Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 
Marketplace
Classified Ads
Photo Ads
Tractor Parts
Salvage

Community
Discussion Forums
Project Journals
Your Stories
Events Calendar
Hauling Schedule

Galleries
Tractor Photos
Implement Photos
Vintage Photos
Help Identify
Parts & Pieces
Stuck & Troubled
Vintage Ads
Community Album
Photo Ad Archives

Research & Info
Articles
Tractor Registry
Tip of the Day
Safety Cartoons
Tractor Values
Serial Numbers
Tune-Up Guide
Paint Codes
List Prices
Production Nbrs
Tune-Up Specs
Torque Values
3-Point Specs
Glossary

Miscellaneous
Tractor Games
Just For Kids
Virtual Show
Museum Guide
Memorial Page
Feedback Form

Yesterday's Tractors Facebook Page

  
Tractor Talk Discussion Board

Re: Cylinder Ridge


[ Expand ] [ View Replies ] [ Add a Reply ] [ Return to Forum ]

Posted by Buzzman72 on February 18, 2010 at 06:33:11 from (74.129.194.33):

In Reply to: Cylinder Ridge posted by Paul from MN on February 17, 2010 at 14:47:47:

You say you had a cracked head. Like someone below, I'd also be concerned about coolant getting into the oil and taking out the bearings.

I was working in the parts department at a Ford dealership when Ford came out with the head gasket recall on the 3.8 V6's. The first repair was strictly a head gasket replacement, after cleaning the head and block surfaces [often with the heads being resurfaced, if there had been any warpage] and a total fluid change...and 9 times out of 10, engines that weren't knocking when they came in with bad head gaskets would begin knocking after the head gasket replacement. These cars then would get a replacement engine, and the bearing damage was caused by coolant getting into the oil...and I'm not talking about a gallon, or even a quart of coolant in the oil.

The other side of the coin is that I recall Pappy and Grand-dad doing a valve job on a private contractor's mail truck with a small block Ford V8. The engine had well over 200,000 miles on it, and Pappy had tried to steer the customer towards a full overhaul. But he was not in a position to pay or anything more than the valve job [this was in the mid-1970's,and the way gas prices had risen, he'd ended up bidding the job WAY too cheap]. So it was agreed that Pappy and Grand-dad would do the valve job, and there was NO WARRANTY on that engine afterwards. Within 30 days [they were running the mail 7 days a week then], that engine was smoking like he was fogging for mosquitoes. The lack of compression leaks on the top side had put more pressure on the piston rings, and since they were already weak, they failed.

Not saying any of this will happen to you...but by rolling the dice, are you prepared, financially AND mentally, if you lose your bet and have to tear it all back down and do it "right" ??It's YOUR tractor, and you have every right to do whatever you want with it. Just be aware of possible consequences. Not EVERY bank robber goes to jail; that's why some folks take the risk. Sometimes someone gets lucky...and in the case of this engine, you may be one of the lucky ones. It's your tractor, your time, and your money.


Replies:




Add a Reply

:
:
:

:

:

:

:

:

:

Advanced Posting Options

: If you check this box, email will be sent to you whenever someone replies to this message. Your email address must be entered above to receive notification. This notification will be cancelled automatically after 2 weeks.



 
Advanced Posting Tools
  Upload Photo  Select Gallery Photo  Attach Serial # List 
Return to Post 

TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Today's Featured Article - The Nuts and Bolts of Fasteners - Part 2 - by Curtis Von Fange. In our previous article we discussed capscrews, bolts, and nuts along with their relative hardness and thread sizes. In this segment we will finish up on our fasteners and then work with ways to keep them from loosening up in the field. Capscrews, bolts and nuts are not the only means of holding two parts together. When dealing with thinner metals like sheet tin, a long bolt and ... [Read Article]

Latest Ad: Oliver 550 Diesel runs like a watch three point hitch pto engine gone threw about two hundred hours ago nice clean tractor [More Ads]

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy