|
Tractor Talk Discussion Board |
Re: A little O/T need ideas of how to build a goat
[ Expand ] [ View Replies ] [ Add a Reply ] [ Return to Forum ]
Posted by KEH on September 03, 2006 at 14:24:01 from (209.213.17.113):
In Reply to: Re: A little O/T need ideas of how to build a goat posted by old on September 03, 2006 at 13:06:48:
Old, Assuming the 3 ft. sides are solid, you are half way there. Using light angle iron such as bed rails(which are hard steel) extend sides up to proper height, which is high enough to keep from hitting head when you walk into trailer(top must be covered for goats). Reccomend 2 ft. spacing for uprights. Tie uprights together at top with more angle iron or pipe. Get what TSC lists as "feedlot panels". These are heavy mesh made from about 1/4 diameter wire and come in 16 ft. lengths. Get an appropriate amount and cut to fit, welding on the inside of your frame, sides, top and front. Get as small a mesh as possible. The TSC catalogue lists hog panels at 34 inches high, combo at 52 inches high and cattle at 52 inches high. Horse panel is listed at 8 ft high with 2 in. by 4 in. mesh. Make rear gate. A simple swinging gate which opens both ways with appropriate top and bottom latches should be enough. Be sure to have the bottom of the gate solid like the sides and front. I'm sure you know this, but I will mention anyway that the reason for solid sides is so that the animal can't get a foot through the side and get hurt. If the trailor has that expanded steel on the side, thats OK for solid sides. I have just been looking into building a light single axle cattle trailor for hauling one or two calves behind a light pickup since the livestock barn 10 miles away I have been selling at has closed and I now have a 50 mile haul. Don't want to go that distance in the large truck and trailer for one or two head because of gas milage issues. Hope this helps. KEH
Replies:
Home
| Forums
| Order Support
Today's Featured Article -
Madison's County - by Anthony West. Philip Madison has been a good friend of mine for quite some time. He has patiently suffered my incessant chit chat on the subject of tractors for longer than I care to remember, and on many occasions he has put himself out, dropped what ever it was he was doing, to come and lend a hand cranking handles, or loading a find onto a trailer. Although he himself has never actually owned or restored a tractor, he was always enthusiastic and always around helping with other peoples projects.
... [Read Article]
Latest Ad:
1965 International Harvester McCormick Farmall cub tractor 2,500. Two owner tractor. My grandfather bought new in 1966, then we inherited it. Have all the paperwork original manual and all maintenance records. It starts and moves. Comes with underbelly mower, plough, and some other attachments.
[More Ads]
Copyright © 1997-2026 Yesterday's Tractor Co. All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V. Yesterday's Tractors - Antique Tractor HeadquartersWebsite Accessibility Policy |
|