|
Tractor Talk Discussion Board |
OT, can't remember my geometry, need formula
[ Expand ] [ View Replies ] [ Add a Reply ] [ Return to Forum ]
Posted by Leroy on August 03, 2007 at 14:46:41 from (209.143.52.120):
I lost the book I had all my geometry formulas in and now I need to find out quick how long the diagonal measurement of a triangle would be. The bottom is 125.0" long with a side of 171.5" and a 90* corner between these measurements. Need to layout foundation marks for backhoe tommorrow
Replies:
- THANKS TO ALL THAT REPLIED Leroy 18:55:53 08/03/07
(0)
- Re: OT, can't remember my geometry, need formula suptscottyb 17:11:47 08/03/07
(0)
- Re: OT, can't remember my geometry, need formula suptscottyb 17:09:58 08/03/07
(0)
- Re: OT, can't remember my geometry, need formula doug in illinois 15:23:18 08/03/07
(0)
- Re: OT, can't remember my geometry, need formula Ron in OH 15:15:52 08/03/07
(0)
- Re: OT, can't remember my geometry, need formula midwest redneck 15:14:18 08/03/07
(0)
- Re: OT, can't remember my geometry, need formula Jim.UT 15:12:16 08/03/07
(0)
- Re: OT, can't remember my geometry, need formula Greg_Ky 15:09:55 08/03/07
(2)
- OOPS Greg_Ky 15:15:38 08/03/07
(1)
- Re: OT, can't remember my geometry, need formula farmerweber in PA 14:59:19 08/03/07
(0)
- Re: OT, can't remember my geometry, need formula Blue3992 (N Illinois) 14:52:30 08/03/07
(0)
- Re: OT, can't remember my geometry, need formula JDB 14:51:24 08/03/07
(0)
Home
| Forums
| Order Support
Today's Featured Article -
Tractor Profile: Farmall M - by Staff. H so that mountable implements were interchaneable. The Farmall M was most popular with large-acreage row-crop farmers. It was powered by either a high-compression gas engine or a distillate version with lower compression. Options included the Lift-All hydraulic system, a belt pulley, PTO, rubber tires, starter, lights and a swinging drawbar. It could be ordered in the high-crop, wide-front or tricycle configurations. The high-crop version was called a Model MV.
... [Read Article]
Latest Ad:
1958 FORD RARE 4x4 801 TRACTOR, ELENCO/FRONT DRIVE, FRONTLOADER AND WEIGHTED REAR WHEELS, FIVE SPEED, LIVE PTO, GAS ENGINE, NEW REAR WHEELS AND TIRES, ENGINE RUNS.
[More Ads]
Copyright © 1997-2026 Yesterday's Tractor Co.
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V. Yesterday's Tractors - Antique Tractor HeadquartersWebsite Accessibility Policy |
|
