Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 
Marketplace
Classified Ads
Photo Ads
Tractor Parts
Salvage

Community
Discussion Forums
Project Journals
Your Stories
Events Calendar
Hauling Schedule

Galleries
Tractor Photos
Implement Photos
Vintage Photos
Help Identify
Parts & Pieces
Stuck & Troubled
Vintage Ads
Community Album
Photo Ad Archives

Research & Info
Articles
Tractor Registry
Tip of the Day
Safety Cartoons
Tractor Values
Serial Numbers
Tune-Up Guide
Paint Codes
List Prices
Production Nbrs
Tune-Up Specs
Torque Values
3-Point Specs
Glossary

Miscellaneous
Tractor Games
Just For Kids
Virtual Show
Museum Guide
Memorial Page
Feedback Form

Yesterday's Tractors Facebook Page

  
Tractor Talk Discussion Board

Re: cattle waters // Rithie or Jug


[ Expand ] [ View Replies ] [ Add a Reply ] [ Return to Forum ]

Posted by T_Bone on November 23, 2006 at 06:34:44 from (4.240.42.175):

In Reply to: cattle waters // Rithie or Jug posted by Jim WJ on November 21, 2006 at 21:00:07:

Hi Jim,

Here's a post I made on the tool forum. See if this helps you.


You can also use a heat pipe. At 8ft in the ground the temperature is stable year around at 50� in most of the USA.

The second law of thermal dymanics states: "heat flows from a higher source to a colder source"

So install a "insulated" stand pipe (pipe#1) in one end of your tank down thru the frost line for your area in to a larger diameter horizontal pipe at 8ft then return to into another vertical stand pipe (pipe#2) back into the tank above the desired water line.

Water will be drawn from pipe#1 to the under ground horizontal heat pipe thus heating the water to around 45�. The heated water expands and flows back into the stock tank thru pipe#2 as stated by the 2nd law of thermal dymanics.

You will want your supply and return pipes in the center of your tank surrounded by water as the water will be a insulator at that point.

If you look on the net there is a system drawing that uses simular engineering of a hill side water tank. It works close to what I described without any explantion.

There is also another way but you run the risk of having too much hot of water. At one end of the tank install a clear plexy-glass cover sealed to the top of the tank with a veritcal piece towards the bottom of the tank to seperate the hot and cold sides.

The sun will solar heat the enclosed tank end and the cold tank water will move in and out of the solar collector trying to equalize temperature.

You could use Butyl caulk for a gasket sealer and glue to hold the solar glass on. Butyl caulk is some very tuff sealant. If your in snow country then you would want to 45� the collector glazing to the tank horizontal to keep it clean.

T_Bone



Replies:




Add a Reply

:
:
: :

:

:

:

: If you check this box, email will be sent to you whenever someone replies to this message. Your email address must be entered above to receive notification. This notification will be cancelled automatically after 2 weeks.


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums  |  Order Support


Today's Featured Article - Timing Your Magneto Ignition Tractor - by Chris Pratt. If you have done major engine work or restored your tractor, chances are you removed the magneto and spark plug wires and eventually reached the point where you had to put it all back together and make it run. On our first cosmetic restoration, not having a manual, we carefully marked the wires, taped the magneto in the position it came off, and were careful not to turn the engine over while we had these components off. We thought we could get by with this since the engine ran perfectly and would not need any internal work. After the cleanup and painting was done, we began reassembly and finally came to t ... [Read Article]

Latest Ad: 1965 International Harvester McCormick Farmall cub tractor 2,500. Two owner tractor. My grandfather bought new in 1966, then we inherited it. Have all the paperwork original manual and all maintenance records. It starts and moves. Comes with underbelly mower, plough, and some other attachments. [More Ads]

Copyright © 1997-2026 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy