Posted by willie in mn on March 11, 2011 at 02:08:40 from (205.188.116.74):
In Reply to: Gas went down posted by iagary on March 10, 2011 at 18:23:39:
Pine County Mn, was 3.60/9 last Fri, Mon dropped a penny, Thur dropped another nickel to 3.54/9. Opinion- I don't have a dog in the fight except that I have to pay whatever the price happens to be. Please don't shoot the messenger, just forwarding information. No quarrel with the local station owners either. Not much profit margin on gas, makes his most profit on other stuff in the store while you are there, called convenience. Local stations have to pay when getting delivery, no credit plan with supplier. If his costs go up, he has to raise his selling price or go out of business. If he goes out of business, where do we buy our gas? Now good, bad, or otherwise, here we have state rules that the local station cannot sell at less than his cost. Eg: the numbers are wrong, but show the point. Station pays 3.39 for a load of gas, has to charge at least that much. His next load costs 3.45, he has to pay when delivered. If his next load costs 3.24, he still has some 3.45 gas in his tanks & has to charge at least that much until that many gallons is gone. Reason for the minimum price- many years ago high volume stations with deep pockets would cut price below cost to drive the small "Mom-Pop" stations out of competition, then bump the price way up. So state lawmakers passed a rule that prohibit selling below cost. Don't know if it actually worked as intended or not, but that's the way it is now. Willie P.S. cut my gas use a bit last couple months. Parting out my 20 year old, 5800# Belchfire V8 van, now driving 2500# V6.
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]
Today's Featured Article - Product Review: JB Weld - by Staff. JB Weld is basically an epoxy glue that does an exceptionally good job of bonding to cast iron and steel along with several other materials. As I mentioned, it is so common that I have yet to buy a tractor that did not have JB Weld used somewhere. It is sometimes used so well you can't tell its there and other times used as a sloppy quick fix. Finding where and how it can be used correctly is key to whether you are using it as an "inelegant hack" or an integral solution to difficult and expens
... [Read Article]
Latest Ad:
WANTED Front grille/nose assembly for Massey Ferguson 1160 (also fits 1180 & 1190). Headlight-mount section. AGCO Grille 3706022M91 (supersedes 3705942M91), cover 3705494M1/M2, holders 3705501M91/3711158M92. New/NOS/good used OK. Jonesboro, AR - will pay shipping. Photo appreciated. Thanks
[More Ads]
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy
TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
