Posted by Mark - IN. on March 08, 2008 at 19:25:16 from (205.188.117.74):
In Reply to: OT air compressors posted by Lanse on March 08, 2008 at 17:39:32:
Lanse, if you're going to run tools with it, its going to need a sufficient air supply/reserve (tank) or else you'll run the pump to death and you'll never maintain a constant or even flow of pressure to your tools. The same holds true even more so if you're going to be painting with it. Also, you need to be concerned with house wiring and current draw...house wiring gets hot, and so does the pump if it hasn't got sufficient current flow. First figue out what your service is to the outlet you'll be using (10amp, 20amp, 30amp?) before you decide on anything. Once you know that, figure out how often or what you'll be using it for, and go from there.
I once inherited a compressor that had two 2HP heads, drier, and 100 gallon tank. It was 208 3-phase which is hardly residential or ag. It was nice too, but no use to me. I put wheels on it, rolled it to the road and put a sign on it that read "Free for the taking, I'll help you load it, don't bring it back". It was free to me, so I figure that I'd let someone else have it to ponder over...away from me. Now I've got a 5HP 220VAC unit on a 30amp double pole breaker in the barn with a 60 gallon tank and a smaller portable 11 gallon 6.3/3.6 CFM Coleman in the garage that draws 15amps on 110. As I recall, the Coleman cost me about $300 and the bigger Sears was about $1,000. They both have their places for their jobs. Somewhere I've got a tiny 2 gallon Cambell Housefeld that I bought from Walmart for like $100 for recharging the well tank so I didn't have to drag a house through the house, but after I saw "Made in China" on it, never used it again...dragged the hose through the house until finally went deep well. Maybe I threw it out too, I don't recall or know where anything is in the house...people keep moving and hiding stuff on me.
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]
Today's Featured Article - Product Review: JB Weld - by Staff. JB Weld is basically an epoxy glue that does an exceptionally good job of bonding to cast iron and steel along with several other materials. As I mentioned, it is so common that I have yet to buy a tractor that did not have JB Weld used somewhere. It is sometimes used so well you can't tell its there and other times used as a sloppy quick fix. Finding where and how it can be used correctly is key to whether you are using it as an "inelegant hack" or an integral solution to difficult and expens
... [Read Article]
Latest Ad:
1945 Farmall wide body gas with pto and front plow. Runs good but needs new points.
[More Ads]
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy
TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
