Tractor Talk Discussion Board |
Re: Getting my feet wet...
[ Expand ] [ View Replies ] [ Add a Reply ] [ Return to Forum ]
Posted by Jonfarmer on June 12, 2006 at 18:41:25 from (165.121.144.15):
In Reply to: Getting my feet wet... posted by Josh Lafond on June 12, 2006 at 15:08:25:
Anything with a 6 cylinder engine does the best right out of the box because they have excellent lugging ability and will hang in there that extra distance. Oilver 70, 77, 770, 88, 880, some of the Cockshutts had 6 cylinders as well, like a 570 turbo, now thats a puller!. Farmall H's and M's do good as well. I doubt you want a small one like a C or smaller like someone mentioned, those don't have much power or make much noise and thats part of the excitment for me. The Allis Chalmers WD and WD45 make excellent pullers too. The 2cyl JD make poor pullers in my opinion, they don't have much lugging ability like the others and depend on that big flywheel to keep going, but usually a good 4cyl Farmall of the same size (Farmall M V.S JD A or Farmall H V.S JD B)will beat it unless alot of money is spent modifying the Deere. The right tractor for you is what ever it is that you like, you say that you have been to the pulls and watched, so you must have an idea of a certain model tractor you would like. Now even if you follow my suggestions and buy yourself a good puller, you more than likely will not win the first pull you go to, since pulling is actually a bit of a science as well, you need to find where to put your weights for the best effects, finding the right gear, play around with the tire pressure, different width and tread tires, get your hitch within the rules and the most beneficial to the tractor, alittle luck sure helps too as you need to find some good traction to the track to effectivly get your horsepower to the ground. The key is to have fun, the prizes are not much and it's usually a $5 plastic trophy or a ribbon, or a t-shirt, and about $20 cash for first place, so buy what you like because it is not so much about winning.
Replies:
Home
| Forums
Today's Featured Article -
Product Review: JB Weld - by Staff. JB Weld is basically an epoxy glue that does an exceptionally good job of bonding to cast iron and steel along with several other materials. As I mentioned, it is so common that I have yet to buy a tractor that did not have JB Weld used somewhere. It is sometimes used so well you can't tell its there and other times used as a sloppy quick fix. Finding where and how it can be used correctly is key to whether you are using it as an "inelegant hack" or an integral solution to difficult and expens
... [Read Article]
Latest Ad:
1945 Farmall wide body gas with pto and front plow. Runs good but needs new points.
[More Ads]
Copyright © 1997-2024 Yesterday's Tractor Co. All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V. Yesterday's Tractors - Antique Tractor HeadquartersWebsite Accessibility Policy |
|