Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 
Marketplace
Classified Ads
Photo Ads
Tractor Parts
Salvage

Community
Discussion Forums
Project Journals
Your Stories
Events Calendar
Hauling Schedule

Galleries
Tractor Photos
Implement Photos
Vintage Photos
Help Identify
Parts & Pieces
Stuck & Troubled
Vintage Ads
Community Album
Photo Ad Archives

Research & Info
Articles
Tractor Registry
Tip of the Day
Safety Cartoons
Tractor Values
Serial Numbers
Tune-Up Guide
Paint Codes
List Prices
Production Nbrs
Tune-Up Specs
Torque Values
3-Point Specs
Glossary

Miscellaneous
Tractor Games
Just For Kids
Virtual Show
Museum Guide
Memorial Page
Feedback Form

Yesterday's Tractors Facebook Page

  
Tractor Talk Discussion Board

Re: Super A wiring diagram/6volt to 12 volt


[ Expand ] [ View Replies ] [ Add a Reply ] [ Return to Forum ]

Posted by John T on July 30, 2006 at 15:52:25 from (66.244.90.5):

In Reply to: Super A wiring diagram/6volt to 12 volt posted by Robert Switzer on July 30, 2006 at 15:24:46:

Robert, If thats a One Wire Alternator as your post suggests, its output wires to the Load (NOT to battery/starter) side of the ammeter. That same Load side ammeter terminal is what provides input voltage to loads like the BAT input terminal on any light or ignition switches. The ammeters other Supply side terminal gets fed from the hot ungrounded battery post, usually via the big batery cable terminal on a starter switch. From the IGN output terminal on the ignition switch should first be the external Ballast Resistor (assuming you have one) and then the coils high side input terminal, which should be + on a Negative grounded tractor. The coils other - terminal is what wires to the distributor. If youre running the original 6 volt coil and an external ballast resistor, the ballast normally gets quite hot but the coil should only be warm. If the ballast is wired correct in series before the coil AND IF ITS THE CORRECT OHMS RESISTANCE, the coil shouldnt be so hot you cant lay your hand on it, only warm as mentioned.

This all assumes you mean its the Ballast thats hot instead of any light switch resistors, is that what you meant?????? If you used to have a genny with a 2 wire cutout relay and the light switch field current control system, that resistor/terminal should not be used if you changed to an alternator. This also assumes its a One Wire alternator as you indicated and it was converted to negative ground as most all alternators are.

Let us know, best wishes n God Bless, post back any questions

John T


Replies:




Add a Reply

:
:
: :

:

:

:

: If you check this box, email will be sent to you whenever someone replies to this message. Your email address must be entered above to receive notification. This notification will be cancelled automatically after 2 weeks.


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Today's Featured Article - Show Coverage: Godfrey, Illinois Country Days - by Cindy Ladage. Except for last fourth of July's Old Gold show in Springfield, Illinois, I don't remember when it was so hot. Nevertheless, the heat didn't keep vendors and visitors alike from enjoying the third annual Country Day's Event. Jane Elliott said the event was originally a one man show. "Barry Seiler, owner of Country Town Farm Supply store used to invite people up to the Johne Deere store. He would give hats and a free meal for everyone that brings a tractor." Elliott said while this ... [Read Article]

Latest Ad: Sell 1958 Hi-Altitude Massey Fergerson tractor, original condition. three point hitch pto engine, Runs well, photos available upon request [More Ads]

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy