Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 
Marketplace
Classified Ads
Photo Ads
Tractor Parts
Salvage

Community
Discussion Forums
Project Journals
Your Stories
Events Calendar
Hauling Schedule

Galleries
Tractor Photos
Implement Photos
Vintage Photos
Help Identify
Parts & Pieces
Stuck & Troubled
Vintage Ads
Community Album
Photo Ad Archives

Research & Info
Articles
Tractor Registry
Tip of the Day
Safety Cartoons
Tractor Values
Serial Numbers
Tune-Up Guide
Paint Codes
List Prices
Production Nbrs
Tune-Up Specs
Torque Values
3-Point Specs
Glossary

Miscellaneous
Tractor Games
Just For Kids
Virtual Show
Museum Guide
Memorial Page
Feedback Form

Yesterday's Tractors Facebook Page

  
Tractor Talk Discussion Board

Re: crack in exhaust manifold M how to fix ?


[ Expand ] [ View Replies ] [ Add a Reply ] [ Return to Forum ]

Posted by ScottyHOMEy on July 26, 2007 at 19:37:07 from (70.105.246.111):

In Reply to: crack in exhaust manifold M how to fix ? posted by roger roland on July 26, 2007 at 18:51:56:

Is the crack in the intake or the exhaust side? By the middle do you mean the upright part -- still same question, exhaust or intake end?

I asked once, in dealing with a problem on another engine, about how much heat a brazed joint in a manifold could take and still hold, and never got a good answer.

About all I could surmise is that for just ordinary gettin' around without a big load, you *might* get away with brazing on the exhaust side, or near it. But if you're gonna work the tractor hard EVER, you're apt to just burn it out and be back where you started.

You may wind up with a replacement as the wisest choice, but also try to figure out how it cracked.

(Somebody else chime in here if I'm wrong, please) On the As, Bs, and Cs, the manifold has cuts in between the ports where it faces up to the block. These cuts run right through the holes for the studs. And those studs have washers to go under the nuts. Only the studs at each end of the manifold are tightened down without these washers. This is so that the manifold, even when torqued down correctly, can expand and contract without breaking.

Whatever your solution, patch or replace, if your manifold has these same cuts in it, make sure you've got those manifold washers in place when you put the nuts on it. It'll make for less stress on the braze and, if their absence was the cause of it cracking in the first place, perhaps prevent a repeat performance with a new manifold.


Replies:




Add a Reply

:
:
: :

:

:

:

: If you check this box, email will be sent to you whenever someone replies to this message. Your email address must be entered above to receive notification. This notification will be cancelled automatically after 2 weeks.


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Today's Featured Article - History of the Nuffield Tractor - by Anthony West. The Nuffield tractor story started in early 1945. The British government still reeling from the effects of the war on the economy, approached the Nuffield organization to see if they would design and build an "ALL NEW" British built wheeled tractor, suitable for both British and world farming. ... [Read Article]

Latest Ad: Oliver 550 Diesel runs like a watch three point hitch pto engine gone threw about two hundred hours ago nice clean tractor [More Ads]

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy