FREE SHIPPING on orders above $249.99! Details

• Tractor Parts

• Engine Kits

• Carburetors

• Salvage

• Manuals

• DVDs

• Hats

• Contact Us

• Shipping Rates

• Return Policy

• Ordering Help

• Company Info

• Parts Warranty

• Forums

Ford 445D Tractor Parts

[Categories] [All Ford Models] [Print]

Brakes

Brake Disc - Used in late production, this disc has a 1-9/32 wide facing. This disc is 8.070 inches outside diameter, 2.086 inches inside diameter with 22 splines. Replaces Ford part numbers 86529646, E9NN2N097AA, 83983209, E9NN2A097AA (Item #: 105497, Ref: E9NN2A097AA) $30.90

Brake Rod Seal - For tractor models 345C, 345D, 3550, 420, 445, 445A, 445C, 445D, 455, 455C, 455D, 4400, 4500, 515, 532, 535, 540, 540A, 540B, 545, 545A, 545C, 545D, 550, 555, 555A, 555B, 555C, 555D, 575D, 650, 6500, 655, 655A, 655C, 655D, 675D, 750, 7500, 755, 755A, 755B. Replaces E7NN2N336A, 85999093. (Item #: 105644, Ref: C5NN2N336A) $3.50

Brake Shaft Felt Seal - This Brake Shaft Felt Seal measures 1.470 inch outside diameter, 0.925 inch inside diameter and 0.360 inch thick. Replaces 81826045, 8N3586, D2NN2N171A, 86553476, C5NN3586A (Item #: 124494, Ref: 8N3586) $2.20

Brake Shaft Seal - This Brake Shaft Seal measures 1.565 inch outside diameter, 1-1/16 inch inside diameter. It replaces original part numbers C5NN2473F, C5NN2473H, C5NN2N258C, D2NN2N258A, D8NN2N289AA, D9NN2N289AA, 65968, 83924047. (Item #: 150914, Ref: D9NN2N289AA) $3.30

Clutch

Clutch Disc, 13 Inch - Clutch Disc, 13 inch, 10-spline, 1 inch Hub, no Damper Springs. For 2810, 2910, 335, 3550, 3910, 4110, 420, 4400, 4410, 4500, 4600, 4610, 515, 532, 535. Replaces D1NN7550B, E3NN7550BA, VPG2204, 333008810, 3554214, 81825076, 82006015, 83937180, 1112-6025, 81866447, 87295809. (Item #: 149792, Ref: F0NN7550BA) $98.00

Clutch Kit - This single stage clutch kit contains a 11 inch, 10 spline rigid drive clutch disc (87295808), a 11 inch single pressure plate with six bolt mount, (used 1969 and later) (C9NN7563D), a pilot bearing which measures 1.575 inches OD, .669 inch ID, .472 inches wide (C5NN7600A), new release bearing which measures 4.0700 inches outside diameter, 2.4997 inches inside diameter, 0.8700 inches wide (83914247), and clutch alignment tool. **NOTE** Some tractors use a release bearing which measures 2.0625 inches inside diameter, 3.515 inches outside diameter and .840 inches in width. If you need this smaller bearing, also order part number N1087. For tractor models 2110, 2120, 2150, 2300, 230A, 231, 2310, 233, 234, 2600, 2600V, 2610, 2810, 2910, 3000, 3055, 3110, 3120, 3150, 3190, 3300, 3310, 3330, 334, 335, 345C, 345D, 3600, 3600V, 3610, 3900, 4110, 4140, 4190, 4330, 4340, 4400, 4410, 445C, 445D, 4500, 4600, 4600SU, 4610, 5000, 5190, 530A, 5340, 545C, 545D. (Item #: 183011, Ref: D0NN7563A-KIT) $241.00

Clutch Kit - This new IPTO clutch kit includes a new 13 inch, 29 spline IPTO pressure plate assembly (C5NN7563AC), a new 13 inch, 10 spline drive disc (E7NN7550BB), new pilot bearing (C5NN7600A), new release bearing (83914247), and clutch alignment tool. For tractor models 250C, 260C, 2810, 2910, 3230, 340, 340A, 340B, 3430, 345C, 345D, 3910, 3930, 4110, 4130, 445, 445A, 445C, 445D, 450, 455, 4610, 4630, 4830, 5030, 540, 540A, 540B, 545, 545A, 545C, 545D, 550, 555, 555A, 555B, 655, 655A. (Item #: 112317, Ref: 1112-6163) $315.00

Clutch Kit, 11 Inch IPTO - Kit contains 11 inch 10 spline four pad ceramic disc. (Note, this replaces a three pad triangular type drive disc) C7NN7550AC, 11 inch 29 spline IPTO hub pressure plate with four finger design that will also replace three finger type with six (6) bolt mounting design D8NN7563DB, release bearing 83914247, pilot bearing C5NN7600A, and 1 inch by 10 spline and 1-7/8 inch by 29 spline pilot tool. (Item #: 192660, Ref: 1112-6113) $300.00

Clutch Pedal Return Spring - This Clutch Pedal Return Spring is used on multiple Ford/ New Holland Tractors and Industrial Models, build 1965 and later. It replaces original part numbers C7NN7N598A and 81820895 (Item #: 153432, Ref: C7NN7N598A) $5.30

Cooling System

Water Pump Gasket - Used on multiple Ford models built 1965 and later. Replaces original part numbers D6NN8507A, E5NN8507AA, E5NN8507AB, C5NE9513A. (Item #: 117437, Ref: E5NN8507AB) $0.90

Water Pump Gasket - This is the Water Pump to Pump Housing Gaskets used in Ford/New Holland equipment, 1965 and later. It replaces original part numbers 83959398, E6NN8513AA. (Item #: 117438, Ref: E6NN8513AA) $3.20

Drive Train

Axle Shaft Seal - Seal and Retainer Assembly, Outer, for Rear Axle Shaft. For tractor models 3250C, 260C, 2810, 2910, 3055, 335, 340, 340A, 340B, 345C, 345D, 3550, 3900, 3910, 4000, 4100, 4110, 4140, 4190, 420, 4200, 4330, 4340, 4400, 4410, 445, 445A, 445C, 445D, 450, 4500, 455, 455C, 455D, 4600, 4610, 515, 532, 535, 540, 540A, 540B, 545, 545A, 545C, 545D, 555C, 555D, 575D, 655C, 655D, 675D. Replaces 83999828, C5NN4969B, C5NN4969D, 81819097, 81809097, 81875227, 81859537, F2NN4969AA, E0NN4969AA (Item #: 163590, Ref: C5NN4969D) $15.90

Bearing, Main Input Shaft - Measures 40mm inside diameter, 90mm outside diameter, 23mm wide. Replaces 20943310, 63082RS, 6308, 86511837, 81805130, 81808853, C5NN7A452A, N115069A, 391068X1 (Item #: 183460, Ref: C5NN7A452A) $18.90

Countershaft Gear - Replacing Ford / New Holland part numbers 81804753, C5NN7113B, 81869991, this Transmission Countershaft Gear has 16 and 35 teeth. It is used on Ford models 2000, 2100, 2110, 2110LCG, 2120, 2150, 230, 2300, 230A, 231, 2310, 233, 234, 250C, 2600, 2600N, 2600V, 260C, 2610, 2610V, 2810, 2910, 3000, 3055, 3100, 3110, 3120, 3150, 3190, 3230, 3300, 3310, 333, 3330, 334, 335, 340, 3400, 340A, 340B, 3430, 345C, 345D, 3500, 3550, 3600, 3600N, 3600V, 3610, 3610V, 3900, 3910, 3910N, 3910V, 3930, 3930N, 4000, 4100, 4110, 4110LCG, 4110N, 4110V, 4130, 4130N, 4140, 4190, 420, 4200, 4330, 4340, 4400, 4410, 445, 445A, 445C, 445D, 4500, 455, 4600, 4600SU, 4610, 4610N, 4610SU, 4610V, 4630, 4630N, 4830, 4830N, 5000, 5030, 5100, 515, 5200, 530, 530A, 531, 532, 5340, 535, 540, 540A, 540B, 545, 545A, 545C, 545D, 550, 555, 555A, 555B, 655, 655A, 7000, 7100, 7200 (Item #: 172893, Ref: C5NN7113B) $485.28

Coupling, Counter Shaft Sliding Gear - 21 teeth, 16 spline. For tractor models 2000, 2100, 2110, 2110LCG, 2120, 2150, 230, 2300, 230A, 231, 2310, 233, 234, 250C, 2600, 260C, 2610, 2810, 2910, 3000, 3055, 3100, 3110, 3120, 3150, 3190, 3230, 3300, 3310, 333, 3330, 334, 335, 340, 3400, 340A, 340B, 3430, 345C, 345D, 3500, 3550, 3600, 3610, 3900, 3910, 3930, 4000, 4100, 4110, 4110LCG, 4130, 4140, 4190, 420, 4200, 4330, 4340, 4400, 4410, 445, 445A, 445C, 445D, 4500, 455, 4600, 4610, 4630, 4830, 5000, 5030, 515, 530, 530A, 531, 532, 535, 540, 540A, 540B, 545, 545A, 545C, 545D, 550, 555, 555A, 555B, 5600, 5610, 5610S, 5640, 5700, 5900, 655, 655A, 6600, 6610, 6610S, 6640, 6700, 6710, 7010, 7600, 7610, 7610S, 7630, 7700, 7710, 7740, 7810S, 7840, 8010, 8240, TS100, TS90 all with 8 speed transmission. Replaces C5NN7106B, C7NN7106E, C5NN7102F, D2NN7106B, C5NN7106D, 81819184, 81826589, 81823632, 81813478, E0NN7106BA, 83934545 (Item #: 170135, Ref: E0NN7106BA) $76.00

Deep Groove Ball Bearing Single Row - This bearing measures 50mm inside diameter, 90mm outside diameter, 20mm wide. It is used as PTO Input Shaft Bearing with live PTO. It also has other applications. Confirm by OEM part numbers. Replaces: 6210, 26794660, C5NN7N166B, C0NN7C246B, N115069B, 81854759, 83908455, 84330059, 255090201, 8101-06210, 391162X1, 24101-62104, 971041, 979537, 971129 (Item #: 177372, Ref: C5NN7N166B) $22.90

Differential Bearing and Cup - This Differential Bearing and Cup is used on Ford 2000, 2120, 2N, 3000, 4110, 600, 601, 8N, 9N, Dexta, Jubilee, NAA and other. Replaces original part numbers B4222, BB4222, BB4221B, 510884, 510892, 81709463, 83402421. (Item #: 179801, Ref: 195159M1) $29.60

Differential Lock Coupler - Used in Ford equipment with differential lock, 1965 and later, this part replaces Ford / New Holland part numbers: C5NN4N064A, 81812261, 81871527. This part is used on the following models: 250C, 260C, 2810, 2910, 3000, 3055, 3230, 335, 340, 340A, 340B, 3430, 345C, 345D, 3550, 3900, 3910, 3930, 4000, 4100, 4110, 4130, 4140, 4190, 420, 4200, 4330, 4340, 4400, 445, 445A, 445C, 445D, 450, 4500, 455, 455C, 455D, 4600, 4610, 4630, 4830, 5000, 5030, 5100, 5110, 515, 5190, 5200, 532, 5340, 535, 540, 545, 550, 5500, 555, 5550, 555A, 555B, 555C, 555D, 555E, 5600, 5610, 5610S, 575D, 575E, 5900, 650, 6500, 655, 655A, 655C, 655D, 655E, 6600, 6610, 6610S, 6700, 6710, 6810, 7000, 750, 7500, 755, 755A, 755B, 7600, 7610, 7610S, 7700, 7710, 7810, 7810S, 7910, 8010, 8210, TS100, TS90 (Item #: 180499, Ref: C5NN4N064A) $103.00

Gear, 3rd and 7th - This gear is used on 250C, 260C, 340B, 345D, 445A, 445D, 5000, 530B, 545A, 545D, 5600, 5610, 5900, 6600, 6610, 6700, 6710, 6810, 7000, 7610, 7710. It has 28 and 35 teeth and a 1.555 inch inside diameter. Replaces C9NN7N315B, CNN7N315B, E6NN7N315AA, E6NN7N315BA, 81822962. (Item #: 165995, Ref: C9NN7N315B) $120.00

Gear, 3rd and 7th - Gear has 35 Teeth. It is used on 8 Speed Non Synchro transmission. Replaces OEM part numbers 83960029, 81822962, 83959997, 82987562, C9NN7N315B, E6NN7N315AA, E6NN7N315BA (Item #: 165995, Ref: E6NN7N315BA) $120.00

Gear Shift Knob - This Gear Shift Knob fits 5/16 inch x 24 thread and approx. 1.299 inch diameter. It replaces original part numbers E440GB9, 81800669 (Item #: 121228, Ref: E440GB9) $2.90

Output Shaft Bearing - Measures 41.3mm inside diameter, 73.4mm outside diameter and 19.8mm wide. Replaces: LM501349/501310, 663558R1, 81277C1, 81278C1, GHB142, 663557R91, 86512015, 5132342, 4999261, WAA4221A, 860270, 860297, WAA4222A, WAA4220A, 05132342, 67370, 67371, 644321, 81803417, 860299, 860301, 860302, 860304, 81803412, 860295, 86512015, 5132342, 83992412, 81854761, 81854361, JD8237, JD8902, 663556R91, 663558R1, 86512015, 663557R91, 109706396, GHB142, MBU1044, 113571M1 (Item #: 150013, Ref: 86512015) $14.50

Output Shaft Gear - Gear has 28 and 49 Teeth. It is used an many Ford / New Holland Models with 8 speed and 6x4 Manual Reversing Transmissions. Replaces OEM part numbers C5NN7145A, 83960022, E6NN7145BA, 81804812, E6NN7145AA (Item #: 165990, Ref: E6NN7145AA) $370.00

Output Shaft Pilot Bearing - Measures 25mm inside diameter, 52mm outside diameter, 16.25mm wide. It replaces: E76GA9, C5NN7N014A, 86705858, C5NN7N047A, C5NN7N044A, 83990517, 81804636, 81804637, C5NN7N048A, F718701030030, 339482X1, 3010151X91, 194145-11910, 971326, 30205, 30205M-TIM, 30205M (Item #: 185088, Ref: C5NN7N014A) $14.90

PTO Input Bearing Retainer Seal - The Seal Measures Oil seal, 1.878 inches inside diameter, 3.130 inches outside diameter, 0.5000 inches wide. It replaces OEM numbers E59GE9, 83924923, D9NNC729BA, 87712923 (Item #: 172919, Ref: D9NNC729BA) $7.20

PTO Input Housing Gasket - Used on many Ford / New Holland tractors, 1965 and later. It replaces OEM part numbers 81804648, C5NN7N051B, E7NN7N051AA (Item #: 179416, Ref: C5NN7N051B) $1.00

Rear Axle to Center Housing O-Ring - This Rear Axle to Center Housing O-Ring is used on multiple Ford / New Holland Models. It is number 1 in the image. This O-Ring should always be replaced when changing brake disc on oil immersed systems. 13.50 inch inside diameter x .139 inches thick. Replaces 379313S91, 83417133, VPJ7202, 47P3852 (Item #: 113943, Ref: 379313S91) $6.40

Shift Cover Assembly - 6/8 speed with dipstick hole. Fits 2600, 3600, 4600, 2610, 2810, 2910, 3610, 3910, 4610, 230A, 231, 250C, 260C, 335, 340, 340A, 340B, 345D, 420, 445, 445A, 445C, 445D, 530A, 531, 540, 540A. Includes cover, levers, lever knobs and lever boots. Order C5NN7N225A gasket and 83929967 dipstick separately. Replaces D3NN7211A. (Item #: 178429, Ref: D3NN7211A) $130.00

Shift Cover Gasket - This Transmission Shift Cover Gasket is used on multiple Ford Tractors, 1965 an later with 6, 7 or 8 speed transmissions. It replaces original part numbers 82004680, 83959206, C5NN7N225C, D5NN7223B, D8NN7223AA, E6NN7223AA, E8NN7223AA. (Item #: 125339, Ref: C5NN7N225A) $4.30

Transmission Gasket Set - Transmission Gasket Set for 3 cylinder Fords, 1965 and up with 6 or 8 speed Non-Synchro Transmissions. (Item #: 178201, Ref: S.65396) $28.50

Transmission Output Shaft Seal - Measures 39.4mm inside diameter x 60.3mm outside diameter x 12.7mm wide. It replaces C5NN77086A, 81808572, D66412, D40772, 363514R93, 70800166, ATY3988, ATY4067, AM848T, AP19243H, ATY4124, 1860325M1, 195506M1, 1077452M1 (Item #: 155727, Ref: C5NN77086A) $5.90

Transmission Rear Coupling - This a a paired set used on many Ford New Holland Models. Replaces OEM part numbers 83908698, 82983825, 83960027, E6NN7N072BA, D6NN7N072B (Item #: 167824, Ref: E6NN7N072BA) $73.00

Electrical System

Alternator - This is a 70 amp unit with battery sensor. D+, D+, B+ and W terminals. Has 'Lucor' connector as well under plastic terminal protector. It replaces 81863039, 82857207, E7NN10B376AB, F0NN10B376BB, 54022336, 54022336D, 63324273, LRA02690, MG0283, MG283, MAN141 (Item #: 111070, Ref: E7NN10B376BB) $120.00

Alternator New - Alternator Assembly, 70 amp. For 250C, 260C, 3230, 3430, 345C, 345D, 3930, 4130, 445C, 445D, 455C, 455D, 4639, 4830, 5030, 545C, 545D, 555C, 555D, 5610S, 575D, 655C, 655D, 6610S, 675D, 7010S, 7610S, 7810S, 8010. (Item #: 111070, Ref: E7NN10B376BB) $120.00

Ignition Switch - This Ignition Switch comes with two Keys. It replaces E8NN11N572AB, E8NN11N572AA, E7NN11N572AA (Item #: 121140, Ref: E8NN11N572AB) $25.10

Ignition Switch, Keyed - This 5 position, 7 terminal ignition switch comes with 2 key. Used on many tractor models (2000, 3000, 4000, 5000, 7000 1965-1975), 8000-9700, TW10, TW20, TW30, all 1968-1982. For 2600-7700 1975-1981. For 230A, 231, 233, 234, 333, 334, 335, 420, 515, 530A, 532, 535, all 1981-1990. For 7810-8210 1982-10/1985. For TW5-TW35 to 5/1983-2/1990. 8530-8830 3/1990 and up. Starter and Heat Ignition Switch for tractors with cold start. Not for Shibaura built tractors. Replaces OEM 82849085, 81871583, 81838692, 83999543, 83902803, E7NN11N501AB, D3NN11N501A, D5NN11N501A, C5NN11N501A, E7NN11N501AC, 83959710, 83976890, E7NN11N501AA, E8NN11N501AA (Item #: 116913, Ref: E7NN11N501AB) $8.70

Starter - With single contact solenoid, 12 volt, 10 tooth, clockwise rotation. For tractor models (231 1975-81 with 3-158 dsl), (233 1975-77 with 3-158 dsl), (250C, 260C 1990-94 with 3 cyl dsl), (333 1975-77 with 3-175 dsl), (335 1975-78 with 3-175 dsl), (340 1979-81 with 3-175 dsl), (340A, 340B 1981-84 with 3-175 dsl), (345C 1989-92 with 3 cyl dsl), (345D 1992-97 3 cyl dsl), (445 1979-83 3-183 dsl), (445A 1984-88 3-183 dsl), (445C 1989-92 with 3-183 dsl), (445D 1992-98 with 3-183 dsl), (515, 531 1975-81 with 3-201 dsl), (535 1975-77 with 3-201 dsl), (540A 1981-84 with 3-201 dsl), (540B 1984-88 with 3-201 dsl), (545 1979-83 3 cyl dsl), (545A 1984-88 with 3 cyl dsl), (545C 1989-92 with 3 cyl dsl), (545D 1992-98 with 3 cyl dsl), (550 1975-78 with 3 cyl dsl), (620, 622 1967-74 gas and dsl). Replaces 26395, 26211, 26339A. (Item #: 100300, Ref: SLU0002) $150.00

Starter, Diesel, Gear Reduction - Gear Reduction Starters offer higher torque than a direct drive starter. This can be useful for diesel engines. This is a gear reduction replacement for our part SLU0002. Replaces 81833782, 81859494, C7NN11000C, D4NN11000A, D0NN11000A, D2NN11000A, 81859398, 81826488, D7NN11000A, D6NN11000A, D8NN11000CD, D8NN11000CB, D8NN11000CA, E2NN11000AA, D2NN11000B, D5NN11001A, D4NN11000B, D7NN11000B, D8NN11000DA29Z, D8NN11000CE, E3NN11000AA, D9NN11000AA, K262761, K308650, LRS212, 26395, 26211, 26339A (Item #: 181969, Ref: 80855520) $190.00

Starter Safety Wire Assembly - For tractor models (2000, 3000, 4000 with 6 or 8 speed trasnmissions 10/1966 to 1975), 2600, 3600, 4600, 2610, 2810, 2910, 3610, 3910, 4610, 230A, 231, 250C, 260C, 335, 340, 340A, 340B, 345D, 420, 445, 445A, 445C, 445D, 530A, 531, 540, 540A. Replaces D4NN7A488B, D4NN7A488BB, E4NN7A488BB, E4NN7A488CA, 81827298, 83948129, 83963950 (Item #: 125405, Ref: D4NN7A488BB) $17.90

Voltage Regulator - This is a 12v, 14.4 volt set, A-circuit, with battery temp sensor. Fits alternators: E7NN10B376AB, E7NN10B376BB, E3NN10B376AD, 81863039, 81863039, 81868798. Fits on the back of Lucas/Marelli alternators. Replaces E8NN10316AA, 83981529 (Item #: 182960, Ref: E8NN10316AA) $38.40

Voltage Regulator - Used on Motorola equipped units: 230A, 2310, 234, 250C, 2610, 2810, 2910, 334, 335, 340, 340A, 340B, 345C Indust/Const, 345D Indust/Const, 3610, 3910, 4110, 445 Indust/Const, 445C Indust/Const, 445D Indust/Const, 450 Indust/Const, 4610, 5110, 530A, 530B, 540A Indust/Const, 540B Indust/Const, 545A Indust/Const, 545C Indust/Const, 545D Indust/Const, 5610, 5900, 6410, 6610, 6710, 6810, 7410, 7610, 7710, 7810, 7910, 8210, 8530, 8630, 8730, 8830, TW15, TW25, TW35, TW5 12v, round terminal plug with four male connectors. (Item #: 182912, Ref: E4NN10316BA) $84.00

Engine Bearings

Main Bearing Set, 158, 175 and 201 Gas or Diesel and 192 Gas, .010 - Replaces 3-CFPN6333B and 1-EBPN6337B. 1 kit used per engine. Non-Flanged Main Bearings. Flanged Thrust Bearing. (Item #: 106315, Ref: MBK633-010) $78.00

Main Bearing Set, 158, 175 and 201 Gas or Diesel and 192 Gas, .020 - Replaces 3-CFPN6333B and 1-EBPN6337B. 1 kit used per engine. Non-Flanged Main Bearings. Flanged Thrust Bearing. (Item #: 106316, Ref: MBK633-020) $63.00

Main Bearing Set, 158, 175 and 201 Gas or Diesel and 192 Gas, .030 - Replaces 3-CFPN6333B and 1-EBPN6337B. 1 kit used per engine. Non-Flanged Main Bearings. Flanged Thrust Bearing. (Item #: 106317, Ref: MBK633-030) $39.10

Main Bearing Set, 158, 175 and 201 Gas or Diesel and 192 Gas, STD - Replaces 3-CFPN6333B and 1-EBPN6337B. 1 kit used per engine. Non-Flanged Main Bearings. Flanged Thrust Bearing. (Item #: 106314, Ref: MBK633) $80.00

Engine Gaskets

Crank Seal, Front - Fits 3, 4 and 6 Cylinder Engines in: 2000, 2600, 3000, 3600, 3610, 3910, 4000, 4600, 4610, 5000, 5600, 5700, 6000, 6600, 6610, 6640, 6700, 6710, 7000, 7600, 7610, 7700, 7710, 8000, 8160, 8200, 8240, 8260, 8340, 8360, 8560, 8600, 8700, 9000, 9200, 9600, 9700, TS80, TS90, TW10, TW20, TW30. 60MM X 89MM X 12MM. Replaces 81813951, 81815927, 83999512, 1815927, F0NN6700CA, 83908809, 87800348, 87800696, 87802755, C5NN6700A, D5NN6700A (Item #: 106352, Ref: D5NN6700A) $9.00

Oil Pan Gasket - For the following 3 Cylinder Gas or Diesel Engines: 158, 175, 192, 201 CID, used in tractors 1965 and newer: 2000, 2100, 2110, 2110LCG, 2120, 2150, 230, 2300, 230A, 231, 2310, 233, 234, 2600, 2600N, 2600V, 2610, 2610V, 2810, 2910, 3000, 3055, 3100, 3110, 3120, 3150, 3230, 3300, 3310, 333, 3330, 334, 335, 3400, 340A, 3430, 345C, 345D, 3500, 3550, 3600, 3600N, 3600V, 3610, 3610V, 3900, 3910, 3910N, 3910V, 3930, 3930N, 4000, 4100, 4110, 4110LCG, 4110N, 4110V, 4130, 4130N, 4140, 420, 4200, 4330, 4340, 4400, 4410, 445, 445A, 445C, 445D, 450, 4500, 455, 455C, 455D, 4600, 4600SU, 4610, 4610N, 4610SU, 4610V, 4630, 4630N, 5000, 5100, 515, 5200, 530A, 531, 532, 5340, 535, 540, 540A, 540B, 545, 545A, 545C, 545D, 550, 555, 555A, 555B, 55A, 5600, 5700, 6600, 6700, 7000, 7100, 7200, 7600, 7630, 7700. Replacing 83990594, D0NN6710B, 87295239, 81824481, 1824481, F0NN710AA. (Item #: 106335, Ref: F0NN6710AA) $9.80

No
Picture
Overhaul Gasket Set - 4000 6/1969-1975, 4600 1975-1981, and others with 201 CID Diesel. Overhaul Gasket Set with Crankshaft Seals. (Item #: 172316, Ref: OGS201) $74.00

Rear Seal Gasket - Gasket, Crankshaft Rear Seal Retainer. For 230A, 231, 2310, 233, 234, 250C, 2600, 2600N, 2600V, 2610, 2610V, 2810, 2910, 3000, 3230, 333, 334, 335, 3430, 345C, 345D, 3600, 3600N, 3600V, 3610, 3610V, 3900, 3910, 3910N, 3910V, 3930, 3930N, 4000, 4100, 4110, 4110N, 4110V, 4130, 4130N, 4140, 420, 4200, 4330, 445C, 445D, 4600, 4600SU, 4610, 4610N, 4610SU, 4610V, 4630, 4630N, 4830, 4830N, 5000, 5030, 5110, 515, 530A, 531, 532, 535, 545C, 545D, 550, 555, 555A, 555C, 555D, 5600, 5610, 5700, 575D, 5900, 6410, 655, 655A, 655C, 655D, 6600, 6610, 6700, 6710, 675D, 6810, 7100, 7200, 7410, 755, 755B, 7600, 7610, 7630, 7700, 7710, 7810, 7910, 8000, 8030, 8200, 8210, 8530, 8600, 8630, 8700, 8730, 8830, 9000, 9200, 9600, 9700, TW10, TW15, TW20, TW25, TW30, TW35, TW5. Replaces 3959128, 83959128, 83957246, 81813951, E9NN6N305AA, 81864478, 81864478GV, 87554506, E5HN6N305AC, E9NN6N305AB, VPC5311 (Item #: 172805, Ref: E9NN6N305AB) $4.00

Engine Parts

Camshaft Plug - Used on Ford engines: 158, 175, 192, 201, 233, 256, 268, 401 this camshaft plug replaces part numbers C5NND851B, 83994133, C5NND851A, 1816594 (Item #: 166919, Ref: C5NND851B) $43.30

Connecting Rod - This new Connecting Rod used a 1.50 inch piston pin. It is used on Ford diesel engines: 192, 201, 233, 256, 268, 401 and Ford gas engines: 192, 201, 233, 256. It replaces OEM part numbers C7NN6205. Casting numbers: C7NN6205A, E5NN6205AA, E1TN6205AD. VERIFY CASTING NUMBERS BEFORE ORDERING. (Item #: 128642, Ref: C7NN6205) $103.00

Crankshaft Pulley - Used on Ford / New equipment built 1965 and later. This is a single groove pulley. This pulley is not for Shibaura built compacts. Replaces D5NN6A312A, 83903583 (Item #: 154921, Ref: D5NN6A312A) $125.00

Crankshaft Pulley Spacer - Used on many Ford / New Holland models, 1965 and later, this is a keyed spacer. It fits behind the crankshaft pulley. Replaces OEM part numbers 83995427, 1811427, 81811427, C5NE6B306A, C5NE6C306A (Item #: 154924, Ref: C5NE6B306A) $20.30

Ring Gear, Flywheel - For gas and diesel. Measures 16.115 outside diameter, 14.52 inside diameter, .625 width and has 128 teeth. For models 2000, 3000, 4000, 5000, 6000, 7000, all 1965-1975. For 2600, 3600, 4600, 5600, 6600, 7700, all 1975-1981. For 5000 gas 6/1971-1975. For 3230, 3430, 3930, 4130, 4430, 4830, 5030, 3/1990 and up. Also used on many industrials and later models. Replaces C5NE6384AA, 83949153, 82954183, 9710967, 500791, 18042303, 80873368, 873368, 3949153. Starter Flywheel Ring Gear. (Item #: 111310, Ref: E2NN6384AA) $41.20

Exhaust System

Exhaust Manifold, Vertical - This Vertical Exhaust Manifold fits 3-cylinder tractors 1975 and newer models: 445, 445A, 445C, 445D, 450, 455, 455C, 455D, 535, 540, 545, 545A, 545C, 545D, 550, 555, 555A, 555B, 2310, 2600, 2610, 2810, 2910, 3230, 3430, 3600, 3610, 3910, 3930, 4100, 4110, 4130, 4600, 4610, 4630. Does not come with gaskets. Mounting Gasket available as part number C5NE9448A. (Item #: 101522, Ref: D3NN9430A) $41.50

Fuel System / Air Intake

Air Cleaner Dust Collector - This Air Cleaner Dust Collector Valve has a 3 inch inside diameter. It is used on multiple Ford/New Holland models. It replaces original part numbers 81870839, D2NN9C673B, F0NN9C673AA. (Item #: 121925, Ref: T23262) $6.60

Air Filter, Outer - For tractor models (550, 555 from 1975 to 7/1981), (555A, 555B from 1975 and later), (2600, 3600, 3900, 4100, 4600 from 4/1976 and later). Measures 11.45 inches long, 5.30 inch outside diameter, 3.03 inch inside diameter. Replaces D5NN9601A, D5NN9601B, D6NN9601A, E6NN9601A, E9NN9601BA, 83908364, 3414560, 0003414560, AZA194, 9583, CR9583, 9583M, P526500, LAF8551 (Item #: 121138, Ref: D6NN9601A) $15.50

Fuel Cap, Vented - 2-7/8 inch outside diameter, silver finish, 1-3/4 inches edge of tang to edge of tang, vented, includes gasket. For tractor models TW5, TW10, TW15, TW20, TW25, TW30, TW35 -- Industrial: 230A, 231, 233, 234, 250C, 260C, 333, 334, 335, 340, 340A, 340B, 3400, 345C, 345D, 3500, 3550, 420, 4400, 445, 445A, 445C, 445D, 450, 4500, 455C, 455D, 515, 530A, 531, 532, 535, 540, 540A, 540B, 545, 545A, 545C, 545D, 550, 555, 555A, 555B, 555C, 555D, 555E, 650, 6500. (Item #: 184806, Ref: C5NN9030D) $10.30

Fuel Injector - 30 Series with 201 CID. For tractor models 4630, 4680, L885, 3910, 3930, 4130. (Item #: 112307, Ref: E9NN9F593CA) $77.00

Fuel Injector Seal Kit - For (1) injector on: post 1965 tractors with 3 -6 cylinders models. Includes cork dust seal, copper compression seal and 2 aluminum return line seals. Replaces Replaces: 380428S, 380428S43, 81806142, 81806277, 81821105, 81867564, 83995430, C5NE9E529A, C5NE9F596A, C5NE9G546A (Item #: 156291, Ref: C5NE9F596A) $2.20

Fuel Pump - Hand Primer. For tractor models 5900, 5610, 6610, 6710, 7610, 7710, 3230, 3430, 3930, 4130, 4630, 4830, 5030, 250C, 260C, 345C, 345D, 445C, 445D, 545C, 545D, 555C, 555D, 575D, 655C, 655D, 675D, 755B. Replaces F1NN9A384BA, 81874144, 83964115. (Item #: 117599, Ref: F1NN9A384BA) $36.50

Throttle Rod Connector - This Throttle Rod Connector is made from plastic. It is used on Ford 2000, 3000, 4000, 4000SU, 5000, 7000, 2600, 3600, 4600, 4600SU, 5600, 6600, 7600, 7700, 2310, 2610, 2810, 2910, 3610, 3910, 4610SU, 5610, 6610, 7610, 7810, 5900, 5640, 6640, 7740, 7840, 8240, 8000, 9000, 8600, 9600, 9700, 231, 335, 531, 340, 540, 3400, 3500, 445, 4500, 250C, 340, 340A, 340B, 345C, 345D, 445, 445A, 445C, 445D, 540, 540A, 540B, 545, 545A, 545C, 545D, 550, 555, 555A, 655, 655A. Replaces C5NN9740A, 81811646 (Item #: 167626, Ref: C5NN9740A) $9.00

Throttle Rod Grommet - This Throttle Rod Grommet is used on Ford Tractors 1953 to 1974. It Replaces original part numbers: 353873S, 83416731, 83935151. (Item #: 164360, Ref: 353873S) $2.60

Gauges

Fuel Sender - Fuel Sender with gasket, screw held. Used on some Ford Tractors, 1965 and later. Verify part number. Replaces E3NN9A316CA and 83943961. (Item #: 102189, Ref: 83943961) $59.00

Temperature Sender - Temperature Sender, Water. The part may come with a spade terminal which might require changing your wire end. 3/8 Inch NPT Thread.Replaces: 81818428, 83904449, 83904448, 81837742, 83911735, 83948391, 8712608, 82028131, 9712608, D8NN10884AA, E1NN10884AA, 2080406, 3917490, 73403367 (Item #: 128314, Ref: D5NN10884A) $11.31

Hitch / Drawbar

Lower Lift Arm, Cat II - Left or right hand, 34.646 inch center hole to center hole, 3.504 inch wide, .709 inch thick, Rigid Forged Type Ends. For tractor models 250C, 260C, 2810, 2910, 3000, 3055, 3230, 3430, 345D, 3550, 3900, 3910, 3930, 4000, 4100, 4110, 4130, 4200, 4330, 4340, 4400, 4410, 445D, 4500, 4600, 4610, 4630, 4830, 5030, 515, 532, 535, 545D. Color varies. Replaces 82002004, C5NN555AL, C7NN555S. (Item #: 122629, Ref: 81821330) $130.00

Hydraulic System

Draft Control Shaft - This Draft Control Shaft is 8-3/4 inches long. It is used on multiple Ford Models. Replaces original part number D3NNB911B, 81843896, 81843986 (Item #: 180164, Ref: D3NNB911B) $48.00

Hydraulic Fluid Filler Cap - Hydraulic Fluid Filler Cap is used on the following Ford equipment, 1965 and later: 2000, 3000, 4000, 4000SU, 5000, 7000, 2600, 3600, 4600, 4600SU, 5600, 6600, 7600, 7700, 2310, 2610, 2810, 2910, 3610, 3910, 4610SU, 5610, 6610, 7610, 7810, 5900, 3230, 3430, 3930, 4130, 4630, 4830, 5030, 5640, 6640, 7740, 7840, 8240, 8000, 9000, 8600, 9600, 9700, TW5, TW10, TW15, TW20, TW25, TW30, TW35, 231, 335, 531, 340, 540, 3400, 3500, 445, 4500, 250C, 340, 340A, 340B, 345C, 345D, 445, 445A, 445C, 445D, 540, 540A, 540B, 545, 545A, 545C, 545D, 550, 555, 555A, 555B, 555C, 655, 655A, 655B, 655C, 655D. 1 3/8 inch thread. Replaces C5NNN901A, 81802102 (Item #: 163813, Ref: C5NNN901A) $9.70

No
Picture
Hydraulic Lift Arm, Left Hand - This Left Hand Hydraulic Lift Arm is used on FORD 3900, 4100, 4600, 2810, 2910, 3610, 3910, 4610, 3230, 3430, 3930, 4630, 4830, 5030, 250C, 345C, 345D, 420, 445, 445A, 445C, 445D, 450, 515, 532, 535, 540, 540B, 545, 545A, 545B, 545C, 545D. It Replaces D3NNB921A. (Item #: 131822, Ref: D3NNB921A) $187.00

Hydraulic Lift Arm, Right Hand - This Right Hand Hydraulic Lift Arm is used on FORD 3900, 4100, 4600, 2810, 2910, 3610, 3910, 4610, 3230, 3430, 3930, 4630, 4830, 5030, 250C, 345C, 345D, 420, 445, 445A, 445C, 445D, 450, 515, 532, 535, 540, 540B, 545, 545A, 545B, 545C, 545D. It Replaces D3NNB920A. (Item #: 178945, Ref: D3NNB920A) $179.94

No
Picture
Hydraulic Pump - This is a new Ford Hydraulic Pump. It is used on 8x8 transmission, transmission mounted, with 3 point lift, with Relief Valve start year: 12/01/1988. It is used on 250C, 260C, 345C, 345D, 445C, 445D, 545C, 545D. It replaces original part numbers 83962224, E8NN600AA. (Item #: 157622, Ref: E8NN600AA) $700.00

Hydraulic Pump - Fits the following tractors (less Synchro Transmission) using Transmission Mounted Pump with Relief Valve: 4600, 2810, 2910, 3900, 3910, 4100, 4110, 4610, 3230, 3400, 3430, 3930, 4130, 4630, 4830, 5030, 250C, 260C, 340A, 340B, 345C, 345D, 420, 455A, 445S, 445D, 515, 532, 535, 540A, 540B, 545A, 54C, 545D. Uses D4NN915A Gasket, not included. Replaces 83936585, D8NN600LB, D3NN600B, D6NN600E, D8NN600LA, D8NN600LB-E, D8NN600LBV, VPK1016, 81836736, 83908243, 83926104, 83936585 (Item #: 104254, Ref: D8NN600LB) $350.00

Hydraulic Pump Gasket - Hydraulic Pump Gasket is used on fits pumps D8NN600KB and D8NN600LB. It replaces original part numbers 83961379, D4NN915A, E7NN915AA (Item #: 156043, Ref: D4NN915A) $5.10

Hydraulic Pump Wobble Shaft Thrust Plate - This Wobble Shaft Thrust Plate (Bearing) is used in Piston Style Pumps. Fits Models: NAA, Jubilee, 231, 335, 340, 340A, 340B, 345C, 345D, 445, 445A, 445C, 445D, 531, 540, 541A, 540B, 545. 545A, 545C, 600, 601, 611, 620, 621, 630, 631, 640, 641, 650, 651, 660, 661, 671, 681, 700, 701, 740, 741, 750, 771, 800, 801, 811, 820, 821, 840, 841, 850, 851, 861, 871, 881, 900, 901, 941, 950, 951, 960, 961, 971, 981, 2000, 2600, 2610, 2810, 2910, 3000, 3400, 3500, 3600, 3610, 3910, 4000, 4500, 4600. It replaces original part numbers NCA858A, 81802059, C0NN858A. (Item #: 178969, Ref: C0NN858A) $48.21

Lift Cover Gasket - Used of Ford Tractors 1965 and later, this gasket replaces OEM part numbers 957E502, E7NN502AA, C5NN502A, 83963584 (Item #: 113960, Ref: C5NN502A) $3.10

Lift Cylinder Safety Valve - This Lift Cylinder Safety Valve has 3/4 x 16UNF Right Hand Threads. It is used on Ford / New Holland 231, 2310, 233, 234, 250C, 2600, 260C, 2610, 2810, 2910, 3230, 333, 334, 335, 340, 340A, 340B, 3430, 345C, 345D, 3600, 3610, 3900, 3910, 3930, 4100, 4110, 4130, 420, 445, 445A, 445C, 445D, 4500, 4600, 4610, 4630, 4830, 5000, 5030, 5100, 5110, 515, 5200, 531, 532, 5340, 535, 540, 540A, 540B, 545, 545A, 545C, 545D, 5600, 5610, 5610S, 5640, 5700, 5900, 6410, 6600, 6610, 6610S, 6640, 6700, 6710, 6810, 7000, 7010, 7100, 7200, 7410, 7600, 7610, 7610S, 7630, 7700, 7710, 7740, 7810, 7810S, 7840, 7910, 8010, 8210, 8240, 8340, 8530, 8630, 8730, 8830, TS100, TS90, TW15, TW25, TW35, TW5. Replaces 81838679, D3NN984C, D5NN984A, 83911832 (Item #: 170948, Ref: D5NN984A) $40.70

Miscellaneous

Loader Bucket Cylinder Seal Kit - For Ford Construction and industrial models 345C, 345D, 445C, 445D, 455C, 455D, 545C, 545D, 555C, 555D, 555E, 575D, 575E, 655C, 655D, 655E, 675E Replaces Ford OEM number 85804740, , Compatible with New Holland Construction and industrial models LB75, Replaces New Holland OEM number 85804740, (Item #: 158414) $40.80

Loader Lift Cylinder Seal Kit - For Ford Construction and industrial models 345C, 345D, 445C, 445D, 455C, 455D, 545C, 545D, 555C, 555D, 575D, 655C, 655D, 675D, Replaces Ford OEM number FP417, (Item #: 158423) $53.00

Oil System

Oil Dipstick - This Dipstick is 7 7/8 inches long. It is used on many Ford agriculture and industrial models, 1975 and later. Replaces: 87801534, C7NN6750C, C9NN6750A, D3NN6750C, D3NN6750D, D3NN6750E, D4NN6750B, D4NN6750D, D6NN6750B, E9NN6750BA, 81816867, 81822073, 81837146, 81837147, 81843818, 83902286, 83905287, 83918846, 83982499 (Item #: 113916, Ref: E9NN6750BA) $8.50

$Ford 445D Pump Gear\Shaft Assembly$
Pump Gear/Shaft Assembly - Gear and Shaft Assembly, Oil Pump Drive. For models: TW5, TW15, TW25, TW35, 2000, 2310, 2600, 2610, 2810, 2910, 3000, 3230, 3400, 3430, 3500, 3550, 3600, 3610, 3900, 3910, 3930, 4000, 4100, 4110, 4130, 4600, 4610, 4630, 4830, 5000, 5030, 5110, 5610, 5700, 5900, 6410, 6500, 6600, 6610, 6700, 6710, 6810, 7000, 7100, 7200, 7410, 7700, 7710, 7810, 7910, 8000, 8210, 8530, 8600, 8630, 8700, 8730, 8830, 9000, 9600, 9700, 230A, 233, 234, 250C, 260C, 333, 334, 335, 420, 445, 445A, 445C, 445D, 450, 455, 455C, 455D, 515, 530A, 531, 532, 535, 540, 540A, 540B, 550, 555, 555A, 555B, 555C, 555D, 650, 655, 655A, 655C, 655D, 750, 755, 755A, 755B. Replaces E9NN6A820AA, 87800008, C7NN6A820C, D3NN6A820E, 3984954, 81845748, 73345660, 81822957, 81837148, 83984954, 81843777, 81834095, D3NN6A820F, D3NN6A820G, C7NN6A820A, D0NN6A820A, C7NN6A820B, D3NN6A820A, D3NN6A820D, 87764586, 87764587, 81859340, 81844832, 81845749, 81818742, 87763956, D3NN6A820B (Item #: 140555, Ref: E9NN6A820AA) $32.40

PTO / Driveline

Input Shaft Seal - Used with Transmission driven PTOs. It is used am many Ford / New Holland Tractors. Measures I.D. 1.0675 inch, O.D. 2.1940 inch, W. 0.5000 inch. (Metric 28.5 x 55.5 x 12.4mm). Replaces E81GD9, D9NN7R510BA, 83924524, 83924924 (Item #: 173499, Ref: D9NN7R510BA) $4.50

PTO Brake Arm - This PTO Brake Arm is used on 250C, 260C, 2810, 2910, 3230, 335, 340, 340A, 340B, 3430, 345C, 345D, 3550, 3900, 3910, 3930, 4000, 4100, 4110, 4130, 420, 4400, 445, 445A, 445C, 445D, 4500, 455C, 455D, 4600, 4610, 4630, 4830, 5030, 515, 531, 532, 535, 540, 540A, 540B, 545, 545A, 545C, 545D (Item #: 173002, Ref: C9NNN747A) $23.80

PTO Clutch Pack Sealing Ring - This PTO Clutch Pack Sealing Ring is used with D2NNN751D and E0NNN751BA Clutch Packs. 2.375 Inch Outside Diameter. Three used per tractor. Replaces 8313283, 81809513 and 313283. (Item #: 168315, Ref: 313283) $4.10

PTO Clutch Plate, External Splines - This Disc is used in tractors with Independent PTOs. It measures 5.47 inches Major/ 5.278 inches Minor Outside Diameter, 3.91 inches Inside Diameter, 0.070 inches Width, 54 Teeth. 1P77518A, 83918314, C8AP7B442A, P77573A1, T100680, V32773200 (Item #: 155469, Ref: C8AP7B442A) $4.90

PTO Countershaft Gear - This PTO Countershaft Gear has 33 teeth and 29 splines. It replaces original part numbers 82847570, E9NN702AB, E9NN701AB. Used on 3230, 3430, 3930, 4130, 4630, 4830, 5030 (Item #: 152251, Ref: E9NN702AB) $465.00

PTO Cover - This PTO Cover is used on 3230, 3430, 3930, 4130, 4630, 4830, 5030, 345C, 345D, 445C, 445D, 545C, 545D. Replaces part numbers 83990098, E8NN733AB, E8NN733AC (Item #: 152249, Ref: E8NN733AC) $539.94

PTO Drive Gear - This PTO Drive Gear has 33 Teeth, 27 Splines. Used on 3230, 3430, 3930, 4130, 4630, 4830, 5030. Replaces E9NNA726AA, 83982999 (Item #: 180249, Ref: E9NNA726AA) $271.37

PTO Gear - This PTO Gear has 30 Teeth and 29 splines. It is used on 3230, 3430, 3930, 4130, 4630, 4830, 5030. Replaces E9NNA727AB, 83983010 (Item #: 180250, Ref: E9NNA727AB) $176.00

PTO Input Shaft - 15 Tooth Input Shaft. Fits 2810, 2910, 3900, 3910, 4100, 4110, 4600, 4610 (most industrial and utility models after 1975 with 8 speed or 6x4 Manual Reversing Transmission). 4000 (1965 and newer) Note: Can Replace the 17 tooth Input Shaft on 4000 models prior to 1972 BUT you must also order Gear Assembly part number D1NN791A. (Item #: 115256, Ref: D1NN772B) $199.00

PTO Output Cover Gasket - Used on many Ford / New Holland Tractors built 1965 and later. Replaces OEM part numbers C5NN7086A, 81815558 (Item #: 179414, Ref: C5NN7086A) $4.50

PTO Seal - This PTO Input Shaft Oil Seal is for models with live or independent PTO. Seal Measures .984 inches inside diameter, 1.496 inches outside diameter and .236 inches in width. For models Dexta, Super Dexta, (2000, 3000 and 4000 all with 6, 7 and 8 speed transmissions), (2610, 3610, 4100, 4110, 4600, 4610 all with 8 speed transmission). Replaces part numbers A-VPH1413 and 81717245. (Item #: 173453, Ref: 957E727A) $4.80

PTO Shaft - This PTO Shaft fits multiple Ford Tractors and industrial Models with Independent PTO. PTO shaft is 30.625 inches long, 26 tooth splines. Uses Sleeve E7NN797BA and Seal D9NN703BB (not included). It replaces D8NN725AB, 83937198. (Item #: 163804, Ref: D8NN725AB) $258.00

PTO Shaft Bearing, Front - For tractor models: Dexta, Super Dexta, NAA, Jubilee, 501, 600, 601, 700, 701, 800, 801, 900, 901, 2000, 2110LCG, 2310, 2600, 2610, 2810, 2910, 3000, 3400, 3500, 3550, 3600, 3610, 3910, 3900, 4000, 4100, 4110, 4110LCG, 4400, 4500, 4600, 4610, 5000, 5600, 5610, 5610S, 5900, 6600, 6610, 6610S, 6700, 6710, 6810, 7600, 7610, 7610S, 7700, 7710, 7810S, 8010. All WITH 1 3/8 Inch DIAMETER PTO SHAFT. WILL NOT FIT 1 1/8 Inch DIAMETER PTO SHAFT. Replaces 81800755, C5NN7118A, 20705250, E75GE9 (Item #: 178129, Ref: E75GE9) $6.60

Seats

Seat Armrests - This is an armrest assembly. It can be used with T222BU if desired. (Item #: 181995, Ref: AR22BL) $40.30

Seat Assembly - This is a complete seat assembly. It is used on the following, 8/1992 and later without cabs: 345C, 345D, 445C, 445D, 545C, 545D, 250C, 260C, 3230, 3430, 3930, 3930N, 3930NO, 4130, 4130N, 4130NO, 4630, 4630N, 4630NO, 4630O, 4830, 4830N, 4830O, 5030, 5030O. Armrests are available as part number R22BL. Replaces E9NN400AB99M, E9NN400AA, 86605775 (Item #: 101383, Ref: T222BU) $122.00

Seat Cushion, Black - This Black Pan and Cushion Assembly for deluxe suspension seat fits tractor models: 2000, 3000, 4000, 5000, 7000 (1965-2/1969 and 2/1970-1975), 2600, 3600, 3900, 4100, 4600, 5600, 6600, 231, 233, 333, 335, 515, 531, 532 (1975-1981), 2610, 2910, 3610, 3910, 4110, 4610, 231, 234, 334, 335 (1981-2/1990), 1110, 1210, 1310, 1510, 1710, 1910, 2110 (1983-1987), 5610, 5900, 6610 (1981-10/1985). For hinged seat on 1000, 1600 (1973-1978), 1100, 1200, 1300, 1500, 1700, 1900 (1979-10/1983), 1110, 1210, 1310, 1510, 1710, 1910, 2110 (1983-1987). Replaces D1NNA405B, D2NNA405B, D2NNA405BAK, E2NNA405AA99B. (Item #: 101228, Ref: E2NNA405AA99M) $108.00

Seat Cushion, Blue - This Pan and Cushion Assembly for deluxe suspension seat fits tractor models: 2000, 3000, 4000, 5000, 7000 (1965-2/1969 and 2/1970-1975), 2600, 3600, 3900, 4100, 4600, 5600, 6600, 231, 233, 333, 335, 515, 531, 532 (1975-1981), 2610, 2910, 3610, 3910, 4110, 4610, 231, 234, 334, 335 (1981-2/1990), 1110, 1210, 1310, 1510, 1710, 1910, 2110 (1983-1987), 5610, 5900, 6610 (1981-10/1985). For hinged seat on 1000, 1600 (1973-1978), 1100, 1200, 1300, 1500, 1700, 1900 (1979-10/1983), 1110, 1210, 1310, 1510, 1710, 1910, 2110 (1983-1987). Replaces C7NNA405R, D0NNA405C, D1NNA405A, D1NNA405B, D2NNA405B, D2NNA405BAK, D8NN400BABB, E2NNA405AA99B, E2NNA405AA99M, E7NN400GA, E7NN420AA. (Item #: 101227, Ref: E2NNA405AA99MBL) $100.00

Suspension Seat - New Ford/New Holland replacement seat. Complete seat with suspension, blue. Fits Ford / New Holland Compact tractor models: 1110, 1210, 1310, 1510, 1710, 1910; Fits Industrial/Construction models: 340A, 340B, 345D, 3500, 445, 445A, 445C, 445D, 450, 515, 540A, 540B, 545A, 545C, 545D; Tractor models: 2100, 2110, 2120, 2150, 2300, 231, 2310, 234, 2600, 2810, 2910, 3000, 3055, 3100 3300, 3310, 3330, 3600, 3610, 3910, 4000, 4100, 4110, 4200, 4330, 4340, 4400, 4410, 4600, 4610, 5000, 5100, 5200, 531, 532, 5600, 5900, 6600, 6700, 7000, 7100, 7200. There is a plate on the bottom that is 4 inches wide and 8 1/4 inches long. In the center of this plate are 2 slots that are 3/8 inches wide, 1/4 inch from each edge and 1/2 inch apart and they are about 4 inches long. Overall width is 19.5 inches, overall length of base is 15.25 inches, overall height of base is 9.25 inches. (Item #: 101226, Ref: CSA698-8V) $215.00

Sheet Metal / Body Parts

Hood Prop Rod - This hood prop rod is 17 1/2 inches and used on 2000, 3000, 4000, 4000SU, 5000, 7000, 2600, 3600, 4600, 4600SU, 5600, 6600, 7600, 7700, 2310, 2610, 2810, 2910, 3610, 3910, 4610SU, 5610, 6610, 7610, 7810, 5900, 231, 335, 531, 340, 540, 3400, 3500, 445, 4500, 250C, 340, 340A, 340B, 345C, 345D, 445, 445A, 445C, 445D, 540, 540A, 540B, 545, 545A, 545C, 545D. It Replaces original part number C7NN8042A. (Item #: 178161, Ref: C7NN8042A) $9.20

Steering

Axle Fork and Shaft, Outer - Carraro 4WD front ends on Ford models 5610, 6610, 6810, 7610, 7710, 250C, 260C, 345C, 345D, 445A, 445C, 445D, 450, 455C, 545A, 545C, 545D, 555B, 555C, 555D, 655, 655A, 655C. This part replaces 83952526, CAR40760, N13510 (Item #: 156151, Ref: CAR40760) $250.00

Half Shaft Inner Seal - The measurements on this seal are: 62mm outside diameter, 42mm inside diameter, 14mm wide. This seal is used on the inner portion of a half shaft on Carraro front axles. Replaces OEM numbers 9968001, 73403999, CAR116723, 83952335, 1966164C1, 09968001, 3475332M1, KH1213, VKH1213 (Item #: 129289, Ref: CAR116723) $12.10

Hub Seal, MFWD - Extensively used on Carraro mechanical four wheel drive front axles, this hub seal measures 149mm (5.86614 inches) x 176mm (5.86614 inches) x 16mm (0.629921 inches). Replaces OEM numbers 9968085, K395102, 47108806, 83996064, 82920209, 294169A1, 247877A1, 130182A1, 1349265C1, CAR126324, CAR47705, 3225110, 0003225110, 82920209, 3996064, 83996064, 83957862, 9968085, 153326219, 153326621, 1349265C1, 153326301, 09968085, 83952509, 83952530, CAR118556, CAR126324, CAR47705, CAR126390, 3501510M1, 3475598M1, 3475533M1, 3523062M1, 3541510M1 (Item #: 157753, Ref: 247877A1) $56.00

Hydraulic Cylinder Seal Kit - For Ford Construction and industrial models 445D, 455C, 555C, 555D, 575D, 655C, 655D, 675D, Replaces Ford OEM number FP419, (Item #: 168943) $60.00

Hydraulic Cylinder Seal Kit - For Ford Construction and industrial models 345C, 345D, 445C, 445D, 545C, 545D Replaces Ford OEM number FP459, , Compatible with New Holland Construction and industrial models B95, B95LR, B95TC, B110, B115, LB75, LB75B, LB90, LB90B, LB110, LB110B, LB115, LB115B, Replaces New Holland OEM number 87428620, (Item #: 168944) $27.60

Kingpin - MFWD Lower - For Ford / New Holland tractors with Mechanical Four Wheel Drive: 345C, 345D, 445, 445A, 445C, 445D, 450, 455C, 455D, 545, 545A, 545D, 555B, 555C, 555D, 575D, 655, 655A, 655C, 655D, 675D, 250C, 260C, 4610N, 5640, 6640, 6640O, 7740, 7740O, 7840, 7840O, 8240, 8340. This part replaces OEM numbers 83952503, CAR118526, 3475348M1, 153326212, 137700410835, N13504 (Item #: 156167, Ref: 83952503) $86.00

Power Steering Cylinder - This power steering cylinder is right hand on 4 wheel drive and left hand on 2 wheel drive. It measures 14.75 inches long and comes with ball joints has hydraulic ports of 1/4 inch 18 NPT. For models 340A, 340B, 345C, 345D, 445, 445A, 445C, 445D, 450, 540A, 540B, 545A, 545C, 545D, 555C, 555D, 575D, 655C, 655D, 675D, 250C, 260C. Also replaces 85999104, D8NN3D547AA, D8NN3D547AB. (Item #: 160294, Ref: 85999337) $265.00

Power Steering Cylinder - This power steering cylinder is left hand on 4 wheel drive and right hand on 2 wheel drive on 2 cylinder systems. Hydraulic ports of 1/4 inch 18 NPT. For models 340A, 340B, 345C, 345D, 445, 445A, 445C, 445D, 450, 540A, 540B, 545A, 545C, 545D, 555C, 555D, 575D, 655C, 655D, 675D, 250C, 260C. Replaces 85999338, 85999103, D8NN3A540AA, D8NN3A540AB. VERIFY PART NUMBER TO ENSURE YOU ARE ORDERING THE CORRECT CYLINDER. (Item #: 160295, Ref: 85999338) $220.00

Power Steering Motor - This power steering motor is used on the following Ford/New Holland models: 3910N, 3910V, 4110V, 4610V, 555C, 555D, 575D, 655C, 655D, 675D, 250C, 260C, 340, 340A, 340B, 345C, 345D, 445, 445A, 445C, 445D, 450, 540, 540A, 540B, 545, 545C, 545D. It replaces original part numbers 86585454, E3NN3A244DA, D8NN3A244AA. (Item #: 160077, Ref: E3NN3A244DA) $950.00

Power Steering Pump - For tractor models 345C, 345D, 445, 445A, 445C, 445D, 450, 455, 545, 545A, 545C, 545D, 550, 555, 555A, 555B, 655, 655A. Replaces D8NN3K514DC, E6NN3K514GA, E7NN3K514CA-E (Item #: 157714, Ref: E7NN3K514CA) $381.00

Power Steering Pump - Dynamatic, Ford, E9NN3K514BA - For Ford Construction and industrial models 445C (12/88-8/93), 445D (9/92-9/96), 555C (11/88-8/93), 555D (9/93-7/96), 575D (9/93-7/96), 655C (11/88-8/93), 655D (9/93-7/96), 675D (9/93-7/96), Replaces Ford OEM number E9NN3K514BA, E9NN3K514BB, 81871798, Genuine Dynamatic pump, Manufactured to exact OEM specifications, To validate your warranty: A contaminated system should be completely flushed by an authorized dealer. Use new, clean fluid and filters, (Item #: 157744) $591.00

Power Steering Pump Repair Kit - Kit repairs the following pumps: E6NN3K514EA, D8NN3K514KC, E0NN3K514AB, and E6NN3K514AB. Note, this kit contains 1 -Double Lip Seal. If your pump uses 2 - Single Lip Seals, use part number DHPN3A674B (Item #: 187034, Ref: 83910651) $13.60

Reservoir Cap, Power Steering Pump - Used on E6NN3K514EA, D8NN3K514GC, C9NN3A674D Power Steering Pumps. For tractor models 231, 233, 2600, (3500, 3550 5/1970 to 1975), 3600, (4100 4/1970 to 1975), (420, 4600, 5600, 6600, 7600 1975 to 1981), 4600SU, (5100, 7100 7/1970 to 1975) and others. (Item #: 121241, Ref: D2NN3A006B) $3.70

Spindle Repair Kit, Less Spindle - 1.23 inch pin, less spindle, with unfinished bushings. For tractor models 7010, 8010, 250C, 260C, 340B, 345C, 345D, 445A, 445C, 445D, 450, 540B, 545A, 545C, 545D, 555A, 555B, 655A. (Item #: 125386, Ref: EFPN3115A) $96.00

No
Picture
Spindle Repair Kit, With Spindle - 1.23" pin, with spindle, finished bushings. For tractor models 7010, 8010, 250C, 260C, 340B, 345C, 345D, 445A, 445C, 445D, 450, 540B, 545A, 545C, 545D, 555A, 555B, 655A. (Item #: 178370, Ref: S.75083) $457.00

Steering Motor Seal Kit - This Steering Motor Seal Kit has a 1.776 inch seal. It is used on Ford / New Holland models 5110, 5610, 5900, 6410, 6610, 7610, 7710, 7810, 8210, 8530, 8630, 8730, 8830, TW5, TW15, TW25, TW35, 445C, 445D, 550, 555, 555A, 555B, 555C, 555D, 575D, 655C, 655D, 675D. Replaces 83945793, F1NN3N991AA, E3NN3R513BA, E3NN3N991BA, 81871236, 86585241 (Item #: 178956, Ref: F1NN3N991AA) $178.00

Steering Sector Shaft Seal - Two of these felt seals are used per tractor. It measures 1.470 inch outside diameter, 0.925 inch inside diameter and 0.360 inch thick. Replaces 81826045, 8N3586, D2NN2N171A, 86553476, C5NN3586A (Item #: 124494, Ref: 8N3586) $2.20

Tie Rod End, Carraro - Right Hand - For Ford Construction and industrial models 250C, 260C, 345C, 345D, 445, 445A, 445C, 445D, 450, 455, 455C, 455D, 545, 545A, 545C, 545D, 550, 555, 555A, 555B, 555C, 555D, 575D, 655, 655A, 655C, 655D, 675D (All with FWD), Replaces Ford OEM number 83930617, CAR87031, Length 4.160", 24 x 1.5 RH MM Thread, Right Hand Tie Rod End, Manufactured by Carraro to exact OEM specifications, For an economy version use Item #: 104702, (Item #: 159941) $107.00

Tie Rod End, Economy - Right Hand - For Ford Construction and industrial models 250C, 260C, 345C, 345D, 445, 445A, 445C, 445D, 450, 455, 455C, 455D, 545, 545A, 545C, 545D, 550, 555, 555A, 555B, 555C, 555D, 575D, 655, 655A, 655C, 655D, 675D (All with FWD), Replaces Ford OEM number 83930617, CAR87031, Length 4.160", 24 x 1.5 RH MM Thread, Right Hand Tie Rod End, For Carraro Version use Item #: 159941, (Item #: 104702) $29.90

Universal Joint - Many mechanical four wheel drive front axles use this universal joint. This part has 27mm cup diameter and is 70.9mm across (1.063 X 2.791 inches). Replaces OEM numbers 247543A1, 81882C1, 1-33-742-629, 137700420872, 144461A1, 137700420874, 195215A1, 337260A1, D149733, B507526, CAR40869, N14156, N14411, 9968059, 84355357, 85807283, 84990205, 9970163, 85805996, 87306931, CAR40889, 81874740, 85805996, 9968059, 09968059, 1-33-742-629, CAR40825, 84355357, AL71316, RE212902, ABP3002508, 508360, ABP3004431 (Item #: 158432, Ref: CAR40825) $57.00

Upper King Pin - Upper King Pin is used on Ford / New Holland models: 345C Indust/Const, 345D Indust/Const, 445C Indust/Const, 445D Indust/Const, 545C Indust/Const, 545D Indust/Const, 555C Indust/Const, 555D Indust/Const, 555E Indust/Const, 5610S, 5640, 575D Indust/Const, 575E Indust/Const, 655C Indust/Const, 655D Indust/Const, 655E Indust/Const, 6610S, 6640, 6640O, 675D Indust/Const, 675E Indust/Const, 6810S, 7610S, 7740, 7740O, 7840, 7840O, 8240, 8340, B110 Indust/Const, B110B Indust/Const, B90B Indust/Const, B95 Indust/Const, B95B Indust/Const, B95BTC Indust/Const, B95LR Indust/Const, B95TC Indust/Const, LB110 Indust/Const, LB110.B Indust/Const, LB75 Indust/Const, LB75.B Indust/Const, LB90 Indust/Const, LB90.B Indust/Const, LB95 Indust/Const, TB100, TB110, TB120, TB80, TB85, TB90, TS6000, TS6020, TS6030. Replaces CAR14063, CAR128880, 122260A1, 3523549M1, 47108555, 9968923 (Item #: 153436, Ref: 9968023) $56.00

Wheels

$Ford 445D Front Hub, Heavy Duty \ Industrial$
Front Hub, Heavy Duty / Industrial - Used on Heavy Duty and Industrial Front Ends. 3000, 4000 (4cyl, heavy duty front axle), 5100, 5110 (heavy duty axle), 5200, 5190, 5600 (10x16 tire), 5610 (heavy duty axle), 5700 (10x16 tire), 6600 (10x16 tire), 6610 (heavy duty axle), 6700 (10x16 tire), 6710 (heavy duty axle), 7100, 7200, 7410 (heavy duty axle), 7600 (10x16 tire), 7610 (heavy duty axle), 7700 (10x16 tire), 7710 (heavy duty axle), 8000, 8010, 9000, TW10, TW20, TW30, Industrial: 250C, 260C, 335, 340, 340A, 340B, 345C, 345D, 420, 445, 445A, 445D, 450, 515, 532, 535, 540, 540A, 540B, 545, 545A, 545C, 545D, 1801, 3400, 3500, 3550, 4400, 4500, 4410. It uses C5NN1107F studs, and WBKFD7 wheel bearing kit, not included. Replaces OEM part number 313020. Verify part number before ordering. (Item #: 100662, Ref: 313020) $72.00

Front Wheel Bearing Kit - For tractor models (5000, 7000 1972 and up with 8 x 16 wheel), 8000, 8600, 8700, 9000, 9600, 9700, (TW10, TW20, TW30 less heavy duty), (5610, 6610, 6710, 7610, 7710, 10/1989 and up heavy duty axle), 3400, 3550, 4400, 4500, 335, 340, 340A, 340B, 345C, 345D, 420, 445, 445A, 445C, 445D, 515, 535, 540, 540A, 540B, 545, 545A. NOTE: check bearing and cup numbers before ordering. Replaces 8L4221/312518, 25590-25520 for Inner Bearing and Cup, 312520/312548, 02474/02420 Outer Bearing and Cup, E4NN1190AA Seal. (Item #: 100657, Ref: S.67455) $44.30

Rear Rim Bolt Kit - This Rear Rim Bolt Kit is a set of six bolts, nuts and washers. They are 5/8 inches-18 x 2.82 inches long. Replaces: 33806S34, 33806S36, 33806S7, 350719S8, 370938S36, 370938S43, 408, 81821369. (Item #: 184824, Ref: 350719KIT) $23.00

Universal Parts and Accessories
Category: Accessories / Supplies

Accessories / Supplies

Auxiliary Heater, Universal - This universal auxiliary heater is used for tractor cabs, combines, backhoes, dozers, forklifts, etc. using 5/8 inch heater hose connections. Hot water forced air heat. Dimensions: 6-1/2 inches x 9-1/2 inches x 9 inches, steel powder coat housing with aluminum core. 3-speed high volume squirrel cage fan, 12-volt, 20, 000 BTU includes switch, brackets, instructions. (Item #: 182644, Ref: MIS3127) $385.00

Magnetic Block Heater - Universal. Magnetic utility heater. 120 volt AC, 200 Watts. Built-in thermostat maintains optimum temperature - will not exceed 250 degree F (121 degree C). Quick-grip handle protects hands from heat. 4-3/8 inches (11cm) length, 2-1/2 inches (6.3cm) width, 3 inches (7.5cm) height (including handle). (Item #: 178758, Ref: MBH1153) $97.00

Cooling System

Thermostat Housing to Block Gasket - Tractors: all 4-cylinder, 1953-1964, gas and diesel. Bolt holes measure 3/8 inch in diameter, and center to center of bolt hole spacing is 2 3/4 inches. Sold and Priced as Each. (Item #: 191970, Ref: EAF8255A) $5.20

Decals and Emblems

Decal, Fear This Ford - 12-1/2 inches x 3 inches. For all Ford tractors. (Item #: 183476, Ref: S.67825) $15.80

Sherman Transmission Instruction Plate - For Ford models with Sherman step up step down transmission. Installs under steering wheel nut. (Item #: 178113, Ref: SHERMAN) $20.20

Drive Train

Shift Cover Plate Gasket - For all models with 5-SPEED transmission built between 1955-1964. Not for tractors made overseas, such as Major, Dexta, etc. (Item #: 178105, Ref: NDA7223A) $6.40

Electrical System

NOTE

Alternator - Don't see the Alternator you need for your tractor? We have many alternators not listed on this website (for tractors 1953 and newer). Just call us at 800-853-2651.

NOTE

No
Picture
Alternator, 12 Volt - Universal 63 Amp Delco Alternator. Single wire with built in regulator. Will fit most tractors pre 1980. (Item #: 111377, Ref: 8NE10305SE) $96.00

Alternator Conversion Plug - Used to turn Delco SI Style 2-Wire plug alternators into self-exciting style. (Item #: 178026, Ref: ADR9209) $14.40

Alternator Top Adjusting Bracket, Universal - Universal Top Adjusting Bracket for Alternator or Generator is 7/8 inches wide, 1-1/2 inch offset, 8-1/4 inch from farthest end of slot to center of mounting hole, 3-3/4 inch slot length, 3/8 inch mounting hole. (Item #: 173326, Ref: 8NL10302) $25.20

No
Picture
Battery Thermal Wrap - 60 Watt, 28 inches long wrap to keep your battery warm. (Item #: BTW28) $35.98

No
Picture
Battery Thermal Wrap - 160 Watt, 36 inches long wrap to keep your battery warm. (Item #: BTW72) $53.81

No
Picture
Coil - This universal automotive style coil is 28, 000 volts for a 12 volt system, 2.9 ohms. Measures 6 inches long and 2 1/2 inches diameter. (Item #: 182583, Ref: 28010) $49.20

No
Picture
Spark Plug - Extended tip, 14mm thread, 3/8 inch reach. Replaces Champion J10Y, J11Y, J12Y, J13Y. NOTE: Verify spark plug type before ordering. (Item #: 179437, Ref: AL85) $5.60

Spark Plug - Standard tip, 14mm thread, .472" reach. Replaces Champion L9J, L10, L86, L86C, L88A, L90. NOTE: Verify spark plug type before ordering. (Item #: 182459, Ref: AL425) $4.80

NOTE

Starter - Don't see the starter you need for your tractor? We probably have it! Just call us at 800-853-2651 with your make, model, engine cubic inches (CID) and number off your old starter and we will see if we can find it!

NOTE

Starter Solenoid, 12 Volt - This is a 3 post, 12 volt Starter Solenoid. Can be used as a saddle mount or flat surface mount. May come in a metal or plastic casing. (Item #: 150223, Ref: DR1467) $19.20

Switch, Push Button - This 2 terminal switch has many applications. It is a heavy duty momentary switch, push for on and release for off. It is rated for up to 35 volts. Uses two screw terminals. The mounting stem is 5/8 inch number 32 thread. It is 21/32 inch overall length. Check measurements before ordering if using as a universal part. Applications include ether switch, horn button, cold start, starter switch, and manifold heater switch. It replaces 22702, 240962, 242988, 245866, 245936, 70253322, 71191589, 72160068, VT507, 86900358, A30858, O9995AB, T18524, TG07803, TO18117, TO7803, 271179R91, 367678R91, 373611R91, 393209R91, AR46184, AR47373, AR47374, R39554, 189158M91, 767828M91, 105386A, 10A972, 1K7392C, UT2421, 1K7392A, 7A7392. (Item #: 121141, Ref: R7994) $13.40

Engine Gaskets

Silicone Blue RTV - Permatex ultra blue, no leak RTV silicone gasket, oil resistant, use on valve covers, oil pans, timing covers, water pumps. Temperature range -75 degree F to +500 degree F, 3.35 ounce tube. (Item #: 178141, Ref: PRM77BR) $10.90

Engine Parts

NOTE

Valve Overhaul Kits - Valve Overhaul Kits are located in the Engine Overhaul Kits Section (if available for this tractor).

NOTE

Engine Pistons and Sleeves

No
Picture
Seal Kit - Seal kit, for cylinder E2NN3A540BA. Piston rod is retained with 1" snap ring and 1-3/4" threaded spanner nut. (Item #: E2NN3X-SK) $64.99

Engine Rings

NOTE

Piston Ring Sets - Don't see the correct ring set for your tractor? Give us a call and ask for a Hastings Ring Set (made in USA). We need the following information to correctly find the set you need: 1. Engine size and type (Ex: 233 CID Gas) 2. Number of engine cylinders, 3. Cylinder bore size, 4. Number and size of compression rings for each piston (Ex: (2) 3/32"), 4. Number and size of oil rings for each piston (Ex: (1) 5/32").

NOTE

Exhaust System

Chrome Exhaust Stack - Single Wall, 48 inches long with a slotted, 2 inch inside diameter inlet. This is a universal part. Verify Measurements before ordering. (Item #: 118823, Ref: ZNL89020C) $81.00

Chrome Exhaust Stack - Single Wall, 48 inches long with a slotted, 2.5 inch inside diameter inlet. This is a universal part. Verify Measurements before ordering. (Item #: 119038, Ref: ZNL89025C) $108.00

Chrome Exhaust Stack - Single Wall, 48 inches long with a slotted, 3.00 inch inside diameter inlet. This is a universal part. Verify Measurements before ordering. (Item #: 114858, Ref: ZNL89051C) $135.00

Chrome Exhaust Stack - Single wall, 53 inches long with a slotted, 3.00 inch inside diameter inlet with extended curve. This is a universal part. Verify measurements before ordering. (Item #: 173286, Ref: 146520CHR) $106.00

Chrome Exhaust Stack - Single wall, 53 inches long with a slotted, 3.50 inch inside diameter inlet. It has an extended curve on the outlet. This is a universal part. Verify measurements before ordering. (Item #: 173287, Ref: 146490CHR) $161.00

Chrome Exhaust Stack - Single Wall, 48 inches long with a slotted, 4.00 inch inside diameter inlet. This is a universal part. Verify Measurements before ordering. (Item #: 114945, Ref: ZNL89057C) $145.00

Chrome Exhaust Stack - Single Wall, 48 inches long with a slotted, 5.00 inch inside diameter inlet. This is a universal part. Verify Measurements before ordering. (Item #: 119080, Ref: ZNL89485C) $174.00

Chrome Exhaust Stack - Single Wall, 42 inches long with a slotted, 2.50 inch inside diameter inlet. This is a universal part. Verify Measurements before ordering. (Item #: 173281, Ref: L102236CHR) $88.00

$Ford 445D Muffler Clamp, 1-1\4$
Muffler Clamp, 1-1/4 - New Clamp for 1-1/4 inch outside diameter muffler inlet. (Item #: 182682, Ref: MC114) $2.10

$Ford 445D Muffler Clamp, 1-3\4$
Muffler Clamp, 1-3/4 - New Clamp for 1-3/4 inch outside diameter muffler inlet. (Item #: 108866, Ref: MC134) $4.80

$Ford 445D Muffler Clamp, 1-3\8$
Muffler Clamp, 1-3/8 - New Clamp for 1-3/8 inch outside diameter muffler inlet. (Item #: 182687, Ref: MC138) $2.90

$Ford 445D Muffler Clamp, 2-1\4$
Muffler Clamp, 2-1/4 - New Clamp for 2-1/4 inch outside diameter muffler inlet. (Item #: 108870, Ref: MC214) $5.30

$Ford 445D Muffler Clamp, 2-3\4$
Muffler Clamp, 2-3/4 - New Clamp for 2-3/4 inch outside diameter muffler inlet. (Item #: 108872, Ref: MC234) $8.71

Muffler Clamp, 3 - New Clamp for 3 inch outside diameter muffler inlet. (Item #: 108873, Ref: MC300) $7.40

$Ford 445D Muffler Clamp, 3-1\2$
Muffler Clamp, 3-1/2 - New Clamp for 3-1/2 inch outside diameter muffler inlet. (Item #: 108874, Ref: MC312) $8.00

Muffler Clamp, 4 - New Clamp for 4 inch outside diameter muffler inlet. (Item #: 108875, Ref: MC400) $8.30

Muffler Clamp, 5 - New Clamp for 5 inch outside diameter muffler inlet. (Item #: 118841, Ref: MC500) $12.70

Rain Cap - This rain cap is for a 1.750 inch pipe. (Item #: 108632, Ref: R1799) $11.00

Rain Cap - This rain cap is for a 2.0 inch pipe. (Item #: 108633, Ref: R1800) $8.80

Rain Cap - This rain cap is for a 2.50 inch pipe. (Item #: 108635, Ref: R1802) $12.50

Rain Cap - This rain cap is for a 2.750 inch pipe. (Item #: 108636, Ref: R1804) $11.00

Rain Cap - This rain cap is for a 4.00 inch pipe. (Item #: 108645, Ref: R1807) $12.90

Rain Cap - This rain cap is for a 4.50 inch pipe. (Item #: 108749, Ref: WC14) $13.40

Rain Cap - This rain cap is for a 5.00 inch pipe. (Item #: 108750, Ref: WC15) $17.40

Stainless Steel Clamp, 2.75 Inch - This Stainless Steel Clamp is used with Chrome Stacks and in other applications. (Item #: 179749, Ref: ZNL90872A) $6.50

Stainless Steel Clamp, 4 Inch - This Stainless Steel Clamp is used with Chrome Stacks and in other applications. (Item #: 185428, Ref: ZNL90875A) $8.50

Fuel System / Air Intake

Air Cleaner Filler - Fits many air cleaners that use steel wool type filler. Custom manufactured mesh. 1 bag = 3-1/2 inch x 3-1/4 inch. (Item #: 151026, Ref: S.43231) $14.00

Filter Screen and Gasket for Sediment Bowl - 1-1/2 inch outside diameter seal (for a 1 9/16 inside diameter housing and a 1 3/8 inch outside diameter screen. Measure before ordering. For tractor models (1958-1964 All with 134 cubic inch engines), 2000 4 cylinder, 501, 601, 701, (1958-1960 all with 172 cubic inch engines up to 126524), 801, 901, 1801. (Item #: 150700, Ref: ABC346) $5.70

Fuel Tank Screen - This Fuel Tank Screen is used with most stem-type sediment bowls to further protect against debris in the gas line. It has a 0.216 inch Insert Pipe outside diameter - 2.53 inch Overall Length. (Item #: 114940, Ref: R7949) $9.92

Gauges

Ammeter, Black, Flat Bezel - For all models to 1958. Terminal type ammeter. 30-0-30. Black ring. Replaces FAD10850A. (Item #: 110410, Ref: A0NN10670A-BLAC) $10.70

No
Picture
Hourmeter - DC voltages from 12 volt thru 36 volt nominal. Heavy duty glass-reinforced polyester body. Internal shock shields and grommets protect movement from shock and vibration damage. Fits 2-1/4 inch opening, three (3) mounting screws with nuts and two (2) blade terminals included. (Item #: 178318, Ref: HM771) $63.00

Hourmeter, Analog - 2 inch, black. Can be used on any tractor with a 12 to 24 volt electrical system. (Item #: 178285, Ref: S.52672) $42.30

Oil Line Adapter - Oil Gauge fittings may be different even for the same models. Here is an Oil Line Adapter if you have a gauge line without removable fittings, this converts 1/8 inch pipe thread to 1/8 inch tube. Brass. (Item #: 179540, Ref: 919095) $16.00

Hitch / Drawbar

Drawbar Check Chain Kit - This Drawbar Check Chain Kit includes: right hand/left hand anchors, 2 eyelets, 2 chains, 4 clevis with pins, and hardware. Fits: Jubilee, NAA, NAB, 2000 3 Cylinder, 2000 4 cylinder, 2600V, 2N, 3600V, 4000 4 Cylinder, 501, 600, 601, 700, 701, 800, 801, 8N, 900, 901, 2030, 2031, 2100, 2110, 2111, 2120, 2121, 2130, 2131, 2300, 2310, 2600, 2610, 2810, 2910, 3000, 3110, 3120, 3300, 3330, 3600, 3610, [4030, 4130, 4140 (4 cylinder)], 4031, 4040, 4100, 4110, 4120, 4121, 4131, 9N, Industrial: 231, 233, 333, 334, 335, 1801, 1811, 1821, 1841, 1871, 1881, 230A, 3400, 3500, 530A, Dexta, Super Dexta. Replaces: 957E597, 957E596, CBPN598A, NCA597B, NCA596B. (Item #: 115051, Ref: NCA596B) $40.60

Drawbar, Heavy Duty, Heat Treated - Standard Heat Treated Drawbar Red, 30 1/2 inch L hole center to hole center, 2 1/2 inch wide, 1 1/8 inch thick (drawbar fits lift between lift arms). (Item #: 103174, Ref: 9N5182) $42.10

Hair Pin Assortment - 15-piece assortment. Includes four (4) of HP-3 (wire diameter 3/16 inch, length 3.75 inch), four (4) of HP-4 (wire diameter 5/32 inch, length 2 15/16 inches), four (4) of HP-5 (wire diameter 1/8 inch, length 2 9/16 inches), and three (3) of HP-6 (wire diameter 3/32 inch, length 1 5/8 inches). (Item #: 182461, Ref: HPA15X) $11.40

Link End - Plated, forged, 1-1/4 inch thread, left hand, 1 inch hole. (Item #: 180473, Ref: RE1717L) $19.00

Link End - Plated, forged, 1-1/4 inch thread, right hand, 1 inch hole. (Item #: 174507, Ref: RE1718R) $21.27

Stabilizer Arm HD - Arm only, made of alloy spring steel, for kit 231253XHD, red only. 7/8 inch hole diameter. 31 1/2 inches center to center. (Item #: 110516, Ref: 230042XHD) $15.20

Top Link - Forged Top Link, 12 inch body, Category I implement ends. Adjusts 17.5 to 24 inches overall. 3/4 inch pin holes and both eyelets are 1 3/4 inch wide. Dichromate plated. (Item #: 103162, Ref: JSA1012C) $20.00

Universal Drawbar Lock - For Cat. 1 drawbars up to 1 1/2 inch thick and 3 inches wide. Prevents drawbar from rotating. (Item #: 112156, Ref: DBL2) $37.00

Hydraulic System

Coupler Flange - FORD: Drive flange; 5/8 inch round bore with set screw 1/4 inch x 3/8 inch # SSH4-6. Hydraulics: Drive flange; 5/8 inch round bore with set screw 1/4 inch x 3/8 inch # SSH4-6. 2-1/4 inch b-b (Item #: 108772, Ref: L36-6) $64.00

Coupler Flange - Drive flange; 3/4 inch round bore with set screw 1/4 inch x 3/8 inch. 1-15/16 inch spacing. For Morflex series 302. Replaces: L363, 191061, 1752219M91, L36-3 (Item #: 112104, Ref: 191061) $22.00

Coupler for Pump Shaft - The Hydraulic Pump Shaft Coupler is 1-1/2 Outside Diameter and 2-1/4 inches long. It 7/8 inch 13 splined inside. It replaces 1631413, 350-1631413, S340 (Item #: 114586, Ref: S340) $36.00

Coupler Hub Drive Kit - Coupler Complete, Morflex Series 302. Contains center member, 2 drive flanges with set screws, and 4 bolts with lock nuts. The center member is 3-1/8 inch diameter, with four 1/4 inch holes and 1-15/16 inch spacing.The drive flange is 3/4 inch round bore with set screw 1/4 inch by 3/8 inch. (Item #: 112067, Ref: L601-14) $124.00

Cylinder Seal Kit, For 2 inch cylinders - For TISCO side and top link replacement cylinders. Seal Repair Kit for 2 inch cylinders. For cylinder numbers: HTL2101, HTL2102, HTL2103, HSL2201, HSL2202, HSL2203. Replaces HSK2001. (Item #: 183971, Ref: HSK2002) $24.50

Cylinder Seal Kit, For 3 inch Cylinders - For TISCO brand side and top link replacement cylinders ONLY. Seal Repair Kit for 3" cylinders. For cylinder numbers: HTL3101, HTL3102, HTL3103, HSL3201, HSL3202, HSL3203. Replaces HSK3001. (Item #: 179480, Ref: HSK3002) $32.10

Filter Element - 25 Micron replacement element for SF1-25. (Item #: 182541, Ref: 1A9023) $15.40

Filter Element - 10 Micron replacement element for SF1-10. (Item #: 120092, Ref: 1A9021) $13.60

Hub - 7/8 inch, 13 spline threaded, 3-7/8 inch hole spacing. For 730 LOADER. Used with C5NNN879A hub. (Item #: 160204, Ref: 291315) $65.00

Hydraulic Hose Assembly-NPT, 12 inch - Universal. 12 inch overall length. 1/2 I.D. 2 Wire. Solid Male 1/2 NPT thread on both ends. (Item #: 118257, Ref: H42-2M-12) $11.00

Hydraulic Hose Assembly-NPT, 180 inch - Universal. 180 inch (15 Feet) overall length. 1/2 inch inside diameter. 2 Wire. Solid Male 1/2 inch NPT thread on both ends. (Item #: 179906, Ref: H42-2M-180) $55.50

Hydraulic Hose Assembly-NPT, 24 inch - Universal. 1/2 inch I.D. double wire braid (SAE-2R) with 1/2 inch NPT solid male fittings both ends. 24 inch overall length. Replaces OEM # - 407435R1. (Item #: 118256, Ref: H42-2M-24) $14.10

Hydraulic Hose Assembly-NPT, 30 inch - Universal. 30 inch overall length. 1/2 I.D. 2 Wire. Solid Male 1/2 NPT thread on both ends. (Item #: 118259, Ref: H42-2M-30) $16.10

Hydraulic Hose Assembly-NPT, 48 inch - Universal. I.H.C.: 1/2" I.D. double wire braid (SAE-2R) with 1/2" NPT solid male fittings both ends. 48" overall length. Replaces OEM # - 407437R1. Hydraulics: 48 inch overall length (Item #: 118261, Ref: H42-2M-48) $16.50

Hydraulic Pump Drive Flange - The bolt holes on the flange are 5/16 inches diameter and 2.250 center to center. This is used on a drive shaft that is 3/4 inches in diameter with a key way and set screw. This part replaces 1753730M1, 192199, 192199GV, L367GV, L36-7GV, 1753730M1GV, 1753730M91, L367. It is part of a 352 series Morflex Coupler. (Item #: 128567, Ref: 192199) $21.10

Hydraulic Pump for Loader - Part Description: Pump, Hydraulic For 730 LOADER, 735 LOADER. SPECS: CAPACITY GPM at RPM: 21.5 at 2000, SHAFT DIAMETER: 7/8 inch, SHAFT TYPE: 13 spline, ROTATION: Left hand, PORT SIZE INLET: 1-5/8 inches-12 ORB, PORT SIZE OUTLET: 1-5/16 inches-12 ORB, MOUNTING: 2 bolt SAE "B", FORD PUMP APPLICATION: 730 and 735 loaders, CAPACITY GPM at RPM: 21.5 at 2000, SHAFT DIAMETER: 7/8 inch, SHAFT TYPE: 13 spline, ROTATION: Left hand, MOUNTING: 2 bolt SAE "B", INLET: 1-5/8 inches-12 ORB, OUTLET: 1-5/16 inches-12 ORB. The 2 bolt mount slots are 9/16 inch and open on the ends. Minimum measurement between the slots are 5 1/4 inches and Maximum is 6 7/8 inches. (Item #: 127269, Ref: 7702425-29Z) $780.00

Hydraulic Pump, Front Mounted - This Hydraulic Pump is used with some 701, 702 and 703 Loaders. It is 14 Gallons Per Minute at 2000 RPM. The shaft is 3/4 inch round with a key way. Left Hand Rotation. Inlet is 1 Inch NPT. Outlet is 3/4 Inch NPT. Mounting bolt spacing 4 3/16 inches center to center. Comes with two adapters. Contains: 1-720FSO-3/4X3/4 HC4008 adapter, 1-720FSO-1X1-1/4 HC4009 adapter. This Pump may work in other loader application. Verify Specs before ordering. (Item #: 182700, Ref: L827-10X-LB) $600.00

Hydraulic Valve Kit - Valve with handles, three-spool, 2000 p.s.i. Relief, all spools tandem (4-way) spring center to neutral. (Item #: HV4030) $787.98

LBP Coupler Center - Center member. Center member. 3-5/8" O.D., four 5/16" holes, 2-1/4" bolt circle (L52-10) For tractor models 352. (Item #: 178931, Ref: 192169) $75.00

LBP Hydraulic hose Assembly - Hydraulic hose assembly. For Ford model 740 LOADER. (Item #: 179521, Ref: 7701142) $30.30

Morflex Center Member - This is a 1-302 Morflex Center member. It measures 3-1/8 inch diameter, four 1/4 inch holes, 1-15/16 inch bolt circle. Replaces part numbers 893129, 191192, L5227, 1506097M91, 1086870M1, 191192LBP, 1752218M91, L52-27 (Item #: 116952, Ref: 191192LBP) $49.00

Top Link, Hydraulic - FORD: Hydraulic top link cylinder. All ports 9/16 inch-18 O-ring boss with two adapters 9/16 inch-18 ORBM x 1/4 inch NPTM 90 degree swivel. 3 inch cylinder bore, 8 inch stroke length, 26 inch closed length, 12-7/16 inch barrel length, 1 inch rod end diameter, 1-3/4 inch rod end width, 1 inch diameter base end. (Item #: 167145, Ref: HTL3103) $270.00

Universal Pressure Gauge, Hydraulic - 1000 Lb. Gauge. Glycerin Filled. Stainless Steel Case 2-1 2 diameter. Nickel silver movement accurate to within 2%. Dual range KPA-PSI. Plexiglass crystal. 1 4 NPT male brass fitting. (Item #: 172285, Ref: GG1000) $13.50

Universal Pressure Gauge, Hydraulic - 60lb Gauge. Glycerin Filled. Stainless Steel Case 2-1/2 diameter. Nickel silver movement accurate to within 2%. Dual range KPA-PSI. Plexiglass crystal. 1/4 NPT male brass fitting. (Item #: 172338, Ref: GG60) $13.91

Implements

Axle Bolt - Axle bolt, 1 each (Ref 3). Used on many Bush Hog rotary cutters. Used on models 12, 104, 105, 109, 126, 205, 255, 275, 285, 305, 306, 307, 405, 405HR, 406, 406HR, 502, 600, 1050, 1051, 1109, 1126, 1207, 1209, 1226, 1306, 1307, 1405, 1406, 2510, 2512, 3108, 2309, BD90, FH162, S268, SM60, SQ36 (Item #: 170217, Ref: BH1317) $14.90

Bearing cone (L44643) - For Caster Assembly, requires 2.Used on many Bush Hog rotary cutters. Used on models 12, 104, 105, 109, 126, 205, 255, 275, 285, 305, 306, 307, 405, 405HR, 406, 406HR, 502, 600, 1050, 1051, 1109, 1126, 1207, 1209, 1226, 1306, 1307, 1405, 1406, 2510, 2512, 3108, 2309, BD90, FH162, S268, SM60, SQ36, SQ480, SQ600. (Item #: 114630, Ref: 22) $5.90

Bearing Cup - This part fits Caster Assembly (Part Number BH215, Ref #6). Sold individually, two used per caster assembly. Used on many Bush Hog rotary cutters. Used on models 12, 104, 105, 109, 126, 205, 255, 275, 285, 305, 306, 307, 405, 405HR, 406, 406HR, 502, 600, 1050, 1051, 1109, 1126, 1207, 1209, 1226, 1306, 1307, 1405, 1406, 2510, 2512, 3108, 2309, BD90, FH162, S268, SM60, SQ36. Also replaces 132709, 15191, 32190M1, L44610. (Item #: 169771, Ref: 170BH) $7.86

Caster Assembly - Tail wheel and hub assembly with grease fitting and fork assembly uses 1 1/2 inch diameter shaft. Shaft on Yoke is 1-1/2 inches diameter, 8 inches overall length, 7-1/4 inch to pin hole. New style tail assembly, used on the following Bush Hog cutters: 12, 104, 105, 109, 126, 205, 255, 275, 285, 305, 306, 307, 405, 405HR, 406, 406HR, 502, 600, 1050, 1051, 1109, 1126, 1207, 1209, 1226, 1306, 1307, 1405. Wheel must be attached to fork. For Bush Hog cutters with SPB40 spacer (included), assembly will also replace all models with Timken bearings. (Item #: 173612, Ref: 12269) $183.00

Caster Assembly, Old Style - Tail Wheel and Hub Assembly with grease fitting. 4 x 8 inch rim, 15 inch outside diameter of wheel. Includes wheel, hub, axle bearing and bolt assembly. OLD style tail assembly used on the following Bush Hog cutters: 12, 104, 105, 109, 126, 205, 255, 275, 285, 305, 306, 307, 405, 405HR, 406, 406HR, 502, 600, 1050, 1051, 1109, 1126, 1207, 1209, 1226, 1306, 1307, 1405, 1406, 2510, 2512, 3108, 2309, BD90, FH162, S268, SM60, SQ36, SQ480, SQ600. Wheel must be attached to fork. For Bush Hog cutters. With SPB40 spacer, assembly will also replace all models with Timken Bearings (Ref #1-#11). (Item #: 161111, Ref: BH215) $132.00

Hub Assembly - Hub with bushings (3/4 inch), wheel bolts (4), and grease fitting. Center tube length 5 inches. For rotary cutters: RB60 with new style 1-1/4 inch diameter caster, SM60R, SM160R; Squealer models: 1207, SQ36, SQ48, SQ60, SQ72, SQ148, SQ480. Replaces 60978, 60990, 63812. Can use 500BH tail wheel. (Item #: 180514, Ref: 63813BH) $38.10

Hub with Bearing Cups - 4-bolt, 5 inch bolt circle and 3-5/8 inch wheel pivot hub with bearing cups (1 inch axle) (Ref #5). This part fits caster assembly (part number BH215). Used on many Bush Hog rotary cutters. Used on models 12, 104, 105, 109, 126, 205, 255, 275, 285, 305, 306, 307, 405, 405HR, 406, 406HR, 502, 600, 1050, 1051, 1109, 1126, 1207, 1209, 1226, 1306, 1307, 1405, 1406, 2510, 2512, 3108, 2309, BD90, FH162, S268, SM60, SQ36. (Item #: 182627, Ref: BH1311) $49.30

No
Picture
Round Bale Tine 31.5 Inches - Fully Hardened. Also replaces Kverneland 221151. (Item #: 182589, Ref: 221129) $51.00

No
Picture
Round Bale Tine 38.5 Inches - Fully Hardened. Also replaces Kverneland 241107, 241161. (Item #: 182592, Ref: 241100) $91.48

No
Picture
Round Bale Tine 43 Inches - Fully Hardened. (Item #: 182594, Ref: 241166) $111.54

No
Picture
Round Bale Tine 49 Inches - Fully Hardened. (Item #: 152690, Ref: 241162) $78.00

No
Picture
Round Bale Tine 55 Inches - Fully Hardened. (Item #: 182593, Ref: 241163) $131.61

Seal, Caster - Seal, 2 required (Ref #2). Used on many Bush Hog rotary cutters. Used on models 12, 104, 105, 109, 126, 205, 255, 275, 285, 305, 306, 307, 405, 405HR, 406, 406HR, 502, 600, 1050, 1051, 1109, 1126, 1207, 1209, 1226, 1306, 1307, 1405, 1406, 2510, 2512, 3108, 2309, BD90, FH162, S268, SM60, SQ36, SQ480, SQ600. (Item #: 180300, Ref: 30BH) $4.30

Tail Wheel Assembly - 4 inch x 8 inch tail wheel assembly with laminated tire. 3-5/8 inch pilot, 4 bolt holes, 5 inch bolt circle, 3-3/4 inches wide, 15 inch outside diameter. Used on the following Bush Hog cutters: 12, 104, 105, 109, 126, 205, 255, 275, 285, 305, 306, 307, 405, 405HR, 406, 406HR, 502, 600, 1050, 1051, 1109, 1126, 1207, 1209, 1226, 1306, 1307, 1405 and 1406, 2510, 2512, 3108, 3209, BD90, FH162, S268, SM60, SQ36, SQ480, SQ600. Replaces Sidewinder 15205, Servis Rhino 373024H, Terrain King 373024H, Modern 401-0048, BMB 5337, Hardee C40-RC, King Kutter KK4X8. (Item #: 111222, Ref: 500BH) $56.00

No
Picture
Talc Powder Lubricant - Dry Talc powder lubricant, 8 lb container. Absorbs moisture and keeps treated seed from sticking together in planter boxes. Recommended application rate: 3 oz. Coverage: Typically treats 60-80 acres. (Item #: 107928, Ref: TP19000TP) $22.10

Lights

Headlight Assembly, 12 Volt - (Single) Headlight Assembly 12-volt, blue - Sealed beam headlamp assembly in heavy gauge steel housing with Rubber bezel. Does not look like original. (Item #: 184496, Ref: L525HB-12V) $53.00

Light Switch with Knob - Universal switch, for 6 volt tractors. Verify style is correct for your model. (Item #: 114720, Ref: AA4667R) $16.60

Portable Halogen Work Lamp - 3 inch x 5 inch sealed beam unit, 12 volt, 50 watt, 4 amp. With handle and magnetic base. Projects flood beam pattern 50 foot wide x 30 foot long. Lamp is not legal for street use. (Item #: L200MAGH) $75.13

No
Picture
Sealed Beam Bulb, 12 Volt - Red/white combination work/tail light, 4-1/2 inch diameter. (Item #: 116014, Ref: S.52670) $23.50

Tail Light Lens - Plastic 4 inch lens for DUOLAMP with FOMOCO stamped on lens (has 2 mounting screw holes spaced 3 1/8 inches apart). Fits tractors 1953 and newer. (Item #: 178144, Ref: FDV13450A) $16.50

Miscellaneous

Deluxe Canopy, 3 Bow - This universal Blue 3-Bow Deluxe Canopy comes with bows and cover. Universal brackets sold separately. Fender mounting kit is part number 6A216. Axle Mounting Kit is part number 6A217. Measures about 48 inch spread from Mounting brackets (40 inch spread at the top of canopy) Height is approximately 31 inch. (Item #: 178876, Ref: RFC100B) $245.00

Hand Cleaner, Gallon - Hand cleaner, with dispenser pump. 1 gallon plastic bottle. (Item #: 180453, Ref: PRM25218) $24.60

Tractor Umbrella with Frame & Mounting Bracket - Blue - Complete umbrella consisting of a cover, bracket and frame, 54" x 54" cover made of 10 oz. duck canvas with leather reinforcements and steel grommets, Metal parts are zinc-coated for long-lasting, maintenance-free service, Rigid framework for cover is built to withstand farm and industrial use, Installs easily, folds down for trailering and removes in seconds without Additional Handling & Oversize Fees Apply To This Item, tools, (Item #: 161190) $123.00

Paint

44 Minute DVD - How to Paint a Tractor - This DVD demonstrates the entire painting process including sanding, priming, body work, painting and decals. A John Deere B is used as the sample tractor, but the information will pertain to any make or model - the techniques are the same. Safety is also discussed. (Item #: 183950, Ref: JDV-02250) $24.00

No
Picture
Paint, Aluminum, Spray Can - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100244, Ref: TP312SP) $8.50

No
Picture
Paint, Brownish Medium Gray, 1 Quart - Ford Brownish Medium Gray was used for the same applications as TP240Ford Medium Gray. This is a lighter shade. Since the tractors did not come off the production line all the same, the darker or light shades are completely up to the desires of the customer. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 184575, Ref: TP245QT) $50.00

No
Picture
Paint, Clear Coat, 1 Gallon - From Tallmans, formulated by Van Sickle, providing OEM quality. High strength air dry Acrylic laquer. Protects the original paint finish, adds more shine, prolongs color and prevents fade. Water clear non-yellowing gloss coat, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 108409, Ref: TP447GAL) $65.00

No
Picture
Paint, Clear Coat, 1 Quart - From Tallmans, formulated by Van Sickle, providing OEM quality. High strength air dry Acrylic laquer. Protects the original paint finish, adds more shine, prolongs color and prevents fade. Water clear non-yellowing gloss coat, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 108408, Ref: TP447QT) $30.00

No
Picture
Paint, Empire Blue, 1 Gallon - This Ford Empire Blue is High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. For tractor models 1962 and up. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100713, Ref: TP360GAL) $57.00

No
Picture
Paint, Empire Blue, 1 Quart - This Ford Empire Blue is High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. For tractor models 1962 and up. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100712, Ref: TP360QT) $24.00

No
Picture
Paint, Empire Blue, Spray Can - This Ford Empire Blue is High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. For tractor models 1962 and up. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100711, Ref: TP360SP) $7.70

No
Picture
Paint, Ford White, 1 Gallon - High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 108135, Ref: TP470GAL) $86.00

No
Picture
Paint, Ford White, Spray Can - High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 108133, Ref: TP470SP) $10.60

No
Picture
Paint, Gloss Black, 1 Gallon - High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100116, Ref: TP550GAL) $53.00

No
Picture
Paint, Gloss Black, 1 Quart - High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100115, Ref: TP550QT) $24.00

No
Picture
Paint, Gloss Black, Spray Can - High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100114, Ref: TP550SP) $8.70

No
Picture
Paint, Gray Primer, 1 Quart - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100121, Ref: TP2700QT) $22.40

No
Picture
Paint, Gray Primer, Spray Can - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100120, Ref: TP2700SP) $8.30

No
Picture
Paint, Industrial Yellow, Spray - High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics.Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100723, Ref: TP760SP) $8.50

No
Picture
Paint, Light Gray, 1 Gallon - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. For tractor models 1965 and up. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100716, Ref: TP330GAL) $57.00

No
Picture
Paint, Light Gray, 1 Quart - OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. For tractor models 1965 and up. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100715, Ref: TP330QT) $21.40

No
Picture
Paint, Light Gray, Spray Can - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. For tractor models 1965 and up. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100714, Ref: TP330SP) $9.10

No
Picture
Paint, Medium Gray, 1 Quart - This Ford Medium Grey was used from 1948 through 1965 on models 8N, NAA, Jubilee, 600, 700, 800, 900, 501, 601, 701, 801, 901 and Super Major. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Used on 1948 to 1965 tractors. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100718, Ref: TP240QT) $22.00

No
Picture
Paint, Medium Gray, Spray Can - This Ford Medium Grey was used from 1948 through 1965 on models 8N, NAA, Jubilee, 600, 700, 800, 900, 501, 601, 701, 801, 901 and Super Major. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Used on 1948 to 1965 tractors. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100717, Ref: TP240SP) $8.50

No
Picture
Paint, Red Primer, 1 Gallon - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100119, Ref: TP3987GAL) $59.00

No
Picture
Paint, Red Primer, 1 Quart - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100118, Ref: TP3987QT) $24.00

No
Picture
Paint, Satin Black, 1 Quart - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics.Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100254, Ref: TP225QT) $24.00

No
Picture
Paint, Satin Black, Spray Can - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics.Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100253, Ref: TP225SP) $8.50

No
Picture
Paint, Vibrant Blue, 1 Gallon - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 156586, Ref: TP365GAL) $90.00

No
Picture
Paint, Vibrant Blue, 1 Quart - OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 156587, Ref: TP365QT) $35.00

No
Picture
Paint, Vibrant Blue, Spray Can - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 156585, Ref: TP365SP) $10.00

No
Picture
Paint, Yellow Primer, 1 Gallon - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 184741, Ref: TP2720GAL) $84.67

No
Picture
Slip Resistant Coating - Gallon can. For use in a variety of applications where slip resistance or sound deadening qualities are desired. Moisture and chemical resistant, helps protect against corrosion. Ready to use as is for easy application and touch up with brush or roller. Coverage area is 75 to 100 square feet. (Item #: BL116GAL) $68.39

No
Picture
Slip Resistant Coating Kit - Do it yourself kit. Comes with one gallon of liner, mini roller with tray, two replacement roller covers, 2" brush, and sanding sponge. For use in a variety of applications where slip resistance or sound deadening qualities are desired. Moisture and chemical resistant, helps protect against corrosion. Ready to use as is for easy application and touch up with brush or roller. Coverage area is 75 to 100 square feet. (Item #: BL116KIT) $99.22

Tire Paint, Black - Black tire paint (1 Gallon)- The best way to make tires look like new. Our paint is a permanent water based paint that applies easily and dries quickly. It will not rub off even when wet. Gives dull, faded tires a non-glossy, like new finish. This paint is READY TO USE. (Item #: 185598, Ref: E844R) $40.01

PTO / Driveline

Driveline Assembly with Yokes - AB4 series, complete drive shaft assembly with shielding and tractor and implement yokes. 1-3/8 inch 6 spline Q.D. tractor yoke. 1-3/8 inch round bore with 1/2 inch pin hole implement yoke. 1300 mm (51 inch) overall length end of yoke to end of yoke. 1110 mm (43-3/4 inch) compressed length center to center of cross bore. Cross and bearing kit, 27 mm 1.063 (1-1/16 inch) bearing diameter x 74.6 mm 2.940 (2-15/16 inch) overall length (43-3/4 inch). Verify length before ordering. (Item #: 180775, Ref: AB4111WY) $174.00

Driveline Assembly with Yokes - AB4 series, complete drive shaft assembly with shielding and tractor yoke, ratcheting torque limiter on implement end. 1-3/8 inch 6 spline Q.D. tractor yoke, 1-3/8 inch 6 spline ratcheting torque limiter with quick disconnect on implement end. 1372 mm (54 inch) overall length end of yoke to end of clutch. 1110 mm (43-3/4 inch) compressed length center to center of cross bore. Cross and bearing kit 27 mm 1.063 (1-1/16 inch) bearing diameter x 74.6 mm 2.940 (2-15/16 inch). 1372 mm (54 inch) overall length ***VERIFY LENGTH BEFORE ORDERING*** (Item #: 124815, Ref: AB4111K33) $339.00

NOTE

PTO Adapter - PTO adapters are located under the PTO category in the Accessories and Universal Parts section.

NOTE

PTO Overide Clutch - This 6 spline Override Coupler converts a 1 1/8 inch diameter PTO shaft to 1 3/8. It has a 1 1/8 inch female at one end and 1 3/8 inch male at the other end). Free-wheels smoothly when implement exceeds PTO speed. WARNING: The use of PTO adapters can be hazardous if not used with adequate protection such that ASABE standard S318.16 requires suitable shielding be provided for any device intended for installation between the tractor PTO shaft and the implement input driveline. (Item #: 103169, Ref: C670F) $46.60

PTO Overide Clutch - Override coupler for 1 3/8 inch female to 1 1/8 inch male, 6-spline. Free-wheels smoothly when implement exceeds PTO speed. WARNING: The use of PTO adapters can be hazardous if not used with adequate protection such that ASABE standard S318.16 requires suitable shielding be provided for any device intended for installation between the tractor PTO shaft and the implement input driveline. (Item #: 191020, Ref: C680F) $76.00

PTO Overide Clutch - Override coupler for 1 1/8 inch female to 1 1/8 inch male, 6-spline. Free-wheels smoothly when implement exceeds PTO speed. WARNING: The use of PTO adapters can be hazardous if not used with adequate protection such that ASABE standard S318.16 requires suitable shielding be provided for any device intended for installation between the tractor PTO shaft and the implement input driveline. (Item #: 103167, Ref: C690F) $76.00

PTO Safety Clutch, 40 HP - 1-3/8 inch 6 spline male and female ends, 6 inch diameter, 40 horse power capacity. Heavy duty unit allows PTO driven implements to freewheel with adjustable safety protection under load. Prevents expensive damage to internal tractor PTO packs. Prevents single clutch tractors from being driven forward by PTO over-run. (Item #: 183648, Ref: B9164) $268.00

Seats

Seat, Air Suspension, Black Leatherette, Universal - Seat, Deluxe AG Air suspension, Includes 12 volt compressor. Slides, fore/aft and lateral isolators, adj shock, seat top with Black Leatherette upholstery, lumbar, recline tilt up and angle adjust armrests. *Adjustable backrest recline. *Infinitely adjustable mechanical lumbar support *Heavy duty 12 volt air compressor included. *DOUBLE LOCKING SLIDES, fore and aft isolators with lockout. *Ride firmness adjustment *Weight range 110-330 lbs. *** CALL FOR FREIGHT QUOTE *** (Item #: TS5056V) $1518.86

Seat, Air Suspension, Cloth, Universal - Seat, Deluxe AG Air suspension, Includes 12 volt compressor. Slides, fore/aft and lateral isolators, adj shock, seat top with gray cloth upholstery, lumbar, recline tilt up and angle adjust armrests. * Trimmed in FabriForm cloth, can be punctured with pens and screwdrivers and will not tear. *Adjustable backrest recline. *Infinitely adjustable mechanical lumbar support *Heavy duty 12 volt air compressor included. *DOUBLE LOCKING SLIDES, fore and aft isolators with lockout. *Ride firmness adjustment *Weight range 110-330 lbs. *** CALL FOR FREIGHT QUOTE *** (Item #: TS5056) $2161.57

Seat Cushion, Black - Cover with piping and Ford script logo. Fits all 1939-1964 models with a 17 inch wide steel seat pan. (Item #: 115058, Ref: 8N401BLK) $37.90

Tie-On Seat Cover - Blue and White, 19 inches wide. Deluxe with 2 inches of foam. (Item #: 101353, Ref: R1013) $31.30

Universal Seat - Color: Yellow - Universal Application Leatherette Suspension seat. For most Compact, Agricultural and Industrial Tractors. Adjustable base for 5 different mounting angles, Internal Suspension Weight Adjustment, Special Slotted Base for mounting holes adjustments of approximately 2-1-2 inches forward/rear, Adjustable Slide Track. IMPORTANT: THESE SEATS FIT MOST TRACTORS, BUT NOT ALL. PLEASE LOOK CLOSELY AT THE DIMENSIONS ON THE PICTURE BEFORE ORDERING TO BE SURE IT WILL FIT YOUR TRACTOR. Color is John Deere Yellow. (Item #: 101375, Ref: TS1040ATSP) $100.00

Sheet Metal / Body Parts

Cab Foam Kit Spray Adhesive - 1 16 Oz. can will attach most kits. Large, multi piece kits may need 2 cans. (Item #: 165963, Ref: R0140) $41.19

Pilot Punch Set - Set contains 12 sizes one of each 1/16, 3/32, 1/8, 5/32, 3/16, 7/32, 1/4, 5/16, 3/8, 7/16 and 1/2. (Item #: 186563, Ref: RPD112K) $173.00

Steering

Power Steering Pump Pulley - This Power Steering Pump Pulley is used with S03-1003 Power Steering Pump. It is designed for Tractors using Eaton Style power steering pump. It is made of Stamped steel. Measures 5 inches outside diameter, 0.675 inch bore, 1/8 inch keyway, 0.9715 inch total width for 1/2 inch belt. (Item #: 164438, Ref: ABC1417) $47.60

Steering Wheel Spinner Assortment - Complete wheel spinner assortment: includes 2 blue, 2 green, 3 red, 2 yellow and 3 black. (Item #: 185079, Ref: WSV125A) $128.00

Tie Rod Boot Assortment - Includes 6 Tie Rod Boots. Two each of the following sizes: 1 13/16 inches x 5/8 inch x 5/8 inch, 1 15/16 inches x 3/4 inch, 3/4 inch, and 1 3/8 inches x 1 inch x 1/2 inch. (Item #: 183427, Ref: TIERODBOOTS) $13.00

Tools

No
Picture
Blade Fuse Assortment - With 6-24 volt tester light and fuse puller. Contains 93 pieces. 5, 10, 15, 20, 25 and 30 amp blade type fuses. (Item #: 183798, Ref: S.29891) $23.10

No
Picture
Hay Moisture Tester - Self Calibrating Electronic Moisture Tester. (Item #: 180261, Ref: S.58474) $287.00

Tractor Manual Search - Yesterday's Tractor Co.

Wheels

Front Rim - This is a 6 inches x 16 inches Front Wheel Rim. It has a pilot hole of 4.625 inches. It uses 6 bolts in a 6 inch bolt pattern. Back-spacing is 4.75 inches. Verify size of old rim before ordering. (Item #: 103768, Ref: FW60166) $92.00

Front Rim - This is a 5.5 inch x 16 inch Front Wheel Rim. It has a pilot hole of 4.625 inches. It uses 6 bolts in a 6 inch bolt pattern. Back-spacing is 4.75 inches. Capacity of 3500 lbs based on 20 MPH max speed. Verify size of old rim before ordering. Replaces AL82488, A38404, C7NN1007J, D2NN1007N, D2NN1007S, D8NN1007BA, E1ADDN1015B, E1ADKN1015A, E6NN1007BA, G57046, K914312, K921475, K947941, VPH6001, 1660769M1, 1678319M91, 1678319M92, 1691618M92, 1691618R92, 1883333M92, 3114166R91, 509893M1, 509893M91, 57512110, 70000-00028, 751734R91, 82005056, 83900159, 83954658, 83960327, 9A306 (Item #: 116854, Ref: FW55166) $78.00

Tire Inner Tube - This Inner Tube fits 4.00 x 15, 5.00 x 15, 5.90 x 15, 4.50 x 16 and 5.00 x 16 tires. It has a TR-15 valve stem. Valve height 1.38 inch, diameter 0.65 inch. (Item #: 118299, Ref: 500X15TB) $17.15

Tire Tube - For 5.50 inch, 6.00 inch, or 6.50 inch X 16 inch tires. This is a bias style tube, not for radial tires. Not for recreational use. (Item #: 118295, Ref: WHS050) $19.10

No
Picture
Tire Tube 28 Inch - This 28 inch tire tube is used for all tractors with the following tires: 10.00 inch x 28 inch, 11.00 inch x 28 inch, 11.2 inch x 28 inch and 12.4 inch x 28 inch. (Item #: 158249, Ref: WHS058) $64.00

No
Picture
Tire Tube 32 Inch - This 32 inch tire tube is used for all tractors with the following tires: 7.00 inch x 32 inch, 8.00 inch x 32 inch, 9.00 inch x 32 inch and 9.5 inch x 32 inch. (Item #: 184736, Ref: WHS062) $67.00

No
Picture
Tire Tube 38 Inch - This 38 inch tire tube is used for all tractors with the following tires: 10.00 inch x 38 inch, 11.00 inch x 38 inch, 11.2 inch x 38 inch and 12.4 inch x 38 inch. (Item #: 183819, Ref: WHS064) $82.00

Wheel Clamp - Wheel clamp holding disc to rim for double ramp type on power adjustable rims. For 28 inch rim on tractors 2000, 3000, 4140, (10-1968 to 1975); 2600, 3600, 4100, 4600SU except Baseldon models, (1981 to 3-1990); 3230, 3430, 3930, 4130, 4630, 4830LCG, (3-1990 to -) Use with rims PAR10X18 and C5NN1050J and C5NN1050H. Also replaces 3615259M1, 70235676 and 7000000241, E5NN1043AA. (Item #: 124526, Ref: 898021M1) $18.20

Wheel Front 8X16 - Front Wheel 8 inch x 16 inch ; 6 bolt, 6 inch circle, 4.62 inch pilot. (Item #: 180445, Ref: D5NN1007A) $112.00