Posted by John T on March 05, 2010 at 17:48:35 from (71.55.30.174):
In Reply to: OT 240V outlet posted by 550Doug on March 05, 2010 at 16:05:40:
Okay, heres the deal:
1) Can you use an existing outlet??????
The answer is MAYBE but I wouldnt bet too much since the new set up may require more amps then the old stove PLUS it may require 120/240 (4 wire) instead of straight 240 (3 wire) as many older stoves were set up!!!!!!!!!!!! In the old days they only ran 3 wires (2 hots 1 ground) to stoves, but nowadays many require 120 and 240 so they run 4 wires (2 hots, 1 Neutral, 1 Ground) PLUS the new set up may require more current then the old ALL MUST BE CORRECT amperage and type and poles of receptacle
QUESTIONS FOR YOU: What TYPE (amps, poles) Receptacle does the old stove have and what is on the new set up??????????????????????? If they are the same (amps and poles) you can likely use whats there BUTTTTTTTTT if the new set up requires a higher amp service and/or different receptacle (poles OR amps) then you need to upgrade
a) For a stove branch circuit you will need:
1)The correct ampacity i.e. the correct sized circuit breaker in the panel,,,,,,
2) The correct size and number (3 or 4) feed wires from the panel to the receptacle,,,,,,,,
3) The correct size receptacle (i.e. 40 or 50 or 60 amps etc)
4) The correct receptacle like a 3 pole or a 4 pole (plus correct amp rating). Old stoves often used a 3 pole, 2 hots and a ground, new stoves may use 120/240 so they requires 4 pole receptacles, 2 hots, Neutral, Ground
SOOOOOOOO once you know the new set ups amps,,,,,,,,,the receptacle (poles and amps) it uses,,,,,,,,,whats there now (poles and amps)
THE ANSWER CAN BE DETERMINED
If I missed anything hopefully the gents with more current experience can add to this as Im a long retired as an electrical distribution engineer and rustyyyyyyyy as an old nail lol
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]
Today's Featured Article - Usin Your Implements: Bucket Loader - by Curtis Von Fange. Introduction: Dad was raised during the depression years of the thirties. As a kid he worked part time on a farm in Kansas doing many of the manual chores. Some of the more successful farmers of that day had a new time saving device called a tractor. It increased the farm productivity and, in general, made life easier because more work could be done with this 'mechanical beast'. My dad dreamed that some day he would have his own tractor with every implement he could get. When he rea
... [Read Article]
Latest Ad:
For sale Farmall super A tractor is complete and has just been setting for awhile,it was running when pulled out of the barn,shouldn’t take to much to get it going asking 1100.00
[More Ads]
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy
TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
