Tractor Talk Discussion Board |
Re: Converting to alternator
[ Expand ] [ View Replies ] [ Add a Reply ] [ Return to Forum ]
Posted by John T on June 20, 2006 at 06:09:58 from (66.244.90.5):
In Reply to: Converting to alternator posted by Ray Rooney on June 20, 2006 at 05:45:07:
WIRING A GM 10SI 3 WIRE ALTERNATOR ON A COIL TYPE GAS ENGINE WITH NEGATIVE GROUND This is for a GM 10 SI Negative Ground 3 wire alternator to excite it to make it work like a one wire alternator. FOR NEGATIVE GROUND ONLY Run a 16 Gauge or so wire from the Ignition switches IGN terminal (what feeds the coil when ON) with a series 10 ohm 5 watt current limiting protection resistor to the lil No. 1 terminal on the Alternators side. (Excitation circuit) NOTE these ratings I use may be bigger than actually required, but the higher rated units have bigger leads easier to wire up. Thennnnnnnnn if when you turn the ignition off she still runs from backfeed, add in a series 5 amp 50 PIV Volt Diode (IT MUST be wired + anode end to switch, - cathode end to alternator). Run a 16 Gauge wire from the Alternators lil side No. 2 terminal jumped up to the big main rear output post. (Sensing circuit) It may be a lil more accurate to sense directly off the batterys + terminal, but this is much easier. Run a 10 Gauge wire from the Alternators big output post up to the Load (NOT to battery) side of ammeter (if it has an ammeter). If theres only a 12 Gauge wire from the ammeters other Supply terminal to the battery or starter etc., I replace it with a 10 gauge. NOTES: On a diesel where theres no coil and ignition switch I excite the alternator via an oil pressure switch. If the tractor uses an Idiot Light instead of an ammeter, it can be used to serve as the excitation voltage circuit to the alternators lil No. 1 side terminal. John T Nordhoff in Indiana, retired electrical engineer
Replies:
Home
| Forums
Today's Featured Article -
My Ford Golden Jubilee - by Troy Estes. This article is about my '53 Ford Jubilee and a story that starts with taking the tractor to my brother's Starter/Alternator Rebuilding shop for a wiring fix. The generator was shot as well as all the wiring. I dropped off the tractor expecting a transformation from a 6 volt to a 12 volt system utilizing the original generator housing, and a total rewiring of the whole tractor. The front end center pin bushing was worn also so I ask that they replace it if they had time. Well, that’s wha
... [Read Article]
Latest Ad:
1964 I-H 140 tractor with cultivators and sidedresser. Starts and runs good. Asking 2650. CALL RON AT 502-319-1952
[More Ads]
Copyright © 1997-2025 Yesterday's Tractor Co. All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V. Yesterday's Tractors - Antique Tractor HeadquartersWebsite Accessibility Policy |
|