Posted by Billy NY on January 21, 2008 at 12:05:43 from (205.188.117.74):
In Reply to: hills posted by Bill from MA on January 21, 2008 at 10:49:44:
That is one of those judgement calls, that can be difficult to make an accurate assessment, what kind of tractor is the jd 2040, is it similar to the other row crops, anything like a 2010 or is it more like a utility type? (can't visualize what kind that model is)
I know the feeling well having been on a 2010 narrow front in a few places I'd like to forget about, that feeling is unique.
First thing is, no hill is worth mowing that will potentially turn over a tractor with you on it, even more so if it does not have a roll over protective structure and seat with seatbelt, designed and manufactured to keep you in place and not fail under load (crush, bend, break etc.) you stay in the seat and are not crushed by the tractor. Without that, it's russian roulette, goes over you lose.
Another thing I hate about hills, is the potential to free wheel, anyting prone to pop out of gear etc., can also be a factor, nice to have good brakes. Always remember fresh cut grass, weeds whatever is slippery, and that dew when the sun goes down is also just as slippery.
Best thing for hills is a low center of gravity utility sized tractor properly ballasted and or weighted down, or any similar piece of equipment designed for the purpose, vs a row crop or other higher center of gravity type of tractor.
Also not to lecture, but these hills can really get under your skin so to speak and test your nerve, I often look at areas I'd like to mow and just talk myself out of it, + all the unknowns, that new chuck hole on the down side wheels, who knows what, if it's unfamiliar turf, heavily over grown, anything is possible.
We have an abundance of hills here, actually not too far from the MA border about 25 miles, (I can see the berkshires from my house) and it's amazed me that in some of the fields I've been in, particularly a few from last year I noticed that some of the slopes certainly were not friendly to the larger higher center of gravity tractors commonly used. I loaded out hay, large sqaures and rounds out of those fields, and knowing that the big ford NH 8970 made it through there, still did not have me convinced, I skidded many bales to safer ground before picking and loading.
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]
Today's Featured Article - Ford Part Number Trivia - by Forum Participants. "Replaced by" means the part was superseded. All of my part books date back to 1964 and New Holland have changed some part numbers. They usually put the old Ford part number on the package. I was suppressed when I looked up the part number of the auxiliary drive shaft because for some reason the part number went through a radical change and it lost its "Basic Part Number". Ford part numbers follow the following rules. Most part numbers are in three parts. The middle part is called the
... [Read Article]
Latest Ad:
Sell 1958 Hi-Altitude Massey Fergerson tractor, original condition. three point hitch pto engine, Runs well, photos available upon request
[More Ads]
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy
TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.