000 volts. Oil filled for better cooling and voltage insulation. Enables larger plug gap for greater fuel efficiency and more power. Fits existing brackets. (Part No: 40511)
$35.82

Coil, High Performance (Black), 6 Volt, Oil Filled - Pertronix Flame Thrower high performance coil is for all 6-volt systems. Delivers up to 40, 000 volts. Oil filled for better cooling and voltage insulation. Enables larger plug gap for greater fuel efficiency and more power. (Not for 9N, 2N early 8N using front mount distributors) (Part No: 40011)
$35.82

Condenser - Fits 8N, 9N, 2N with front mount distributor. (Part No: A0NN12300A)
$2.16

Condenser - For NAA, NAB, Jubilee, 8N with side mount distributor only, and 134 & 172 gas engines used on: 501, 541, 600, 601, 611, 620, 621, 630, 631, 640, 641, 650, 651, 660, 661, 671, 681, 700, 701, 740, 741, 771, 800, 801, 811, 820, 821, 840, 841, 850, 851, 860, 861, 871, 881, 900, 901, 941, 950, 951, 960, 961, 971, 981), (2000, 4000 ALL <1964). (Part No: FET12300A)
$2.08

Distributor - For 8N serial #263844 and up - side mount. Can use the Pertronix Electronic Conversion Kit #1244A if 12 volt neg ground, or 1244AP6 if 6 volt pos ground. (Part No: 8N12127B-WCR)
$165.60

Distributor Assembly, Complete - For 9N, 2N, (8N all front mount SN# up to 263843). Includes: Points, condenser & Distributor Cap. Does not include coil or mounting gaskets. (Part No: 9N12100)
$182.12

Distributor Base Assembly - Front mount distributor base assembly, with clamps & rear bushing. For tractor models 8N, 9N, 2N. Does not come with breaker plate. (Part No: 9N12139)
$150.61

Distributor Breaker Plate Retainer Clip - For tractor models 8N, 9N, 2N (Front Mounted Distributor). (Part No: 91A12146)
$2.10

Distributor Bushing, FRONT - Front bushing is for FRONT MOUNT DISTRIBUTOR only. **MINIMUM ORDER QTY IS 2 price each **. For 9N, 2N, early 8N. (Part No: 9N12120)
$3.47

Distributor Cam and Weight Assembly - Cam and weight assembly for 8N12127B-WCR original style Side-mounted distributor. For use on models 8N after SN# 263844, 1950 thru 1952. (Part No: 8N12176)
$62.10

Distributor Cap - For tractor models 8N, 9N, 2N to #263843 all with front mount distributor. Distributor Cap. (Part No: 9N12106C)
$11.31

Distributor Cap Terminal Kit - Distributor Cap Terminal kit for 8N, 9N, 2N with front mount distributor Electronic Ignition Conversion Kit. (Part No: 1247XTTERM)
$21.35

Distributor Cap, Clip Held - Cap. Used ONLY on OLDER Tisco (Prestolite)replacement distributors (Through January 1987)for Late 8N with side mount distributor. (Part No: IBK1009)
$24.15

Distributor Cap, Clip Held - Fits Tractors: 8N SN# 263844(Side mount), Jubilee, NAA, 501, 600, 601, 700, 800, 801, 900, 901, 2000, 4000 Series (4 Cylinder) (Part No: NCA12106A)
$7.22

Distributor Clip Kit - For tractor models 8N, 9N, 2N (Early). (Part No: 9N12144)
$3.22

Distributor Coil Bail - For tractor models 8N, 9N, 2N with front mount distributor. (Part No: 9N12137)
$2.10

Distributor Drive Gear - For tractor models 8N (early), 9N, 2N. Gear for Distributor Drive (front mount distributor). (Part No: 7RA6255)
$32.09

Distributor Drive Gear - For 8N with side mount distributor, tractor serial number 263844 and above. (Part No: 7RA12390C)
$33.75

Distributor Dust Cap - Fits 4-cylinder gas engines on (1950-1964): 8N Side mount distributor, NAA, Jubilee, 600, 620, 630, 640, 650, 660, 601, 611, 621, 631, 641, 651, 661, 671, 681, 700, 740, 750, 701, 741, 771, 800, 820, 840, 801, 811, 821, 841, 851, 861, 871, 881, 900, 950, 960, 901, 941, 951, 961, 971, 981, 2000, 4000 (Part No: FAA12239A)
$4.43

Distributor Gasket Kit - For tractor models 8N, 9N, 2N prior to SN# 263844. Kit contains distributor breaker cover gasket, distibutor base gasket, distributor coil base gasket, cap gasket. (Part No: 9N12104)
$2.92

Distributor Point Set - Point set, Blue Streak premium quality. For tractor models 8N, 9N, 2N (Early). (Part No: A0NN12107ABS)
$23.67

Distributor Point Set, 4-Cylinder - For FDN12127A & 311185 distributor used on NAA, NAB, Jubilee, 8N with side mount distributor only, and 134 & 172 gas engines used on: 501, 541, 600, 601, 611, 620, 621, 630, 631, 640, 641, 650, 651, 660, 661, 671, 681, 700, 701, 740, 741, 771, 800, 801, 811, 820, 821, 840, 841, 850, 851, 860, 861, 871, 881, 900, 901, 941, 950, 951, 960, 961, 971, 981), (2000, 4000 ALL <1964). (Part No: D8NN12171AA)
$3.68

Distributor Primary Conductor - Copper. Fits tractor models Golden Jubilee, Jubilee, NAA, NAB, 1801, 1811, 1821, 1841, 1881, 2000 4 cylinder, 2030, 2031, 2111, 2130, 2131, 4000 4 cylinder, 4030, 4031, 4040, 4110, 4120, 4121, 4130, 4140, 501, 541, 600, 601, 611, 620, 621, 630, 631, 640, 641, 650, 651, 660, 661, 671, 681, 700, 701, 740, 741, 771, 800, 801, 811, 820, 821, 840, 841, 850, 851, 861, 871, 881, 900, 901, 941, 950, 951, 960, 961, 971, 981 All 4 cylinder gas, LP thru 1964, 8N sn 263844 and up 1950-1952 with side mounted distributor. Replaces: 8N12209 (Part No: 8N12209)
$4.50

Distributor Rotor - Rotor. Used ONLY on OLDER Tisco replacement distributors (Through January 1987) for Late 8N side mount Distributors. (Part No: IGP1016D)
$18.32

Distributor Rotor, Front Mount Distributor - Fits 8N, 9N, 2N with front mount distributor. (Part No: B2NN12200A)
$3.53

Distributor Shaft Assembly - Distributor shaft assembly. For use on models 8N after SN# 263844, 1950 thru 1952. Drilling is required to install distributor gear. (Part No: 8N12175)
$62.19

Distributor, Breaker Plate - 4 Cylinder. Breaker plate with points & condensor. For NAA, NAB, Jubilee, 8N with side mount distributor only, and 134 & 172 gas engines used on: 501, 541, 600, 601, 611, 620, 621, 630, 631, 640, 641, 650, 651, 660, 661, 671, 681, 700, 701, 740, 741, 771, 800, 801, 811, 820, 821, 840, 841, 850, 851, 860, 861, 871, 881, 900, 901, 941, 950, 951, 960, 961, 971, 981), (2000, 4000 ALL <1964). (Part No: FAD12152A)
$42.77

Distributor, Breaker Plate - Breaker assy, complete with points. For 8N, 9N, 2N. For front mount distributor. (Part No: 9N12150)
$28.48

Distributor, Cam and Weights Assembly - Distributor shaft with cam and weights attached for 9N12100 front mounted distributor. For use on Ford tractor models 9N, 2N, and 8N before SN# 263843, 1939 to 1950. (Part No: 9N12187)
$58.51

Electronic Ignition Conversion Kit - 6V Positive Ground - Electronic Ignition Conversion Kit - For 8N, 9N, 2N with FRONT mount distributor only. For tractors with 6-volt POSITIVE ground only. This electronic module replaces your points and condenser. Never change points again! Easy installation, no complicated wiring, fits entirely inside distributor. Increases spark plug life and horsepower, improves fuel economy. (Part No: 1247P6)
$116.77

Electronic Ignition Conversion Kit -12V Negative Ground - Complete Electronic Ignition Conversion Kit by Pertronix to convert your tractor to an electronic automotive type coil system.. For 8N, 9N, 2N with FRONT MOUNT distributor only. For tractors with 12-volt negative ground only. This electronic module replaces your points and condenser, also includes coil, coil clamp, coil wire and distributor cap. Never change points again! Easy installation, no complicated wiring, fits entirely inside distributor. Increases spark plug life and horsepower, improves fuel economy. For tractors with 12-volt negative ground only. (Part No: 1247XT)
$183.62

Electronic Ignition Conversion Kit, 12 volt negative ground - Electronic Ignition Conversion Kit - For 8N, 9N, 2N with FRONT MOUNT distributor only. For tractors with 12-volt negative ground only. This electronic module replaces your points and condenser. Never change points again! Easy installation, no complicated wiring, fits entirely inside distributor. Increases spark plug life and horsepower, improves fuel economy. For tractors with 12-volt negative ground only. (Part No: 1247)
$107.78

Electronic Ignition Conversion Kit, 12V Negative Ground - Pertronix Electronic Ignition kit for the following tractors using 4-cylinder gas engine: 8N (using side mount distributor), NAA, Jubilee, (501, 600, 620, 630, 640, 650, 660, 601, 611, 621, 631, 641, 651, 661, 671, 681, 700, 800, 900, Series), 2000. And for the following tractors using 172 4-cylinder gas engine: 800, 900, 801, 901, 4000. This electronic module by Pertronix replaces your points and condenser. Never change points again! Easy installation, no complicated wiring, fits entirely inside distributor. Increases spark plug life and horsepower, improves fuel economy. For tractors with 12-volt negative ground only. (Part No: 1244A)
$88.52

Electronic Ignition Conversion Kit, 6V Positive Ground - For 8N with side mount distributor only. This electronic module kit by Pertronix replaces your points and condenser. Never change points again! Easy installation, no complicated wiring, fits entirely inside distributor. Increases spark plug life and horsepower, improves fuel economy. For tractors with 6-volt positive ground only. (Part No: 1244AP6)
$95.84

Generator, 6 Volt - New generator with pulley for 8N, 9N, 2N, (2000, 3000, 4000 prior to 1965). Single terminal, 6 Volt. (Part No: 8N10000)
$82.73

Generator, 6 Volt - Remaufactured, 2 wire, threaded shaft with pulley. For model 8N 1947-48. (Part No: 8N10000A)
$215.71

Generator, 6 Volt - For tractor models 8N, 9N, 2N 1939-1950. Remanufactured Generator. Pulley NOT included 4 3/4" O.D. housing, 2 brush, 3 terminal, keyed shaft. Refundable $45.00 core charge will be added to your order. IF ORDERING ON-LINE, THIS ADDITIONAL CHARGE WILL BE ADDED TO YOUR ORDER AFTER YOUR RECEIPT IS PRINTED. Replaces OEM # 8N10000B. (Part No: 8N10000BR)
$295.01

Ignition Kit - Ignition kit, less rotor. Contains points, gauge, and condenser for Front Mount Distributor. For 8N, 9N, 2N (Part No: ATK6FF)
$9.00

Ignition Kit - 4 Cylinder - Ignition kit, less rotor. Contains points, gauge, and condenser. For tractor models 1950 to 1964. For 2000, 4000, 600, 6000, 6100, 700, 800, 8N (late), 900, NAA (Part No: ATK7FA)
$7.23

Ignition Kit With Rotor - 4 Cylinder - Ignition kit contains: points, rotor, condensor. For 8N (LATE - with side mounted distributor), NAA, Jubilee, 501, 600, 620, 630, 640, 650, 660, 601, 611, 621, 631, 641, 651, 661, 671, 681, 700, 740, 750, 701, 741, 771, 800, 820, 840, 801, 811, 821, 841, 851, 861, 871, 881, 900, 950, 960, 901, 941, 951, 961, 971, 981, 2000, 4000. For tractor models from 1950 to 1964 (4 Cylinder). Also for TISCO 8N12127-WCR distribution. (Part No: ATK7FAR)
$9.12

Ignition Tune-Up Kit And Maintenance Kit - Comprehensive kit For 8N, 9N, 2N, using front mount distributors to SN# 263843. Complete Tune-Up and maintenance Kit includes: Universal spark plug wire set, distributor cap, heavy duty point set, condenser, heavy duty rotor, heat range matched spark plugs, oil filter, Fuel Sediment Bowl Assembly, and Fuel Filter, In-Line, 5/16 inch . Note: If your 8N has an angle mounted distributor refer to part #TUNEMAINT8N instead. (Part No: 2N9NTUNEMAINT)
$90.03

Ignition Tune-Up Kit And Maintenance Kit - For 8N (SN# 263844 & up), NAA, Jubilee (4 Cylinder Gas Engine). Comprehensive Kit includes: Universal spark plug wire set, distributor cap, heavy duty point set, condenser, heavy duty rotor, Spark plugs, Oil Filter APN6731B, Fuel Sediment Bowl Assembly, and Fuel Filter, In-Line, 5/16 inch . (Part No: TUNEMAINT8N)
$75.77

Ignition Tune-Up Kit, Front Mount Distributor - For 8N, 9N, 2N, using front mount distributors to SN# 263843. Complete Comprehensive Tune-Up Kit includes: Universal spark plug wire set, distributor cap, heavy duty point set, condenser, heavy duty rotor, heat range matched spark plugs. Note: If your 8N has an angle mounted distributor refer to #TUNEkit instead. (Part No: 2N9NTUNEKIT)
$42.59

Key Switch - For all Fords 1939 through 1964 except Dexta and Fordson Major with 3/4 inch hole. Keyed Ignition Switch comes with 2 keys (Part No: 8N3679C)
$6.63

Pertronix Distributor Cap - Pertronix Distributor Cap for 8N, 9N, 2N with front mount distributor that has been converted to Electronic Ignition using kit 1247XT. (Part No: 1247XTCAP)
$29.91

Point Set - Point set. Used ONLY on OLDER Tisco replacement distributors (Through January 1987) for Late 8N side mount Distributors. (Part No: IGS2224LB)
$6.75

Pulley Alternator, Wide - For use with our 12 Volt Conversion kits that use the 10SI style alternator only. .670 inch Bore, 2.5 inch outside diameter, using a 5/8 inch wide belt. Replaces the narrower pulley (3/8ths aprox)on tractors with a wider crankshaft pulley (3/4 inch). (Part No: AFD5035)
$14.97

Pulley Generator - Fits 8N (Keyway). Shaft hole is approximately 0.67" (approximately 11/16). Pulley O.D. approximately 3-5/8", I.D. approx. 2 5/16" X 5/8 wide. (Part No: 8N10130A)
$6.38

Pulley Generator - Generator pulley (threaded). For 8N, 9N, 2N (Part No: 9N10130B)
$8.93

Resistor - For 8N, 9N, 2N, and 4 cylinder engines on 600 - 4000 tractors 1955-1964. Used in ignition system with 12-volt square coil, resistance = .6 ohms. (Part No: 8NE10306)
$2.98

Resistor Assembly - For tractor models 8N to SN# 263844. Resistor measures .6 ohms +/- .1 (Part No: A8NN12250A)
$15.75

Rotor Clip - For tractor models (8N SN# 263844 and up), NAA, 501, 600, 700, 800, 900, 1801, (2000, 4000 4 cylinder through 1964). All with side mounted distributor. (Part No: 8N12213)
$2.62

Rotor, Side Mount Distributor - 4-Cylinder. Fits the following gas tractors up to 1964: 8N with side mount distributor, NAA, Jubilee, 600, 620, 630, 640, 650, 660, 601, 611, 621, 631, 641, 651, 661, 671, 681, 700, 740, 750, 701, 741, 771, 800, 820, 840, 801, 811, 821, 841, 851, 861, 871, 881, 900, 950, 960, 901, 941, 951, 961, 971, 981, 2000, 4000. (Part No: C0NN12200A)
$3.00

Rubber Grommet - Rubber grommet, starter switch wire {goes on lower left side of instrument panel}. Tractors: 8N, NAA {1948-1952}. (Part No: 11A14605)
$3.70

Spark Plug - For 8N, 9N, 2N, NAA, NAB, Jubilee, and 134 & 172 gas engines used on: 501, 541, 600, 601, 611, 620, 621, 630, 631, 640, 641, 650, 651, 660, 661, 671, 681, 700, 701, 740, 741, 771, 800, 801, 811, 820, 821, 840, 841, 850, 851, 860, 861, 871, 881, 900, 901, 941, 950, 951, 960, 961, 971, 981), (2000, 4000 ALL before 1964). SPARK PLUG. Price is for EACH. Minimum Order is 4. (Part No: AL437)
$2.38

Spark Plug Wire Bracket - For tractors: 8N {1950-1952}. (Part No: 8N12112B)
$9.06

Spark Plug Wire Bracket - ****SOLD IN MULTIPLE OF 2, PRICE SHOWN IS PER BRACKET**** For tractor models 8N, 9N, 2N, (1939 to 1950). ****SOLD IN MULTIPLE OF 2, PRICE SHOWN IS PER BRACKET**** (Part No: 9N14564)
$11.34

Spark Plug Wire Set, Custom - Premium quality wire set for 8N with side mount distributor. Solic brass distributor coils, Zinc-coated plug terminals, Tin-coated copper core, boots constructed from EPDM rubber and dual-jacket insulation. Meets SAE J2031 Specifications. Made in the USA. (Part No: 8N12259)
$12.38

Spark Plug Wire Set, Universal, 4 Cyl. - Universal Spark Plug Wire Set, 4 Cylinder, 90 degree boot, cut to length. Longest Reach is 33 inches. Solid brass distributor coils, Zinc-coated plug terminals, tin-coated copper core, boots constructed from EPDM rubber and dual-jacket insulation. Meets SAE J2031 Specifications. Made in the USA. (Part No: CPN12259)
$13.59

Starter Boot - Rubber cover, starter control wire terminal {goes on wire to solenoid}. For tractors: 8N, Jubilee, NAA {1948-1954}. For 321, 339, 340, 501 (Part No: 8N11115)
$12.03

Starter Boot - Rubber cover, starter switch terminal cover. Tractors {1948-1958}. (Part No: 8N11113)
$4.50

Starter Copper Strap, Solenoid to Starter - Fits 8N. (Part No: 8N11518)
$4.67

Starter Drive - New improved design starter drive, for 8N, 9N, 2N (1939 to 1952). (Part No: 52-11350C)
$19.43

Starter Repair Kit - For 8N, 9N, 2N. Starter Repair Kit contains all parts necessary for repair of starter #8N11001. (Part No: SRK401)
$13.08

Starter Solenoid - This Starter Solenoid (Relay Assembly)will work for 6 or 12 volt applications. It has three posts and a saddle mount. For 8N, 1948-1952. (Part No: 8N11450)
$7.49

Starter Switch - With mounting gasket. Fits 8N (1948-1952);all except Select-O-Matic tractors. Also NAA, Jubilee, 501, 600, 700, 800, 900, 2000, 4000, all 1953-1964. Replaces 8N11550 (Part No: 8N11500WG)
$20.25

Starter, 12 Volt, With Drive - New Starter for 8N, 9N, 2N. 12 Volt. Complete starter includes drive mechanism. (Part No: 8N1100R)
$110.33

Starter, 6 Volt, Less Drive - Starter, less drive. For 8N, 9N, 2N, with 6 volt systems. Restoration quality. (Part No: 8N11001)
$91.01

Starter, 6 Volt, With Drive - New Starter for 8N, 9N, 2N. 6 Volt.Complete starter - includes drive mechanism. Replaces OEM # 8N11001R. (Part No: 8N11001WD)
$110.33

Terminal Block - For tractor models 8N 1950-52, Jubilee, NAA, (2000, 4000 up to 1964), 600, 620, 630, 640, 650, 660, 800, 820, 840. (Part No: 8NNN14448A)
$7.35

Tune Kit - This Tune Kit is for tractor models 9N, 9N, 2N, and Early 8N, all with Front Mount Distributor. Tune Up Kit, Autolite. Includes: Point set, Condenser, Rotor & (4) 437 Autolite Spark Plugs and gaskets. (Part No: 309786)
$20.85

Tune Kit, Basic - This Basic Tune kit points, condenser and rotor for Front Mount Distributor. For 9N, 2N and Early 8N. (Part No: ATK6FFR)
$14.01

Tune Kit, Basic - This Basic Ignition Tune Kit is for 4 cylinder gas tractor models NAA, NAB, Jubilee, 8N with side mount distributor only, and 134 & 172 gas engines used on: 501, 541, 600, 601, 611, 620, 621, 630, 631, 640, 641, 650, 651, 660, 661, 671, 681, 700, 701, 740, 741, 771, 800, 801, 811, 820, 821, 840, 841, 850, 851, 860, 861, 871, 881, 900, 901, 941, 950, 951, 960, 961, 971, 981), (2000, 4000 ALL <1964). Tune Up Kit, Autolite. Kit contains: D8NN12171AA Point Set, FET12300A Condenser, CONN12200A Rotor & Spark Plugs. (Part No: 309787)
$15.55

Tune Kit, Basic - This Basic Tune Kit for a 4 cylinder gas contains Premium Blue Streak points (A0NN12107ABS), rotor, condenser, and gauge for front mount distributor on 2N, Early 8N, and 9N. (Part No: APN12000ABSR)
$33.13

Tune Kit, Comprehensive - This Comprehensive Tune Kit is for 4 cylinder gas models 8N (SN# 263844 & up), NAA, Jubilee, 600, 620, 630, 640, 650, 660, 601, 611, 621, 631, 641, 651, 661, 671, 681, 700, 740, 750, 701, 741, 771, 800, 820, 840, 801, 811, 821, 841, 851, 861, 871, 881, 900, 950, 960, 901, 941, 951, 961, 971, 981, 2000, 4000, 1950 thru 1964. (4 Cylinder Gas Engines). Comprehensive Tune-Up Kit includes: Universal spark plug wire set, distributor cap, heavy duty point set, condenser, heavy duty rotor, and spark plugs. (For use with original equipment distributors). (Part No: TUNEKIT)
$42.90

Voltage Regulator - For 8N - For Early Models with Front Mount Distributor (Part No: 8N10505B)
$19.42

Voltage Regulator - For 8N - Side Distributor, with generator. (Part No: 8N10505C)
$17.92

Wiring Harness 12 Volt - For Late 8N. 12 Volt Wiring Harness for those tractors converted to 12 Volts. This is main engine wiring only. (Part No: 8NL10301)
$20.92

Wiring Harness 12 Volt - Wiring harness for 2N, Early 8N, and 9N that has been converted to 12 Volt. Does not include light wiring. (Part No: 8NE10301)
$20.92

Wiring Harness, 6 Volt - Has woven fabric casing. For 8N with front mounted distributor and 2 wire generator, up to SN# 263843. Ignition wiring harness. (Part No: 8N14401B)
$17.80

Wiring Harness, 6 Volt - Has woven fabric casing. For 8N Side mount distributor, SN# 263843 and up. Ignition wire harness. Replaces 8N14401C (Part No: 8N14401C)
$20.37

Wiring Harness, 6 Volt - Has vinyl wrapped casing. For 8N Side mount distributor, SN# 263843 and up. Ignition wire harness. Replaces 8N14401C (Part No: 8N14401CP)
$14.63

Wiring Harness, Restoration Quality - Complete wiring harness including light wires and a diagram, 6 Volt. Original style braiding with soldered terminals. Made in the USA. For model 8N up to SN# 263843 with front mount distributor. (Part No: 8N14401B-OE)
$169.88

Engine Bearings
Main Bearing Set, .010 - .010" main bearing kit. 1 kit used per engine. Contains center, front, and rear bearings. For 8N, 9N, 2N (Part No: MBK9N633E-010)
$37.50

Main Bearing Set, .020 - .020" main bearing kit. 1 kit used per engine. Contains center, front, and rear bearings. For 8N, 9N, 2N (Part No: MBK9N633G-020)
$37.50

Main Bearing Set, .030 - .030" main bearing kit. 1 kit used per engine. Contains center, front, and rear bearings. For 8N, 9N, 2N (Part No: MBK9N633-030)
$37.50

Main Bearing Set, .040 - This .040 oversize Main Bearing Set is complete for 1 engine. Contains center, front, and rear bearings. For tractor models 8N, 9N, 2N. (Part No: MBK9N633-040)
$37.50

Main Bearing Set, .060 - 1 kit used per engine. Contains center, front, and rear bearings. For tractor models 2N, 8N, and 9N. (Part No: MS-120P-060)
$59.62

Main Bearing Set, Standard - Standard main bearing kit. 1 kit used per engine. Contains center, front, and rear bearings. For 8N, 9N, 2N (Part No: MBK9N633A-STD)
$37.50

Rod Bearing Pair, .001 - For tractor models 8N, 9N, 2N. 1 Pair for one Rod. (Part No: 9N6211B-PAIR)
$11.33

Rod Bearing Pair, .002 - For tractor models 8N, 9N, 2N. 1 Pair for one Rod. (Part No: 9N6211C-PAIR)
$10.70

Rod Bearing Pair, .010 - For tractor models 8N, 9N, 2N. 1 Pair for one Rod. (Part No: 9N6211E-PAIR)
$10.70

Rod Bearing Pair, .020 - For tractor models 8N, 9N, 2N. 1 Pair for one Rod. (Part No: 9N6211G-PAIR)
$10.70

Rod Bearing Pair, .030 - For tractor models 8N, 9N, 2N. 1 Pair for one Rod. (Part No: 9N6211-030-PAIR)
$10.70

Rod Bearing Pair, .040 - For tractor models 8N, 9N, 2N. 1 Pair for one Rod. (Part No: 9N6211-040-PAIR)
$10.70

Rod Bearing Pair, Standard - With journal size of 2.095 inches. For tractor models 8N, 9N, 2N. 1 Pair for one Rod. Must be ordered in lots of 4. (Part No: 9N6211A-PAIR)
$10.70

Rod Bearing Set, .010 - .010" connecting rod bearing kit. 1 kit used per engine. Contains 4 pair of 9N6211E. For 8N, 9N, 2N (Part No: CRK9N6211E-010)
$22.80

Rod Bearing Set, .020 - .020" connecting rod bearing kit. 1 kit used per engine. Contains 4 pair of 9N6211G. For 8N, 9N, 2N (Part No: CRK9N6211G-020)
$39.05

Rod Bearing Set, .030 - .030" connecting rod bearing kit. 1 kit used per engine. Contains 4 pair of 9N6211-030. For 8N, 9N, 2N (Part No: CRK9N6211-030)
$39.05

Rod Bearing Set, .040 - .040" connecting rod bearing kit. 1 kit used per engine. Contains 4 pair of 9N6211-040. For 8N, 9N, 2N (Part No: CRK9N6211-040)
$23.68

Rod Bearing Set, Standard - With Journals measuring 2.095 inches. Connecting rod bearing kit. 1 kit used per engine. Contains 4 pair of 9N6211E. For 8N, 9N, 2N. (Part No: CRK9N6211A-STD)
$22.50

Rod Bearing, .060 - Individual Rod Bearing 1 pr. For model 8N, 9N, 2N. 4 Required per engine. (Part No: CB-200P-060)
$11.59

Engine Gaskets
Crankshaft Seal, Front - Rope seal, front. Upper and lower is the same part. For tractor models 8N, 9N, 2N. PRICE IS FOR EACH AND YOU MUST ORDER 2. Replaces 8N6700 and 8N6707. (Part No: 8N6700)
$3.49

Crankshaft Seal, Front, Upper - Use 8n6700 (Part No: 8N6707)
$3.49

Crankshaft Seal, Rear - Rope seal, rear. Upper and lower is the same part. For tractor models 8N, 9N, 2N. PRICE IS FOR EACH AND YOU MUST ORDER 2. Replaces 8N6701 and 8n6702. (Part No: 8N6701)
$3.57

Distributor Breaker Cover Gasket - For tractor models 9N, Early 8N, 2N. SOLD IN QUANTITIES OF 10, PRICE IS FOR 1. (Part No: 9N12276)
$1.07

Distributor Gasket kit - For tractor models 8N, 9N, 2N prior to SN# 263844. Kit contains distributor breaker cover gasket, distibutor base gasket, distributor coil base gasket, cap gasket. (Part No: 9N12104)
$2.92

Exhaust Manifold Gasket - SINGLE gasket (TWO gaskets required) for exhaust manifold on 8N, 9N, 2N. (Part No: 9N9448)
$0.98

Full Gasket Set - Full Engine Overhaul Gasket Set with metal head gasket. Comes WITHOUT front and side timing cover gaskets. For tractor models 8N, 9N, 2N. (Part No: 8N6008M)
$30.91

Governor Housing Mounting Cover Gasket - For tractor models 8N, 9N, 2N. (Part No: 9N6022)
$1.03

Head Gasket - Head gasket. All soft material except for the fire rings. For tractor models 8N, 9N, 2N. (Part No: 8N6051A)
$9.86

Head Gasket - Head gasket, all metal. For 8N, 9N, 2N (Part No: 8N6051B)
$8.38

Oil Pan Gasket Set - For 8N, 9N, 2N; through 1964. 7 Piece Set. Oil Pan Gasket Set with upper and lower crankshaft rope seals, left and right oil pan gaskets, and oil pan drain plug gasket. (Part No: 9N6781)
$12.51

Timing Gear Front Cover Gasket - For tractor models 9N, 2N, (8N prior to SN# 263844). **minimum order quantity of 5** (Part No: 9N6020A)
$1.84

Timing Gear Front Cover Gasket - For model 8N SN# 263844 and up. (Part No: 8N6020C)
$1.93

Timing Gear Side Cover Gasket - For tractor models 9N, 8N, 2N. **minimum order quantity of 5** (Part No: 8N6018)
$0.54

Upper Gasket Set - For tractor models 8N, 9N, 2N. Upper Gasket Set with Metal Head Gasket.Set includes: cylinder head gasket, (2) valve cover side plate gaskets, (8) valve guide seals, (2) manifold gaskets, (1) governor gasket. Replaces: 8BA6571, 9N6022, 9N9448, 7HA6521, 8N6051A (Part No: VG8NM)
$18.51

Valve Cover Gasket - Price is for each, minimum order quantity is 2. For tractor models 8N, 9N, 2N. (Part No: 7HA6521)
$.74

Engine Rebuild Kits
Basic In Frame Overhaul Kit, 120 Gas - For 120 CID 4 cylinder gas 3-3/16" standard bore. Basic in frame kit contains, thick wall .090" sleeves, 3 ring pistons, rings, pin & retainers, valve grind gasket kit, pan gasket kit. Bearings are available, must be ordered separately. For tractor models 8N, 9N, 2N. (Part No: BIFF106A)
$202.63

Basic In Frame Overhaul Kit, 120 Gas - Made by TISCO. 120 CID 4 cylinder gas 3-3/16" standard bore. Kit contains thin wall .040" sleeve, 3 ring pistons, rings, pin & retainers, valve grind gasket kit, pan gasket kit. Kit does not include bearings. For tractor models 8N, 9N, 2N. (Part No: BIFF103A)
$222.28

Basic In Frame Overhaul Kit, 120 Gas - Made by TISCO. 120 CID 4 cylinder gas 3-3/16" standard bore. Basic in frame kit contains, thin wall .040" sleeves 4 ring pistons, rings, pin & retainers, valve grind gasket kit, pan gasket kit. For tractor models 8N, 9N, 2N. (Part No: BIFF102A)
$244.04

Basic In Frame Overhaul Kit, 120 Gas - Made by TISCO. 120 CID 4cylinder gas 3-3/16" standard bore. Basic engine kit contains, thick wall .090" sleeves, 4 ring pistons, rings, pin & retainers, valve grind gasket kit, pan gasket kit. Bearings are available, must be ordered separately. For tractor models 8N, 9N, 2N. (Part No: BIFF105A)
$241.39

Basic Overhaul Kit, 120 Gas, 3-ring pistons, .040 Sleeves - Made by TISCO. 120 CID 4 cylinder gas 3-3/16" standard bore. Basic engine kit contains, thin wall .040" sleeves, 3 ring pistons, rings, pin & retainers, pin bushings, complete gasket kit. Bearings NOT included & must be ordered separately. For tractor models 8N, 9N, 2N. (Part No: BEKF103A-LCB)
$233.15

Basic Overhaul Kit, 120 Gas, 3-ring pistons, .090 Sleeves - Made by TISCO. 120 CID 4 cylinder gas 3-3/16" standard bore. Basic engine kit contains, thick wall .090" sleeves, 3 ring pistons, rings, pin & retainers, pin bushings, complete gasket kit. Bearings NOT included & must be ordered separately. For tractor models 8N, 9N, 2N. (Part No: BEKF106A-LCB)
$179.40

Basic Overhaul Kit, 120 Gas, 4-Ring Pistons, .090 Sleeves - Made by TISCO. 120 CID 4 cylinder gas 3-3/16" standard bore. Basic engine kit contains, thick wall .090" sleeves, 4 ring pistons, rings, pins & retainers, pin bushings, complete gasket kit. Bearings NOT included & must be ordered separately. For tractor models 8N, 9N, 2N. (Part No: BEKF105A-LCB)
$252.26

Basic Overhaul Kit, 120 Gas, 4-ring Pistons, .040 Sleeves - Made by TISCO. 120 CID 4 cylinder gas 3-3/16" standard bore. Basic engine kit contains, thin wall .040" sleeves, 4 ring pistons, rings, pins & retainers, pin bushings, complete gasket kit. Bearings NOT included & must be ordered separately. For 8N, 9N, 2N. (Part No: BEKF102A-LCB)
$254.91

Engine Overhaul Kit, 120 Gas - Made by TISCO. 120 CID 4 cylinder gas 3-3/16" standard bore. Engine overhaul kit contains, thin wall .040" sleeves, 3 ring pistons, rings, pin & retainers, pin bushings, complete gasket kit, intake & exhaust valves, valve springs & retainers, guides & retainers, valve keys. For tractor models 8N, 9N, 2N. NOTE: Please indicate in comments if you have rotating valves, (4) 8N6505C & (4) 8N6534B will be added to the order for an additional special price of $85.00. IF ORDERING ON-LINE, THIS ADDITIONAL CHARGE WILL BE ADDED TO YOUR ORDER AFTER YOUR RECEIPT IS PRINTED. If your keepers or keys on the exhaust or intake valves are the same, you DO NOT have rotating valves. If they are different then you DO. Bearings not included, they can be ordered separately from our Engine Bearings category. (Part No: EOK103-LCB)
$353.64

Engine Overhaul Kit, 120 Gas - Made by TISCO. 120 CID 4 cylinder gas 3-3/16" standard bore. Engine overhaul kit contains, thick wall .090" sleeves, 4 ring pistons, rings, pin & retainers, pin bushings, complete gasket kit, intake & exhaust valves, valve springs & retaineres, guides & retainers, valve keys. Bearings NOT included & must be ordered separately. For tractor models 8N, 9N, 2N. NOTE: Please indicate in comments if you have rotating valves, (4) 8N6505C & (4) 8N6534B will be added to the order for an additional special price of $85.00. IF ORDERING ON-LINE, THIS ADDITIONAL CHARGE WILL BE ADDED TO YOUR ORDER AFTER YOUR RECEIPT IS PRINTED. If your keepers or keys on the exhaust or intake valves are the same, you DO NOT have rotating valves. If they are different then you DO. Bearings not included, they can be ordered separately from our Engine Bearings category. (Part No: EOK105-LCB)
$416.41

Engine Overhaul Kit, 120 Gas - Made by TISCO. 120 CID 4 cylinder gas 3-3/16" standard bore. Engine overhaul kit contains, thick wall .090" sleeves, 3 ring pistons, rings, pin & retainers, pin bushings, complete gasket set, intake & exhaust valves, valve springs & retainers, guides & retainers, valve keys. For 8N, 9N, 2N. NOTE: Please indicate in comments if you have rotating valves, (4) 8N6505C & (4) 8N6534B will be added to the order for an additional special price of $85.00. IF ORDERING ON-LINE, THIS ADDITIONAL CHARGE WILL BE ADDED TO YOUR ORDER AFTER YOUR RECEIPT IS PRINTED. If your keepers or keys on the exhaust or intake valves are the same, you DO NOT have rotating valves. If they are different then you DO. Bearings not included, they can be ordered separately from our Engine Bearings category. (Part No: EOK106-LCB)
$360.81

Overhaul Kit, Comprehensive - GUIDE - TO DETERMINE WHICH OF THE BELOW KITS YOU WILL NEED, YOU NEED TO KNOW THE FOLLOWING: (1) If your pistons have 3 or 4 rings per piston. (2) If your piston sleeve thickness is .040 or .090 inches. (3) If your oil pump gear is 3/4 or 9/16 inches wide. (4) If you have rotating or non-rotating exhaust valves - If your keepers or keys on the exhaust and intake valves are the same, you DO NOT have rotating valves. If your keepers or keys on the exhaust and intake valves are the different, you DO have rotating valves. Engine bearings can be ordered from our ENGINE BEARINGS category. NOTE

Overhaul Kit, Comprehensive, 120 Gas - 3 RING PISTONS, .090 SLEEVES, 3/4 OIL PUMP GEAR WIDTH. Made by TISCO. Complete engine kit. Contains, thick wall .090" sleeves, 3 ring pistons, rings, pins & retainers, pin bushings, complete gasket set, timing gear, intake & exhaust valves, springs, spring retainers, guides, retainers & seals, valve keys, upper & lower radiator hose, air cleaner hose, oil pump kit, fan belt, points & condenser, spark plugs, oil filter, basic carb kit. For tractor models 8N, 9N, 2N. NOTE: Please indicate in comments if you have rotating valves, (4) 8N6505C & (4) 8N6534B will be added to the order for and additional special price of $85.00. IF ORDERING ON-LINE, THIS ADDITIONAL CHARGE WILL BE ADDED TO YOUR ORDER AFTER YOUR RECEIPT IS PRINTED. If your keepers or keys on the exhaust or intake valves are the same, you DO NOT have rotating valves. If they are different then you DO. Bearings not included, they can be ordered separately from our Engine Bearings category. (Part No: 3-8H-LCB)
$455.88

Overhaul Kit, Comprehensive, 120 Gas - Made by TISCO. 120 CID 4 cylinder gas 3-3/16" standard bore, 3/4" oil pump gear width, Complete engine kit contains, thin wall .040" sleeves, 3 ring pistons, rings, pins & retainers, pin bushings, complete gasket kit, timing gear, intake & exhaust valves, springs, spring retainers, guides, retainers & seals, valve keys, upper & lower radiator hose, air cleaner hose, oil pump kit, fan belt, points & condenser, spark plugs, oil filter, basic carb kit. For tractor models 8N, 9N, 2N. NOTE: Please indicate in comments if you have rotating valves, (4) 8N6505C & (4) 8N6534B will be added to the order for an additional special price of $85.00. IF ORDERING ON-LINE, THIS ADDITIONAL CHARGE WILL BE ADDED TO YOUR ORDER AFTER YOUR RECEIPT IS PRINTED. If your keepers or keys on the exhaust or intake valves are the same, you DO NOT have rotating valves. If they are different then you DO. Bearings not included, they can be ordered separately from our Engine Bearings category. (Part No: 3-8T-LCB)
$487.94

Overhaul Kit, Comprehensive, 120 Gas - Made by TISCO. 120 CID 4 cylinder gas 3-3/16" standard bore, 9/16" oil pump gear width. Complete engine kit contains, thick wall .090" sleeves, 3 ring pistons, rings, pins & retainers, pin bushings, complete gasket kit, timing gear, intake & exhaust valves, springs, spring retainers, guides, retainers & seals, valve keys, upper & lower radiator hose, air cleaner hose, oil pump kit, fan belt, points & condenser, spark plugs, oil filter, basic carb kit. For, 8N, 9N, 2N. NOTE: Please indicate in comments if you have rotating valves, (4) 8N6505C & (4) 8N6534B will be added to the order for an additional special price of $85.00. IF ORDERING ON-LINE, THIS ADDITIONAL CHARGE WILL BE ADDED TO YOUR ORDER AFTER YOUR RECEIPT IS PRINTED. If your keepers or keys on the exhaust or intake valves are the same, you DO NOT have rotating valves. If they are different then you DO. Bearings not included, they can be ordered separately from our Engine Bearings category. (Part No: 3-9H-LCB)
$423.88

Overhaul Kit, Comprehensive, 120 Gas - Made by TISCO. 120 CID 4 cylinder gas 3-3/16" standard bore, 9/16" oil pump gear width. Complete engine kit contains, thin wall .040" sleeves, 3 ring pistons, rings, pins, retainers, pin bushings, complete gasket kit, timing gear, intake & exhaust valves, springs, spring retainers, guides, retainers & seals, valve keys, upper & lower radiator hose, air cleaner hose, oil pump kit, fan belt, points & condenser, spark plugs, oil filter, basic carb kit. For tractor models 8N, 9N, 2N. NOTE: Please indicate in comments if you have rotating valves, (4) 8N6505C & (4) 8N6534B will be added to the order for an additional special price of $85.00. IF ORDERING ON-LINE, THIS ADDITIONAL CHARGE WILL BE ADDED TO YOUR ORDER AFTER YOUR RECEIPT IS PRINTED. If your keepers or keys on the exhaust or intake valves are the same, you DO NOT have rotating valves. If they are different then you DO. Bearings not included, they can be ordered separately from our Engine Bearings category. (Part No: 3-9T-LCB)
$426.56

Overhaul Kit, Comprehensive, 120 Gas - Made by TISCO. 120 CID 4 cylinder gas 3-3/16" standard bore, 3/4" oil pump gear width. Complete engine kit contains, thick wall .090" sleeves, 4 ring pistons, rings, pins & retainers, pin bushings, complete gasket kit, timing gear, intake & exhaust valves, springs, spring retainers, guides, retainers & seals, valve keys, upper & lower radiator hose, air cleaner hose, oil pump kit, fan belt, points & condenser, spark plugs, oil filter, basic carb kit. For tractor models 8N, 9N, 2N. NOTE: Please indicate in comments if you have rotating valves, (4) 8N6505C & (4) 8N6534B will be added to the order for an additional special price of $85.00. IF ORDERING ON-LINE, THIS ADDITIONAL CHARGE WILL BE ADDED TO YOUR ORDER AFTER YOUR RECEIPT IS PRINTED. If your keepers or keys on the exhaust or intake valves are the same, you DO NOT have rotating valves. If they are different then you DO. Bearings not included, they can be ordered separately from our Engine Bearings category. (Part No: 4-8H-LCB)
$503.93

Overhaul Kit, Comprehensive, 120 Gas - Made by TISCO. 120 CID 4 cylinder gas 3-3/16" standard bore, 3/4" gear width. Complete engine kit contains, thin wall .040" sleeves, 4 ring pistons, rings, pins & retainers, pin bushings, complete gasket kit, timing gear, intake & exhaust valves, springs, spring retainers, guides, guide retainers & seals, valve keys, upper & lower radiator hose, air cleaner hose, oil pump kit, fan belt, points & condenser, spark plugs, oil filter, basic carburetor kit. For tractor models 8N, 9N, 2N. NOTE: Please indicate in comments if you have rotating valves, (4) 8N6505C & (4) 8N6534B will be added to the order for an additional special price of $85.00. IF ORDERING ON-LINE, THIS ADDITIONAL CHARGE WILL BE ADDED TO YOUR ORDER AFTER YOUR RECEIPT IS PRINTED. If your keepers or keys on the exhaust or intake valves are the same, you DO NOT have rotating valves. If they are different then you DO. Bearings not included, they can be ordered separately from our Engine Bearings category. (Part No: 4-8T-LCB)
$506.16

Overhaul Kit, Comprehensive, 120 Gas - Made by TISCO. 120 CID 4 cylinder gas 3-3/16" standard bore, 9/16" gear width. Complete engine kit contains, thin wall .040" sleeves, 4 ring pistons, rings, pins & retainers, pin bushings, complete gasket kit, timing gear, intake & exhaust valves, springs, spring retainers, guides, guide retainers & seals, valve keys, upper & lower radiator hose, air cleaner hose, oil pump kit, fan belt, point & condenser, spark plugs, oil filter, basic carburetor kit. For 8N, 9N, 2N. NOTE: Please indicate in comments if you have rotating valves, (4) 8N6505C & (4) 8N6534B will be added to the order for an additional special price of $85.00. IF ORDERING ON-LINE, THIS ADDITIONAL CHARGE WILL BE ADDED TO YOUR ORDER AFTER YOUR RECEIPT IS PRINTED. If your keepers or keys on the exhaust or intake valves are the same, you DO NOT have rotating valves. If they are different then you DO. Bearings not included, they can be ordered separately from our Engine Bearings category. (Part No: 4-9T-LCB)
$443.63

Overhaul Kit, Comprehensive, 120 Gas, 4-ring Pistons, .090 Sleeves - 4 RING PISTONS, .090 SLEEVES, 9/16 OIL PUMP GEAR WIDTH. Made by TISCO. Complete engine kit contains, thick wall .090" sleeves, 4 ring pistons, rings, pins & retainers, pin bushings, complete gasket kit, intake & exhaust valves, springs, spring retainers, guides, retainers & seals, valve keys, upper & lower radiator hose, air cleaner hose, oil pump kit, timing gear, fan belt, points & condenser, spark plugs, oil filter, basic carb kit. For, 8N, 9N, 2N. NOTE: Please indicate in comments if you have rotating valves, (4) 8N6505C & (4) 8N6534B will be added to the order for an additional special price of $85.00. IF ORDERING ON-LINE, THIS ADDITIONAL CHARGE WILL BE ADDED TO YOUR ORDER AFTER YOUR RECEIPT IS PRINTED. If your keepers or keys on the exhaust or intake valves are the same, you DO NOT have rotating valves. If they are different then you DO. Bearings not included, they can be ordered separately from our Engine Bearings category. (Part No: 4-9H-LCB)
$505.70

Valve Overhaul Kit - Made by TISCO. For servicing one engine when valve replacement is necessary. For 8N, 9N, 2N with solid guides, free-rotating exhaust valves. Kit contains intake valves, exhaust valves, valve springs and keys, solid type valve guides and rotating valve kit. (Part No: VOKF928NFR)
$155.93

Valve Overhaul Kit - Fits 9N, 2N& 8N that use solid valve guides and have NON-rotating exhaust valves. Includes Intake & exhaust valves, springs, keys, and guides. (Part No: VOKF928N)
$144.18

Engine Parts
Camshaft - For press on gear. Fits 8N SN# 263843 and greater using SIDE mount distributor. (Part No: 8N6250)
$147.96

Camshaft Kit, Side Mount Distributor Engine - Includes: NEW Camshaft with Distributor Gear & Lifters For 8N with Side Mount Distributor (Part No: R0885K)
$264.72

Camshaft, New - For tractor models: 8N, 9N, 2N with front mount distributor before s/n 263844. (Part No: 2N6250B)
$344.59

Camshaft, Reground - For Model: 8N with side mount distributor. Replaces 8N6250. (Part No: R1188895)
$100.00

Crankshaft - New kit with bearings. For tractor models 8N, 9N, 2N With STD Rod And Main Bearings. (Part No: 9N6303ACK)
$788.45

Crankshaft - Reground With Bearings. Fits Ford 8N, 9N, 2N. Reground Crankshaft. A refundable $75.00 core charge will added to your order. Additional $28 shipping due to size and weight. Additional shipping will be added after your confirmation is printed if you order on-line. (Part No: 1198019)
$551.80

Crankshaft - NEW crankshaft for tractor models 9N, 8N, 2N. Does not include bearings. (Part No: 9N6303A)
$428.35

Crankshaft Pulley - Crankshaft pulley for Ford 8N, 9N, 2N tractors. Crankshaft mounting is 1.63" O.D. and 1.18" I.D. and has four 1/4" -20 threaded holes for hub when being used with front mounted loader. Can be used with or without loader. Replaces 2N6312. Used with part numbers 192161 and 194354. (Part No: 192160)
$49.29

Crankshaft Pulley - For Ford 8N, 9N, 2N tractors. Supplied with four rubber bushings for hub with 13/32 pins when being used with front mounted loader. (Part No: 192152)
$79.65

Cylinder Head - For 8N, 9N, 2N all GAS 1939-52. Cylinder Head. (Part No: 8N6050A)
$185.96

Cylinder Head Studs - Studs are priced each, must order in quantities of 9. Tractor uses 18. Minimum order is 9. Studs are 7/16 diameter and 3 inches long(threads: coarse 7/16-14 fine 7/16-20). For 8N, 9N, 2N. ** Must order in quantities of 9, priced each. (Part No: 8N6065A)
$4.46

Distributors and Distributor Parts - These are located in the Electrical System parts section. NOTE

Governor - Complete governor assembly, 2 arm, for 8N (1948 through 1952 with proofmeter drive). (Part No: 8N18204B)
$179.33

Governor Ball - Fits 9N, 2N and 8N. 5/8 Inch diameter. 4 used per tractor. Sold individually. Replaces 358081S (Part No: 358081S)
$1.55

Governor Centrifugal Assembly - Governor internal centrifugal assembly, fits 9N18200C or 8N18204B above, for 8N, 9N, 2N (1939 thru 1952). (Part No: 9N8N18179CA)
$154.49

Governor Compensating Spring - 4.95" length. For model 8N. (Part No: 8N9827)
$7.22

Governor Dust Seal - Replacement Governor dust seal. For tractor models 8N, 9N, 2N. (Part No: 9N18183)
$7.39

Governor Housing - Governor Housing includes needle bearing, Lip-type seal, bushing, and proofmeter drive cap with seal and nut. For 8N, 9N, 2N tractors built 1939 thru 1952. (Part No: 8N18085)
$165.37

Governor Lever Spring - This Governor Lever Spring will fit tractor models 9N, 2N, 8N. (Part No: 9N18196)
$4.25

Governor Lower Race Assembly Bearing - For tractor models 8N, 9N, 2N. (Part No: 9N18186B)
$80.61

Governor Mount with Gasket - Aluminum cover used with side mount distributor. (Part No: 8N6017B)
$70.03

Governor Needle Bearing - For tractor models 8N, 9N, 2N. (Part No: 9N18182)
$9.06

Governor Plate - Plate, governor compensating spring anchor plate. For tractor model 8N (1948-1952) (Part No: 8N9855)
$4.92

Governor Repair Kit, Complete - For 9N, 2N and 8N. Kit contains lower race assembly, shaft assembly (with or without proofmeter), upper face assembly, ball bearing assembly, shim, drive shaft ball stop, governor balls (5/8 inch), bushings, mounting gasket, dust seal, C-clip. (Part No: CAPN12502A)
$172.53

Governor Shaft - Shaft assembly, with or without proofmeter. For 8N, 9N, 2N. (Part No: 9N8N18187A)
$54.63

Hand Starting Crank - 8N, 9N, 2N Hand Starting Crank WITHOUT Spinner. Replaces 9N17040 and 2N178040A (Part No: 351010R31)
$28.21

Piston Rings - These are located in the ENGINE RINGS category. NOTE

Pistons and Sleeves - Pistons and Sleeves are located in the "Pistons and Sleeves category" Use your "BACK" key and select this category. (Part No: Various)
$107.00

R Seal Retainer - Retainer, for rear crankshaft oil seal. For tractor models 8N, 9N, 2N. (Part No: 91A6335)
$24.40

Rod with Bushing, Reconditioned - Fits 8N, 9N, 2N all with Gas. Reconditioned Piston Rod with Bushing. (Part No: 1201581)
$117.74

Rotating Valve Conversion Kit - Convert regular exhaust valves to the rotating type. For 8N, 9N, 2N - Kit contains (8) A0NN6500A adjustable tappets, (4) 8N6534B valve rotator kits, (4) 8N6505C exhaust valves, (8) EAM6518A valve locks. Does not include tappet wrenches. (Part No: 8N6546B)
$224.13

Starter Flywheel Ring Gear - Fits all models Ford 1939 thru 1964; except Fordson Major and Dexta. (Part No: 9N6384)
$20.99

Timing Gear Cover - This timing gear cover is for an 8N with Side Mount Distributor. (Part No: 8N6019B)
$78.24

Timing Gear, Camshaft - For Bolt-on type camshafts. Fits 8N, 9N, 2N thru 1952. (Part No: 7RA6256)
$69.90

Timing Gear, Crankshaft - This Crankshaft Timing Gear replaces original part numbers: 48-6306, 48-6306A, 486306A . For tractor models 8N, 9N, 2N. 22 Teeth. (Part No: 486306A)
$39.50

Valve Guide - Single valve guide for 8N, 9N, 2N. ** Order in lots of 8 ** (Part No: 8BA6510B)
$6.11

Valve Guide Retainer - 120 CID 4 cylinder gas engines. Sold in Multiples of 8 only, price shown is for one (Enter 8 or 16 etc. in QTY). For 8N, 9N, 2N. (Part No: 40-6512)
$1.88

Valve Key, Intake & Exhaust - 120 CID 4 cylinder gas engines. NOT for free rotating exhaust valves. For 8N, 9N, 2N. Sold in quantities of 8 only, price shown is for one. (Part No: 7HA6518)
$0.36

Valve Key, Rotating Exhaust - 120 CID 4 cylinder gas engine. Valve key for FREE ROTATING exhaust valves. Sold in quantities of 8 only price shown is for one. For tractor models 8N, 9N, 2N. (Part No: EAM6518A)
$2.59

Valve Seat, Exhaust - These valve seats are the Nickel Series which are made for all new fuel blends. For tractor models 8N, 9N, 2N. (Part No: 218-7405)
$11.55

Valve Seat, Intake - For tractor models 8N, 9N, 2N. (Part No: 218-7535)
$6.30

Valve Service Kit - Contains: 8 Valve Springs, 8 Valve Guides-Solid Type & 16 Valve Locks For 8N, 9N, 2N. (Part No: VSKF928N)
$56.99

Valve Service Kit - For servicing one engine with valve related parts when only valve refacing is required. For 8N, 9N, 2N with solid guides, free rotating exhaust valves. Kit contains valve springs, guides and VALVE ROTATOR KITS. (Part No: VSKF928NFR)
$107.38

Valve Spring - 120 CID 4 cylinder gas engine. Valve spring for use with split guide. For 8N, 9N, 2N. Sold in quantities of 8 only. price shown is for one. (Part No: 2NC6513)
$5.93

Valve Spring Retainer, Intake & Exhaust - 120 CID 4 cylinder gas engines. NOT for free type exhaust valve. Retainer for free type valve not furnished separately, order rotator kit 8N6534B. For 8N, 9N, 2N. ** Must order qty 8, priced each.** (Part No: 8BA6514)
$2.42

Valve Spring Set - Sold in quantities of 8 priced individually. Fits 8N, 9N, 2N. (Part No: 8N6513)
$3.10

Valve Stem Seal - ** Enter in Qtys of 8. ** Seal for valve guide in 120 CID 4 cylinder gas engine. For 8N, 9N, 2N. **Sold in sets of 8, priced each.** (Part No: 8BA6571)
$0.75

Valve Tappet - ADJUSTABLE tappet. Priced EACH. Fits 8N, 9N, 2N. Note: Qty 8 used in engine. (Part No: A0NN6500A)
$14.93

Valve Tappet Wrench Set - For 8N, 9N, 2N. Valve Tappet Wrench (Set of 2). For adjustable tappets. Please Note: The metal wrenches come from the manufacturer with a coat of rust. We have been trying to get them in a better condition without success. They are fully functional and do the job. We will continue our efforts but feel that a useable rusty tool is better than no tool at all. (Part No: 8WR1770)
$15.69

Valve, Exhaust - Exhaust valve using solid guide. Uses 7HA6518 lock. For tractor models 8N, 9N, 2N. (Part No: 8N6505A)
$9.98

Valve, Exhaust, Free-rotating - Exhaust valve for free-rotating type. Uses solid guide & EAM6518A lock. For tractor models 8N, 9N, 2N. (Part No: 8N6505C)
$10.13

Valve, Intake - Intake valve using solid guide. Uses 7HA6518 lock. For 8N, 9N, 2N (Part No: 8BA6507A)
$9.98

Engine Pistons and Sleeves
Cylinder Sleeve, .005 oversize .040 - Oversize replacement for .040 thickness sleeves for larger cylinder block holes. Outside sleeve diameter is 3.273 inches - .005 larger than original. Sleeve is .0425 thickness to retain original piston bore of 3 3/16 inches. For tractor models 8N, 9N, 2N. (Part No: S1135A2)
$41.83

Cylinder Sleeve, .005 oversize .090 - Oversize replacement for .090 thickness sleeves for larger cylinder block holes. Outside sleeve diameter is 3.373, .005 larger than original. Sleeve is .0925 thickness to retain original piston bore of 3 3/16 inches. For 8N, 9N, 2N. (Part No: S1137-2)
$42.86

Cylinder Sleeve, .040 - For tractor models 8N, 9N, 2N. This Sleeve is.040" thin-wall for 3 ring and 4 ring pistons. Priced as each. (Part No: C0NN6055B)
$30.32

Cylinder Sleeve, .050 - Wall sleeve for use with.0825 oversize pistons. For tractor models 8N, 9N, 2N. (Part No: S1138)
$41.88

Cylinder Sleeve, .090 - For tractor models 8N, 9N, 2N. This Sleeve is.090 Heavy-wall for 3 ring and 4 ring pistons. Priced as each. (Part No: 8N6055B)
$25.24

Piston Pin Bushing - For tractor models 8N, 9N, 2N. This piston pin bushing is .735" I.D.. Price shown is EACH, minimum order QTY is 4. (Part No: 21A6207A3)
$4.50

Piston and Sleeve Kit, 3 Ring, .040 Sleeves - Kit contains C0NN6055B .040" sleeves, 8N6108B 3 ring pistons, chrome top & oil rail (8N6149G1) rings, pins & retainers. For tractor models 8N, 9N, 2N. (Part No: APN6055E)
$175.89

Piston and Sleeve Kit, 3 Ring, .090 Sleeves - Kit, (4) sleeves, pistons, chrome rings, piston pins and pin retainers. For 8N, 9N, 2N (Part No: APN6055A)
$191.82

Piston and Sleeve Set - Super Piston Set For 8N, 9N, 2N Increased horsepower up to 5% by use of.0825 wall sleeve, same outside diameter as heavy wall sleeve. Can be used in any application where.090 wall thickness sleeves are used..050 wall sleeves, .0825 oversize 4-ring pistons. Comes with Sleeves, Pistons, Rings and Retainers. (Part No: PK11)
$243.82

Piston, 3 Ring - For tractor models 8N, 9N, 2N. This is a single 3 ring piston with standard bore can be used with .040 thin wall sleeves or .090 thick wall sleeves, and a 3/16 oil ring. (Part No: 8N6108B)
$17.09

Piston, 4 Ring, With 3/16 Oil Ring - For tractor models 8N, 9N, 2N. This is a single piston with a standard bore, 3/16 oil ring. Piston comes with Pin and Lock. This Price is for STANDARD. OVERSIZE ARE AVAILABLE, Please Specify size of std, .020, .030, .040, or .0825 in Comments Boxwhen ordering. (Part No: P1003)
$37.86

Piston, 4 Ring, With 5/32 Oil Ring - For tractor models 8N, 9N, 2N. This is a single piston with 5/32 oil ring, standard bore. (Part No: 2N61084RS)
$37.11

Sleeve and Piston Set - 1 Hole - 3 Ring Piston - .040 Sleeve. Contains Sleeve, Piston, Piston Rings, Piston Pin and Pin Retainer. For 8N, 9N, 2N. (Part No: SAT3A)
$46.13

Sleeve and Piston Set - 1 Hole - 4 Ring Piston - .040 Sleeve. Contains Sleeve, Piston, Piston Rings, Piston Pin and Pin Retainer. For 8N, 9N, 2N. (Part No: SAT2A)
$51.49

Sleeve and Piston Set - 1 Hole - 4 Ring Piston - .090 Sleeve. Contains Sleeve, Piston, Piston Rings, Piston Pin and Pin Retainer. For 8N, 9N, 2N. (Part No: SAT5A)
$51.49

Sleeve and Piston Set, 1 Hole - 3 Ring Piston - .090 Sleeve. Contains Sleeve, Piston, Piston Rings, Piston Pin and Pin Retainer. For 8N, 9N, 2N. (Part No: SAT6A)
$48.97

Engine Rings
3 Ring Piston Ring Set with Chrome Top Ring - For tractor models 8N, 9N, 2N. 1939-1952 4 cylinder gas Standard Bore, CHROME top ring, 2@3/32 comp, 1@3/16 oil. Complete set for one engine. (Part No: 8N6149G1)
$34.95

Piston Ring Set, .0825 Oversize - Plain top ring, 3/16" steel rail oil. For 8N, 9N, 2N. Complete for 1 engine, 4 cylinders. (Part No: PR1003-0)
$67.51

Piston Ring Set, 3 Ring - For tractor models 8N, 9N, 2N. 1939-1952 4 cylinder gas Standard 3 Ring, CHROME top ring, 5/32 steel rail oil. Complete set for one engine. (Part No: 9N6149A)
$43.63

Piston Ring Set, 3 Ring, Plain - For 8N, 9N, 2N. 1939-1952 4 cylinder gas Standard, Plain top ring, 3/16" steel rail oil. Complete set for one engine. (Part No: 8N6149A5)
$31.99

Piston Ring Set, 3 ring - For tractor models 8N, 9N, 2N. Ring set for 3 ring piston with standard bore. This is a SINGLE piston ring set with 3/16 oil ring. (Part No: RST6G1)
$9.10

Piston Ring Set, 4 Ring - Chrome .030" O.S., 3/16" steel rail oil. For 8N, 9N, 2N. Complete for 1 engine, 4 cylinders. (Part No: PR1003-030)
$66.36

Piston Ring Set, 4 Ring - Chrome .040" O.S., 3/16" steel rail oil. For 8N, 9N, 2N. Complete for 1 engine, 4 cylinders. (Part No: PR1003-040)
$66.35

Piston Ring Set, 4 Ring - Chrome.020 O.S., 3/16 steel rail oil. For 8N, 9N, 2N. Complete for 1 engine, 4 cylinders. (Part No: PR1003-020)
$66.35

Piston Ring Set, 4 Ring - For tractor models 8N, 9N, 2N. 1939-1952 4 cylinder gas Standard Bore, Cast Iron rings, 2@3/32 comp, 2@5/32 oil. COMPLETE SET FOR 1 ENGINE. (Part No: 2N6149-4RS)
$55.16

Piston Ring Set, 4 Ring - Chrome. For Ford 8N, 9N, 2N tractors (1939-1952 with 4-cyl. flat head engines) For 4-ring center pin pistons. Std. top rings, 5/32" steel rail oil. COMPLETE SET FOR 1 ENGINE. (Part No: 2N6149G1)
$65.40

Piston Ring Set, 4 Ring - For tractor models 8N, 9N, 2N tractors (1939-1952 w-4-cyl. flat head engines) For 4-ring pistons. Std., plain top rings, 3-16 steel rail oil. Also available in.020, .030, and.040 oversize w- chrome top, 3-16 steel rail oil. Please specify size desired when ordering. Complete for 1 engine, 4 cylinders. (Part No: PR1003)
$72.81

Exhaust System
Clamp - Bracket, rear muffler. EXACT reproduction of ORIGINALrear muffler bracket. For tractors: 8N, 9N, 2N {1939-1952}. (Part No: 9N5260)
$28.53

Exhaust Manifold Gasket - SINGLE gasket (TWO gaskets required) for exhaust manifold on 8N, 9N, 2N. (Part No: 9N9448)
$0.98

Extension Pipe - Vertical two-piece exhaust pipe with clamp, less muffler. For use without muffler, straight through design for maximum exhaust flow-more power. Vertical height remains the same as assemblies with muffler. Inlet 1-1/2" I.D.Outlet 1-1/2" O.D. For 8N, 9N, 2N (Part No: M104)
$26.38

Manifold - High Quality Intake and Exhaust Manifold with Gaskets. For 8N, 9N, 2N (Part No: 9N9425WG)
$61.62

Manifold Nut & Washer Kit - Brass nut & washer kit (Kit contains 4 nuts & 4 Washers) for intake & exhaust manifold. For tractors: 8N, 9N, 2N {1939-1952}. Replaces: Nut (7/16 - 20): 33816S, 7/16 LOCK WASHER: 34808S (Part No: 33816-KIT)
$5.40

Muffler - Heavy-duty horizontal muffler only. Inlet 1-1/2" I.D., outlet 1-1/2" O.D., body length 23". For 8N, 9N, 2N. Does not come with hardware. (Part No: M1002)
$26.61

Muffler - Vertical two-piece, muffler and pipe with clamp. Custom design ready for assembly. Pipe inlet flared, outlet 1-1/2" O.D. For 8N, 9N, 2N (Part No: M102)
$41.12

Muffler Clamp - Flanged Muffler Clamp. For tractor models 8N, 9N, 2N. (Part No: FP185)
$4.49

Muffler and Pipe Assembly - Horizontal muffler & pipe, one piece welded assembly for 8N, 9N, 2N with under-hood exhaust. (Part No: 8N5230)
$26.98

Muffler and Pipe Assembly - Vertical one-piece muffler and pipe assembly, custom design. For 8N, 9N, 2N. Pipe inlet flared, outlet 1-1/2 O.D. (Part No: M200)
$36.02

Stainless Steel Exhaust Pipe - Horizontal, free flow exhaust, fits the same as original but there is NO Muffler. It simply has the appearance of a muffler. For tractor models 8N, 9N, 2N. (Part No: R4883)
$208.37

Fuel System / Air Intake
Air Cleaner Assembly - Fits 9N, 8N. Restoration Quality Air cleaner Assembly, Painted Red. Includes Air cleaner, & cup (with mesh). Will not accurately replace the style with the top wire mesh without modification. This Assembly has a solid cap with hole which can be cut off and replaced with a similar screen and lid or left as is, depending on the needs of the user. (Part No: 8N9600B)
$83.57

Air Cleaner Clip - Clips are for air cleaner 8N9600B. Not exactly like original, works the same. (Part No: 9N9678)
$4.65

Air Cleaner Cup Gasket - For air cleaners with thumb screw clamp (15-1/4" long). Tractors: 8N, 9N, 2N, (1939-1952). (Part No: 9N9623A)
$5.46

Air Cleaner Cup Gasket - For air cleaners with toggle clamps on side of air cleaner (14-3/4long).Use with Air Cleaner Cup S.61648 and S.60583. For tractor models 8N, 9N, 2N, NAA, Jubilee, 600, 700, 800, 900. (Part No: 9N9623B)
$4.65

Air Cleaner Filler - Fits many air cleaners that use steel wool type filler. Custom manufactured mesh. 1 bag = 3-1/2" x 3-1/4". (Part No: S.43231)
$9.90

Air Cleaner Hose Clamp - Clamp, air cleaner to carburetor pipe. Tractors: 8N, 9N, 2N, NAA (1939-1954). For 2 inch O.D. hoses +/- 1/8. (Part No: 9N9653)
$4.46

Air Cleaner Screen - Air cleaner screen. For tractors: 8N (1948-1952). (Part No: 8N9669)
$21.62

Air Cleaner Tube - For tractor models 8N, 9N, 2N. Air Cleaner Tube, Air Cleaner to Carburetor. (Part No: 9N18215C)
$17.29

Air Funnel Assembly - Fits on model 8N. Comes Primed, ready to Paint. (Part No: 8N9684)
$12.88

Air Hose to Carburetor - 1.5 Inches - For 8N, 9N, 2N, NAA, Jubilee, 600, 700, 800, 900 1939-57 gas tractors. Rubber Air Hose is 2 3/8 inches long, 1 1/2 inch inside diameter. (Part No: 9N9652)
$1.69

Cap With Breather - Oil Breather cap with element. For 2000, 2N, 4000, 501, 600, 601, 700, 701, 800, 801, 8N, 900, 901, 9N, NAA, Jubilee. (Part No: 310030)
$9.29

Carburetor Elbow & Strainer - For tractor models 8N, 9N, 2N, NAA, NAB, Jubilee. (Part No: 9N9553)
$3.75

Carburetor Float - This carburetor float is used for the following tractor models: 8N, 900, NAA, and Jubilee all using Zenith carburetor models: 10850, 13876, 13877, 12493, and 13879. (Part No: CTP28)
$16.50

Carburetor Float, Small Bowl - Small bowl carburetor Float for Marvel Schebler carbs (2 3/8 inches at widest point of outside edge of floats) used on 9N, 2N and 8N tractors AND used only on the following engines (yr): 134 CID (1953-1954) or 172 CID(1955-1957) gas engines on tractors: NAA, Jubilee, 501, 600, 620, 630, 640, 650, 660, 601, 611, 621, 631, 641, 651, 661, 671, 681, 700, 740, 750, 701, 741, 771, 800, 820, 840, 801, 811, 821, 841, 851, 861, 871, 881, 900, 950, 960, 901, 941, 951, 961, 971, 981, 2000. (Part No: 9N9550A)
$8.09

Carburetor Gasket Set - For tractor models 8N, 9N, 2N. (Part No: 9N9502)
$2.47

Carburetor Kit, Basic - For Zenith 13876 carburetor on 8N, 9N, 2N. (Part No: BK44V)
$27.48

Carburetor Kit, Basic - For TSX33, TSX241A, TSX241B and TSX241C carburetors on 2N, 8N and 9N tractors. Contains float valve, float lever pin, and gaskets for minor carburetor overhaul. (Part No: BK45V)
$11.93

Carburetor Kit, Comprehensive - For tractor models from 1939 to 1952, carburetor part #: Marvel-Schebler TSX33, Ford 9N9510A. Kit contains all parts necessary for major carburetor overhaul, including a Viton float valve. For 8N, 9N, 2N. Does NOT include float. (Part No: C545V)
$31.45

Carburetor Kit, Comprehensive - For tractor models from 1939 to 1952, carburetor part #: Marvel-Schebler TSX241A, TSX241B, & TSX241C, Ford 8N9510C. Kit contains parts necessary for major carburetor overhaul, including a Viton float valve. For 8N, 9N, 2N. Does Not include Float. (Part No: C546V)
$26.62

Carburetor Throttle Shaft & Lever - For Marvel Schebler carburetor on 8N, 9N, 2N. (Part No: 9N9581A)
$5.94

Carburetor Venturi - Venturi for original Marvel Carburetors. For tractor models 8N, 9N, 2N. Carb Mfg #s - : TSX101, TSX126, TSX133, TSX137, TSX144, TSX151, TSX155, TSX161, TSX171, TSX179, TSX197, TSX211, TSX241A, TSX241B, TSX241C, TSX246, TSX258, TSX290, TSX297, TSX301, TSX33, TSX341, TSX37, TSX38, TSX407, TSX420, TSX423, TSX44, TSX447, TSX453, TSX481, TSX516, TSX55, TSX69, TSX732, TSX748, TSX76, TSX787, TSX79, TSX80, TSX818, TSX827, TSX83, TSX94, TSXU829, TSXU832 (Part No: C5NN9586B)
$9.66

Carburetor, New - With reversible linkage. This Zenith carburetor outperforms the original carbs used on: 8N, 9N, 2N, 1939-1952. New Zenith carb replaces TSX33, TSX241B, TSX241A, TSX241C and OEM# 8N9510C. Center to center on the 2 mounting bolts is 2 1/4 inches. Made in USA, 1 year warranty. (Part No: 13876)
$247.00

Carburetor, New - For 8N, 9N, 2N, ALL 1939-1952 - Original Marvel-Schebler design replaces TSX33, TSX341B, TSX431C. (Part No: 8N9510C)
$109.60

Carburetor, Rebuilt - This Rebuilt Zenith carburetor outperforms the original carbs used on: 8N, 9N, 2N, 1939-1952. This Zenith carb replaces TSX33, TSX241B, TSX241A, TSX241C and OEM# 8N9510C. Center to center on the 2 mounting bolts is 2 1/4 inches. Made in USA. There will be an additional core charge of $50 added to your order this is refundable if you send your core to us. (Part No: 13876R)
$157.71

Carburetor, Rebuilt - This rebuilt carburetor replaces the original Marvel-Schebler design and fits the following tractor models: 8N, 9N, and 2N. It is being used as a direct replacement for Carburetors with the numbers matching: TSX33 and TSX241B. There will be an additional core charge of $50 this is refundable if you send your core to us. (Part No: 1302-CARB)
$154.62

Choke Control Rod Assembly - Pre-bent Choke Control Rod is 29 1/2 inches long. Does NOT come with knob. For tractors: 8N, 9N, 2N (1939-1952). See part number 9N9815 for Throttle to Governor Rod. (Part No: 9N9700)
$31.00

Choke Fly Assembly - Choke fly assy. 1-5/16 dia. For 2N, 600, 700, 8N, 9N, NAA, Jubilee. (Part No: 9N9549)
$19.61

Choke Knob - For tractors: 8N, 9N, 2N (Part No: 9N9703)
$4.50

Choke Lever & Shaft - For tractor models 8N, 9N, 2N. (Part No: 9N9546)
$6.68

Choke Retainer Spring - Package of two. Used on original Marvel Schebler TSX33, TSX241A, TSX241B, & TSX241C (Part No: 9N9539)
$3.00

Cyclone Air Cleaner Glass Jar - For 8N, 9N, 2N, NAA, Jubilee, 600, 700, 800, 900, 601, 701, 801, 901, 2000, 4000, all 1939 to 1964. Cylone Air Cleaner Glass Jar (Jar Only) Screw on type. Exactly Like Original for tractors that used the "Cyclone" Air Cleaner only. (Part No: 230056)
$31.65

Cyclone Air Cleaner Rubber Seal - Rubber Seal, For CYCLONE Air cleaner only. Exact of original. Minimum order Qty is 2. (Part No: 230055)
$10.76

Cyclone Cup and Spring Assembly - Only for those tractors (1939-1964)that used the CYCLONE air cleaner assy which MAY include: 8N, 9N, 2N, NAA, Jubilee, 600, 620, 630, 640, 650, 660, 601, 611, 621, 631, 641, 651, 661, 671, 681, 700, 740, 750, 701, 741, 771, 800, 820, 840, 801, 811, 821, 841, 851, 861, 871, 881, 900, 950, 960, 901, 941, 951, 961, 971, 981, 2000, 4000. Verifiy the type of air cleaner you have before ordering. (Part No: 230053)
$22.96

Fuel Cap - Original style cap fits 8N, 9N, 2N. Fuel cap for self venting tanks. Cap is non-vented. (Part No: 9N9030Z)
$6.30

Fuel Cap - For 8N, 9N, 2N, 600, 620, 630, 640, 650, 660, 800, 820, 840, NAA Fuel Cap. This is a non-vented cap. (Part No: D5NN9030A)
$5.99

Fuel Cap, Vented - 2-5/8" O.D, chrome Finish, 1-3/4" edge of tang to edge of tang, vented, includes gasket. For tractor models 8N, 9N, 2N, Jubilee, Golden Jubilee, NAA, NAB, 501, 541, 600, 601, 611, 620, 621, 630, 631, 640, 641, 650, 651, 660, 661, 671, 681, 700, 701, 740, 741, 771, 800, 801, 811, 820, 821, 840, 841, 850, 851, 860, 861, 871, 881, 900, 901, 941, 950, 951, 960, 961, 971, 981, 1801, 1811, 1821, 1841, 1871, 1881, 2000, 2030, 2031, 2100, 2110. (Part No: C5NN9030D)
$7.50

Fuel Line - For tractor models 8N, 9N, 2N, (1939-1952). This fuel line is from sediment bowl to carburetor. Consists of: 1/4 inch steel tubing with two 1/4 inch inverted flair fittings installed. (Part No: 9N9282A)
$18.38

Fuel Line Anti-Rattler - For 8N, 9N, 2N 1939-1952. Fuel Line Anti-Rattler between fuel line and tank. Restoration Quality. (Part No: 9N9121A)
$5.25

Fuel Sediment Bowl Assembly - For models 8N, 9N, 2N, NAA and Jubilee with SHORT BOWL. The fuel bowl assembly has a 7/16 inch 24 thread fuel line inlet and works with 9N9282A fuel line. Replaces 2N99155B and NAA9155B with short bowl. (Part No: 2NAA9155B)
$11.48

Fuel Sediment Bowl Bail assembly - For tractors 8N, 9N, 2N, NAA, Jubilee. (Part No: 2N9166)
$1.64

Fuel Sediment Bowl GASKET - Gasket, sediment bowl. 2" O.D. Tractors: 8N, 9N, 2N (1939-1952), NAA, 600, 700, 800, 900 (1953-1957). (Part No: NAA9160A)
$0.29

Fuel Sediment Glass Bowl With Gasket - 2" Glass Bowl/W gasket fits NAA9155B and 2N9155B sediment bowls. Includes gasket. Fits 8N, 9N, 2N, NAA, Jubilee. (Part No: 9N9162)
$2.07

Fuel Sediment Screen and Gasket - Gasket & Screen Set (for 2"OD Sediment Bowl), Ford 8N, 9N, 2N, 600, 601, 620, 630, 640, 650, 660, 700, 740, 750, 800, 801, 820, 840, 900, 950, 960. (Part No: 2NAA916061)
$1.32

Gasoline Fuel Tank, Steel - Gasoline Fuel Tank (Steel) For 8N, 9N, 2N. (Part No: 9N9002)
$142.40

Governor Compensator Spring Assembly - 3 Pieces. Replaces NCA99810A. For Jubilee, NAA thru 960 1953-1958 4 cylinder gas. For 501 thru 4140 4 cylinder gas and LP 1958-64 with engine SN# 26402 and up (Part No: NCA99810A)
$13.43

Harco 1/2 Pint Jar - 1/2 pint jar for Harco Air cleaner (side mount) on 8N. (Part No: ACP2131)
$3.21

Harco Air Cleaner - For 8N (1948-1952) Harco style side mount air cleaner assy with jar and clamp, mounts over air door hole in hood (side mount). (Part No: AC2H18N)
$258.16

Harco Pint Jar - 1 pint jar for Harco Air cleaner (side mount) on 8N. (Part No: ACP1237)
$16.82

Harco Spring and Bail Assembly For 1/2 Pint Jar - Fits Harco 1/2 pint jar. Spring and bail assembly for Harco air cleaner (side mount)on 8N. (Jar NOT included). (Part No: ACP2133)
$48.30

Harco Spring and Bail Assembly for 1 Pint Jar - 1 pint jar spring and bail assembly for Harco air cleaner (side mount) on 8N. (Jar NOT included). (Part No: ACP2134)
$29.58

Main Adjustable Needle - Main adjusting needle. For tractor models 8N, 9N, 2N. (Part No: 9N9565C)
$4.37

Needle Valve - Viton float valve needle, seat & gasket assembly. Tractors: 8N, 9N, 2N, (1939 to 1952). (Part No: C3NN9564A)
$3.69

Nozzle - Main nozzle. For tractor models 8N, 9N, 2N. For Marvel-Schebler TSX241A, TSX241B, & TSX241C, TSX33, Ford 8N9510C, Ford 9N9510A. (Part No: 9N9530)
$11.91

Quad Throttle Plate - For 8N. Quad Throttle Plate. (Part No: 8N9889A)
$9.98

Race Assembly - Upper race assembly. For 8N, 9N, 2N (Part No: 9N18188B)
$41.43

Sediment Bowl Valve Stem - Sediment Bowl Valve Stem with wheel complete. For tractor models 8N, 9N, 2N, NAA. (Part No: APN9194)
$3.44

Throttle Control Lever Assembly - For model 8N. (Part No: 8N9805)
$36.08

Throttle Control Rod Spring - For model 8N 1948-1952. (Part No: 8N9806)
$5.67

Throttle Friction Disc - This throttle friction disc is 3 inches in diameter and has a 1/2 inch center hole. It fits the following tractor models: 9N, 2N, and 8N. Replaces part number C5NN518B. (Part No: C5NN518B)
$1.17

Throttle Rod - This governor to carburetor control rod assembly is 7 inches long and has a ball recepticle on both ends. For tractors: 8N, 9N, 2N (1939-1952). (Part No: 9N9818A)
$20.82

Throttle Rod - Rod, throttle to governor control rod assembly. Rod is approximately 23" long and has adjustable length. Spring loaded "bullet" type ends for coupling to linkage. For tractors: 8N (1948-1952) (Part No: 8N9815)
$36.39

Gauges
Ammeter - For all models to 1958. Terminal type Ammeter. 30 - 30. Chrome Ring. Replaces FAD10850A. (Part No: A0NN10670A)
$5.99

Gauge Kit, 8N - 8N Gauge Kit - (For 8N after SN# 263844) Consists of Proofmeter, 50 lb. Oil Gauge, and 30-30 Ammeter. (Part No: 8NGAUGEKIT)
$58.17

Instrument Panel Light Assembly - 6 Volt Light Assembly. For Model: 8N. (Part No: 8NN14662A)
$28.11

Oil Pressure Gauge - For tractor models 8N, 9N, 2N, 600, 700, 800, 2000, 4000, NAA, Jubilee. all before 1964. Oil Pressure Gauge, 40 lbs., 2" Body Diameter. Replaces OEM numbers Ford: FAD9273A and Massey Ferguson:506902M92. (Part No: S.61171)
$12.72

Oil Pressure Gauge, 50lb - For tractor models 8N, 9N, 2N. Oil Pressure Gauge, 50 lbs., 2" Body Diameter. (Part No: 9N9273A)
$11.76

Oil Pressure Gauge, 50lb Black - For tractor models 8N, 9N, 2N. Oil Pressure Gauge, 0-50 lbs., for 2 inch Diameter hole. (Part No: 9N9273A-BLACK)
$10.75

Oil Pressure Gauge, 80LB, Black - For tractor models 8N, 9N, 2N, 541, 600, 620, 630, 640, 650, 660, 601, 611, 621, 631, 641, 651, 661, 671, 681, 700, 740, 750, 701, 741, 771, 800, 820, 840, 801, 811, 821, 841, 851, 861, 871, 881, 900, 950, 960, 901, 941, 951, 961, 971, 981, (2000, 4000 4 cylinder), NAA, Jubilee, 1801. Black raised bezel, measures to 80 LB, dash or bracket mounted gauge with a bracket and studs 1/8" NPT thread. Repalces FAD9273A. (Part No: FAD9273A_Black)
$10.41

Proofmeter - Proofmeter for 8N (1950 to 1952) Proofmeter assembly, MPH. (Part No: 8N17360A1)
$21.75

Proofmeter Cable - Fits 8N with side mount distributor (1950-1952) 34 Inches Overall Length. (Part No: 8N17365)
$11.98

Proofmeter Cable - Steel - For 8N 1950 to 1952. Proofmeter Cable is Exactly Like Original, Metal Case, 34 inches Overall Length. (Part No: 8N17365B-STEEL)
$11.83

Screw Kit - Screw kit, 3 per pkg. Screw kit, throttle plate to instrument panel, set of 3. Tractors: 8N (1948-1952). (Part No: 28319-KIT)
$1.95

Temperature Gauge Adapter Pipe - 3 5/8" Long, 1 1/2" O.D; Uses 5/8" -18 UNF Temperature Gauge Lead. Installs in upper hose. Cut hose, slide new adapter pipe in place, drill 2" O.D. hole in dash to mount gauge. For tractor models: 2N, 8N, 9N. (Part No: FDS2673)
$48.30

Temperature Gauge Kit - Use to install temperature gauge in tractors that did not originally come with temp gauge. Kit includes original style hose clamps, temp gauge adapter pipe and temperature gauge. Installs in upper hose. Cut hose, slide new adapter pipe in place, drill 2" O.D. hole in dash to mount gauge. For tractor models: 2N, 8N, 9N. The temperature gauge is a complete assembly with bracket and adapters. Dial calibrated to 280 degrees, extra long 70" capillary line. (Part No: FDTEMP)
$85.55

Hitch / Drawbar
Chain - CHAIN, Fixed drawbar safety chain assy, EXACT reproduction of ORIGINAL drawbar chain. FOR tractors: 8N, 9N, 2N, Jubilee, NAA (1939-1954). (Part No: 9N5370)
$91.02

Crank Arm, Leveling Box - This Leveling Box Crank Arm is for tractor models 2000, 2100, 2600, 2610, 2N, 3000, 3100, 340, 3400, 3550, 3600, 3610, 4000, 4110, 420, 4600, 600, 700, 800, 8N, 900, 9N, NAA. (Part No: C5NN594E)
$7.53

Drawbar Link Check Chain Anchor - Anchor, Drawbar link check chain (pair- one right and one left). For 2000, 2600, 2610, 2N, 3000, 3600, 3610, 4000, 4600, 4610, 600, 700, 800, 8N, 900, 9N, Dexta, NAA, Super Dexta, Jubilee. (Part No: 957E5967)
$15.33

Eyelet Assembly, Check Chain - This Check Chain Eyelet Assembly fits 9N, 8N, NAA, Jubilee, 900, (2000 4-cyl RowCrop 1/1953 & newer), (4000 RowCrop 1/1953 & newer). (Part No: EC0N660A)
$4.67

HITCH BALL 10000LB 2-5/16 - 2-5/16 BALL SIZE, 1-1/4STUD THREAD, 2-1/2 STUD LENGTH, 10000 LB MAX LOAD CAPACIRY, THREE CHROME HITCH BALL CLASS. (Part No: CHB2516114)
$23.85

HITCH BALL 15000LB 2-5/16 - 2-5/16 BALL SIZE, 1-3/8STUD THREAD, 2-5/8 STUD LENGTH, 15000 LB MAX LOAD CAPACITY, THREE CHROME HITCH BALL CLASS. (Part No: CHB2516138_)
$25.04

HITCH BALL 2000LB - 1-7/8 BALL SIZE, 3/4 STUD THREAD, 1-3/4 STUD LENGTH, 2000 LB MAX LOAD CAPACIRY, ONE CHROME HITCH BALL CLASS. (Part No: CHB17834)
$9.23

HITCH BALL 3500LB - Hitch ball. 2" ball size, 3/4" stud thread, 1-7/8" stud length, 3500 lb. max load capacity, one/two chrome hitch ball class. (Part No: CHB234)
$9.48

HITCH BALL 5000LB - Hitch ball. 2" ball size, 1" stud thread, 2-1/8" stud length, 5000 lb. max load capacity, two chrome hitch ball class. (Part No: CHB21)
$10.83

HITCH BALL 5000LB 2-5/16 - Hitch Ball, 2-5/16" ball size, 1" stud thread, 2" stud length, 5000 lb. max load capacity, three chrome hitch ball class. (Part No: CHB25161)
$15.39

Level Box Fork - Right - Fork, hydraulic lift leveling rod, Right Hand. Length 10-1/4". For 8N, 9N, 2N, Jubilee, NAA. (Part No: 9N585A)
$26.98

Level Box Handle - Lever handle. For 2000, 2N, 4000, 501, 600, 700, 800, 8N, 900, 9N, Jubilee, NAA (Part No: 9N594)
$8.19

Leveling Box - Economy - For tractor models 8N, 9N, 2N, NAA, Jubilee, Dexta, Super Dexta. Working length of 19.5 to 27 inches. Pin holes are 3/4 inch. (Part No: ECON577AB)
$22.42

Leveling Box Assembly, Left - Left Hand Rod and fork assembly, hydraulic lift, left hand. For 8N, 9N, 2N, NAA, Jubilee, tractors. 1939 - 1954. 18 to 22 Inches Center to Center adjustablility. (Part No: 8N564B)
$46.86

Leveling Box Assembly, Right - This Right Hand Leveling Box Assembly uses 5/8 inch pins and opens center-to-center from 17.75 to 21.5 inches. Adjusts 21.5 inches. For 8N, 9N, 2N, NAA, Jubilee. (Part No: 8N577A)
$54.51

Leveling Box Gear - Gear, leveling box pinion. For 2000, 2N, 3000, 4000, 501, 600, 700, 800, 8N, 900, 9N, Jubilee, NAA (Part No: B9NN568A)
$8.43

Leveling Box Knuckle Pin - MUST ORDER IN QTY 2 PRICED EACH. For tractor models NAA, Jubilee, 600, 620, 630, 640, 650, 660, 601, 611, 621, 631, 641, 651, 661, 671, 681, 700, 701, 741, 771, 740, 750, 800, 820, 840, 801, 811, 821, 841, 851, 861, 871, 881, 801, 811, 821, 841, 851, 861, 871, 881, 701, 801, 900, 950, 960, 901, 941, 951, 961, 971, 981, 8N, 9N, 2N all built 1939 to 1964, (2000, 3000, 4000 1965 and up), (3600, 4600 1975 and up). 5/8 Pin Diameter 2 7/8 usable length. Takes our 3/16 Linch pin (P/N DKP316). MUST ORDER IN QTY 2, PRICED EACH. (Part No: 9N595)
$1.59

Leveling Box Knuckle, Right - Knuckle, Right Hand leveling assembly. Pin Holes are 5/8 of an inch. The shape of the one pictured may vary slightly from different manufacturers. For tractor models 2000, 2N, 3000, 3600, 4000, 4600, 501, 600, 700, 800, 8N, 900, 9N, Jubilee, NAA. Uses 2 pins P/N 9N595. (Part No: 957E566)
$7.53

Leveling Box Yoke Rod, LH - Left Hand side. Rod dia is .750". For tractor models 2000, 2100, 2600, 2610, 2N, 3000, 3100, 340, 3400, 3550, 3600, 3610, 4110, 420, 600, 620, 30, 640, 650, 660, 700, 740, 750, 800, 820, 840, 900, 950, 960, 8N, 9N, NAA, Jubilee. (Part No: C5NNB863A)
$28.90

Lift Arm - 32 Inch - Cat 1 - Lower lift arm, heavy-duty, with forged ball-joint ends. Category I accommodates 7/8" drawbar or lower link pins. Painted blue. Length 32". For tractor models 8N, 9N, 2N, Golden Jubilee and NAA (Part No: JSA1002B)
$45.55

Lower Link Support Pin, 5 1/8 Inches - This Lower link support pin measures 5 1/8 inches long. It is for tractors less Differential Lock for models 2000, 3000, 3600, 4000, 4600, 600, 601, 700, 701, 800, 801, 8N, 900, 901, NAA, Jubilee. (Part No: NCA563C)
$14.25

Pin, Hydraulic Lift Yoke - For tractor models 8N, NAA, Jubilee, (1950-1954). (Part No: 8N486B)
$13.12

Shaft Level Box - Shaft and gear, length 14; thread length 4. For 2000, 2N, 4000, 600, 700, 800, 8N, 900, 9N, Dexta, Jubilee, NAA, Super Dexta (Part No: NCA579B)
$13.17

Stabilizer Arm Red - Arm only, red. Length 31-1/2 center to center. For tractor models 2N, 600, 800, 8N, 9N, Jubilee, NAA. (Part No: 230042R)
$10.48

Stabilizer Kit, Extra Heavy Duty - Universal Stabilizer Kit For 8N, 9N, 2N, NAA, Jubilee, 600, 800. Contains (2) stabilizer bars, universal brackets with pins & hardware. 31.5 inches center to center. ** $15 ADDED TO SHIPPING DUE TO WEIGHT ** IF ORDERING ON-LINE, THIS ADDITIONAL CHARGE WILL BE ADDED TO YOUR ORDER AFTER YOUR RECEIPT IS PRINTED. (Part No: 231253XHD)
$58.73

Stay Strap, Lower Red - For 8N, 9N, 2N, NAA, 600, 700, 800, 900. Stay Strap - Lower. (Part No: 9N5375)
$9.54

Stay Strap, Upper Red - For 8N, 9N, 2N, NAA, 600, 700, 800, 900. Stay Strap - Upper. (Part No: 9N5374)
$9.66

Swinging Drawbar - This drawbar is used for the swinging drawbar assembly. 600, 800, 840, 841, 851, 860, 8N, NAA, Jubilee. Drawbar measures 29.375 inches in length, 2 inches wide, 1 inch thick, off-set. (Part No: C0NN805F)
$44.85

Swinging Drawbar Clevis Assembly - Clevis assembly with pins for SDA6 or SDA8 kits. For tractor models 8N, Jubilee, NAA, NAB, 600, 601, 611, 620, 621, 630, 631, 640, 641, 650, 651, 660, 661, 671, 681, 800, 801, 811, 820, 821, 840, 841, 850, 851, 860, 861, 871, 881, 1801, 1811, 1821, 1841, 1871, 1881, 2000 4 cylinder, 2030, 2031, 2120, 2121, 2130, 2131, 4000 4 cylinder, 4030, 4031, 4040, 4120, 4130, 4131, 4140. (Part No: NCA803B)
$31.50

Swinging Drawbar Hanger - Drawbar hanger. For 600, 8N, NAA (Part No: NCA809A)
$41.85

Swinging Drawbar Kit - This Drawbar assembly is for NAA, 600, 8N. Swinging Drawbar Kit. Painted Red. Contains Drawbar: 29.375" long, 2.00" wide, 1.00" thick, Rear Drawbar Hanger, Drawbar Clevis Assembly and Drawbar Clevis Pin. May come painted Red, Black or primer. (Part No: 49A34R)
$121.18

Thrust Bearing - Leveling Box Assembly Bearing. For 2000, 2N, 3000, 3600, 4000, 4600, 501, 600, 700, 800, 8N, 900, 9N, Dexta, Jubilee, NAA, Super Dexta (Part No: 9N554)
$22.80

Hydraulic System
Bushing - Bushing for hydraulic pump base, for PTO shaft. For 8N, 9N, 2N. (Part No: 9N649A)
$19.48

Cam Block - For hydraulic pump, 9N, 2N and 8N (1939-52). (Part No: 9N617A)
$40.42

Chamber Kit - Repair kit for one hydraulic pump chamber. Fits either Left or Right. For 8N, 9N, 2N (Part No: 9N621KIT)
$19.35

Draft Control Plunger - For tractor models 8N, 9N, 2N, NAA, Jubilee, 600, 700, 800, 900, 601, 701, 801, 901, 2000, 4000, Dexta, Super Dexta. (Part No: 8N541B)
$34.95

Draft Control Plunger Spring - This Draft Control Plunger Spring fits between the Hydraulic plunger and yoke. Fits 9N, 2N 8N, NAA, Jubilee, 600, 800, 601, 801, 2000, 4000 (except rowcrop), Dexta, Super Dexta. (Part No: 9N547B)
$34.35

Draft Control Spring Plate, with Pin - For tractor models 8N, NAA (1948-1954). (Part No: 8N527)
$25.11

Draft Control Yoke - Fits 8N, 9N, 2N. (Part No: 9N546C)
$31.11

Felt, Spring Seat - Hydraulic lift draft control spring seat. For tractor models 8N, 9N, 2N, NAA, 600, 601, 700, 701, 800, 801, 900, 901, (1939-1962). (Part No: 9N529)
$3.90

Friction Disk - Hydraulic Control Lever. 3" dia. 1/2" hole. For tractor models 2N, 600, 601, 700, 701, 800, 801, 8N, 900, 901, 9N, NAA, (2000 & 4000 4 cyl.). Price is for each. (Part No: C5NN518B)
$1.17

Gasket, Hydraulic Cylinder to Center Housing - 1" O.D., 7/16" I.D.. For tractor models 8N, 9N, 2N. ** Sold in quantities of 10, priced each. (Part No: 9N552)
$0.52

Gasket, Hydraulic Pump Drain - Fits 8N, 9N, 2N. Sold in lots of 5, Priced each. (Part No: 8N7011)
$.58

Hydraulic Lift Control Quadrant - For tractor models 8N, 9N, 2N. Hydraulic lift control lever connects to this. Also fits NAA, Jubilee, 2000, 4000, 501, 600, 800, 900, 700, all 1939-1964 4 cylinder. Replaces 2N516A, 2n516A2. (Part No: 9N515)
$20.75

Hydraulic Lift Cover Repair Kit - For 8N, 9N, 2N. Lift Cover Repair Gasket Kit. Gasket Set includes 2 Valve chamber gaskets, lift cover gasket, base pump gasket, 2 inspection cover gasket cylinder to center housing cover, 2 hydraulic lift cylinder housing gasket. (Part No: LCRK928)
$7.49

Hydraulic Lift Cylinder - For 8N, 9N, 2N. Hydraulic Lift Cylinder. Cylinder only. Can use 3 ring piston or o-ring type. Sold seperately. (Part No: 9N510D)
$64.17

Hydraulic Lift Level Indicator (Dip Stick) - 8N, 9N, 2N, NAA. Hydraulic Lift Level Indicator. (Part No: NAA927C)
$4.70

Hydraulic Lift Lever - For tractor models 8N, 9N, 2N, NAA, 600, 601, 700, 701, 800, 801, 900, 901, (2000, 4000 4 cyl.). (Part No: S.66598)
$20.02

Hydraulic Lift Piston - This is a single groove Hydralic Lift Piston that measures 2-1/2" diameter, groove is centered 1 1/4 inch from bottom of piston. O-Ring available as NAA533A and Back Up Washer as NAA473A. For tractor models NAA, NAB, 8N, 9N, 2N, Jubilee. (Part No: NAA530B)
$19.65

Hydraulic Lift Piston - 3 ring Piston, hydraulic lift. For 8N, 9N, 2N. Uses 9N675 ring set. (Part No: 9N530B)
$29.88

Hydraulic Lift Piston Connecting Rod - For Dexta, NAA, 2N, 2000, 3000, 4000, 600, 700, 8N, 800, 9N, 900. Replaces NCA526A and 957E526. (Part No: 86563314)
$29.92

Hydraulic Lift Piston O-Ring - For 8N, 9N, 2N. O-Ring used on piston #NAA530B. Price is for each. Used with lift piston washer #NAA473A. NOTE: The leather washer goes on first, then the o-ring. (Part No: NAA533A)
$1.11

Hydraulic Lift Piston Rings - Kit of 3, steel, fits piston 9N530B. For tractor models 8N, 9N, 2N. (Part No: 9N675)
$10.63

Hydraulic Lift Piston Washer - For 9N, 8N, 2N. Hydraulic Lift Piston Washer used with Piston #NAA530B. Price is for each. (Part No: NAA473A)
$2.78

Hydraulic Lift Ram Arm - This Hydraulic Lift Ram Arm fit the 8N, 9N, 2N. This part will work for the 9N, 2N and early 8N but does not look like the original. This does look like the original for the Late 8N. For an early 9N, this part may require additional machining, such as grinding down the end raised portion, and/or shortening one end 1/4 inch and adjusting with shims. (Part No: 8N545B)
$69.77

Hydraulic Lift Shaft Arm - For 8N, 9N, 2N, NAA, Jubilee, 600, 700, 800, 900, 2000, 4000 gas. (Part No: 9N543B)
$62.03

Hydraulic Lift Shaft Bushing - 2 used. I.D. 2.000, O.D. 2-3/8, L. 3.00. For tractor models 8N, 9N, 2N, NAA, 600, 800, 2000, 3000, 4114. (Part No: 9N531C)
$17.52

Hydraulic Lift lever Assembly - For 8N, 9N, 2N, NAA, Jubilee, 600, 700, 800, 900, 601, 701, 801, 901, 2000, 4000 PRIOR TO 1965. Assembly contains: Lift Control Lever with Ball End 2N512, Lift Control Plate (Cast Aluminum as original) 2N-516A2 and Friction Disc C5NN518B. (Part No: 2N512)
$41.52

Hydraulic Pump Drive Shaft - APPLICATION: 8N, 9N, 2N, SHAFT DIAMETER: 3/4 ", SHAFT OVERALL LENGTH: 13-1/16 ", END A TYPE: Key, END A SIZE: 3/4 ", END B TYPE: LH Thread, END B SIZE: 5/8 " . END A mates to coupler L601-14. END B mates to hub 191196. (Part No: 190760)
$16.82

Hydraulic Pump Drive Shaft - For tractor models 8N, 9N, 2N. 3/4 inch shaft diameter, 13 inches in length, 6 spline on one end and key on other end. Mates with end hub 192161 or 54C2055. Other end mates with coupler L601-14. (Part No: 194354)
$24.97

Hydraulic Pump Hub - Hydraulic Pump Hub for Sherman 54 Series Loader. Hydraulic Pump Hub 3 7/8 O.D., 2 3/4 Center to center on holes. 6 spline center bore, 3/4 I.D. (Part No: 54C2055)
$40.11

Hydraulic Pump Hub - For tractor models 8N, 9N, 2N. Hydraulic pump hub is 3" O.D., 2 13/32 center to center on pins (no holes). Includes pins. (Part No: 191196)
$40.00

Hydraulic Pump Hub - This Hydraulic Pump Hub is used on tractor models 8N, 9N, 2N. Verify measurements. Hydraulic Pump Hub is 3 3/8" O.D., 2 3/8 Center to center on holes. 6 spline - center bore = 5/8" on the lands and 3/4" on the grooves. Used with part numbers 192160 and 194354. (Part No: 192161)
$35.10

Hydraulic Pump Overhaul Kit - For 8N, 9N, 2N (1939-52). Kit contains cam blocks, pistons, chamber kits, PTO shaft bushing, safety valve, and gaskets. (Part No: HPOK1)
$158.70

Hydraulic Pump Rebuild Kit, Comprehensive - For tractor models 8N, 9N, 2N (1939-52). Kit contains 2 cam blocks, 2 Pistons, 2 Chamber Repair Kits, PTO Shaft Bushing, Safety Valve, 2 Valve Chambers with Valves, Base Gasket, Sump Pump Gasket, 2 Side Gaskets, PTO Shaft Gasket, 2 Side Plate Gaskets. (Part No: S.61725)
$298.52

Hydraulic Pump Valve Chamber - Left Hand Valve Chamber, less valves. For 8N, 9N, 2N. Polished Steel Finish. (Part No: 9N622)
$141.06

Hydraulic Pump Valve Chamber - Left Hand Valve Chamber, Less Valves. For 8N, 9N, 2N. Cast Iron. (Part No: 9N622-C)
$84.18

Hydraulic Pump Valve Chamber - Right Hand Valve Chamber, Less Valves. For tractor models 9N, 8N, 2N. Cast Iron (Part No: 9N621-C)
$108.81

Hydraulic Pump Valve Chamber - Right Hand Valve Chamber, less valves. For 8N, 9N, 2N. Polished Steel Finish. (Part No: 9N621)
$97.29

Hydraulic Pump Valve Chamber Assembly, LH - Left hand valve chamber with valves. For tractor models 8N, 9N, 2N. Cast Iron. (Part No: 9N622-ASSY)
$82.73

Hydraulic Pump Valve Chamber Assembly, RH - Right hand valve Chamber with valves. For tractor models 9N, 8N, 2N. (Part No: 9N621-ASSY)
$82.73

Hydraulic Pump, New - For tractor models 8N. (Part No: 8N605A)
$603.75

Hydraulic Safety Valve Assembly - For tractor models 8N, 9N, 2N. (Part No: 8N638)
$20.33

Hydraulic Spring Seat - For tractor models 8N, 9N, 2N, NAA, 600, 900 (1948-1954). (Part No: 9N525B)
$12.93

Hydraulic pump base to center housing Gasket - For tractor models 8N, 9N, 2N. (Part No: 9N611)
$1.77

Lift Cylinder Housing Gasket - For tractor models 8N, 9N, 2N. (Part No: 9N553)
$0.68

Lock Washer, Assembly - Lock Washer Assembly for hydraulic lift shaft to arm. For tractor models 9N, 8N, NAA (1939-1954). (Part No: 9N550)
$6.09

Piston for Hydraulic Pump - For 8N, 9N, 2N (1939-52). (Part No: 9N615)
$24.43

Quadrant Stop Kit - For tractor models 2000 4 cylinder, 2N, 4000 4 Cylinder, 8N, 9N, Jubilee, NAA, NAB, 501, 541, 600, 601, 611, 620, 621, 630, 631, 640, 641, 650, 651, 660, 661, 671, 681, 700, 701, 740, 741, 771, 800, 801, 811, 820, 821, 840, 841, 850, 851, 860, 861, 871, 881, 900, 901, 941, 950, 951, 960, 961, 971, 981, 1801, 1811, 1821, 1841, 1871, 1881, 2030, 2031 all with 4 cylinder from 1939 - 1964. (Part No: 9N521)
$6.09

Seat, Hydraulic Lift Draft Control Spring - Exact of original. Fits all models (1939-1964). (Part No: 2N624)
$9.07

Universal Pressure Gauge, Hydraulic - 400 lb Gauge. Glycerin Filled. Stainless Steel Case 2-1 2 diameter. Nickel silver movement accurate to within 2%. Dual range KPA-PSI. Plexiglas crystal. 1 4 NPT male brass fitting. (Part No: GG400)
$11.13

Valve chamber to base Gasket - For tractor models 8N, 9N, 2N (1939-1942). (Part No: 9N613)
$0.73

Implements
Bush Hog Axle Spacer Bushing - Used on the following Bush Hog cutters: 12, 104, 105, 109, 126, 205, 255, 275, 285, 305, 306, 307, 405, 405HR, 406, 406HR, 502, 600, 1050, 1051, 1109, 1126, 1207, 1209, 1226, 1306, 1307, 1405, 1406, 2510, 2512, 3108, 2309, BD90, FH162, S268, SM60, SQ36, SQ480, SQ600.Wheel must be attached to fork. For Bush Hog cutters. With SPB40 spacer, assembly will also replace all models with Timken bearings (Ref #1-#11). (Part No: SPB40)
$4.91

Caster Assembly, Old Style - Tail wheel & hub assembly with grease fitting. 4 x 8 inch rim, 15 inch O.D. of wheel. Includes Wheel, Hub, Axle Bearing, and Bolt Assembly.OLD style tail assembly used on the following Bush Hog cutters: 12, 104, 105, 109, 126, 205, 255, 275, 285, 305, 306, 307, 405, 405HR, 406, 406HR, 502, 600, 1050, 1051, 1109, 1126, 1207, 1209, 1226, 1306, 1307, 1405, 1406, 2510, 2512, 3108, 2309, BD90, FH162, S268, SM60, SQ36, SQ480, SQ600.Wheel must be attached to fork. For Bush Hog cutters. With SPB40 spacer, assembly will also replace all models with Timken bearings (Ref #1-#11). (Part No: BH215)
$107.75

Hub Assembly - Hub with bushings (3/4"), wheel bolts (4), and grease fitting. Center tube length 5". For rotary cutters: RB60 with new style 1-1/4" dia. caster, SM60R, SM160R; Squealer models: 1207, SQ36, SQ48, SQ60, SQ72, SQ148, SQ480. Replaces 60978, 60990, 63812. Can use 500BH tail wheel. (Part No: 63813BH)
$22.74

Tail Wheel Assembly - 6" x 9" tail wheel assembly with laminated tire, less hub. 4" pilot, 5 bolt holes, 5-1/2" bolt circle. 5-1/4" wide, 21" O.D., 74#. Used mostly on pull Bush Hog models of the following series mowers: 109, 115, 126, 160, 166, 205, 206, 207, 220, 255, 256, 257, 268, 305, 306, 307, 310, 315, 405, 406, 502, 600, 1109, 1115, 1126, 1206, 1207, 1209, 1220, 1226, 1257, 1305, 1306, 1307, 1310, 1315, 1405, 1406, 1600, 2315, 2415, 2510, 2512, 2610, 2614, 2615, 3108, 3209, 3368, 3414, 3610, 4214, 4215, 12610, 12615, 13710, CR14R, CR20F. (Part No: 294)
$124.93

Tail Wheel Assembly - 4" x 8" tail wheel assembly with laminated tire. 3-5/8" pilot, 4 bolt holes, 5" bolt circle, 3-3/4" wide, 15" O.D. Used on the following Bush Hog cutters: 12, 104, 105, 109, 126, 205, 255, 275, 285, 305, 306, 307, 405, 405HR, 406, 406HR, 502, 600, 1050, 1051, 1109, 1126, 1207, 1209, 1226, 1306, 1307, 1405 & 1406, 2510, 2512, 3108, 3209, BD90, FH162, S268, SM60, SQ36, SQ480, SQ600. Replaces Sidewinder 15205, Servis Rhino 373024H, Terrain King 373024H, Modern 401-0048, BMB 5337, Hardee C40-RC, King Kutter KK4X8. (Part No: 500BH)
$44.31

Lights
Bracket - Bracket, headlight switch to dash. For tractors: 8N {1948-1950}. (Part No: 8N11671)
$9.35

Bracket - Headlight bracket reinforcement, clear zinc plated for ROUND headlight bracket. For tractors: 8N, NAA {1949-1954}. (Part No: 8N13102)
$9.51

Bracket - Headlight bracket reinforcement, clear zinc plated for WINGED headlight bracket. For tractors: 9N, 2N, 8N {1939-1949}. (Part No: 9N13102)
$9.06

Clip - Clip, {rear lamp wire to brake actuating shaft} 2 required. For tractors: 8N, NAA {1948-1954}. For 321, 339, 340, 501 (Part No: 8N14565)
$11.31

Clip Set - Set of 7 - Clip, headlight wiring to hood. Set of 7. For tractors: 8N, 9N, 2N {1939-1952}. Replaces OEM # 358297S32. 7 Required per tractor. (Part No: 358297S7)
$9.23

Halogen Work Light-Double Bulb - 12 volt lamp assembly, flood pattern, double bulb 55 watt halogen. Includes replaceable 55 watt halogen bulb. (Part No: L982-12V)
$51.42

Headlight Bracket - This round Headlight Bracket will replace the right or left side for models 8N, NAA, Jubilee {1949-1954}. (Part No: 8N13472)
$6.99

Headlight Bracket, Winged Left - Winged Headlight Bracket for Left Side. For tractor models 8N, 9N, 2N, NAA. (Part No: 9N13473)
$21.00

Headlight Reinforcement Plate - Fits Ford tractors from 1939 and up. (Part No: FAA13102A)
$3.27

Headlight Set - 6 Volt - EXACTLY like the factory original with TRACT-O-LITE stamped into housing for tractor models 1939-1954. Will also fit models through 1964 but are not the same diameter as originals. For tractor models 600, 620, 630, 640, 650, 660, 700, 740, 750, 800, 820, 840, 900, 950, 960, 2000, 4000, 8N, 9N, 2N, NAA 1939-1964. This is a pair of headlight assemblies Complete with sealed beam bulb. Spare sealed beam bulbs available as p/n L4019. (Part No: 2N13005-6V)
$202.69

Headlight Set, 12 Volt - For tractor models 600, 620, 630, 640, 650, 660, 700, 740, 750, 800, 820, 840, 900, 950, 960, 2000, 4000, 8N, 9N, 2N, NAA 1939-1964. This is a pair of headlight assemblies Complete with sealed beam bulb. EXACTLY like the original with TRACT-O-LITE stamped into housing. (Part No: 2N13005-12V)
$206.59

Headlight, 12 Volt - 12 Volt, 5-3/4" diameter, sealed beam bulb. Fits 8N, 9N, 2N, Complete assembly is a copy of original headlight, IS NOT EXACTLY LIKE ORIGINAL. Single unit Replaces 13005C or 13006C assemblies (RH or LH). (Part No: S.66419)
$48.99

Headlight, 6 Volt, LH - Left Side for 8N, 9N, 2N, Complete assembly is A copy of original headlight. NOT EXACTLY LIKE ORIGINAL. (Part No: 2N13006C)
$53.25

Headlight, 6 Volt, RH - Right Side for 8N, 9N, 2N, Complete assembly is A copy of original headlight. NOT EXACTLY LIKE ORIGINAL. (Part No: 2N13005C)
$53.25

Knob, Light Switch - Aluminum. For tractor models 8N, 9N, 2N, NAA, Jubilee. (Part No: 9N9703)
$4.65

Light Rim - Headlight door assembly {rim}. For tractors with TRACT-O-LIGHT stamped lights only. For tractors: 8N, 9N, 2N, NAA, Jubilee, 600, 700, 800, 900 {1939-1956}. This Rim is 3/4 inch in width. (Part No: 2N13043)
$20.25

Light Rim - Rim, worklight bulb retainer, O.D. 5-1/4", I.D. 4". For tractor models 8N, NAA, {1949-1954}. (Part No: 8N15513)
$25.71

Light Rim CHROME - For tractors with TRACT-O-LIGHT stamped lights only. For tractors: 8N, 9N, 2N, NAA, Jubilee, 600, 700, 800, 900 {1939-1956}. Replaces 2N13043. (Part No: S.67891)
$19.65

Light Switch - For tractor models 8N, 9N, 2N, NAA, Jubilee. Light Switch with fuse. (Part No: 8N11654B)
$9.98

Magnetic worklight Universal Mounting. - Can be placed anywhere there is a metal surface. 3-1/2" x 6" weather resistant steel body (black), glass lens, flood pattern, 140 ft. beam. Halogen bulb, 12 V, 55 watt, replaceable. 12 ft. cord with cigarette lighter plug. (Part No: L100MAG)
$43.12

Portable Halogen Work Lamp - 3" x 5" sealed beam unit, 12 V, 50 watt, 4 amp. With handle & magnetic base. Projects flood beam pattern 50 ft. wide x 30 ft. long. Lamp is not legal for street use. (Part No: L200MAGH)
$74.75

Retainer 3 Per PGK - Clips, worklight bulb to rim retainer. Set of 3 {special clip to hold bulb assembly in rim}. For tractors: 8N, NAA {1949-1954}. (Part No: 8N15534)
$9.96

Switch, Headlight - Assembly with pigtail wire connectors. This is an EXACT reproduction of the ORIGINAL headlamp switch. For tractor models 8N, 9N, 2N (1939-1949). (Part No: 9N11652)
$8.97

Switch, Light - Switch, Worklight. For tractor models 8N, NAA (1949-1954). (Part No: 8N13740)
$18.96

Tail Light Assembly - Exact as Original in Every Detail. Ford Duolamp (stamped in tailight housing) tractors: 8N, 9N, 2N (1939-1952) (Part No: 8N13404)
$62.73

Tail Light Fender Bracket Pair - These Tail Light Fender Brackets come as a Pair. One Left and one Right for models 8N, 9N, 2N (1939-1952). Replaces: 9N13470, 9N13471 (Part No: 9N13471)
$35.85

Tail Light Wire Clip - For 8N, 9N, 2N, NAA and Jubilee to 1954. Rear Lamp Wire Clip - 6 required per tractor. (Part No: 9N17668)
$3.15

Tail Lite, License Light, Clear Glass Lens - For tractor models 8N, 9N, 2N, NAA, Jubilee, 600, 620, 630, 640, 650, 660, 601, 611, 621, 631, 641, 651, 661, 671, 681, 800, 820, 840, 801, 811, 821, 841, 851, 861, 871, 881 all 1939-1953. (Part No: 9N13445)
$12.75

Tail Lite, License Light, Lens Gasket - For tractor models 8N, 9N, 2N, NAA, Jubilee, 600, 620, 630, 640, 650, 660, 601, 611, 621, 631, 641, 651, 661, 671, 681, 800, 820, 840, 801, 811, 821, 841, 851, 861, 871, 881 all 1939-1953. (Part No: FAA13447A)
$4.90

Taillight Mounting Bracket - Exact of original. Mfg in USA. (Goes between tailight and fender bracket - mounting on top of 9N13470 or 9N13471.)For DUOLAMP tractors 8N, 9N, 2N, NAA, Jubilee, 501, 600, 620, 630, 640, 650, 660, 601, 611, 621, 631, 641, 651, 661, 671, 681, 700, 740, 750, 701, 741, 771, 800, 820, 840, 801, 811, 821, 841, 851, 861, 871, 881, 900, 950, 960, 901, 941, 951, 961, 971, 981, 1811, (2000, 4000 4-cyl), 1801 series. (1949-1954) (Part No: 8N13423)
$16.52

Winged Headlight Bracket - Headlight Winged Bracket for the Right Side. For tractor models 8N, 9N, 2N, NAA. (Part No: 9N13472)
$21.00