Posted by jdemaris on August 25, 2009 at 06:41:10 from (67.142.130.16):
In Reply to: 6.5 chevy diesel posted by Bryan in Iowa on August 25, 2009 at 05:46:22:
There is no proper "rebuild" process for a 6.5. So, I'm curious what exactly was done.
The block is pretty much the same as the later 6.2s and prone to cracking at the main-bearing webs once it gets over 200K miles. The crank is never supposed to be ground since when new, the journals are surface-hardened. It is also only cast-iron instead of the forged steel, like just about every other diesel in the world uses. The heads are lightweight and prone to cracking if overfueled and/or overheated. So, I'd make sure to ask what specifically was done to it.
I've been using 6.2s and 6.5s for years, but also understand their severe limitations for HD use. I would not drive any 6.2 or 6.5 long distance if it has over 150K without pulling the oil pan and inspecting for main-bearing web cracks. One note: sometime around 1998 GM addressed the block cracking problem and made the outside bolts on the main-bearing caps smaller. Made them 10 mm instead of 12 mm. So, if you have 10 mm outside bolts, you've got the stronger block.
If you want a reliable and older diesel puller, get a Dodge with a 5.9 Cummins, or to a lesser degree, a Ford with an IH 7.3 IDI turbo (up to mid 1994), or a later 7.3 DI Powerstroke. Both are worlds better for heavy use, than the 6.5 can ever be. Except: There are now new 6.5s being built with beefed up and high alloy blocks, heavier Chinese heads, and forged steel crankshafts. Sometimes called "Optimizer 6500s" and they cost a fortune. Mostly sold for HUMVEE replacement engines or for marine use.
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]
Today's Featured Article - Talk of the Town: The Saga of Grandpa's Tractor - by The following saga is from the Tractor Talk Discussion Forum. Someone. The saga starts with the following message: Hey guys I have a decision to make. I know what you all will probably suggest and it will probably agree with me way down inside, but here it is. I have a picture blown up and framed in my "tractor room" of a Farmall M. It was my Grandpa's tractor, of which whom I never got to meet. He froze to death getting this tractor out of the barn to pull a truck out of the ditch before I was born. Anyway my dad and aunt had to sell it at the auction,
... [Read Article]
Latest Ad:
Sell 1958 Hi-Altitude Massey Fergerson tractor, original condition. three point hitch pto engine, Runs well, photos available upon request
[More Ads]
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy
TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.