Posted by rvirgil_KS on March 29, 2009 at 20:15:04 from (72.214.203.115):
In Reply to: 6 0r 12 volt? h posted by javan on March 29, 2009 at 18:16:43:
If I understand your first post, there is presently no battery in the tractor. Your second post indicates a distributor, not a mag.
Here are some ways to determine 6 or 12 volt, + or - ground:
1. Does it have an alternator? If so it's 12 volts and negative ground.
2.Does it have a Delco generator?
If yes, does the F (field wire) on the generator go up to the light switch? If so it's probably 6 volt.
If the F (field wire) goes to a regulator, is the voltage and polarity stamped on the cover of the regulator?
Is there a tag on the side of the generator? Black tag is 6 volt, red tag is 12 volt.
3. If you have an ohm meter, measure the resistance across the + and - terminals on the coil. Less than 2 ohms it's a 6 volt coil, more than 3 ohms it's a 12 volt coil.
If it's a 6 volt coil is there a resistor (ceramic device about 1/2 in. square and 2 to 3 in. long)in the wire going from coil to switch? If so it has probably been converted to 12 volt.
4. To determine polarity or ground:
With battery connected and engine not running, turn on lights or ignition. Ammeter should swing slightly negative. If ammeter does not move jumper the wire between coil and distributor to ground (switch on). This simulates closed points and may be easier than removing distributor cap. Negative swing, OK. Positive swing reverse the battery connections.
Wire from distributor to coil should match battery ground. (Positive ground, distributor wire connects to + on coil. Negative ground it connects to - on coil.)
If it has a generator I would polarize it when I get the battery in it's correct connection.
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]
Today's Featured Article - 12-Volt Conversions for 4-Cylinder Ford 2000 & 4000 Tractors - by Tommy Duvall. After two summers of having to park my old 1964 model 4000 gas 4 cyl. on a hill just in case the 6 volt system, for whatever reason, would not crank her, I decided to try the 12 volt conversion. After some research of convert or not, I decided to go ahead, the main reason being that this tractor was a working tractor, not a show tractor (yet). I did keep everything I replaced for the day I do want to restore her to showroom condition.
... [Read Article]
Latest Ad:
1958 FORD RARE 4x4 801 TRACTOR, ELENCO/FRONT DRIVE, FRONTLOADER AND WEIGHTED REAR WHEELS, FIVE SPEED, LIVE PTO, GAS ENGINE, NEW REAR WHEELS AND TIRES, ENGINE RUNS.
[More Ads]
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy
TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
