|
Tractor Talk Discussion Board |
Re: Flail Mower question again
[ Expand ] [ View Replies ] [ Add a Reply ] [ Return to Forum ]
Posted by MarkB_MI on January 26, 2007 at 03:20:23 from (216.234.99.16):
In Reply to: Flail Mower question again posted by 37 chief on January 25, 2007 at 19:18:54:
There are at least two different types of knives used on the older Mott mowers. It sounds like you have the straight knives that are about six inches long. On my Mott F6, I have a different setup that I believe are called "rock and trash" knives. These do a better job handling rough stuff, but they are a far cry from the heavy duty knives used on the newer mowers. It's hard to say if you could use the later style blades, but you can certainly go to the "rock" knives like I have. To switch to the rock and trash knives, you need for each set of knives: 2 ea blades P/N 101993 1 ea D-ring P/N 101991 2 ea Clip P/N 101992 (possibly 102650 or 105746) 1 ea bolt P/N 000032 1 ea self-locking nut P/N 000210 Montage Enterprises carries these parts (or at least used to), but doesn't show them on their web site. Flailmaster shows them on their site. Your best bet is to try to figure out the model number and go to an Alamo dealer or call Montage or Flailmaster to see exactly what setup you can use. Maybe the "coarse-cut" blades will work on your machine, these are much heavier than the "fine-cut" blades I described above. My mower is covered in snow right now, but I believe it has knives mounted every inch. So 72 sets of knives, which would be 144 total, except that the last two rings on each end only have one blade each, so 140 total. If you're going to be doing a lot of heavy brush, I would look at some of the newer machines, which are much heavier. Stuff will wind around the cutter shaft, but generally it will clear itself out. It's not difficult to stop and unwind any weeds, string, saplings, etc. off the shaft. The worst thing I've ever picked up was a garden hose, watch out for those, they are nearly impossible to remove!
Replies:
Home
| Forums
| Order Support
Today's Featured Article -
Memories of a Farmall C - by Monty Bradley. When I was a child, my grandparents lived on a farm owned by a Mr. Walters. The crops raised were cotton and soybeans, with about forty head of mixed breed cattle. Mr. Walters owned two tractors then. A Farmall 300 on gasoline and a Farmall C, that had once belonged to his father-in-law, and had been converted from gasoline to LP Gas. Many times, as a small boy, I would cross the fence behind the house my grandparents lived in and walk down the turn row to where granddaddy would be cultivati
... [Read Article]
Latest Ad:
1958 FORD RARE 4x4 801 TRACTOR, ELENCO/FRONT DRIVE, FRONTLOADER AND WEIGHTED REAR WHEELS, FIVE SPEED, LIVE PTO, GAS ENGINE, NEW REAR WHEELS AND TIRES, ENGINE RUNS.
[More Ads]
Copyright © 1997-2026 Yesterday's Tractor Co. All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V. Yesterday's Tractors - Antique Tractor HeadquartersWebsite Accessibility Policy |
|