Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 
Marketplace
Classified Ads
Photo Ads
Tractor Parts
Salvage

Community
Discussion Forums
Project Journals
Your Stories
Events Calendar
Hauling Schedule

Galleries
Tractor Photos
Implement Photos
Vintage Photos
Help Identify
Parts & Pieces
Stuck & Troubled
Vintage Ads
Community Album
Photo Ad Archives

Research & Info
Articles
Tractor Registry
Tip of the Day
Safety Cartoons
Tractor Values
Serial Numbers
Tune-Up Guide
Paint Codes
List Prices
Production Nbrs
Tune-Up Specs
Torque Values
3-Point Specs
Glossary

Miscellaneous
Tractor Games
Just For Kids
Virtual Show
Museum Guide
Memorial Page
Feedback Form

Yesterday's Tractors Facebook Page

  
Tractor Talk Discussion Board

Re: Hydraulic Questions


[ Expand ] [ View Replies ] [ Add a Reply ] [ Return to Forum ]

Posted by RodInNS on July 24, 2007 at 19:21:50 from (24.224.246.156):

In Reply to: Hydraulic Questions posted by uncle on July 24, 2007 at 14:51:03:

At this hour I'm not going to figure the volume of that tank, but I'd ballpark it at close to 30 gallons full. It's bigger than my tank for the wetline, and that holds 4 can no problem. Unless you're going to run this thing for hours at a time, I'd say it will be fine. I'm assuming that you're using the standard 1 section pump for this... which is about 25 gpm. Generally, or at least in theory you would size the resevoir to be 3 times the pumps capacity per minute, but on intermittent applications like this it's not needed. A boom truck or log truck with a 2 section pump would be a different story.

Other than that, I'd suggest you go with a 2" suction for the bit more it will cost, and a 1" return filter. Plumb both to the bottom of the tank, and install ball valves on both the suction and return lines so you can disconnect without draining if you ever need to remove the pump. Forget about the suction strainer. It'll create a restriction you don't really need on a suction run like that....
Just don't undersize or compromise the suction. I already bought that badge of honor. It only cost me a pump.... 2 seconds more and it would have cost a PTO too.
Small saddle tanks make great hydraulic tanks if you're handy with welding aluminum. Otherwise, the surplus centers or a truck parts outfit.... or junkyard. I made my tank, but it was made for a spot at the time, and a commercial tank wouldn't fit.

Rod


Replies:




Add a Reply

:
:
: :

:

:

:

: If you check this box, email will be sent to you whenever someone replies to this message. Your email address must be entered above to receive notification. This notification will be cancelled automatically after 2 weeks.


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Today's Featured Article - Show Coverage: Godfrey, Illinois Country Days - by Cindy Ladage. Except for last fourth of July's Old Gold show in Springfield, Illinois, I don't remember when it was so hot. Nevertheless, the heat didn't keep vendors and visitors alike from enjoying the third annual Country Day's Event. Jane Elliott said the event was originally a one man show. "Barry Seiler, owner of Country Town Farm Supply store used to invite people up to the Johne Deere store. He would give hats and a free meal for everyone that brings a tractor." Elliott said while this ... [Read Article]

Latest Ad: Sell 1958 Hi-Altitude Massey Fergerson tractor, original condition. three point hitch pto engine, Runs well, photos available upon request [More Ads]

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy