Posted by pburchett on January 05, 2011 at 09:35:50 from (170.185.166.19):
Does anyone heat with a Clayton 1800 Warm Air Furnace which is made by US Stove?
I have one in the basement that is connected to our air handler in the attic via a 12 inch insulated duct. The stove connects to 4 ft of 6 inch stove pipe, then to 24ft of 6 inch double wall insulated stainless steel flue with 5 feet sticking out the roof. I normally heat 3850sq/ft (4700sq/ft if I open the basement doors to the garage) to 73-75F most of the winter, and burn all the wood you can get on a large wheelbarrow every 24 hours. The house is insulated well (R21 in the basement walls, R13 in basement ceiling , R15 upstairs walls and R50 in upstairs ceiling). QUESTION 1: Does this sound like an excessive amount of wood to burn per day?
The stove drafts more than fine but creosote build up is sometimes a problem when trying to choke it down early or late in the heating season. I have installed a fresh air vent which is located above the stove. I do not use the forced air draft and only let if draft naturally by opening the two dampers that are located on the ash door and below the fuel door. QUESTION 2: Which is best for combustion (A) air entering below the fire through the ash pan and up through the grates or (B) air entering at the height of the fuel?
The stove has a selectable secondary heat exchanger which brings the exhaust to the front of the stove then up through a tunnel to the back of the stove then out the flue. I can not tell much difference in the heating capabilities with the secondary heat exchanger selected, but it does tend to creosote more. QUESTION 3: Do I just need to burn the stove hotter to eliminate the creosote while using the secondary heat exchanger?
The blower on the stove is automatic and has an output switch to select the speed of 1100, 1250, or 1400 CFM. QUESTION 4: Which speed would be best to move the heat around (does a faster air speed cool the air)?
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]
Today's Featured Article - Trailering Your Tractor - by Curtis Von Fange. One of the fun things of summer and fall are the parades and tractor shows that go on across America. Many owners of tractors travel long distances to attend these shows and they usually take their restored iron along with them. Safe trailering practices and inspections will ensure that the event is a fun one. A good habit to develop when using a trailer is to give that �quick look over� before taking it on a trip. Before hooking up to it check the tongue for proper operation. The latche
... [Read Article]
Latest Ad:
1965 International Harvester McCormick Farmall cub tractor 2,500. Two owner tractor. My grandfather bought new in 1966, then we inherited it. Have all the paperwork original manual and all maintenance records. It starts and moves. Comes with underbelly mower, plough, and some other attachments.
[More Ads]
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy
TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
