Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 
Marketplace
Classified Ads
Photo Ads
Tractor Parts
Salvage

Community
Discussion Forums
Project Journals
Your Stories
Events Calendar
Hauling Schedule

Galleries
Tractor Photos
Implement Photos
Vintage Photos
Help Identify
Parts & Pieces
Stuck & Troubled
Vintage Ads
Community Album
Photo Ad Archives

Research & Info
Articles
Tractor Registry
Tip of the Day
Safety Cartoons
Tractor Values
Serial Numbers
Tune-Up Guide
Paint Codes
List Prices
Production Nbrs
Tune-Up Specs
Torque Values
3-Point Specs
Glossary

Miscellaneous
Tractor Games
Just For Kids
Virtual Show
Museum Guide
Memorial Page
Feedback Form

Yesterday's Tractors Facebook Page

  
Tractor Talk Discussion Board

Re: Barn door location?


[ Expand ] [ View Replies ] [ Add a Reply ] [ Return to Forum ]

Posted by MarkB_MI on April 01, 2006 at 05:47:33 from (64.31.10.17):

In Reply to: Barn door location? posted by Nathan in Texas on March 31, 2006 at 08:19:48:

My shop is 30x40 with 10' sidewalls. Yes, it filled up quickly, but I still don't think I would have gone bigger if I had it to do over again. I might have gone with 12' sidewalls so I could put in a lift.

If you put in two big doors, it will be easier to get stuff in and out, but you will lose a lot of wall space. Because of where my shop is located, I could only put in one door. It's sometimes a problem to get stuff in and out, but it's not that big of a deal.

How high are your sidewalls, and how high will your doors be? Overhead doors normally need at least a foot of overhead, plus another foot for the opener. Which means 8 feet is about it in a 10' sidewall building. A sliding door needs no overhead, so you can have a 10' tall door in the end of a 10' sidewall building. (You can't get a full height slider in the side of pole barn because you lose a foot to the headers.)

I put my entry door in the end of the building so I don't get soaked when it's raining. (No gutters to clean.) I put it on to the right of the overhead door (as you face the building) so if I'm pulling a vehicle in I don't have to walk to the other side of the vehicle to get to the entry door. Coincidentally the door is at the corner closest to the house.

I put in a 16' wide by 8' tall overhead door exactly in the center of the end of the building. I definitely would not go with a narrower door. You want to be able to get in and out when there's a disabled vehicle in the building.

Good luck.


Replies:




Add a Reply

:
:
: :

:

:

:

: If you check this box, email will be sent to you whenever someone replies to this message. Your email address must be entered above to receive notification. This notification will be cancelled automatically after 2 weeks.


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Today's Featured Article - The Nuts and Bolts of Fasteners - Part 2 - by Curtis Von Fange. In our previous article we discussed capscrews, bolts, and nuts along with their relative hardness and thread sizes. In this segment we will finish up on our fasteners and then work with ways to keep them from loosening up in the field. Capscrews, bolts and nuts are not the only means of holding two parts together. When dealing with thinner metals like sheet tin, a long bolt and ... [Read Article]

Latest Ad: Oliver 550 Diesel runs like a watch three point hitch pto engine gone threw about two hundred hours ago nice clean tractor [More Ads]

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy