|
Tractor Talk Discussion Board |
Re: Loader counterweight
[ Expand ] [ View Replies ] [ Add a Reply ] [ Return to Forum ]
Posted by Billy NY on September 19, 2006 at 09:30:57 from (205.188.117.14):
In Reply to: Loader counterweight posted by Rob in Ore on September 18, 2006 at 13:31:34:
I'm not familiar with the 240, must one up the line from the 140 ? Utility size. I run my 850 ford with a cast iron counter weight, that appears to have been manufactured for this purpose. It's got a multi-hole drawbar attached to it, and is what the lift arms attach to. It's thick at the end closest to the tractor and thinner at the back, sloped with a gentle radius, on the bottom side, and being cast it is real heavy, must be over 1000 lbs. The tires are loaded too. I noticed that even with the tires loaded, the tractor was useless in the snow, unless it had chains, but when I put that weight on, it gets good traction in the snow, if there is ice under it, you still need chains, but I was suprised at the difference in performance. The thing I like about this counterweight is that it's compact but heavy, and I can keep it below the rear axle, lower the better, probably stabilizes and applies the weight better. It's also set up so that the strain on the hydraulics is relieved, it has an old backhoe frame for a sherman hoe or similar, so I can rest a steel bar across and take the weight. I would imagine you can buy something fabricated of steel that connects to the 3pt. to do the same, I have thought I've seen something like that before. A lot of people use the conrcrete in the barrel, I just like the smaller compact weight that came from our old ford dealership, I've never seen another one, sure glad I found it in the weeds and have it to use now, in deep snow and muck it seems to get me through, tires are new also, but you have to be careful about slipping/spinning them with the weight on if you have rocks in the soil or muck. Frozen grounda that has thawed a bit seems to slice the tires easily if you spin them, have to be careful about that.
Replies:
Home
| Forums
| Order Support
Today's Featured Article -
Converting from 6 Volt to 12 Volt - by Chris Pratt. It's a common problem for old machines especially when the weather starts to dip below 40 and the tractor isn't fired up as often. You are probably used to the 12 volt Diehard, charged with 200 amp alternator of your 3/4 ton that always is ready and always starts. It's this type of experience that brings about the many queries we get for 12-volt conversion kits. Since only a few kits are available (we sell kits for the
... [Read Article]
Latest Ad:
Late 50s early 60s international harvester 560 with cultivator
[More Ads]
Copyright © 1997-2026 Yesterday's Tractor Co. All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V. Yesterday's Tractors - Antique Tractor HeadquartersWebsite Accessibility Policy |
|