|
Tractor Talk Discussion Board |
Re: A SURE WAY TO REMOVE FLAKY RUST FROM EXHAUST MANIFOLDS AND BRAKE DRUMS
[ View Follow Ups ] [ Post Followup ] [ Return to Tractor Talk Discussion Board ]
Posted by Lyndsay on March 30, 2000 at 14:51:51 from (209.117.43.192):
In Reply to: A SURE WAY TO REMOVE FLAKY RUST FROM EXHAUST MANIFOLDS AND BRAKE DRUMS posted by Ken McWilliams on July 21, 1998 at 09:50:41:
: Back several years ago when I was restoring '60's muscle cars, a car restoration company called "The Eastwood Company" carried all kinds of tools and supplies for auto restoration. They had a chemical that would remove all rust from steel or cast iron. I used it, but it was expensive. : I found that if I would take muratic acid, the kind sold in paint stores for etching concrete, and diluting it about 4 to 1, I could soak rusty steel or cast iron in it several days and remove all rust down to the gray matte finish of the iron or steel. : I cleaned exhaust manifolds, brake drums, head light housings, brackets, linkages, etc and the object would be bare steel or cast iron after soaking. I would use a new 30 gallon garbage can for my chemical tank and let the parts soak for days in the muratic acid. Any aluminum, copper or brass, however will be readily attacked and be eaten in a few minutes or few hours with rather vigorous foaming. So don't put any of these metals into the muratic mixture. : I would remove the part from the muratic and have to immediately rinse/neutralize, dry and give it a coat of paint, because you could see the part literally turn orange from new rust forming before you. : This solution could be used many times and be restrengthened with additions of muratic as the old was depleted. There is a limit, but it's after lots of parts. : In our county, there is a semi-annual chemicals collection and disposal where you can take cans of paint, cleaning chemicals etc. : Try it, you may like it, but be careful acid burns are very painful. : KRM I would like to know if this method works on nails(non-galvanized).
Follow Ups:
Home
| Forums
| Order Support
Today's Featured Article -
12-Volt Conversions for 4-Cylinder Ford 2000 & 4000 Tractors - by Tommy Duvall. After two summers of having to park my old 1964 model 4000 gas 4 cyl. on a hill just in case the 6 volt system, for whatever reason, would not crank her, I decided to try the 12 volt conversion. After some research of convert or not, I decided to go ahead, the main reason being that this tractor was a working tractor, not a show tractor (yet). I did keep everything I replaced for the day I do want to restore her to showroom condition.
... [Read Article]
Latest Ad:
1958 FORD RARE 4x4 801 TRACTOR, ELENCO/FRONT DRIVE, FRONTLOADER AND WEIGHTED REAR WHEELS, FIVE SPEED, LIVE PTO, GAS ENGINE, NEW REAR WHEELS AND TIRES, ENGINE RUNS.
[More Ads]
Copyright © 1997-2026 Yesterday's Tractor Co. All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V. Yesterday's Tractors - Antique Tractor HeadquartersWebsite Accessibility Policy |
|