International Harvester / Farmall 595 Tractor Parts

[Categories]   [All Farmall Models]   [Print]  

Brakes
Brake Disc - 10.190 inch outside diameter, 15 internal splines. For tractor models Used on International models 2400, 2400A, 248, 2500, 2500A, 268, 3220, 3230, 380B, 385, 395, 4210, 4230, 4240, 454, 464, 474, 484, 485, 495, 574, 584, 595, 674, 684, 685, 695, 784, 884, 885, 895, 995, C100, C50, C60, C70, C80, C90, CX100, CX50, CX60, CX70, CX80, CX90, Hydro 84. Replaces 1027256C1, 114621C1, 114622C2, 399734R1 (Item #: 105452, Ref: 114622C2) $94.00
Brake Master Cylinder - This Brake Master Cylinder Rod is 3/8 inch x 24 pitch thread. It is used on 3220, 3230, 4210, 4230, 4240, 485XL, 5.9L Engine, 5120, 5130, 5140, 5220, 5230, 5240, 5250, 585XL, 595, 685, 695, 785XL, 856XL, 885, 885XL, 895, 995, CX100, CX50, CX60, CX70, CX80, CX90, MX100, MX100C, MX110, MX120, MX135, MX80C, MX90C. Replaces 1287734C92, 226301A1, 3129643R91. (Item #: 122351, Ref: 1287734C92) $64.00
Brake Master Cylinder - This Brake Master Cylinder is used on IH Tractors: 3220, 3230, 385, 395, 4210, 4230, 4240, 485, 495, 595, 685, 695, 885, 895, 995, C100, C50, C60, C70, C80, C90. It Replaces original part number 1287843C92 (Item #: 124544, Ref: 1287843C92) $90.00
Brake O-Ring Kit - For tractor models 385, 395, 454, 464, 484, 485, 495, 574, 584, 585, 595, 674, 684, 685, 695, 784, 884, 885, 895. Set of 6 O-Rings, 2 for brake piston, 4 for differential bearing carriers. (Item #: 105424, Ref: 539535R91) $35.50
Brake Plate - The measurements on the Brake Plate are ID: 8 1/8 inches (206mm) with 3 tabs, OD: 10 1/4 inches (259mm). This part replaces 399736R3, 984439C1. Used on International models 2400, 2400A, 248, 2500, 2500A, 268, 3220, 3230, 380B, 385, 395, 4210, 4230, 4240, 454, 464, 474, 484, 485, 495, 574, 584, 595, 674, 684, 685, 695, 784, 884, 885, 895, 995, C100, C50, C60, C70, C80, C90, CX100, CX50, CX60, CX70, CX80, CX90, Hydro 84 (Item #: 105456, Ref: 399736R3) $84.77

Clutch
No Picture Clutch Alignment Tool - 1-1/8 inch 10 spline, 1-5/8 inch 10 spline, 3/4 inch pilot. For tractor models 364, 384, 385, 395, 494, 574, 584, 585, 595, 895, 995, 3230, 4210, 4220, 2400A, 2400B, (424, 2444 with single disc), 2500A, 2500B, 3500, 3500A. (Item #: 113942, Ref: S.70912) $26.50
Clutch Kit - This New Clutch Kit, includes 537290R91 pilot bearing, 158125C91 release bearing, 85025C2 pressure plate-10 spline, 1 5/8 inch hub-12 inch diameter, 85026C3R clutch drive disc-10 spline with 1 1/8 inch hub and 10 spline-1 1/8 inch by 10 spline 1 5/8 inch pilot tool. Fits 3210 PATRIOT, 3220, 3230, 380B LOADER, 4210, 4220, 4230, 4240, 495, 584, 585, 595, 684, 685, 695, 784, 786, 795, 884, 885, 895, 985, 995. (Item #: 115343, Ref: 1712-7070) $400.00
Pressure Plate Assembly, 12 Inch - This is a 12 inch, 10 spline with 1 5/8 inch center hub pressure plate. It is used on 3210 Patriot, 3220, 3230, 380B Indust/Const, 4210, 4220, 4230, 4240, 495, 584 Indust/Const, 595, 684, 685, 695, 784, 795, 884, 885, 895, 985, 995. Replaces 84342556, 85025C2, 85025C2R. (Item #: 110580, Ref: 85025C2) $168.00
PTO Clutch Kit - Clutch disc kit for single or dual speed independent PTO using 5 discs and 8 plates. Tractors: Hydro 84, 385, 395, 464, 484, 485, 495, 574 serial number 100001 and up, 84, 585, 595, 674, 684, 684, 685, 695, 784, 885, 2400A serial number 100001, 2500A serial number 100001 and up. For 2400A, 2500A, 385, 395, 464, 484, 485, 495, 574, 584, 585, 595, 634, 674, 685, 695, 784, 884, 885, HYDRO 84. Kit includes, 5 DISCS (401716R2), 8 PLATES (66188C1), 1 O-RING (401723R1), 1 O-RING (401724R1), 6 SPRINGS (66182C1). (Item #: 124694, Ref: 66193C91) $144.00
Release Bearing Carrier - This Release Bearing Carrier is used with 398342R2. Used on 495, 595, 695, 895, 995 Tractors. Replaces original part number 1971045C1 (Item #: 162403, Ref: 1971045C1) $51.00
Release Bearing Carrier - This Release Bearing Carrier is used with 398342R2 in 12 inch clutch systems. 495, 595, 695, 895, 995. Replaces 1970934C1, 1970934C2 (Item #: 162402, Ref: 1970934C1) $39.20

Cooling System
Fan, 5 Blade - For tractor models 380B, 385, 395, 484, 485, 495, 574, 584, 595, 674, 684, 685, 695, 784, 884. (Item #: 124624, Ref: 1275810C1) $142.00
Fan, 6 Blade - 17.75 inch diameter, 1.25 inch pilot hole, 1.375 inch center to center on mounting holes. For tractor models (595, 685, 695, 885, 895 all diesel with AC). (Item #: 124626, Ref: 84416C1) $135.00

Drive Train
Torque Amplifier Clutch Kit - Power shift, 6 friction plates, 4 steel plates, 2 piston seals. For tractor models 684, 784, 884, 485, 585, 685, 885, 395, 495, 595, 695, 895, 995, 4210, 3220, 3230, 4230, 4240, C50, C60, C80, C90, C100. Replaces 401717R3, 401724R1, 402571R1. (Item #: 124618, Ref: 401716R3) $151.00

Electrical System
Alternator - 12 volt, 45 amp. For tractor models (1494 engine SN# 11430950 and up), 1594, 1694, 4210, 4230, 4240, 495, 595, 695, 895. (Item #: 156095, Ref: 92293C1) $133.00
Ignition Switch - This ignition kit with keys is used on multiple Case/IH tractors with Cabs and Digital Dashes. It replaces original part numbers 1987424C1, 1533738C1 and A187614. For tractor models 3210, 3220, 3230, 385, 395, 4210, 4220, 4230, 4240, 440, 485, 495, 5120, 5130, 5140, 5150, 5220, 5230, 5240, 5250, 540, 585, 595, 640, 685, 695, 740, 743, 745, 785, 795, 840, 844, 845, 856, 885, 895, 940 and 995. (Item #: 164183, Ref: 1987424C1) $40.70
Starter - STARTER For 385, 395, 484, 485, 495, 584, 585, 595, 684, 685, 695, 784, 884, 885, 895, 995 Replaces Lucas 27508B (Item #: 104180, Ref: 537140R96) $174.47
Starter Drive - Clockwise rotation, 10 teeth. Fits Lucas 26428A and Magnetti Marelli starters. For tractor models Hydro 84, 385, 395, 484, 485, 495, 584, 585, 595, 684, 685, 695, 784, 884, 885, 895, 995, 3220, 3230, 4210, 4230, 4240. (Item #: 112574, Ref: 84209C2) $25.20
Starter Motor - Fits 454, 474, 574, 674, 484, 584, 684, 784, 884, 6858, 485, 485XL, 585, 585XL, 685, 685XL, 785, 785X, 885, 885XL, 985XL, 395, 495, 495XL, 595, 595XL, 695, 695XL, 795, 795XL, 895, 895XL, 995XL, 2310, 3220, 3230, 4210, 4220, 4230, 4240, 84 Hydro. Replaces these starter numbers in the above models: B514002, SLU0013, TS-1212, TS-4030, 1107867, 114568A1, 114568A2, 114568A3, 189330A5, 1998343, 230428A1, 230428A3, 537140R91, 537140R96, SDR0214. (Item #: 104180, Ref: 537140R95) $174.47
Starting Button - Attaches with spade terminals. For tractor models 1026, 385, 395, 444, 454, 464, 484, 485, 495, 544, 574, 584, 585, 595, 664, 666, 674, 684, 686, 706, 756, 766, 784, 786, 806, 826, 856, 884, 886, 966, 986, 1066, 1086, 1206, 1256, 1456, 1466, 1468, 1486, 1566, 1568, 1586, Hydro 70, Hydro 86, Hydro 100, Hydro 186, 2400A, 2500A, 3088, 3288, 3388, 3488, 3588. Replaces IHS800. (Item #: 112232, Ref: 397940R93) $7.40

Engine Bearings
Rod Bearing Standard - This is a single rod bearing for International Engines: D155, D179, D206, D239, D246, D268, D310, D358. Replaces 3055218R1. Order on for each connecting rod. (Item #: 191598, Ref: CRK239D) $7.00

Engine Gaskets
No Picture Head Gasket Set - For 584, 585, 595 with D206 Diesel Engine (Item #: 106688, Ref: HS3557) $51.00
Rear Crank Seal Diesel - For the following engines: D327-4, TD327-3, DT268 Turbo Diesel, D155 Diesel, D179 CID, D206 CID, D226-B6, D226-3, D226-4, D226-6, D227-4, D227-6, D239 CID, D246 Diesel, D268 Diesel, D310 CID, D325-2, D325-3, D327-2, D327-3, D358 CID, TD226-B6, TD226-4, and TD228-6. Inside diameter 110mm, Outside diameter 130mm, Width 12.7mm. Does not include wear sleeve. Order RP301113 if wear sleeve is need. Replaces 7701021418, 6005605198, 3138701R91, X550174902000, 89965016008 (Item #: 106657, Ref: 3138701R91) $20.10
Rear Crank Wear Sleeve - This Rear Crankshaft Seal is used for 110mm rear crankshafts on: D155 Diesel Engine, D179 Diesel Engine, D206 Diesel Engine, D239 Diesel Engine, D246 Diesel Engine, DT268 Diesel Engine, D310 Diesel Engine, D358 Diesel Engine. Used with 3138701R91 Seal (not included). (Item #: 106658, Ref: RP301113) $153.00

Engine Parts
Balancer - This Balancer is used in D206, D239, D246 engines. It replaces original part numbers 3132874R91, 3132874R92, 3132874R93, 3228366R91, 3132895R92, 3132895R91, 3132874R94. (Item #: 104256, Ref: 3132874R93) $427.00
Connecting Rod, Reconditioned - The Reconditioned Connecting Rod is used in 454, 464, 574, 674, 484, 684, 784, 884, 485, 585, 685, 785, 885, 495, 595, 695, 895, 2400, 2500, 3400, 3500, 3600, 250A, 260A tractors with D-179, D-239, D-246 Engines. Replaces 1967032C1 and 3055030R24. There is a core charge of $25, when you return your old part, we'll refund the core. (Item #: 210200, Ref: 3055030R24) $109.01
Crankshaft - This Crankshaft is used in IH equipment with D206 Diesel Engines. Has Center Balancer Gear. Replaces 3132968R93 (Item #: 168968, Ref: 3132968R93) $770.00
Crankshaft Balancer Gear - This Balancer Gear is used on D206, D239 and D246 Engines. It has 80 teeth. Replaces 3136237R1. (Item #: 158267, Ref: 3136237R1) $122.00
Crankshaft Gear - This Crankshaft Gear has 33 teeth. It is used on D155, D179, D206, D239, D246 and D268 Engines. Replaces original part number 3055028R1. (Item #: 150037, Ref: 3055028R1) $152.00
Flywheel - Flywheel assembly with ring gear. 12 inch diameter. Tractors: 574, 584, 585, 595, 684, 685, 695, 784, Hydro 84, 3230, 4210. Weight: 88.5 pounds. Additional $20 shipping due to weight. (Item #: 103897, Ref: 1808412C92) $590.00
Flywheel - With Ring Gear. For 574, 584, 595, 674, 684, 784, with D239 engine and 11 inch clutch. 126 teeth on ring gear. Replaces 3136044R42. (Item #: 103903, Ref: R2921) $480.00
No Picture Flywheel - With Ring Gear. For 584, 585, 595, 595XL, 684, 685, 685XL, 695, 695XL, 784 with D239 engine and 12 inch clutch. (Item #: 103897, Ref: R2922) $590.00
Ring Gear - For 385, 395, 454, 464, 484, 485, 495, 574, 584, 595, 684, 685, 695, 784. Flywheel Ring Gear. 126 tooth, 15.93 inch outside diameter, 14.625 inch inside diameter, .562 inches wide. (Item #: 103898, Ref: 60883H) $49.50

Exhaust System
Exhaust Elbow - This Exhaust Elbow is for tractor models 574, 584, 585, (595, 895 up to SN# JJE0014501), 674, 684, 685, 695, 784, 785, 884, 885. (Item #: 160787, Ref: 3136668R1) $125.00
Exhaust Elbow Gasket - For tractor models 474, 574, 584, 585, 595, 674, 684, 685, 695, 784, 785, 884, 885, 895, 3230, 4210, 4220, 4230. (Item #: 160788, Ref: 3136248R1) $3.40
Exhaust Manifold Gasket - Manifold to head, sold individually 4 required for application. For tractor models 474, 574, 584, 585, 595, 674, 684, 685, 695, 784, 785, 884, 885, 895, 3230, 4210, 4220, 4230. (Item #: 101558, Ref: 3132434R1) $3.20
Exhaust Pipe - For tractor models 584, (585 from 1986 and up), 595, 684, 784, 884, 885. (Item #: 160786, Ref: 80547C1) $33.30
Manifold - For tractor models 474, 574, 584, 585, 595, 674, 684, 685, 695, 784, 785, 884, 885, 895, 3230, 4210, 4220, 4230. (Item #: 124679, Ref: 3136066R12) $182.00
Muffler, Vertical - Oval body. Inlet 2-3/8" I.D, outlet 2" O.D, 46" overall length. For tractor models 385, 395, 484, 485, 495, 584 Indust/Const, 595, 684, 685, 784, 884, 885, 895, 985, Hydro 84. Replaces 83027C1, A173180, A173180GV, CA-24. (Item #: 100285, Ref: 83027C1) $95.00

Fuel System / Air Intake
Fuel Injector Nozzle Sleeve - This Fuel Injector Nozzle Sleeve is used on D155, D179, D206, D239, D246, D268, DT268, D310, and D358 Engines. Brass Construction, 3.190 inch overall length 0.386 inch injector tip inside diameter. Replaces 73055344, 3055344R1 (Item #: 165847, Ref: 3055344R1) $24.60
Fuel Shutoff Valve - The threads on this fuel shutoff valve are 1/2 - 20 and 3/8 - 18 NPTF. Used on C50, C60, C70, C80, C90, C100, 385, 395, 485, 495, 585, 595, 685, 695, 785, 885, 895, 995, 3220, 3230, 4210, 4230, 4240, Hydro 84, 248, 258, 268, 278, 385, 454, 464, 474, 484, 485, 574, 584, 585, 674, 684, 685, 784, 785, 884, 885, 2400, 2400A, 2500, 2500A (Item #: 135040, Ref: 528926R1) $24.00
Injector Nozzle - For tractor models 385, 395, (484 serial number 379592 and up), 485, 495, 584, 585, 595, 3220, 3230, 380B. Replaces DLLA150S836. (Item #: 179947, Ref: 3218248R2) $47.50
Manifold Heater - Thermostart Intake Manifold Heater Diesel Engines. Has Applications in many Diesel Models. Replaces Part Numbers: 218349A1, 162000090701, A77616, 3112805R91, K928523, 3118299R1 (Item #: 118792, Ref: 3583543M2) $10.90

Gauges
Tractormeter Cable - Cable Housing is 70 inches long. For tractor models 3210, 3220, 3230, 385, 4210, 4220, 4230, 4240, 484, 485, 584, 585, 585A, 595, 684, 685, 685A, 685XL, 695, 784, 785, 785XL, 795, 85XL, 884, 885, 885XL, 895. Replaces 537494R91, 1536644C1, 1500492C1, 1500716C1, 402024R91. (Item #: 121529, Ref: 537494R91) $28.20

Hitch / Drawbar
Leveling Box Assembly - Cat II, 13-5/8 inch screw. For tractor models 3220, 3230, 395, 4210, 4230, 4240, 495, 595, 695, 895, 995. (Item #: 113621, Ref: 1713-1003) $173.00
Leveling Box Assembly - Cat II, 15.25 inch screw. For tractor models 3220, 3230, 395, 4210, 4230, 4240, 495, 595, 695, 895, 995. (Item #: 124555, Ref: 1713-1004) $115.00
Leveling Box Assembly, RH, Cat I - For tractor models 454, 464, 484, 485, 495, 574, 584, 585, 595, 674, 684, 784, 884. Measures 23 3/4 inch minimum, 28 inch maximum, 1 7/8 inch gap in yoke for thick lift arm. (Item #: 180468, Ref: 223320) $178.75
Leveling Box Fork - This Leveling Box Fork is 14.50 inches long, has a 1-5/8 inch fork width and 0.875 inside diameter. This is a CAT II part. It is used on 3220, 3230, 395, 4210, 4230, 4240, 495, 574, 584 Indust/Const, 595, 674, 684, 685, 695, 784, 884, 885, 895, 995. It is used with 527937R1 Nut, not included. Replaces 402635R4. (Item #: 110393, Ref: 402635R4) $77.00
Leveling Box Screw - This level box screw with bevel gear is 0.875 inches dia, 18.125 inches long. Tractors: 3220, 3230, 395, 4210, 4230, 4240, 495, 595, 695, 895, 995. Replaces 223322, 3072422R2, 3116725R91, 3121964R4. (Item #: 124707, Ref: 3116725R91) $62.62
Leveling Fork Nut - This Leveling Fork Nut is used with 3121964R1 and 402635R4 fork. Replaces original part number 527937R1. (Item #: 110735, Ref: 527937R1) $7.00
Leveling Link Assembly, Cat II - This Leveling Link Assembly Cat II is for tractor models 574, 584, 585, 595, 674, 685, 695, 785, 884, Hydro 84. All with telescopic arm. Consists of: (1) A-527948 lift rod, (1) A-704207R3 swivel, (1) A-3069069R1 pin, (1) A-402635R4 housing, (1) A-527937R1 nut. (Item #: 124553, Ref: 223319) $89.00
Leveling Rod Fork - Housing, leveling screw. Cat I. (14.500 inches long) 1 inch wide fork. Tractors: Hydro 84, 385, 395, 454, 464, 484, 485, 495, 574, 584, 585, 595 with fixed lower link, 674, 684, 685 with fixed lower link, 695, 784 with fixed lower link, 895, 995 ; 3220, 3230 with out telescopic lower link; 4210, 4230, 4240 with out telescopic lower link. (Item #: 108812, Ref: 3121964R91) $66.00
Leveling Yoke Left Hand - This Left Hand Leveling Yoke is 19.250 inches long and 0.875 inch, 9 UNC thread. It replaces original part numbers 527935R1, 527948R91 (Item #: 124678, Ref: 527948R91) $33.60
Lift Yoke Assembly, LH, Cat I - For tractor models 574, 585, 595, 674, 684, 685, 695, 784, 884, Hydro 84 all with fixed arms. (Item #: 124552, Ref: 223318) $88.00

Hydraulic System
Filter, Hydraulic Oil - 5-1/16 inch outside diameter, 2-11/16 inch inside diameter, 3 inches tall. For tractor models (385 serial number 5001 to 5287 and 18001 and up), 485, 585, 685, 885, 395, 495, 595, 695, 895, 3220, 3230, 4210, 4230, 4240, C50, C60, 380B. (Item #: 164964, Ref: 93413C1) $29.10
Hydraulic Pump - For Case/IH: 395, 485, 495, 585, 595, 685, 695, 885, 895, 995. Pump assembly, hydraulic power supply gear pump. Specifications: 18.1 GPM / 68.52 LPM at 1, 000 RPM. Replaces 308873A1, 128180C91, 406763R92, 66513C92, 110509C91, 93835C91, 406827R91, 406763R92, 327988A1, 327987A1. (Item #: 112518, Ref: 93835C92) $240.00

Lights
Headlight Assembly - Pair - Features Glass Lenses with Bulbs, Mounting Hardware and Trim - Left and Right Pair. Replaces 1964881C2, 1964882C2 (Item #: 160300, Ref: R7945) $387.47

Sheet Metal / Body Parts
Battery Door, Metal - This Battery Door is a metal replacement for original fiberglass. It is 18 1/8 Inches Long. Fits the following through 1985: 385, 484, 485, 495, 584, 585, 595, 684, 685, 695, 784, 785, 884, 885. Also fits all years of 395. Replaces: 1536764C1, 3121393R91 (Item #: 104334, Ref: 3121393R91) $122.08
Battery Door, Original - This is an original fiberglass Battery Door. It is 15-5/8 inches wide and 18-5/16 inches long. It does not include hardware. This part is gel coated red for protection. It has a wax releasing agent. It must be prepped before painting. Fits the following through 1985: 385, 484, 485, 495, 584, 585, 595, 684, 685, 695, 784, 785, 884, 885. Also fits all years of 395. Replaces: 1536764C1, 3121393R91 (Item #: 104334, Ref: 1536764C1) $122.08
Fender, LH, Hi-Crown - For tractor models 584, 585, 595, 684, 685, 695, 784, 884, 885, 895. Additional $20 for shipping will be charged due to size/weight of this item. Sheet metal parts may or may not come painted as pictured (unless the description states the color). They often come with only a primer coat of paint. (Item #: 113787, Ref: 538641R4) $184.00
Fender, RH, Hi-Crown - For tractor models 584, 585, 595, 684, 685, 695, 784, 884, 885, 895. ** Add $20 for shipping due to size/weight ** Sheet metal parts may or may not come painted as pictured (unless the description states the color). They often come with only a primer coat of paint. (Item #: 113788, Ref: 136165A1) $203.00

Steering
Axle Support Bushing - Used on Carraro 4WD front ends, this bushing measures 4.921 inches outside diameter, 4.527 inches inside diameter and is 1.653 inches long. Replaces OEM numbers K965756, K965265, 1-33-241-048, 9967992, K965265, CAR101575/1, CAR123477, CAR1015751, 9967992, 83930079, 83930554, R113767, 3541395M1 (Item #: 156131, Ref: CAR1015751) $91.21
Ball Joint and Rod - This part is 7.540 inches long and M20 X 1.5 right hand thread. Used on: 238, 238 UK Series, 248, 248 UK Series, 258, 258 UK Series, 268, 268 UK Series, 288, 288 UK Series, 395, 395 UK Series, 485, 485 UK Series, 495, 495 UK Series, 585, 585 UK Series, 595, 595 UK Series, 685, 685 UK Series, 695, 695 UK Series, 743, 743 European, 745, 745 European, 745S, 785, 785 UK Series, 795, 795 UK Series, 844, 844 European, 844S, 844XL, 844XL European, 845, 845 European, 856XL, 856XL European, 885, 885 UK Series, 895, 895 UK Series, 995XL, 995XL UK Series. Replaces 1968463C1, 1868468C1, 1968468C1. (Item #: 104398, Ref: ZP0501310060) $53.00
Bushing, Front Axle Steering Arm - For tractor models 385, 395, 454, 474, 475, 484, 485, 485XL, 495, 495XL, 574, 584, 585, 585XL, 595, 595XL, 674, 684, 685, 685XL, 695, 695XL, 784, 785, 785XL, 795, 795XL, 884, 885, 885XL, 895, 895XL, 995, 995XL, 2400, 2500, 3220, 3230, 4210, 4220, 4230, 4240, C50, C60, C70, C80, C90, CX50, CX60, CX70, CX80, CX90, CX100. Replaces 153687C1. (Item #: 104494, Ref: 405574R1) $6.90
Bushing, Front Axle, Steering Arm - Associated with 379555R11 steering arm. For tractor models 385, 395, 454, 474, 475, 484, 485, 485XL, 495, 495XL, 574, 584, 585, 585XL, 595, 595XL, 674, 684, 685, 685XL, 695, 695XL, 784, 785, 785XL, 795, 795XL, 884, 885, 885XL, 895, 895XL, 995, 995XL, 2400, 2500, 3220, 3230, 4210, 4220, 4230, 4240, C50, C60, C70, C80, C90, CX50, CX60, CX70, CX80, CX90, CX100. (Item #: 104493, Ref: 379748R1) $9.00
Differential Pinion Bearing - Used on Mechanical Four Wheel Drive axles APL325, APL335, APL345, APL350, and APL355, this bearing is used with the pinion gears closest to the hub. Replaces E2NN1N055AA, 135700421044, 81326C1, 83927802, 83934020, 153317487, 1429562, M382179, 1-31-742-032, 04350447, F198300020650, E1NN1N055AB, JD10250, AL39377. (Item #: 112468, Ref: 81326C1) $43.50
Differential Pinion Bearing - Used on mechanical four wheel drive front ends, this open roller bearing measures 1.42 inches inside diameter, 2.28 inches outside diameter and 0.78 inches wide. Replaces OEM numbers International Harvester - 81326C1, Ford/New Holland - 83934020, E2NN1N055AA, John Deere - AL39377, JD10250 (Item #: 112468, Ref: VPJ2550) $43.50
Differential to Axle Housing Seal - On ZF Axles, this o-ring goes between the deferential case and the axle housing. Used on APL 325 and APL 330 axles. Replaces E1NN3N267AA, 81279C1, 83927734, L40306 (Item #: 156189, Ref: E1NN3N267AA) $2.20
Final Drive Shaft - Used in Mechanical Four Wheel Drive front ends, this part replaces: E1NN3A328AB, L40029, 81453C1, 83927740, 83934903. It has 18 teeth on both ends. (Item #: 124721, Ref: L40029) $95.00
Front Axle Bolt - Used to secure front axle knees, this bolt measures 4-3/4 inches overall, 4 inches to the shoulder and has 3/4-16 UNF RH Thread. If nuts are needed, order 116643. Replaces part number 405584R1 (Item #: 124558) $10.00
Front Axle - Differential Housing Bushing - The measurements on this bushing are: 4.525 inches outside diameter, 4.127 inches inside diameter, 1.730 inches long. This bushing is used on Carraro 4WD front end. Replaces OEM numbers 101565, K965266, CAR1015651, 83945601, CAR101565/1, CAR123478, 83930062, 9967993, R113766, 3541396M1, 040953R1 (Item #: 156132, Ref: CAR1015651) $79.00
Front Axle Knee, Left Side - Used on the following with Swept Back Axles: 2500A, 385, 395, 484, 485, 495, 584, 585, 595, 685, 695, 885, 895, 995, 574. This Front Axle Knee measures 9.500 inches from the top of the thrust bearing to the top of the tube. Comes with 358958R2 bushing. If thrust bearing is needed, order 185106C1. Replaces 66701C91, 405712R12 (Item #: 110733, Ref: 405712R12) $539.00
Front Axle Knee, Right Side - Used on the following with Swept Back Axles: 2500A, 385, 395, 484, 485, 495, 584, 585, 595, 685, 695, 885, 895, 995, 574. This Front Axle Knee measures 9.500 inches from the top of the thrust bearing to the top of the tube. Comes with 358958R2 bushing. If thrust bearing is needed, order 185106C1. Replaces 405713R12, 66702C91 (Item #: 108890, Ref: 405713R12) $325.00
Front Axle Nut - Used with part number 124558 to secure axle knees, this nut is 3/4 inch -16 UNF thread. Replaces 405576R1 (Item #: 116643) $2.40
Front Axle Pivot Shaft - This Front Axle Pivot Shaft is 13.250 inches Long. It is used on 2400, 2500A, 380B, H84, 385, 395, 454, 464, 484, 485, 584, 585, 595, 674, 684, 685, 695, 784, 884, 885, 895, CX100, CX50, CX60, CX70, CX80, CX90. Replaces 405564R91, 405577R1, 405577R2, 527790R91, 538688R91, 539128R1 (Item #: 124722, Ref: 539128R1) $220.00
Half Shaft Bushing - Used on ZF MFWD Axles this busing measures 1.462 inches inside diameter, 1.616 outside diameter, and 1.259 long. Replaces OEM numbers 81429C2, 81429C1, 83956842, L40017, L60747, ZP0730260617. Used on International models: 395, 485, 495, 585, 595, 685, 695, 743XL, 745XL, 785, 795, 844XL, 845, 856XL, 885, 895, 995 (Item #: 124593, Ref: L60747) $12.80
Half Shaft Bushing - Measuring 1.457 inches inside diameter, 1.638 inches outside diameter and 1.024 inches wide, this is the inner bushing on ZF APL325 Mechanical Four Wheel Dive axles. Replaces OEM part numbers 81410C2, 83956843, L60748, L40018, ZP0730260616. This front axle can be found on the following International models: 385, 395, 485, 495, 585, 595, 685, 695, 743XL, 745XL, 785, 795, 844XL, 845, 856XL, 885, 895, 995 (Item #: 124592, Ref: L60748) $14.20
Hub Seal, Inner - Found in many MFWD (mechanical four wheel drive) front ends, this seal measures 4.80 inches inside diameter, 5.90 inches outside diameter, 0.53 inch width. It replaces OEM numbers 81869544, 83946025, 83932098, 83927796, E1NN1214AC, 1456320, ZP0734309421, ZP0750110140, ZP0734317062, ZO0750110147, ZP0750110147, AL68210, 84295352, 81311C1, 1964235C1, 1964235C2, 81309C1, 81310C1 (Item #: 124718, Ref: ZP0750110147) $58.00
Joint Assembly, MFWD - Used on ZF APL325 Mechanical Four Wheel Drive front ends, this part replaces OEM part numbers 1968450C1, 81430C1, 83961165, AL63606, AL38018, AL64250, ZP7029910201. This axle was used on International models: 385, 395, 485, 495, 585, 595, 685, 695, 885, 895 (Item #: 156193, Ref: AL63606) $596.00
O-Ring / Seal - Made of Nitrile Rubber, this o-ring measures 7.874 inches inside diameter with a 0.118 inch thickness. It is used in many mechanical four wheel drive systems. Replaces OEM numbers 81313C1, 81326C1, 1-31-742-032, 71452157, E1NN1N050AA, 83927797, L40317, AL40317 (Item #: 156198, Ref: E1NN1N050AA) $6.90
Pivot Pin Seal, MFWD - For ZF APL325 or APL350 Mechanical Four Wheel Drive front axles, this o-ring has a 1.346 inch inside diameter and is 0.118 inches thick. Replaces OEM numbers 81419C1, 83927817, E1NN3125AA, L53819. These axles can be found on International models: 395, 485, 495, 585, 595, 685, 695, 743XL, 745XL, 785, 795, 844XL, 845, 856XL, 885, 895, 995 (Item #: 124690, Ref: L53819) $2.60
Planetary Carrier Housing - Used on ZF APL-325 Axles on International models 385, 395, 485, 495, 595 (Item #: 127236, Ref: VPR6067) $1389.01
Planetary Gear - Used in APL 335 and APL 330 Axles, on tractors with mechanical four wheel drive, the is the gear closest to the hub. Sold individually. Replaces OEM numbers ZP4472352014, ZP0769126276, 83946053, 81325C1. Used on International models: 238, 248, 258, 268, 288, 385, 395, 485, 485XL, 495, 495XL, 585, 585XL, 595, 595XL, 685, 685XL, 695, 695XL, 743, 743S, 743XL, 745, 745S, 745XL, 785, 785XL, 795, 795XL, 844, 844S, 844XL, 845, 845XL, 856, 856XL, 885, 885XL, 895, 895XL, 985, 985XL, 995, 995XL (Item #: 124634, Ref: ZP4472352014) $118.84
Planetary Gear - Used on International models 395, 485, 495, 595 with Mechanical 4 Wheel Drive. Three are used per housing. Sold individually. This part replaces 81455C1, E1NN4044AB, L40028 (Item #: 124631, Ref: VPJ7852) $107.00
Planetary Ring Gear - For Mechanical Four Wheel Drive, this planetary ring gear has 114 spines and an outside diameter of 8.16 inches. This part replaces OEM numbers 81452C1, 83927789, L40043 (Item #: 124630, Ref: L40043) $366.80
Power Steering Cylinder Plate - Used on 3210, 3220, 3230, 385, 395, 4210, 4220, 4230, 4240, 454, 474, 475, 484, 485, 495, 584 Indust/Const, 595, 674, 684, 685, 695, 784, 785, 795, 884, 885, 895, 995, C100, C50, C60, C70, C80, C90, CX100, CX50, CX60, CX70, CX80, CX90, MX100C, MX80C, MX90C (Item #: 124616, Ref: 405580R21) $41.00
Power Steering Cylinder Rod - Used on UK built International 2 wheel drive tractors, this part replaces 549668R1, 549668R2, 188851A1, 549668R3, 188854A1. Used on 238, 248, 258, 268, 288, 3210, 3220, 3230, 385, 395, 4210, 4220, 4230, 4240, 454, 474, 475, 484, 485, 485XL, 495, 495XL, 574, 584, 585, 585XL, 595, 595XL, 674, 684, 685, 685XL, 695, 695XL, 784, 785, 785XL, 795, 795XL, 884, 885, 885XL, 895, 895XL, 995, 995XL, CX100, CX50, CX60, CX70, CX80, CX90, Hydro 84, Hydro 86, MX100C, MX80C, MX90C (Item #: 182916, Ref: 549668R1) $298.00
Roller Bearing with Cup MFWD - Used on ZF APL315, APL325, and APL330 Mechanical Four Wheel Drive Axles, the pivot bearing replaces OEM part numbers 1342525C2, 1342525C1, 81416C1, 81417C1, 83958377, AL63617, ZP0750117306, LM72848 and LM72810. These axles can be found on International models: 395, 485, 495, 585, 595, 685, 695, 743XL, 745XL, 785, 795, 844XL, 845, 856XL, 885, 895, 995 (Item #: 124691, Ref: AL63617) $47.40
Seal Kit, Power Steering Cylinder - For 2 wheel drive models 454, 464, 574, 674, 484, 584, 684, 784, 884, 385, 485, 585, 685, 885, 595, 695, 995, 2400, C50, C60, C80, C90, C100, 4210, 4230, 4240. VERIFY PART NUMBER TO ENSURE CORRECT REPLACEMENT. (Item #: 115098, Ref: 55355C91) $39.90
Spindle Bushing - Fits 1.667 inch diameter spindles replaces 376099R1. For use with A-71785HD and OEM spindle. (Item #: 102175, Ref: 358958R2) $9.70
Spindle Felt Seal - This Felt Washer is used with 405840R12 and 534288R91 Spindles. Fits tractor models 238, 248, 258, 385, 395, 454, 475, 474, 484, 485, 485XL, 495, 495XL, 574, 584, 585, 585XL, 595, 595XL, 674, 685, 695, 885, 895, 3220, 3230, 4210, 4230 and 4240. (Item #: 102176, Ref: 15943DA) $2.20
Spindle, L/R - This spindle works both Left hand and right hand. Shaft length 12.125 inch, shaft diameter 1.687 inch, inner bearing 1.375 inch, outer bearing .842 inch. For models 238, 248, 258, 385, 395, 454, 474, 475, 484, 485, 485XL, 495, 495XL, 574, 584, 585, 585XL, 595, 595XL, 674, 685, 695, 885, 895, 3220, 3230, 4210, 4230, 4240, C50, C60. The wheel bearing kit used for this spindle is part number WBKIH6. (Item #: 100844, Ref: 405840R12) $223.00
Spindle, L/R - This spindle replaces both Right hand and left hand. 15.265 inches in length, A=1.687 inch, B=1.375 inch, C=.843 inch, .75 inch UNF thread. For tractor models 238, 248, 258, 454, 474, 475, 574, 674, 484, 584, 385, 485, 485XL, 585, 585XL, 395, 495, 595, 595XL. The wheel bearing kit used for this spindle is part number WBKIH6. (Item #: 100845, Ref: 527292R92) $251.00
Spindle Nut - Fits on Front Spindles. Castle Nut 3/4 inch x 16 UNF. P2060, VLG3307, 351129S, 353928X1, 354573S36, 387930S36, 646060M1, 83416613, 83900513, 83910701, 880284M1, 9073, 98A750N, 129-290, 88886, 427639, 88886 (Item #: 156038, Ref: 387930S36) $1.10
Spindle, RH/LH - Has a shaft length of 9.50 inch, width 1.667 inch, inner bearing 1.375 inch, outer bearing .843 inch. For tractor models 2400A, 2500A, 380B, 385, 395, 454, 484, 485, 495, 574, 584, 585, 595, 595XL. The wheel bearing kit used for this spindle is part number WBKIH6. (Item #: 104326, Ref: 534288R91) $292.00
Spindle, RH/LH - This spindle measures A= 8.312 inch, B= 1.667 inch, C= 1.375 inch, D= .843 inch. For tractor models 495, 585, 595, 595XL, 685, 685XL, 695, 695XL. The wheel bearing kit used for this spindle is part number WBKIH6. (Item #: 104327, Ref: 1332982C1) $266.00
Spindle, RH/LH - This spindle measures A= 12.125 inch, B= 1.667 inch, C= 1.780 inch, D= 1.375 inch. For tractor models 585, 595, 595XL, 695, 695XL, 895, 895XL. The wheel bearing kit used for this spindle is part number WBKIH9. (Item #: 100847, Ref: 67535C91) $209.00
Spindle, RH/LH - This spindle measures A= 8.312 inch, B= 1.667 inch, C= 1.780 inch, D= 1.375 inch. For tractor models 268, 278, 3230, 4210, 4230, 4240, 584, 585, 595, 595XL, 684, 685, 685XL, 695, 695XL, 784, 785, 884, 885, 885XL, 895, 895XL, 995, C100, C70, C80, C90, CX100, CX70, CX80, CX90, Hydro 84. The wheel bearing kit used for this spindle is part number WBKIH9. (Item #: 100846, Ref: 3121270R91) $169.71
Spindle, RH/LH - This spindle measures A= 11.250 inch, B= 1.667 inch, C= 1.780 inch, D= 1.375 inch. For tractor models 268, 278, 3230, 4210, 4240, 585, 595, 595XL, 684, 685, 685XL, 695, 695XL, 784, 785, 884, 885, 885XL, 895, 895XL, C100, C70, C80, C90, CX100, CX70, CX80, CX90, Hydro 84. The wheel bearing kit used for this spindle is part number WBKIH9. (Item #: 104329, Ref: 3121261R91) $201.00
Steering Arm, Right Hand - This Right Hand Steering Arm is used on 268, 278, 3230, 4210, 4230, 4240, 585, 595, 684, 685, 695, 784, 785, 884, 885, 895, 995, CX100, CX70, CX80, CX90, Hydro 84. It replaces 3121264R1 (Item #: 124741, Ref: 3121264R1) $261.00
Steering Bar Assembly - For tractor models 238, 248, 258, 268, 288, 3210, 3220, 3230, 385, 395, 4210, 4220, 4230, 4240, 454, 474, 475, 484, 485, 485XL, 495, 495XL, 574, 584, 585, 585XL, 595, 595XL, 674, 684, 685, 685XL, 695, 695XL, 784, 785, 785XL, 795, 795XL, 84 Hydro, 884, 885, 885XL, 895, 895XL, 995XL. (Item #: 124616, Ref: 405580R11) $41.00
Steering Joint - This Steering Joint is 7.040 over all length. The Inner Thread is M20 X 1.5 RH Thread. The Outer Thread is M18 X 1.5 LH Thread. Replaces 1966127C1, 83957148, CAR49006, 1-33-743-602, 112508A1 (Item #: 104634, Ref: CAR49006) $57.00
Taper Roller Bearing - Measuring; Width - 0.548 inches, Inside Diameter - 3.740 inches, Outside Diameter - 5.315 inches, this bearing is used in ZF Axles on tractors with mechanical four wheel drive. This bearing also has other applications. Replaces OEM numbers: ZP0750117062, 5136951, 83946047, 81312C1, 83927807, 47539809, 1-31-741-019, 05136951, 85136951, 85806002, 1966169C1, CAR118378, 83983456, AL38099, RE45944, 819310, 819349/819310, 819349 (Item #: 156177, Ref: ZP0750117062) $82.70
Thrust Bearing - Fits Models: 1026, 1066, 1086, 1206, 1256, 1456, 1466, 1468, 1486, 1566, 1586, 1822, 1844, 2022, 2044, 21026, 2400A, 2500A, 2656, 2706, 2756, 2826, 2856, 300, 3088, 3288, 350, 3688, 380B, 385, 395, 400, 450, 454, 484, 485, 495, 504, 5088, 5288, 544, 5488, 560, 574, 584, 585, 595, 595XL, 656, 66, 666, 674 with STRAIGHT AXLE. 1.755 inches inside diameter, 2.685 inches outside diameter, 0.694 inches wide. Replaces 185106C1, 185106C91, 357349R91, 361034R91, 369131R91, 387231R91, 405831R91, 527295R91, 844398R91 (Item #: 102174, Ref: 185106C1) $12.80
Tie Rod - Tie rod end, outer, recess for set screw (7) at bottom, 15 inch to center of post, .812 inch rod diameter. Used on tie rod assemblies with set screw recess outer end and threaded inner end. For straight adjustable axles 52 to 80. For tractor models Hydro 84, 385, 395, 484, 485, 495, 584 except utility For 385, 395, 484, 485, 495, 584, 595, 684, 685, 695, 784, 884, 885, 895, 995, HYDRO 84. Replaces 3116406R3, 1332805C1, 3125171R1, 1332805C2. (Item #: 100865, Ref: 3116406R3) $27.50
Tie Rod - Tie rod end, inner, right hand thread, 3-7/8 inch to center of post. 0.875 Inch x 16 RH Thread. Used on tierod assemblies with set screw recess outer end and threaded inner end. For straight adjustable axles 52 to 80 on tractors: Hydro 84, 385, 395, 484, 485, 495, 584, 684, 784, 884. 52 to 82 on tractor For 385, 395, 484, 485, 495, 584, 595, 684, 685, 695, 784, 884, 885, 895, 995, HYDRO 84. (Item #: 100864, Ref: 3116407R3) $17.60
Tie Rod - Tie rod end, outer, recess for set screw (6), 14-1/8 inch to center of post. Used on tie rod assemblies with set screw recess outer end and threaded inner end. For straight adjustable axles 52 to 77 on tractors: Hydro 84, 595, 684, 685, 695, 784. 884, 885, 895, 995.52 For 584, 595, 684, 685, 695, 784, 884, 885, 895, 995, HYDRO 84 (Item #: 100872, Ref: 3125171R2) $36.90
Tie Rod Assembly - This Tie Rod Assembly is used on Adjustable Straight Axles (52 Inches to 82 Inches Tread Width). It Replaces 3125171R2, 3125171R3, 1332805C2, 3116406R3, 3116406R4, 3116406R5, 3116321R93, 1538016C1. (Item #: 156878, Ref: 1538016C1) $127.00
Tie Rod Assembly, Complete - Due To Multiple OEM Styles, Individual Pieces May Not Fit Models Listed, But Can Use Assembly As A Replacement. Assembly Consist Of: (1) 65079C91, (1) 527658R91, (1) 67529C1, (1) 390686R1, (1) 43747D. 65079C91: Stud Taper= .606 To .700 inches, 527658R91: Stud Taper= .606 To .700 inches. Used on 574, 2400A Straight Front Axle serial number 100006 and up, 2500A Straight Front Axle serial number 100004 and up, 385 Straight Front Axle, 454 Straight Front Axle serial number 100006 and up, 484, 485, 495 Straight Front Axle, 584 Adjustable Straight Front Axle, 585, 595 Adjustable Straight Front Axle, 674 Straight Front Axle, 684, 695 Adjustable Straight Front Axle, 784, 884, 885 below serial number 3083. (Item #: 124766, Ref: 223326) $115.00
Tie Rod Assembly, Complete - Due To Multiple OEM Styles, Individual Pieces May Not Fit Models Listed, But Can Use Assembly As A Replacement. Assembly Consists Of: (1) 65082C91, (1) 527658R91, (1) 527659R2, (1) 390686R1 and (1) 43747D. 65082C91: Stud Taper = .606 To .700 inches, 527658R91: Stud Taper = .606 To .700 inches. Used on 574, 2400A, 385, 485, 495, 584, 595, 695. (Item #: 124765, Ref: 223324) $147.00
Tie Rod Clamp - Used on Farmall / IH models, this tie rod clamp fits 574, AV, AV1, A1, CUB, SUPER A, 100, 130, 140, 200, 230, 240, 2400, 248, 2500, 2504, 258, 3230, 340, 385, 404, 4210, 4230, 4240, 454, 474, 484, 485, 504, 584, 585, 595, 674, 684, 685, 695, 784, 884, 885, 995 (Item #: 104368, Ref: 43747D) $17.30
Tie Rod End - Dimension A= 4.060 inch, B= 0.812 inch (16 UN right hand thread). Fits the following tractors with ADJUSTABLE CAST I-BEAM FRONT AXLE: Hydro 84, 454, 484, 485, 495, 544, 574, 585, 595, 595XL, 656, 684, 685, 695.YTO-379327R91_. (Item #: 104406, Ref: 379327R91_) $27.90
Tie Rod End - This Tie Rod End is 9.750 inches long and has M22 x 1.5 inch right hand thread. It replaces original part number 1968464C1. (Item #: 124764, Ref: 1968464C1) $45.30
Tie Rod End - Used on the following with non-adjusting Cast I Beam front axles: 574, 2400A, 2500A, 2544, 2656, 380B, HYDRO 84, 454, 484, 485, 495, 544, 584, 585, 595, 595XL, 656, 684, 685, 685XL, 784, 884, 885, 885XL, 895, 895XL. A= 4.00 inch, B= 13/16 inch, 16 left hand thread. Replaces 379326R91 (Item #: 104593, Ref: C5NN3A300C) $27.30
Tie Rod End - The measurements on this Tie Rod End are as follows: 3-3/4 inches from the center of the ball joint to the end of the shaft, 7/8 16 UN RH Thread on shaft. Replaces 1537872C1 (Item #: 123097) $59.00
Tie Rod (Steering Cylinder) - This Tie Rod End is 6.750 from center of ball joint to end of rod. 18mm x 1.5 right hand thread. Replaces CAR48998, 81875595, 81878543, 1537612C1, 137048A1 (Item #: 104374, Ref: CAR48998) $89.00
Tie Rod Tube - This Tie Rod Tube is 16.187 inches long and with 7/8 inch 16 thread. It replaces 3116408R1. (Item #: 104409, Ref: 3116408R1) $32.50
Universal Joint - Measuring 27mm 1 1/16 inches) x 70mm (2 3/4 inches) this universal joint is used on the axle of APL 335, 325, 345, 350, and 300. Replaces OEM numbers ZP7029457207, 83964587, 84355357, ZP7029457210, 1342711C1, 81873051, 144465A1, 1342715C1, 83956476, ZP0501205345, 9968059, 247543A1, AL64126 (Item #: 124613, Ref: 1342711C1) $102.00
Wheel Half Shaft Seal, MFWD - Used on ZF APL325 Mechanical Four Wheel Drive front ends, this seal measures 1.388 inches inside diameter, 2.055 inches outside diameter and is 0.588 inches wide. Replaces OEM numbers 81411C2, 83956841, 83961163, AL63351, AL68702, ZP07050110133. Used on International models: 395, 485, 495, 585, 595, 685, 695, 743XL, 745XL, 785, 795, 844XL, 845, 856XL, 885, 895, 995 (Item #: 124717, Ref: AL63351) $21.80
Wheel Hub Trunnion Pin - Also known as a King Pin, this Wheel Hub Trunnion Pin is used on ZF APL325 Mechanical Four Wheel Drive front ends. This part replaces L40036, ZP4472351239, 81428C1, 83946561, E1NN3B626AA. Verify your axle before ordering. Some of the models listed used more than one 4 wheel drive front end. Used on International models: 385, 395, 485, 495, 585, 595, 685, 695, 743XL, 745XL, 785, 795, 844XL, 845, 856XL, 885, 895, 995 (Item #: 124687, Ref: E1NN3B626AA) $77.00

Wheels
Front Rim - This is a 5.5 inch x 18 inch Front Wheel Rim. Used with 7.50 x 18 Tires. It has a pilot hole of 4.656 inches. It uses 6 bolts in a 6 inch bolt pattern. Verify size of old rim before ordering. Replace 3121425R91, 804711R91, K301046, K949731, 3121425R91, 83960329, C7NN1007B, 83918556, 81825697, 81820016, D1NN1007C, D8NN1007CA, 82005057, 82033932, E6NN1007CA, D4NN1007N, JD3211, AL82491, 3827583M91, 186319M91, 1861319M91 (Item #: 167680, Ref: FW55186) $138.00
Front Wheel Hub, 6 Bolt - For tractor models 2400A, 2500A, 380B, 385, 395, 454, 484, 485, 495, 574, 584, 585, 595, 595XL, 674, 685, 685XL, 695, 695XL, 885, 895, 995. Note: hub uses WBKIH6 wheel bearing kit. Replaces 406294R21, 406294R11 (Item #: 104503, Ref: 406294R21) $151.00
Front Wheel Hub, Heavy Duty - 6 bolt. For tractor models 268, 278, 3230, 4210, 4230, 4240, 574, 584, 585, 595, 595XL, 684, 685, 685XL, 695, 695XL, 784, 785, 884, 885, 885XL, 895, 895XL, 995, C100, C70, C80, C90, CX100, CX70, CX80, CX90, Hydro 84. (Item #: 124067, Ref: 67527C91) $137.00
Hub Cap - This Hub Cap is used with hubs: 67527C91, 406294R21, 406292R11, 536058R11. It is 2.5 inches in diameter. It replaces 612884R1, 47468696. (Item #: 115100, Ref: 612884R1) $5.10
Wheel Bearing Kit - Complete for one wheel. For tractor models 574, 584, 585, 595, 595XL, 674, 684, 685, 685XL, 695, 695XL, 784, 884, 885, 885XL, 895, 895XL, Hydro 84. Kit contains: LM102949 (Cone), LM102910 (Cup), L68149 (Cone), L68111 (Cup), 22322 (Lip Seal), 67328C1 (Retainer). (Item #: 100858, Ref: WBKIH9) $35.80
Wheel Bearing Kit - For tractor models 2400A, 2500A, 380B, 385, 395, 454, 484, 495, 574, 584, 585, 595, 595XL, 674, 685, 685XL, 695, 695XL, 784. Kit contains: LM48548 (Cone), LM48510 (Cup), M12649 (Cone), M12610 (Cup), 530104R91 (Seal), 406295R1 (Retainer-NOT SHOWN). (Item #: 100857, Ref: WBKIH6) $34.90
Wheel Hub, Front - Used on IH models 238, 248, 258, 268, 288, 3210, 3220, 3230, 385, 395, 4210, 4220, 4230, 4240, 454, 475, 484, 485, 485XL, 495, 495XL, 574, 584, 585, 585XL, 595, 595XL, 674, 684, 685, 685XL, 695, 695XL, 784, 785, 785XL, 795, 884, 885, 885XL, 895, 895XL, 995, C100, C50, C60, C70, C80, C90, CX100, CX50, CX60, CX70, CX80, CX90, Hydro 84, Hydro 86, MX100C, MX80C, MX90C this Front Hub replaces OEM number 67527C92, 67527C91. Uses Wheel Bearing Kit WBKIH6 (Item #: 124067, Ref: 67527C92) $137.00
Universal Parts and Accessories Category: Accessories / Supplies

Accessories / Supplies
Auxiliary Heater, Universal - This universal auxiliary heater is used for tractor cabs, combines, backhoes, dozers, forklifts, etc. using 5/8 inch heater hose connections. Hot water forced air heat. Dimensions: 6-1/2 inches x 9-1/2 inches x 9 inches, steel powder coat housing with aluminum core. 3-speed high volume squirrel cage fan, 12-volt, 20, 000 BTU includes switch, brackets, instructions. (Item #: 182644, Ref: MIS3127) $385.00
Magnetic Block Heater - Universal. Magnetic utility heater. 120 volt AC, 200 Watts. Built-in thermostat maintains optimum temperature - will not exceed 250 degree F (121 degree C). Quick-grip handle protects hands from heat. 4-3/8 inches (11cm) length, 2-1/2 inches (6.3cm) width, 3 inches (7.5cm) height (including handle). (Item #: 178758, Ref: MBH1153) $97.00

Decals and Emblems
Decal, Fear This IH - Black and red, 12-1/2 x 3-3/4. For all Models. (Item #: 183484, Ref: S.67826) $15.80
Decal, IH Block - "IH" logo, 11 inches. (Item #: 183564, Ref: R4682) $17.40
Decal, IH Block - "IH", 3 inch x 3 1/4 inch Block. (Item #: 101094, Ref: R4681) $6.40
Decal, IH Block - "IH" logo, 1 3/4 inch. (Item #: 183266, Ref: R4680) $5.00
Decal, IH Block - "IH", 1 1/4 inch Logo . (Item #: 183058, Ref: R4679) $3.90
Decal, IH Block - "IH" logo, 7 inches printed on vinyl. (Item #: 183292, Ref: R5171) $25.80
Decal, IH Block - "IH" logo, 8 inches printed on vinyl. (Item #: 183123, Ref: R5172) $30.50
Decal, IH Block - "IH" logo, 10 inches. (Item #: 183276, Ref: R5173) $36.60
Decal, IH Block - "IH" logo no background, 1 inch printed on vinyl. (Item #: 183334, Ref: R5174) $2.60
Decal, IH Block - "IH" logo no background, 1-5/8 inches printed on vinyl. (Item #: 183338, Ref: R5175) $3.90
Decal, IH Block - "IH" logo no background, 2 inches x 2-1/2 inch printed on vinyl. (Item #: 183347, Ref: R5176) $5.00
Decal, IH Block - "IH" logo no background, 3 inch x 3-1/2 inch printed on vinyl. (Item #: 183352, Ref: R5177) $14.20
Decal, IH Block - "IH" logo no background, 4-1/2 inch x 4-3/4 inch printed on vinyl. (Item #: 183255, Ref: R5178) $7.50
Decal, IH Block - "IH" logo no background, 5-1/2" x 6" printed on vinyl. (Item #: 183265, Ref: R5179) $16.60
Decal, IH Block - "IH" logo no background, 6-1/2 inch x 7 inch. (Item #: 183547, Ref: R5180) $12.40
Decal, IH Block - "IH" logo no background, 7-1/2 inch x 8 inch. (Item #: 183556, Ref: R5181) $14.80
Decal, IH Block - "IH" logo on silver background, 2 inch x 2-1/4 inch. (Item #: 183560, Ref: R5182) $14.20
Decal, IH Block - "IH" logo no background, 10 inch x 11 inch. (Item #: 183543, Ref: R5183) $25.50
International Decal - 8-1/2 inch long, white with black outline. (Item #: 183068, Ref: R0679) $9.40
International Decal - 23 inches long, black block letters. (Item #: 183477, Ref: R0680) $12.40
International Decal - 23 inches long, white with black outline. (Item #: 183478, Ref: R0681) $16.60
International Decal - 26 inches long, black block letters. (Item #: 183481, Ref: R0682) $14.80
International Decal - 26 inches long, white with black outline. (Item #: 101032, Ref: R0683) $14.00
International Decal - 29 inches long, black block letters. (Item #: 101030, Ref: R0684) $10.50
International Decal - 29 inches long, white with black outline. (Item #: 101033, Ref: R0685) $17.50

Electrical System
NOTE Alternator - Don't see the Alternator you need for your tractor? We have many alternators not listed on this website (for tractors 1953 and newer). Just call us at 800-853-2651.	NOTE
No Picture Alternator, 12 Volt - Universal 63 Amp Delco Alternator. Single wire with built in regulator. Will fit most tractors pre 1980. (Item #: 111377, Ref: 8NE10305SE) $96.00
Alternator Conversion Plug - Used to turn Delco SI Style 2-Wire plug alternators into self-exciting style. (Item #: 178026, Ref: ADR9209) $14.40
Alternator Top Adjusting Bracket, Universal - Universal Top Adjusting Bracket for Alternator or Generator is 7/8 inches wide, 1-1/2 inch offset, 8-1/4 inch from farthest end of slot to center of mounting hole, 3-3/4 inch slot length, 3/8 inch mounting hole. (Item #: 173326, Ref: 8NL10302) $25.20
No Picture Battery Thermal Wrap - 60 Watt, 28 inches long wrap to keep your battery warm. (Item #: BTW28) $35.98
No Picture Battery Thermal Wrap - 160 Watt, 36 inches long wrap to keep your battery warm. (Item #: BTW72) $53.81
No Picture Coil - This universal automotive style coil is 28, 000 volts for a 12 volt system, 2.9 ohms. Measures 6 inches long and 2 1/2 inches diameter. (Item #: 182583, Ref: 28010) $49.20
Distributor Cap, WICO - For All Models with WICO distributor having clip type cap with 3 3/8 inside diameter seat. (Item #: 108299, Ref: X30042) $62.15
Magneto, Wico XH and XHD, Service and Parts Manual - Wico XH And XHD magneto service instructions and parts list. This is a reprint of the original manual that has exploded views of all parts on the tractor with numbered pictures giving great detail on assembly and disassembly. It also gives you a guide with numbers for ordering parts. (Item #: 182504, Ref: MAG6) $19.20
No Picture Spark Plug - Extended tip, 14mm thread, 3/8 inch reach. Replaces Champion J10Y, J11Y, J12Y, J13Y. NOTE: Verify spark plug type before ordering. (Item #: 179437, Ref: AL85) $5.60
Spark Plug - Standard tip, 14mm thread, .472" reach. Replaces Champion L9J, L10, L86, L86C, L88A, L90. NOTE: Verify spark plug type before ordering. (Item #: 182459, Ref: AL425) $4.80
NOTE Starter - Don't see the starter you need for your tractor? We probably have it! Just call us at 800-853-2651 with your make, model, engine cubic inches (CID) and number off your old starter and we will see if we can find it!	NOTE
Starter, Generator, Distributor Tag, 6 Volt, Blank - Comes with 2 rivets. 2.5" long, .800" wide, 2" center to center rivet hole, .150" dia. rivet holes. Customer must stamp numbers. (Item #: 182608, Ref: DELCO6) $16.80
Starter Solenoid - This is a 3 post, 12 volt Starter Solenoid. Can be used as a saddle mount or flat surface mount. May come in a metal or plastic casing. Replaces: 1114200, 1114207, 1114216, 1114225, 1114235, 1114545, 1114548, 1118820, 1996067, D928, DR1467, DR1485. May come in a silver metal casing versus black plastic. (Item #: 150223, Ref: DR1467) $19.20
Tag for Starter/Generator, 12 Volt, Blank - Comes with 2 rivets. 2.5" long, .800" wide, 2" center to center rivet hole, .150" dia. rivet holes. Customer must stamp numbers. (Item #: 182606, Ref: DELCO12) $16.80
Voltage Regulator, 12 Volt - 4-terminal flat mount. The Three Post side of this regulator may be parallel or slightly splayed. Fits most 12V tractors and combines prior to 1957. (Item #: 105581, Ref: 182548M92) $25.00

Engine Gaskets
Silicone Blue RTV - Permatex ultra blue, no leak RTV silicone gasket, oil resistant, use on valve covers, oil pans, timing covers, water pumps. Temperature range -75 degree F to +500 degree F, 3.35 ounce tube. (Item #: 178141, Ref: PRM77BR) $10.90

Exhaust System
Chrome Exhaust Stack - Single Wall, 48 inches long with a slotted, 2 inch inside diameter inlet. This is a universal part. Verify Measurements before ordering. (Item #: 118823, Ref: ZNL89020C) $81.00
Chrome Exhaust Stack - Single Wall, 48 inches long with a slotted, 2.5 inch inside diameter inlet. This is a universal part. Verify Measurements before ordering. (Item #: 119038, Ref: ZNL89025C) $108.00
Chrome Exhaust Stack - Single Wall, 48 inches long with a slotted, 3.00 inch inside diameter inlet. This is a universal part. Verify Measurements before ordering. (Item #: 114858, Ref: ZNL89051C) $135.00
Chrome Exhaust Stack - Single wall, 53 inches long with a slotted, 3.00 inch inside diameter inlet with extended curve. This is a universal part. Verify measurements before ordering. (Item #: 173286, Ref: 146520CHR) $106.00
Chrome Exhaust Stack - Single wall, 53 inches long with a slotted, 3.50 inch inside diameter inlet. It has an extended curve on the outlet. This is a universal part. Verify measurements before ordering. (Item #: 173287, Ref: 146490CHR) $161.00
Chrome Exhaust Stack - Single Wall, 48 inches long with a slotted, 4.00 inch inside diameter inlet. This is a universal part. Verify Measurements before ordering. (Item #: 114945, Ref: ZNL89057C) $145.00
Chrome Exhaust Stack - Single Wall, 48 inches long with a slotted, 5.00 inch inside diameter inlet. This is a universal part. Verify Measurements before ordering. (Item #: 119080, Ref: ZNL89485C) $174.00
Chrome Exhaust Stack - Single Wall, 42 inches long with a slotted, 2.50 inch inside diameter inlet. This is a universal part. Verify Measurements before ordering. (Item #: 173281, Ref: L102236CHR) $88.00
Muffler Clamp, 1-1/4 - New Clamp for 1-1/4 inch outside diameter muffler inlet. (Item #: 182682, Ref: MC114) $2.10
Muffler Clamp, 1-3/4 - New Clamp for 1-3/4 inch outside diameter muffler inlet. (Item #: 108866, Ref: MC134) $4.80
Muffler Clamp, 1-3/8 - New Clamp for 1-3/8 inch outside diameter muffler inlet. (Item #: 182687, Ref: MC138) $2.90
Muffler Clamp, 2-1/4 - New Clamp for 2-1/4 inch outside diameter muffler inlet. (Item #: 108870, Ref: MC214) $5.30
Muffler Clamp, 2-3/4 - New Clamp for 2-3/4 inch outside diameter muffler inlet. (Item #: 108872, Ref: MC234) $8.71
Muffler Clamp, 3 - New Clamp for 3 inch outside diameter muffler inlet. (Item #: 108873, Ref: MC300) $7.40
Muffler Clamp, 3-1/2 - New Clamp for 3-1/2 inch outside diameter muffler inlet. (Item #: 108874, Ref: MC312) $8.00
Muffler Clamp, 4 - New Clamp for 4 inch outside diameter muffler inlet. (Item #: 108875, Ref: MC400) $8.30
Muffler Clamp, 5 - New Clamp for 5 inch outside diameter muffler inlet. (Item #: 118841, Ref: MC500) $12.70
Rain Cap - This rain cap is for a 1.750 inch pipe. (Item #: 108632, Ref: R1799) $11.00
Rain Cap - This rain cap is for a 2.0 inch pipe. (Item #: 108633, Ref: R1800) $8.80
Rain Cap - This rain cap is for a 2.50 inch pipe. (Item #: 108635, Ref: R1802) $12.50
Rain Cap - This rain cap is for a 2.750 inch pipe. (Item #: 108636, Ref: R1804) $11.00
Rain Cap - This rain cap is for a 4.0 inch pipe. (Item #: 108645, Ref: R1807) $12.90
Rain Cap - This rain cap is for a 4.50 inch pipe. (Item #: 108749, Ref: WC14) $13.40
Rain Cap - This rain cap is for a 5.0 inch pipe. (Item #: 108750, Ref: WC15) $17.40
Stainless Steel Clamp, 2.75 Inch - This Stainless Steel Clamp is used with Chrome Stacks and in other applications. (Item #: 179749, Ref: ZNL90872A) $6.50
Stainless Steel Clamp, 4 Inch - This Stainless Steel Clamp is used with Chrome Stacks and in other applications. (Item #: 185428, Ref: ZNL90875A) $8.50

Fuel System / Air Intake
Air Cleaner Filler - Fits many air cleaners that use steel wool type filler. Custom manufactured mesh. 1 bag = 3-1/2 inch x 3-1/4 inch. (Item #: 151026, Ref: S.43231) $14.00
Fuel Tank Screen - This Fuel Tank Screen is used with most stem-type sediment bowls to further protect against debris in the gas line. It has a 0.216 inch Insert Pipe outside diameter - 2.53 inch Overall Length. (Item #: 114940, Ref: R7949) $9.92
Main Fuel Valve - This main fuel valve replaces the original fuel solenoid for International carburetors. The original fuel solenoids are very unreliable and can easily be replaced with this manual valve. This assembly contains: the valve, graphite packing, and packing nut. Used on Carburetors: 50981DC, 45108DB, 50983DC, 52814DA, 47387DC, 361525R92, 358065R92, 362173R92, 367259R92, 380956R91, 380956R92, 380956R93, 381983R91, 381984R95, 389511R92, 367258R92, 396966R91, 388296R91, 388424R96, 396197R96, 396198R92, 381419R91, 397224R93, 381420R91, 357231R91, 356948R92. Replaces 47404DA, 374327R1, 362526R1, 362525R1 (Item #: 117537, Ref: 47404DASSY) $30.10
Sediment Bowl Gasket, 2-1/8 inch - For bowls with 2-1/8 inch diameter, 2.150 inch outside diameter. Made in the USA. (Item #: 112364, Ref: C1778R) $3.30

Gauges
No Picture Amp Gauge - This amp gauge comes with the "IH" logo printed on the face. It has a black face, chrome bezel, and reads 60-0-60. (Item #: 178963, Ref: IHS1837) $30.00
No Picture Hourmeter - DC voltages from 12 volt thru 36 volt nominal. Heavy duty glass-reinforced polyester body. Internal shock shields and grommets protect movement from shock and vibration damage. Fits 2-1/4 inch opening, three (3) mounting screws with nuts and two (2) blade terminals included. (Item #: 178318, Ref: HM771) $63.00
Hourmeter, Analog - 2 inch, black. Can be used on any tractor with a 12 to 24 volt electrical system. (Item #: 178285, Ref: S.52672) $42.30
Oil Gauge - For IHC and Farmall tractors 1947 and and up. Oil Pressure Gauge with color band - Includes mounting bracket. Has IH logo on face. (Item #: 110849, Ref: 41934DB) $49.57
Oil Line Adapter - Oil Gauge fittings may be different even for the same models. Here is an Oil Line Adapter if you have a gauge line without removable fittings, this converts 1/8 inch pipe thread to 1/8 inch tube. Brass. (Item #: 179540, Ref: 919095) $16.00

Hitch / Drawbar
Conversion Tong - Two Point Conversion Tong straight left hand Tong with combination Cat. I and Cat. II Ball. For converting IHC Two Point Fast Hitch to Three Point. About 28 inches overall length. (Item #: 184153, Ref: FH1447) $364.00
Conversion Tong - Two Point Conversion Tong straight right hand Tong with combination Cat. I and Cat. II Ball. For converting IHC Two Point Fast Hitch to Three Point. About 28 inches overall length. (Item #: 184167, Ref: FH1448) $364.00
Conversion Tong - Two Point Conversion Tong bent type, and Cat. II Ball. Left Hand. For converting IHC Two Point Fast Hitch to Three Point. About 32 inches overall length. (Item #: 179611, Ref: FH14416) $439.00
Conversion Tong - Two Point Conversion Tong bent type, right hand Tong with combination Cat. I and Cat. II Ball. Right Hand. The Bent Type spaces out at 32 inches between the ends of the tongs. The Non-Bent Type spaces out at 26 inches between the ends of the tongs. For converting IHC Two Point Fast Hitch to Three Point. About 32 inches overall length. (Item #: 179008, Ref: FH14417) $439.00
Hair Pin Assortment - 15-piece assortment. Includes four (4) of HP-3 (wire diameter 3/16 inch, length 3.75 inch), four (4) of HP-4 (wire diameter 5/32 inch, length 2 15/16 inches), four (4) of HP-5 (wire diameter 1/8 inch, length 2 9/16 inches), and three (3) of HP-6 (wire diameter 3/32 inch, length 1 5/8 inches). (Item #: 182461, Ref: HPA15X) $11.40
Universal Drawbar Lock - For Cat. 1 drawbars up to 1 1/2 inch thick and 3 inches wide. Prevents drawbar from rotating. (Item #: 112156, Ref: DBL2) $37.00

Hydraulic System
Filter Element - 25 Micron replacement element for SF1-25. (Item #: 182541, Ref: 1A9023) $15.40
Filter Element - 10 Micron replacement element for SF1-10. (Item #: 120092, Ref: 1A9021) $13.60
Hydraulic Hose Assembly-NPT, 12 inch - Universal. 12 inch overall length. 1/2 I.D. 2 Wire. Solid Male 1/2 NPT thread on both ends. (Item #: 118257, Ref: H42-2M-12) $11.00
Hydraulic Hose Assembly-NPT, 180 inch - Universal. 180 inch (15 Feet) overall length. 1/2 inch inside diameter. 2 Wire. Solid Male 1/2 inch NPT thread on both ends. (Item #: 179906, Ref: H42-2M-180) $55.50
Hydraulic Hose Assembly-NPT, 24 inch - Universal. 1/2 inch I.D. double wire braid (SAE-2R) with 1/2 inch NPT solid male fittings both ends. 24 inch overall length. Replaces OEM # - 407435R1. (Item #: 118256, Ref: H42-2M-24) $14.10
Hydraulic Hose Assembly-NPT, 30 inch - Universal. 30 inch overall length. 1/2 I.D. 2 Wire. Solid Male 1/2 NPT thread on both ends. (Item #: 118259, Ref: H42-2M-30) $16.10
Hydraulic Hose Assembly-NPT, 48 inch - Universal. I.H.C.: 1/2" I.D. double wire braid (SAE-2R) with 1/2" NPT solid male fittings both ends. 48" overall length. Replaces OEM # - 407437R1. Hydraulics: 48 inch overall length (Item #: 118261, Ref: H42-2M-48) $16.50
Universal Pressure Gauge, Hydraulic - 1000 Lb. Gauge. Glycerin Filled. Stainless Steel Case 2-1 2 diameter. Nickel silver movement accurate to within 2%. Dual range KPA-PSI. Plexiglass crystal. 1 4 NPT male brass fitting. (Item #: 172285, Ref: GG1000) $13.50
Universal Pressure Gauge, Hydraulic - 60lb Gauge. Glycerin Filled. Stainless Steel Case 2-1/2 diameter. Nickel silver movement accurate to within 2%. Dual range KPA-PSI. Plexiglass crystal. 1/4 NPT male brass fitting. (Item #: 172338, Ref: GG60) $13.91

Implements
Axle Bolt - Axle bolt, 1 each (Ref 3). Used on many Bush Hog rotary cutters. Used on models 12, 104, 105, 109, 126, 205, 255, 275, 285, 305, 306, 307, 405, 405HR, 406, 406HR, 502, 600, 1050, 1051, 1109, 1126, 1207, 1209, 1226, 1306, 1307, 1405, 1406, 2510, 2512, 3108, 2309, BD90, FH162, S268, SM60, SQ36 (Item #: 170217, Ref: BH1317) $14.90
Axle Bolt - Axle bolt, 1 each (Ref 3). Used on many Bush Hog rotary cutters. Used on models 12, 104, 105, 109, 126, 205, 255, 275, 285, 305, 306, 307, 405, 405HR, 406, 406HR, 502, 600, 1050, 1051, 1109, 1126, 1207, 1209, 1226, 1306, 1307, 1405, 1406, 2510, 2512, 3108, 2309, BD90, FH162, S268, SM60, SQ36 (Item #: 170217, Ref: BH1317) $14.90
Bearing cone (L44643) - For Caster Assembly, requires 2.Used on many Bush Hog rotary cutters. Used on models 12, 104, 105, 109, 126, 205, 255, 275, 285, 305, 306, 307, 405, 405HR, 406, 406HR, 502, 600, 1050, 1051, 1109, 1126, 1207, 1209, 1226, 1306, 1307, 1405, 1406, 2510, 2512, 3108, 2309, BD90, FH162, S268, SM60, SQ36, SQ480, SQ600. (Item #: 114630, Ref: 22) $5.90
Bearing Cup - This part fits Caster Assembly (Part Number BH215, Ref #6). Sold individually, two used per caster assembly. Used on many Bush Hog rotary cutters. Used on models 12, 104, 105, 109, 126, 205, 255, 275, 285, 305, 306, 307, 405, 405HR, 406, 406HR, 502, 600, 1050, 1051, 1109, 1126, 1207, 1209, 1226, 1306, 1307, 1405, 1406, 2510, 2512, 3108, 2309, BD90, FH162, S268, SM60, SQ36. Also replaces 132709, 15191, 32190M1, L44610. (Item #: 169771, Ref: 170BH) $7.86
Caster Assembly - Tail wheel and hub assembly with grease fitting and fork assembly. Shaft on Yoke is 1-1/2 inches diameter, 8 inches overall length, 7-1/4 inch to pin hole. New style tail assembly, used on the following Bush Hog cutters: 12, 104, 105, 109, 126, 205, 255, 275, 285, 305, 306, 307, 405, 405HR, 406, 406HR, 502, 600, 1050, 1051, 1109, 1126, 1207, 1209, 1226, 1306, 1307, 1405. Wheel must be attached to fork. For Bush Hog cutters with SPB40 spacer (included), assembly will also replace all models with Timken bearings. (Item #: 173612, Ref: 12269) $183.00
Caster Assembly, Old Style - Tail Wheel and Hub Assembly with grease fitting. 4 x 8 inch rim, 15 inch outside diameter of wheel. Includes wheel, hub, axle bearing and bolt assembly. OLD style tail assembly used on the following Bush Hog cutters: 12, 104, 105, 109, 126, 205, 255, 275, 285, 305, 306, 307, 405, 405HR, 406, 406HR, 502, 600, 1050, 1051, 1109, 1126, 1207, 1209, 1226, 1306, 1307, 1405, 1406, 2510, 2512, 3108, 2309, BD90, FH162, S268, SM60, SQ36, SQ480, SQ600. Wheel must be attached to fork. For Bush Hog cutters. With SPB40 spacer, assembly will also replace all models with Timken Bearings (Ref #1-#11). (Item #: 161111, Ref: BH215) $132.00
Hub Assembly - Hub with bushings (3/4 inch), wheel bolts (4), and grease fitting. Center tube length 5 inches. For rotary cutters: RB60 with new style 1-1/4 inch diameter caster, SM60R, SM160R; Squealer models: 1207, SQ36, SQ48, SQ60, SQ72, SQ148, SQ480. Replaces 60978, 60990, 63812. Can use 500BH tail wheel. (Item #: 180514, Ref: 63813BH) $38.10
Hub with Bearing Cups - 4-bolt, 5 inch bolt circle and 3-5/8 inch wheel pivot hub with bearing cups (1 inch axle) (Ref #5). This part fits caster assembly (part number BH215). Used on many Bush Hog rotary cutters. Used on models 12, 104, 105, 109, 126, 205, 255, 275, 285, 305, 306, 307, 405, 405HR, 406, 406HR, 502, 600, 1050, 1051, 1109, 1126, 1207, 1209, 1226, 1306, 1307, 1405, 1406, 2510, 2512, 3108, 2309, BD90, FH162, S268, SM60, SQ36. (Item #: 182627, Ref: BH1311) $49.30
No Picture Round Bale Tine 31.5 Inches - Fully Hardened. Also replaces Kverneland 221151. (Item #: 182589, Ref: 221129) $51.00
No Picture Round Bale Tine 31.5 Inches - Fully Hardened. Also replaces Kverneland 221151. (Item #: 182589, Ref: 221129) $51.00
No Picture Round Bale Tine 38.5 Inches - Fully Hardened. Also replaces Kverneland 241107, 241161. (Item #: 182592, Ref: 241100) $91.48
No Picture Round Bale Tine 43 Inches - Fully Hardened. (Item #: 182594, Ref: 241166) $111.54
No Picture Round Bale Tine 49 Inches - Fully Hardened. (Item #: 152690, Ref: 241162) $78.00
No Picture Round Bale Tine 55 Inches - Fully Hardened. (Item #: 182593, Ref: 241163) $131.61
Seal, Caster - Seal, 2 required (Ref #2). Used on many Bush Hog rotary cutters. Used on models 12, 104, 105, 109, 126, 205, 255, 275, 285, 305, 306, 307, 405, 405HR, 406, 406HR, 502, 600, 1050, 1051, 1109, 1126, 1207, 1209, 1226, 1306, 1307, 1405, 1406, 2510, 2512, 3108, 2309, BD90, FH162, S268, SM60, SQ36, SQ480, SQ600. (Item #: 180300, Ref: 30BH) $4.30
Tail Wheel Assembly - 4 inch x 8 inch tail wheel assembly with laminated tire. 3-5/8 inch pilot, 4 bolt holes, 5 inch bolt circle, 3-3/4 inches wide, 15 inch outside diameter. Used on the following Bush Hog cutters: 12, 104, 105, 109, 126, 205, 255, 275, 285, 305, 306, 307, 405, 405HR, 406, 406HR, 502, 600, 1050, 1051, 1109, 1126, 1207, 1209, 1226, 1306, 1307, 1405 and 1406, 2510, 2512, 3108, 3209, BD90, FH162, S268, SM60, SQ36, SQ480, SQ600. Replaces Sidewinder 15205, Servis Rhino 373024H, Terrain King 373024H, Modern 401-0048, BMB 5337, Hardee C40-RC, King Kutter KK4X8. (Item #: 111222, Ref: 500BH) $56.00
No Picture Talc Powder Lubricant - Dry Talc powder lubricant, 8 lb container. Absorbs moisture and keeps treated seed from sticking together in planter boxes. Recommended application rate: 3 oz. Coverage: Typically treats 60-80 acres. (Item #: 107928, Ref: TP19000TP) $22.10