|
Tractor Talk Discussion Board |
Re: O/T HOT WATER HEATER POP OFF VALVE
[ Expand ] [ View Replies ] [ Add a Reply ] [ Return to Forum ]
Posted by wdTom on January 05, 2007 at 18:32:58 from (155.212.222.207):
In Reply to: O/T HOT WATER HEATER POP OFF VALVE posted by G Elliot on January 05, 2007 at 16:44:37:
Measure the temperature of your hot water by running it into a tin can or such with an oven thermometer in it. If it isn't near where the water heater is set and or it is too high, reset the waterheater. The cooler you set it the less it will cost to heat your water. 120 is common. You shouldn't neet to go over 140 I don't believe. If this is OK check the pressure in the system with a gauge you know is somewhere near new or reads right. If it is OK, probably not more than 50 or 60psi at most, then it is probably a defective T&P valve. They aren't that expensive, I would buy another rather than try adjusting that one unless you can set it up, " on the bench" so to speak, using a known good gauge. If you have a pump and pressure tank system, that is your own well, you already have an expansion tank in the system. You can check it to see there is an "air coushion" in the tip of it to allow for expansion and to be compressed by the pump as it builds pressure in your system. To test, notice if when your pump comes on it runs for 10 or 15 seconds or so. You should run water until the pump kicks in, then turn off the water and see hown long it takes for pressure to build and the pump shut off. If this only takes a few seconds or no time, you need to put some air in the tank. If it is sealed andhas a bladder, possibly the bladder is broken. If it is just a tank, no bladder you need to add air from time to time anyway. Water absorbs the air over time and caused the pump to short cycle. Most tanks have a air valve like a tire valve in them. If you add too much to a bladder tank you can rupture it. I don't remember how to do it right.
Replies:
Home
| Forums
| Order Support
Today's Featured Article -
The Rescue of a Fordson F - by Anthony West. Introduction I live in the UK and have for many years restored Fordson tractors (in the main model N's). I have also restored and shown model F's, E 27N's, Field Marshall Series 2, David Brown Cropmasters and the old rey Fergeson T 20. At one time I had seven restored examples which were shown and used in ploughing matches. As most restorers, I have a number of war stories I can relate on a range of topics that may help other like minded and interested people. Perhaps my first p
... [Read Article]
Latest Ad:
one 8n and one 9n tractor. totaly restored,pretty much everything is new. one 6ft blade good shape.
[More Ads]
Copyright © 1997-2026 Yesterday's Tractor Co. All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V. Yesterday's Tractors - Antique Tractor HeadquartersWebsite Accessibility Policy |
|